Laboratory Investigation of Diluted Bitumen Trapping and Dissolution in Gravel

The Canadian economy is largely dependent on the distribution of large volumes of oil to domestic and international markets by a long network of pipelines. Unfortunately, accidents occur, and oil can leak or spill from these pipelines before it reaches its destination. Of particular concern are the long-term consequences of oil spills in freshwater, which include sinking of oil in water and the contamination of sensitive areas, such as where fish (e.g., salmon) deposit their eggs in gravel-dominated river sediments. There is a knowledge gap regarding the fate and behaviour of oil in river sediment. To this end, this study aimed at finding the potential for diluted bitumen (dilbit) oil to become trapped in gravel and to transfer hydrocarbons into water by dissolution, which are harmful to aquatic life. Two sets of laboratory experiments were conducted to simulate conditions of an oil spill on an exposed bank or in shallow water. In the first set, by conducting capillary pressure-saturation (Pc-Sw) experiments it was found that dilbit can enter gravel pores without much resistance and approximately 14% of the pore volume can be occupied by discontinuous single or multipore blobs of dilbit following imbibition of water. Air-water Pc-Sw experiments done in laboratory 1-D columns required gravity correction and could be successfully scaled to predict dilbit-water Pc-Sw curves, except for the trapped amount of dilbit. Trapped dilbit constituents can be dissolved into the water flowing through gravel pores (hyporheic flow) at different velocities. In the second set, dissolution experiments suggested that for the duration of the test, hydrocarbons that cause acute toxicity dissolve rapidly, likely resulting in a decrease in their effective solubility. However, dilbit saturation changed only <2% within that time. Chronically toxic PAH compounds were also detected in the effluent water. The total concentration of all detected PAHs and alkylPAHs exceeded the threshold literature value to protect early-life stage fish. Observations of decreased concentrations with increased aqueous velocities as well as less than equilibrium concentrations indicated that the mass transfer was rate-limited. A correlation was developed for the mass transfer rate coefficient to understand the mass transfer behaviour beyond the conditions used in the experiments, which had a Reynolds number exponent similar to the studies of NAPL dissolution in groundwater.

Variationelle Zeitdiskretisierungen höherer Ordnung der Konvektions-Diffusions-Reaktions-Gleichungen in zeitabhängigen Gebieten

Wir betrachten zeitabhängige Konvektions-Diffusions-Reaktions-Gleichungen in zeitabhängi- gen Gebieten, wobei die Bewegung des Gebietsrandes bekannt ist. Die zeitliche Entwicklung des Gebietes wird durch die ALE-Formulierung behandelt, die die Nachteile der klassischen Euler- und Lagrange-Betrachtungsweisen behebt. Die Position des Randes und seine Geschwindigkeit werden dabei so in das Gebietsinnere fortgesetzt, dass starke Gitterdeformationen verhindert werden. Als Zeitdiskretisierungen höherer Ordnung werden stetige Galerkin-Petrov-Verfahren (cGP) und unstetige Galerkin-Verfahren (dG) auf Probleme in zeitabhängigen Gebieten angewendet. Weiterhin werden das C 1 -stetige Galerkin-Petrov-Verfahren und das C 0 -stetige Galerkin- Verfahren vorgestellt. Deren Lösungen lassen sich auch in zeitabhängigen Gebieten durch ein einfaches einheitliches Postprocessing aus der Lösung des cGP-Problems bzw. dG-Problems erhalten. Für Problemstellungen in festen Gebieten und mit zeitlich konstanten Konvektions- und Reaktionstermen werden Stabilitätsresultate sowie optimale Fehlerabschätzungen für die nachbereiteten Lösungen der cGP-Verfahren und der dG-Verfahren angegeben. Für zeitabhängige Konvektions-Diffusions-Reaktions-Gleichungen in zeitabhängigen Gebieten präsentieren wir konservative und nicht-konservative Formulierungen, wobei eine besondere Aufmerksamkeit der Behandlung der Zeitableitung und der Gittergeschwindigkeit gilt. Stabilität und optimale Fehlerschätzungen für die in der Zeit semi-diskretisierten konservativen und nicht-konservativen Formulierungen werden vorgestellt. Abschließend wird das volldiskretisierte Problem betrachtet, wobei eine Finite-Elemente-Methode zur Ortsdiskretisierung der Konvektions-Diffusions-Reaktions-Gleichungen in zeitabhängigen Gebieten im ALE-Rahmen einbezogen wurde. Darüber hinaus wird eine lokale Projektionsstabilisierung (LPS) eingesetzt, um der Konvektionsdominanz Rechnung zu tragen. Weiterhin wird numerisch untersucht, wie sich die Approximation der Gebietsgeschwindigkeit auf die Genauigkeit der Zeitdiskretisierungsverfahren auswirkt.

Resolved Stars' Insights into Galaxy Physics

Thesis (Ph.D.)--University of Washington, 2016-08

O processo de institucionalização do curso de administração a distância da UFRN

This work aims to describe how is occurring through the process of institutionalizing the Administration distance course of UFRN. To this end, structured into two parts: through research and analysis of content, sought to impound as if gave historic process of creation, as well as identify variables isomórficas, proposed by Powell and DiMaggio (1991), on the actions undertaken, and still present, institutional actors-having been found three typologies; then investigated the process itself, analyzing the factors of institutionalization suggested Esman (1966-1972), internal structure doctrine, leadership programme, resources, links and exchanges, from the political plan educational course. As the research methodology was defined as qualitative, even though I used survey to collect, reviewed the second ANOVA. The results found in this step pointed out that only the doctrine and internal structure variables are consistent with the assumptions of model; we found for other, discharged indicated a gap between the political acts contemplated in teaching and the actions taken so far, unfavourable element to its legitimacy. However, although the implications found in the analysis of these factors suggest that this course can derive one more discontinuous Government proposal of distance course, this study believes that are still reasonable assistance to facilitate and promote the process aimed at strengthening the progress achieved so far in the success of its institutionalization

Modeling of burden distribution in the blast furnace

The blast furnace is the main ironmaking production unit in the world which converts iron ore with coke and hot blast into liquid iron, hot metal, which is used for steelmaking. The furnace acts as a counter-current reactor charged with layers of raw material of very different gas permeability. The arrangement of these layers, or burden distribution, is the most important factor influencing the gas flow conditions inside the furnace, which dictate the efficiency of the heat transfer and reduction processes. For proper control the furnace operators should know the overall conditions in the furnace and be able to predict how control actions affect the state of the furnace. However, due to high temperatures and pressure, hostile atmosphere and mechanical wear it is very difficult to measure internal variables. Instead, the operators have to rely extensively on measurements obtained at the boundaries of the furnace and make their decisions on the basis of heuristic rules and results from mathematical models. It is particularly difficult to understand the distribution of the burden materials because of the complex behavior of the particulate materials during charging. The aim of this doctoral thesis is to clarify some aspects of burden distribution and to develop tools that can aid the decision-making process in the control of the burden and gas distribution in the blast furnace. A relatively simple mathematical model was created for simulation of the distribution of the burden material with a bell-less top charging system. The model developed is fast and it can therefore be used by the operators to gain understanding of the formation of layers for different charging programs. The results were verified by findings from charging experiments using a small-scale charging rig at the laboratory. A basic gas flow model was developed which utilized the results of the burden distribution model to estimate the gas permeability of the upper part of the blast furnace. This combined formulation for gas and burden distribution made it possible to implement a search for the best combination of charging parameters to achieve a target gas temperature distribution. As this mathematical task is discontinuous and non-differentiable, a genetic algorithm was applied to solve the optimization problem. It was demonstrated that the method was able to evolve optimal charging programs that fulfilled the target conditions. Even though the burden distribution model provides information about the layer structure, it neglects some effects which influence the results, such as mixed layer formation and coke collapse. A more accurate numerical method for studying particle mechanics, the Discrete Element Method (DEM), was used to study some aspects of the charging process more closely. Model charging programs were simulated using DEM and compared with the results from small-scale experiments. The mixed layer was defined and the voidage of mixed layers was estimated. The mixed layer was found to have about 12% less voidage than layers of the individual burden components. Finally, a model for predicting the extent of coke collapse when heavier pellets are charged over a layer of lighter coke particles was formulated based on slope stability theory, and was used to update the coke layer distribution after charging in the mathematical model. In designing this revision, results from DEM simulations and charging experiments for some charging programs were used. The findings from the coke collapse analysis can be used to design charging programs with more stable coke layers.

DIRECT NUMERICAL SIMULATION OF INCOMPRESSIBLE MULTIPHASE FLOW WITH PHASE CHANGE

Phase change problems arise in many practical applications such as air-conditioning and refrigeration, thermal energy storage systems and thermal management of electronic devices. The physical phenomenon in such applications are complex and are often difficult to be studied in detail with the help of only experimental techniques. The efforts to improve computational techniques for analyzing two-phase flow problems with phase change are therefore gaining momentum. The development of numerical methods for multiphase flow has been motivated generally by the need to account more accurately for (a) large topological changes such as phase breakup and merging, (b) sharp representation of the interface and its discontinuous properties and (c) accurate and mass conserving motion of the interface. In addition to these considerations, numerical simulation of multiphase flow with phase change introduces additional challenges related to discontinuities in the velocity and the temperature fields. Moreover, the velocity field is no longer divergence free. For phase change problems, the focus of developmental efforts has thus been on numerically attaining a proper conservation of energy across the interface in addition to the accurate treatment of fluxes of mass and momentum conservation as well as the associated interface advection. Among the initial efforts related to the simulation of bubble growth in film boiling applications the work in \cite{Welch1995} was based on the interface tracking method using a moving unstructured mesh. That study considered moderate interfacial deformations. A similar problem was subsequently studied using moving, boundary fitted grids \cite{Son1997}, again for regimes of relatively small topological changes. A hybrid interface tracking method with a moving interface grid overlapping a static Eulerian grid was developed \cite{Juric1998} for the computation of a range of phase change problems including, three-dimensional film boiling \cite{esmaeeli2004computations}, multimode two-dimensional pool boiling \cite{Esmaeeli2004} and film boiling on horizontal cylinders \cite{Esmaeeli2004a}. The handling of interface merging and pinch off however remains a challenge with methods that explicitly track the interface. As large topological changes are crucial for phase change problems, attention has turned in recent years to front capturing methods utilizing implicit interfaces that are more effective in treating complex interface deformations. The VOF (Volume of Fluid) method was adopted in \cite{Welch2000} to simulate the one-dimensional Stefan problem and the two-dimensional film boiling problem. The approach employed a specific model for mass transfer across the interface involving a mass source term within cells containing the interface. This VOF based approach was further coupled with the level set method in \cite{Son1998}, employing a smeared-out Heaviside function to avoid the numerical instability related to the source term. The coupled level set, volume of fluid method and the diffused interface approach was used for film boiling with water and R134a at the near critical pressure condition \cite{Tomar2005}. The effect of superheat and saturation pressure on the frequency of bubble formation were analyzed with this approach. The work in \cite{Gibou2007} used the ghost fluid and the level set methods for phase change simulations. A similar approach was adopted in \cite{Son2008} to study various boiling problems including three-dimensional film boiling on a horizontal cylinder, nucleate boiling in microcavity \cite{lee2010numerical} and flow boiling in a finned microchannel \cite{lee2012direct}. The work in \cite{tanguy2007level} also used the ghost fluid method and proposed an improved algorithm based on enforcing continuity and divergence-free condition for the extended velocity field. The work in \cite{sato2013sharp} employed a multiphase model based on volume fraction with interface sharpening scheme and derived a phase change model based on local interface area and mass flux. Among the front capturing methods, sharp interface methods have been found to be particularly effective both for implementing sharp jumps and for resolving the interfacial velocity field. However, sharp velocity jumps render the solution susceptible to erroneous oscillations in pressure and also lead to spurious interface velocities. To implement phase change, the work in \cite{Hardt2008} employed point mass source terms derived from a physical basis for the evaporating mass flux. To avoid numerical instability, the authors smeared the mass source by solving a pseudo time-step diffusion equation. This measure however led to mass conservation issues due to non-symmetric integration over the distributed mass source region. The problem of spurious pressure oscillations related to point mass sources was also investigated by \cite{Schlottke2008}. Although their method is based on the VOF, the large pressure peaks associated with sharp mass source was observed to be similar to that for the interface tracking method. Such spurious fluctuation in pressure are essentially undesirable because the effect is globally transmitted in incompressible flow. Hence, the pressure field formation due to phase change need to be implemented with greater accuracy than is reported in current literature. The accuracy of interface advection in the presence of interfacial mass flux (mass flux conservation) has been discussed in \cite{tanguy2007level,tanguy2014benchmarks}. The authors found that the method of extending one phase velocity to entire domain suggested by Nguyen et al. in \cite{nguyen2001boundary} suffers from a lack of mass flux conservation when the density difference is high. To improve the solution, the authors impose a divergence-free condition for the extended velocity field by solving a constant coefficient Poisson equation. The approach has shown good results with enclosed bubble or droplet but is not general for more complex flow and requires additional solution of the linear system of equations. In current thesis, an improved approach that addresses both the numerical oscillation of pressure and the spurious interface velocity field is presented by featuring (i) continuous velocity and density fields within a thin interfacial region and (ii) temporal velocity correction steps to avoid unphysical pressure source term. Also I propose a general (iii) mass flux projection correction for improved mass flux conservation. The pressure and the temperature gradient jump condition are treated sharply. A series of one-dimensional and two-dimensional problems are solved to verify the performance of the new algorithm. Two-dimensional and cylindrical film boiling problems are also demonstrated and show good qualitative agreement with the experimental observations and heat transfer correlations. Finally, a study on Taylor bubble flow with heat transfer and phase change in a small vertical tube in axisymmetric coordinates is carried out using the new multiphase, phase change method.

Mode locking in a periodically forced "ghostbursting" neuron model

We study a minimal integrate-and-fire based model of a "ghostbursting" neuron under periodic stimulation. These neurons are involved in sensory processing in weakly electric fish. There exist regions in parameter space in which the model neuron is mode-locked to the stimulation. We analyse this locked behavior and examine the bifurcations that define the boundaries of these regions. Due to the discontinuous nature of the flow, some of these bifurcations are nonsmooth. This exact analysis is in excellent agreement with numerical simulations, and can be used to understand the response of such a model neuron to biologically realistic input.

Symmetric Interior Penalty DG Methods for the Compressible Navier-Stokes Equations I: Method Formulation

In this article we consider the development of discontinuous Galerkin finite element methods for the numerical approximation of the compressible Navier-Stokes equations. For the discretization of the leading order terms, we propose employing the generalization of the symmetric version of the interior penalty method, originally developed for the numerical approximation of linear self-adjoint second-order elliptic partial differential equations. In order to solve the resulting system of nonlinear equations, we exploit a (damped) Newton-GMRES algorithm. Numerical experiments demonstrating the practical performance of the proposed discontinuous Galerkin method with higher-order polynomials are presented.

Symmetric Interior Penalty DG Methods for the Compressible Navier-Stokes Equations II: Goal--Oriented A Posteriori Error Estimation

In this article we consider the application of the generalization of the symmetric version of the interior penalty discontinuous Galerkin finite element method to the numerical approximation of the compressible Navier--Stokes equations. In particular, we consider the a posteriori error analysis and adaptive mesh design for the underlying discretization method. Indeed, by employing a duality argument (weighted) Type I a posteriori bounds are derived for the estimation of the error measured in terms of general target functionals of the solution; these error estimates involve the product of the finite element residuals with local weighting terms involving the solution of a certain dual problem that must be numerically approximated. This general approach leads to the design of economical finite element meshes specifically tailored to the computation of the target functional of interest, as well as providing efficient error estimation. Numerical experiments demonstrating the performance of the proposed approach will be presented.

Efeito da adição de óleo essencial de Origanum vulgar e Ocimum gratissimum L. no perfil lipídico da gordura de palma usada em fritura de batata tipo chips

The objective of this study was to determine the antioxidant effect of essential oregano and alfavaca oil on the fatty acid profile of palm oil, used in industrial potato chips processing, aiming to reduce the oxidative state of palm oil. Essential oregano oil was obtained from industrial residues and commercial essential oregano oil was also acquired. The antioxidant activity of Oregano’s essential oil was taken by DPPH method. The DPPH analysis of the essential oil of oregano residue resulted in an IC50 of 797.04 mg.mL-1 and the essential oil of commercial oregano was 424.25 mg.mL-1. Regarding the content of total phenols, the essential oil of commercial oregano showed 0.167 ± 0.058 ug EAG.g-1. Based on these results, concentrations of 50, 100 e 150ug.g-1 of commercial oregano essential oil was added to palm oil and the fatty acid profile was determined by gas cromatography. Analysis were done with palm oil without being used in frying processes and without added essential oil, as well as with the different essential oil concentrations submitted at three frying processes at one single day. In the second part of the project, the effect of oreganos’s comercial essential oil compared to alfavacão essential oil, at the concentration of 100ug.g-1 in palm oil, and submitted to three frying processes during eleven cycles, was studied. The lipid profile was similar to that described in the literature, which an increase in the number of frying times caused a polyunsaturated fatty acids decrease and, therefore, a proportional increase in saturated fatty acids. It was noted an increase in the amounts of total saturated fatty acids from 43.36% (control) to 43.60% (palm oil with essential oil after 11 frying cycles at the concentration of 100ug.g-1). This fact proves that during the frying process, there is an increase in the rate of formation of saturated fatty acids. However, the addition of oregano essential oil did not provide significant change in the fatty acids of palm oil used in frying process of potato chips. The addition of oregano essential oil in a concentration of 100 ug./mL-1 until the third frying cycle showed a reduction effect of trans fatty acid formation. Although, during 11 frying cycles it was not noticed the essential oil effect under trans fatty acid formation. It can be suggested that this factor may be correlated to the frying time, which may not have been sufficient for significant formation of saturated and trans compounds.

Millennial-scale fluctuations of the European Ice Sheet at the end of the last glacial, and their potential impact on global climate

Reconstructing Northern Hemisphere ice-sheet oscillations and meltwater routing to the ocean is important to better understand the mechanisms behind abrupt climate changes. To date, research efforts have mainly focused on the North American (Laurentide) ice-sheets (LIS), leaving the potential role of the European Ice Sheet (EIS), and of the Scandinavian ice-sheet (SIS) in particular, largely unexplored. Using neodymium isotopes in detrital sediments deposited off the Channel River, we provide a continuous and well-dated record for the evolution of the EIS southern margin through the end of the last glacial period and during the deglaciation. Our results reveal that the evolution of EIS margins was accompanied with substantial ice recession (especially of the SIS) and simultaneous release of meltwater to the North Atlantic. These events occurred both in the course of the EIS to its LGM position (i.e., during Heinrich Stadial –HS– 3 and HS2; ∼31–29 ka and ∼26–23 ka, respectively) and during the deglaciation (i.e., at ∼22 ka, ∼20–19 ka and from 18.2 ± 0.2 to 16.7 ± 0.2 ka that corresponds to the first part of HS1). The deglaciation was discontinuous in character, and similar in timing to that of the southern LIS margin, with moderate ice-sheet retreat (from 22.5 ± 0.2 ka in the Baltic lowlands) as soon as the northern summer insolation increase (from ∼23 ka) and an acceleration of the margin retreat thereafter (from ∼20 ka). Importantly, our results show that EIS retreat events and release of meltwater to the North Atlantic during the deglaciation coincide with AMOC destabilisation and interhemispheric climate changes. They thus suggest that the EIS, together with the LIS, could have played a critical role in the climatic reorganization that accompanied the last deglaciation. Finally, our data suggest that meltwater discharges to the North Atlantic produced by large-scale recession of continental parts of Northern Hemisphere ice sheets during HS, could have been a possible source for the oceanic perturbations (i.e., AMOC shutdown) responsible for the marine-based ice stream purge cycle, or so-called HE's, that punctuate the last glacial period.

Ramón Gómez de la Serna y Arqueles Vela: la novela-esponja

[es] Las «novelas de la nebulosa» de Ramón Gómez de la Serna, la narrativa estridentista de Arqueles Vela y la prosa de vanguardia en general se inscriben en un contexto en el que el individuo establece una relación caótica con la realidad. Este estudio comparativo de las novelas ¡Rebeca! (1937) y La Señorita Etcétera (1922), de Gómez de la Serna y Vela, respectivamente, muestra que ambas obras comparten una serie de rasgos: la combinación de recursos provenientes de la tradición y la modernidad, la fragmentación de la anécdota, la búsqueda de una mujer ideal (múltiple y discontinua), la ambigüedad y la metaficción. [en] Ramón Gómez de la Serna’s «novelas de la nebulosa», Arqueles Vela’s stridentist narrative and avant-gard prose generally arise in a context in which the individual establishes a chaotic relationship with reality. This comparative study of their respective novels ¡Rebeca! (1937) and La Señorita Etcétera (1922) shows that both works share some common features: the combination of resources from tradition and modernity, the dissolution of the story, the search for an ideal woman (multiple and discontinuous), ambiguity and metafiction.

Organizational responses to technological discontinuities: the case of the American College of Radiology (ACR)

A long history of organizational research has shown that organizations are affected significantly by changes in technology. Scholars have given particular attention to the effects of so-called disruptive or discontinuous technological changes. Studies have repeatedly shown that established, incumbent organizations tend to suffer deep performance declines (and even complete demise) in the face of such changes, and researchers have devoted much attention to identifying the organizational conditions and processes that are responsible for this persistent and widespread pattern of adaptation failure. This dissertation, which examines the response of the American College of Radiology (ACR) to the emergence of nuclear magnetic resonance imaging technology (NMR), aims to contribute to this well-established research tradition in three distinct and important ways. First, it focuses on a fundamentally different type of organization, a professional association, rather than the technology producers examined in most prior research. Although technologies are well known to be embedded in “communities” that include technology producers, suppliers, customers, governmental entities, professional societies, and other entities, most prior research has focused on the responses and ultimate fate of producers alone. Little if any research has explored the responses of professional organizations in particular. Second, the study employs a sophisticated process methodology that identifies the individual events that make up the organization’s response to technological change, as well as the overall sequence through which these events unfold. This process approach contrasts sharply with the variance models used in most previous studies and offers the promise of developing knowledge about how adaptation ultimately unfolds (or fails to). Finally, the project also contributes significantly through its exploration of an apparently successful case of adaptation to technological change. Though nuclear magnetic resonance imaging posed a serious threat to the ACR and its members, this threat appears to have been successfully managed and overcome. Although the unique nature of the organization and the technology under study place some important limits on the generalizablity of this research, its findings nonetheless provide some important basic insights about the process through which social organizations can successfully adapt to discontinuous technological changes. These insights, which may also be of substantial relevance to technology producer organizations, will also be elaborated.

Desenvolvimento e caracterização de filmes a base de isolado protéico de resíduos de corvina (micropogonias furnieri) e óleo de palma

Nas últimas duas décadas, o descarte e o acúmulo de embalagens não biodegradáveis têm agravado os problemas ambientais. Uma das soluções encontradas, particularmente na área de embalagens de alimentos, é o desenvolvimento de filmes a partir de polímeros que possam substituir os materiais sintéticos. Fontes alternativas de proteína, como os resíduos de pescados, tornam-se importante, pois estes representam de 60 a 70% da matéria-prima e são descartados pelas indústrias de filetagem contribuindo com os danos ao meio ambiente. As propriedades funcionais dos filmes biodegradáveis são resultantes das características das macromoléculas utilizadas, das interações entre os constituintes envolvidos na formulação (macromolécula, solvente, plastificante e outros aditivos), dos parâmetros de fabricação (temperatura, tipo de solvente, pH, entre outras), do processo de dispersão da solução filmogênica (pulverização, espalhamento, etc.) e das condições de secagem. Um problema limitante no uso de filmes biodegradáveis a base de proteínas de pescado é a sua susceptibilidade à umidade, devido à hidrofilicidade dos aminoácidos das moléculas de proteína. O objetivo geral do trabalho foi desenvolver e caracterizar filmes a base de isolado proteico de resídeos de corvina (IPC) e óleo de palma (OP). O desenvolvimento dos filmes foi estudado em duas etapas. Neste estudo utilizou-se resíduos de corvina (Micropogonias furnieri) para a obtenção do isolado protéico, glicerol como plastificante e óleo de palma para conferir hidrofobicidade ao filme. Na primeira etapa, o objetivo foi investigar o efeito das concentrações de IPC, de glicerol e do pH sobre as propriedades dos filmes de proteína de resíduos de corvina (Micropogonias furnieri). Os filmes foram avaliados quanto aos parâmetros de cor, opacidade, propriedades mecânicas, espessura, solubilidade em água, permeabilidade de vapor de água (PVA) e propriedades morfológicas. Como resultado foi observado que a opacidade e a luminosidade dos filmes não foram afetados pelas variáveis do processo. Os filmes de IPC ficaram amarelados e opacos. Apresentaramse mais claros quando elaborados com baixas concentrações de IPC e altas concentrações de glicerol nas soluções filmogênicas. A menor solubilidade em água ocorreu nos filmes com pH baixo e menores concentrações de glicerol. Com relação as propriedades mecânicas, os filmes apresentaram alta elongação e sua resistência à tração aumentou quando utilizadas maiores concentrações de IPC, menores concentrações de glicerol e pHs mais baixos.Os filmes apresentaram superficies ásperas e irregulares. Na segunda etapa foram elaborados filmes biodegradáveis de IPC contendo diferentes concentrações de óleo de palma (OP) (10 e 20 g de OP /100g de IPC) e suas propriedades de barreira, mecânicas, físico-químicas, térmicas e morfológicas foram estudadas. A adição de OP aumentou as espessuras dos filmes com 2 e 4% de IPC, no entanto a solubilidade não foi afetada pela adição do OP. Os filmes com 3 e 4% de IPC ficaram menos permeáveis a água quando incorporado 20% de OP nos mesmos. A opacidade dos filmes aumentou com a adição do OP. A incorporação do OP nos filmes resultou em uma diminuição da resistência à tração e no aumento da elongação dos filmes. Nos filmes com 2% de IPC o aumento na elongação foi significativo apenas quando adicionado 20% de OP. O aparecimento de apenas uma temperatura de fusão nos filmes sugeriu uma homogeneidade dos mesmos. A decomposição térmica dos filmes iniciou em torno de 120 -173ºC. Os filmes apresentaram uma superfície descontínua.

Selected Violin Concertos: In Search of a Missing Link

My dissertation presented seven violin concertos in three recital programs. Three of these concertos are acknowledged masterpieces performed in established concert venues throughout the world. They are the concertos of Mozart, Beethoven and Tchaikovsky. The other four are less standard and are composed by Viotti, Kreutzer, Rode and Spohr. These less standard concertos were popular during their time yet they seem not to have stood the test of time. A curriculum devoted exclusively to the standard concertos creates problems for the young violinist. The Mozart violin concertos are often the first standard concertos that the young violin student encounters. They are considered to be the least technically demanding of the standard concertos. The next most advanced standard concertos that the student will usually encounter are Bruch’s G minor concerto, Wieniawski’s D minor concerto and Barber’s concerto. The trouble is that the work on Mozart concertos does not adequately prepare a student for the next most advanced standard concerto. There is a discontinuous leap in the progression of technical difficulty between the Mozart concertos and the next most advanced concertos. Likewise the standard concerto repertoire provides no smooth historical or stylistic progression between the Mozart concertos and the next most advanced concertos. If the young violinist is limited to the standard repertoire then she has no smooth progression either technical, historical or stylistic. I seek to demonstrate that, by adding concertos of Spohr, Viotti, Kreutzer, and Rode to the standard violin curriculum, one could remedy this problem. The first and third recitals were performed in the Gildenhorn Recital Hall and the second recital in the School of Music’s Smith Lecture Hall, both at the University of Maryland. All three recitals can be found in the Digital Repository at the University of Maryland (DRUM).