A lower mass for the exoplanet WASP-21b

We present high-precision transit observations of the exoplanet WASP-21b, obtained with the Rapid Imager to Search for Exoplanets instrument mounted on the 2.0-m Liverpool Telescope. A transit model is fitted, coupled with a Markov chain Monte Carlo routine, to derive accurate system parameters. The two new high-precision transits allow us to estimate the stellar density directly from the light curve. Our analysis suggests that WASP-21 is evolving off the main sequence which led to a previous overestimation of the stellar density. Using isochrone interpolation, we find a stellar mass of 0.86 ± 0.04 Msun, which is significantly lower than previously reported (1.01 ± 0.03 Msun). Consequently, we find a lower planetary mass of 0.27 ± 0.01 MJup. A lower inclination (87?4 ± 0?3) is also found for the system than previously reported, resulting in a slightly larger stellar (R*= 1.10 ± 0.03 Rsun) and planetary radius (Rp= 1.14 ± 0.04 RJup). The planet radius suggests a hydrogen/helium composition with no core which strengthens the correlation between planetary density and host star metallicity. A new ephemeris is determined for the system, i.e. T0= 245 5084.519 74 ± 0.000 20 (HJD) and P= 4.322 5060 ± 0.000 0031 d. We found no transit timing variations in WASP-21b.

A case study with a novel geometry for pulsed laser deposition

Aluminium thin films were deposited by a laser ablation technique from solid cylindrical targets rotated on a lead screw. Both smooth-surfaced targets and targets with screw threads cut into the area to he irradiated were used. The targets were irradiated with a focused circular spot size of 2.5 mm in diameter, at a power density equal to 5.4 +/- 0.2 x 10(8) W cm(-2). The polar distribution of the ablated atomic material was found to vary as a function of the target screw thread pitch, with the exponent n, in the polar distribution f(theta) = cos(n) theta, varying from 13.5 +/- 1.3 for no pitch to a minimum of 5 +/- 0.7 for a screw thread pitch of 0.2 mm. The use of such novel target geometries forms a possible basis for increasing thickness uniformity during the pulsed laser deposition of thin films.

Design optimization of cold-formed steel portal frames taking into account the effect of building topology

Cold-formed steel portal frames are a popular form of construction for low-rise commercial, light industrial and agricultural buildings with spans of up to 20 m. In this article, a real-coded genetic algorithm is described that is used to minimize the cost of the main frame of such buildings. The key decision variables considered in this proposed algorithm consist of both the spacing and pitch of the frame as continuous variables, as well as the discrete section sizes.A routine taking the structural analysis and frame design for cold-formed steel sections is embedded into a genetic algorithm. The results show that the real-coded genetic algorithm handles effectively the mixture of design variables, with high robustness and consistency in achieving the optimum solution. All wind load combinations according to Australian code are considered in this research. Results for frames with knee braces are also included, for which the optimization achieved even larger savings in cost.

The geometry of unstented and stented pig common carotid artery bypass grafts

The long-term success of arterial bypass grafting with autologous saphenous veins is limited by neointimal hyperplasia (NIH), which seemingly develops preferentially at sites where hydrodynamic wall shear is low. Placement of a loose-fitting, porous stent around end-to-end, or end-to-side, autologous saphenous vein grafts on the porcine common carotid artery has been found significantly to reduce NIH, but the mechanism is unclear. In a preliminary study, we implanted autologous saphenous vein grafts bilaterally on the common carotid arteries of pigs, placing a stent around one graft and leaving the contralateral graft unstented. At sacrifice 1 month post implantation, the grafts were pressure fixed in situ and resin casts were made. Unstented graft geometry was highly irregular, with non-uniform dilatation, substantial axial lengthening, curvature, kinking, and possible long-pitch helical distortion. In contrast, stented grafts showed no major dilatation, lengthening or curvature, but there was commonly fine corrugation, occasional slight kinking or narrowing of segments, and possible long-pitch helical distortion. Axial growth of grafts against effectively tethered anastomoses could account for these changes. CFD studies are planned, using 3D MR reconstructions, on the effects of graft geometry on the flow. Abnormality of the flow could favour the development of vascular pathology, including NIH.

Electronic properties of zircon and hafnon from many-body perturbation theory

The electronic properties of zircon and hafnon, two wide-gap high-kappa materials, are investigated using many-body perturbation theory (MBPT) combined with the Wannier interpolation technique. For both materials, the calculated band structures differ from those obtained within density-functional theory and MBPT by (i) a slight displacement of the highest valence-band maximum from the Gamma point and (ii) an opening of the indirect band gap to 7.6 and 8.0 eV for zircon and hafnon, respectively. The introduction of vertex corrections in the many-body self-energy does not modify the results except for a global rigid shift of the many-body corrections.

Shape corrections to exchange-correlation potentials by gradient-regulated seamless connection of model potentials for inner and outer region

Shape corrections to the standard approximate Kohn-Sham exchange-correlation (xc) potentials are considered with the aim to improve the excitation energies (especially for higher excitations) calculated with time-dependent density functional perturbation theory. A scheme of gradient-regulated connection (GRAC) of inner to outer parts of a model potential is developed. Asymptotic corrections based either on the potential of Fermi and Amaldi or van Leeuwen and Baerends (LB) are seamlessly connected to the (shifted) xc potential of Becke and Perdew (BP) with the GRAC procedure, and are employed to calculate the vertical excitation energies of the prototype molecules N-2, CO, CH2O, C2H4, C5NH5, C6H6, Li-2, Na-2, K-2. The results are compared with those of the alternative interpolation scheme of Tozer and Handy as well as with the results of the potential obtained with the statistical averaging of (model) orbital potentials. Various asymptotically corrected potentials produce high quality excitation energies, which in quite a few cases approach the benchmark accuracy of 0.1 eV for the electronic spectra. Based on these results, the potential BP-GRAC-LB is proposed for molecular response calculations, which is a smooth potential and a genuine "local" density functional with an analytical representation. (C) 2001 American Institute of Physics.

Neonatal facial and cry responses to invasive and non-invasive procedures

Evaluation of pain in neonates is difficult due to their limited means of communication. The aim was to determine whether behavioural reactions of cry and facial activity provoked by an invasive procedure could be discriminated from responses to non-invasive tactile events. Thirty-six healthy full-term infants (mean age 2.2 h) received 3 procedures in counterbalanced order: intramuscular injection, application of triple dye to the umbilical stub, and rubbing thigh with alcohol. Significant effects of procedure were found for total face activity and latency to face movement. A cluster of facial actions comprised of brow bulging, eyes squeezed shut, deepening of the naso-labial furrow and open mouth was associated most frequently with the invasive procedure. Comparisons between the 2 non-invasive procedures showed more facial activity to thigh swabbing and least to application of triple dye to the umbilical cord. Acoustic analysis of cry showed statistically significant differences across procedures only for latency to cry and cry duration for the group as a whole. However, babies who cried to two procedures showed higher pitch and greater intensity to the injection. There were no significant differences in melody, dysphonation, or jitter. Methodological difficulties for investigators in this area were examined, including criteria for the selection of cries for analysis, and the logical and statistical challenges of contrasting cries induced by different conditions when some babies do not always cry. It was concluded that facial expression, in combination with short latency to onset of cry and long duration of first cry cycle typifies reaction to acute invasive procedures.

Blown Jet Vortex Generator Control of a Separated Diffuser Flow

The application of blown jet vortex generators to control flow separation in a diffuser with an opening angle of 10° has been studied using the computational fluid dynamics (CFD) code Fluent 6™. Experimental data is available for the uncontrolled flow in the diffuser. The section of the duct upstream of the diffuser has a height H equal to 15 mm; its length and breadth are 101H and 41H respectively; the diffuser has an expansion ratio of 4.7:1. Fully developed flow is achieved upstream of the diffuser. Pipes of diameters equal to 1.5%, 2.5% and 5% of H were considered; pitch angle was constant at 45° and yaw angle was fixed at 60°; velocity ratio was varied from 1.7 to 8.0; both co-rotating and counter-rotating arrays were studied. The best results were obtained with a counter-rotating array of generators with a hole diameter of 5% of H and a velocity ratio of 3.7.

Entanglement control via reservoir engineering in ultracold atomic gases

We study the entanglement of two impurity qubits immersed in a Bose-Einstein condensate (BEC) reservoir. This open quantum system model allows for interpolation between a common dephasing scenario and an independent dephasing scenario by modifying the wavelength of the superlattice superposed to the BEC, and how this influences the dynamical properties of the impurities. We demonstrate the existence of rich dynamics corresponding to different values of reservoir parameters, including phenomena such as entanglement trapping, revivals of entanglement, and entanglement generation. In the spirit of reservoir engineering, we present the optimal BEC parameters for entanglement generation and trapping, showing the key role of the ultracold-gas interactions. Copyright (C) EPLA, 2013

Design and testing of transonic linear cascade tunnel with optimized slotted walls

In linear cascade wind tunnel tests, a high level of pitchwise periodicity is desirable to reproduce the azimuthal periodicity in the stage of an axial compressor or turbine. Transonic tests in a cascade wind tunnel with open jet boundaries have been shown to suffer from spurious waves, reflected at the jet boundary, that compromise the flow periodicity in pitch. This problem can be tackled by placing at this boundary a slotted tailboard with a specific wall void ratio s and pitch angle a. The optimal value of the s-a pair depends on the test section geometry and on the tunnel running conditions. An inviscid two-dimensional numerical method has been developed to predict transonic linear cascade flows, with and without a tailboard, and quantify the nonperiodicity in the discharge. This method includes a new computational boundary condition to model the effects of the tailboard slots on the cascade interior flow. This method has been applied to a six-blade turbine nozzle cascade, transonically tested at the University of Leicester. The numerical results identified a specific slotted tailboard geometry, able to minimize the spurious reflected waves and regain some pitchwise flow periodicity. The wind tunnel open jet test section was redesigned accordingly. Pressure measurements at the cascade outlet and synchronous spark schlieren visualization of the test section, with and without the optimized slotted tailboard, have confirmed the gain in pitchwise periodicity predicted by the numerical model. Copyright © 2006 by ASME.

Tri-axial accelerometers tease apart discrete behaviours in the common cuttlefish Sepia officinalis

Acceleration data loggers can be used to construct time-energy budgets or identify specific behaviours in free living animals. Within a marine context such devices have been largely deployed on vertebrates with comparatively little attention paid to commercially important invertebrates such as cephalopod molluscs. Here we tested the utility of tri-axial accelerometers to tease apart six discrete behaviours in the common cuttlefish Sepia officinalis. By considering depth profiles in conjunction with body pitch and roll and overall dynamic body acceleration we were able to make distinctions between resting at the seabed, active swimming, mating, post-coital panting and active manoeuvring along the seabed. © 2012 Marine Biological Association of the United Kingdom.

Auditory gist: Recognition of very short sounds from timbre cues

Sounds such as the voice or musical instruments can be recognized on the basis of timbre alone. Here, sound recognition was investigated with severely reduced timbre cues. Short snippets of naturally recorded sounds were extracted from a large corpus. Listeners were asked to report a target category (e.g., sung voices) among other sounds (e.g., musical instruments). All sound categories covered the same pitch range, so the task had to be solved on timbre cues alone. The minimum duration for which performance was above chance was found to be short, on the order of a few milliseconds, with the best performance for voice targets. Performance was independent of pitch and was maintained when stimuli contained less than a full waveform cycle. Recognition was not generally better when the sound snippets were time-aligned with the sound onset compared to when they were extracted with a random starting time. Finally, performance did not depend on feedback or training, suggesting that the cues used by listeners in the artificial gating task were similar to those relevant for longer, more familiar sounds. The results show that timbre cues for sound recognition are available at a variety of time scales, including very short ones.

Processing of short auditory stimuli:The rapid audio sequential presentation paradigm (RASP)

Human listeners seem to be remarkably able to recognise acoustic sound sources based on timbre cues. Here we describe a psychophysical paradigm to estimate the time it takes to recognise a set of complex sounds differing only in timbre cues: both in terms of the minimum duration of the sounds and the inferred neural processing time. Listeners had to respond to the human voice while ignoring a set of distractors. All sounds were recorded from natural sources over the same pitch range and equalised to the same duration and power. In a first experiment, stimuli were gated in time with a raised-cosine window of variable duration and random onset time. A voice/non-voice (yes/no) task was used. Performance, as measured by d', remained above chance for the shortest sounds tested (2 ms); d's above 1 were observed for durations longer than or equal to 8 ms. Then, we constructed sequences of short sounds presented in rapid succession. Listeners were asked to report the presence of a single voice token that could occur at a random position within the sequence. This method is analogous to the "rapid sequential visual presentation" paradigm (RSVP), which has been used to evaluate neural processing time for images. For 500-ms sequences made of 32-ms and 16-ms sounds, d' remained above chance for presentation rates of up to 30 sounds per second. There was no effect of the pitch relation between successive sounds: identical for all sounds in the sequence or random for each sound. This implies that the task was not determined by streaming or forward masking, as both phenomena would predict better performance for the random pitch condition. Overall, the recognition of familiar sound categories such as the voice seems to be surprisingly fast, both in terms of the acoustic duration required and of the underlying neural time constants.

Prediction of Transonic LCOs using an Aeroelastic Harmonic Balance Method

This work proposes a novel approach to compute transonic Lim
it Cycle Oscillations using high fidelity analysis. CFD based Harmonic Balance methods have proven to be efficient tools to predict periodic phenomena. This paper’s contribution is to present a new methodology to determine the unknown frequency of oscillations, enabling HB methods to accurately capture Limit Cycle Oscillations (LCOs); this is achieved by defining a frequency updating procedure based on a coupled CFD/CSD Harmonic Balance formulation to find the LCO condition. A pitch/plunge aerofoil and delta wing aerodynamic and respective linear structural models are used to validate the new method against conventional time-domain simulations. Results show consistent agreement between the proposed and time-marching methods for both LCO amplitude and frequency, while producing at least one order of magnitude reduction in computational time.

Prediction of Limit Cycle Oscillations Using an Implicit Aeroelastic-Harmonic Balance Method

This work proposes a extends a novel approach to compute tran sonic Limit Cycle Oscillations using high fidelity analysis. CFD based Harmonic Balance methods have proven to be efficient tools to predict periodic phenomena. This paper’s contribution is to present a methodology to determine the unknown frequency of oscillations using an implicit for- mulation of the HB method to accurately capture Limit Cycle Oscillations (LCOs); this is achieved by defining a frequency updating procedure based on a coupled CFD/CSD Harmonic Balance formulation to find the LCO condition. A pitch/plunge aerofoil and respective linear structural models is used to exercise the new method. Results show consistent agreement between the proposed and time-marching methods for both LCO amplitude and frequency.