Direct-on-line axial flux permanent magnet synchronous generator static and dynamic performance

In distributed energy production, permanent magnet synchronous generators (PMSG) are often connected to the grid via frequency converters, such as voltage source line converters. The price of the converter may constitute a large part of the costs of a generating set. Some of the permanent magnet synchronous generators with converters and traditional separately excited synchronous generators couldbe replaced by direct-on-line (DOL) non-controlled PMSGs. Small directly networkconnected generators are likely to have large markets in the area of distributed electric energy generation. Typical prime movers could be windmills, watermills and internal combustion engines. DOL PMSGs could also be applied in island networks, such as ships and oil platforms. Also various back-up power generating systems could be carried out with DOL PMSGs. The benefits would be a lower priceof the generating set and the robustness and easy use of the system. The performance of DOL PMSGs is analyzed. The electricity distribution companies have regulations that constrain the design of the generators being connected to the grid. The general guidelines and recommendations are applied in the analysis. By analyzing the results produced by the simulation model for the permanent magnet machine, the guidelines for efficient damper winding parameters for DOL PMSGs are presented. The simulation model is used to simulate grid connections and load transients. The damper winding parameters are calculated by the finite element method (FEM) and determined from experimental measurements. Three-dimensional finite element analysis (3D FEA) is carried out. The results from the simulation model and 3D FEA are compared with practical measurements from two prototype axial flux permanent magnet generators provided with damper windings. The dimensioning of the damper winding parameters is case specific. The damper winding should be dimensioned based on the moment of inertia of the generating set. It is shown that the damper winding has optimal values to reach synchronous operation in the shortest period of time after transient operation. With optimal dimensioning, interferenceon the grid is minimized.

Marketing de banana: preferências do consumidor quanto aos atributos de qualidade dos frutos

O Brasil produz aproximadamente seis milhões de toneladas por ano de banana (Musa spp.), com consumo médio da ordem de 35 kg/ habitante / ano. A aceitação da banana deve-se, principalmente, a seus aspectos sensoriais, valor nutricional e conveniência. A identificação das necessidades e desejos dos clientes consiste em uma atividade crítica do marketing. O objetivo deste trabalho foi o de pesquisar as preferências do consumidor de um mercado local (município de Cruz das Almas - Estado da Bahia) considerando os atributos de qualidade dos frutos frescos de banana madura. A metodologia utilizada foi a da pesquisa descritiva por método estatístico. Os dados foram coletados por questionário, na forma de entrevista pessoal com 400 pessoas. Os atributos de qualidade (variáveis) questionados e avaliados foram relacionados com a aparência, cor, textura, aroma, sabor e vida útil esperada dos frutos de banana. De acordo com a preferência dos consumidores entrevistados, o fruto de banana maduro ideal deve apresentar características como: penca contendo 10 a 12 dedos (frutos), dedos de tamanho médio ou grande, diâmetro médio, quina presente, ausência de pintas pretas na casca, cor da polpa amarelo-clara ou média, textura firme, aroma e sabor de intensidade média, mediamente doce e vida útil de 7 a 10 dias em condição ambiente. O sabor, vida útil e aparência dos frutos de banana são considerados os mais importantes atributos na escolha ou compra da banana, segundo os consumidores entrevistados.

Direct torque control of permanent magnet synchronous machines - analysis and implementation

Thedirect torque control (DTC) has become an accepted vector control method besidethe current vector control. The DTC was first applied to asynchronous machines,and has later been applied also to synchronous machines. This thesis analyses the application of the DTC to permanent magnet synchronous machines (PMSM). In order to take the full advantage of the DTC, the PMSM has to be properly dimensioned. Therefore the effect of the motor parameters is analysed taking the control principle into account. Based on the analysis, a parameter selection procedure is presented. The analysis and the selection procedure utilize nonlinear optimization methods. The key element of a direct torque controlled drive is the estimation of the stator flux linkage. Different estimation methods - a combination of current and voltage models and improved integration methods - are analysed. The effect of an incorrect measured rotor angle in the current model is analysed andan error detection and compensation method is presented. The dynamic performance of an earlier presented sensorless flux estimation method is made better by improving the dynamic performance of the low-pass filter used and by adapting the correction of the flux linkage to torque changes. A method for the estimation ofthe initial angle of the rotor is presented. The method is based on measuring the inductance of the machine in several directions and fitting the measurements into a model. The model is nonlinear with respect to the rotor angle and therefore a nonlinear least squares optimization method is needed in the procedure. A commonly used current vector control scheme is the minimum current control. In the DTC the stator flux linkage reference is usually kept constant. Achieving the minimum current requires the control of the reference. An on-line method to perform the minimization of the current by controlling the stator flux linkage reference is presented. Also, the control of the reference above the base speed is considered. A new estimation flux linkage is introduced for the estimation of the parameters of the machine model. In order to utilize the flux linkage estimates in off-line parameter estimation, the integration methods are improved. An adaptive correction is used in the same way as in the estimation of the controller stator flux linkage. The presented parameter estimation methods are then used in aself-commissioning scheme. The proposed methods are tested with a laboratory drive, which consists of a commercial inverter hardware with a modified software and several prototype PMSMs.

Instrumentos promocionales en el marketing público: una aplicación empírica

El presente trabajo trata de determinar que elementos son valorados por el sector privado a nivel global de cara a dar soporte a una determinada acción de promoción por parte de una entidad pública. Este estudio ha sido complementado con un análisis sectorial detallado para caracterizar los sectores que definen el tejido económico y comprobar si cada uno de ellos requiere un trato individualizado. En el desarrollo del estudio se ha aplicado análisis univariante y bivariante, y contraste χ 2, llevado a cabo sobre una muestra representativa de las empresas seleccionadas sectorialmente y que se hallan ubicadas en la zona de influencia de la población de Mollerusa de la provincia de Lleida. El origen de nuestro trabajo se encuentra en un proyecto de investigación que realizó nuestro Departamento en convenio con el Patronat de Fires de Mollerussa (Patronato de Ferias de Mollerusa).

Personality and job stress: a comparison of direct effects on parenting

The impact of personality and job characteristics on parental rearing styles was compared in 353 employees. Hypotheses concerning the relationships between personality and job variables were formulated in accordance with findings in past research and the Belsky’s model (1984). Structural equation nested models showed that Aggression-hostility, Sociability and job Demand were predictive of Rejection and Emotional Warmth parenting styles, providing support for some of the hypothesized relationships. The findings suggest a well-balanced association of personality variables with both parenting styles: Aggression-Hostility was positively related to Rejection and negatively to Emotional Warmth, whereas Sociability was positively related to Emotional Warmth and negatively related to Rejection. Personality dimensions explained a higher amount of variance in observed parenting styles. However, a model that considered both, personality and job dimensions as antecedent variables of parenting was the best representation of observed data, as both systems play a role in the prediction of parenting behavior.

Marketing strategy for a GSM phone service. Target market, St. Petersburg Russia. Case MegaFon

Tämä pro gradu tutkielma esittää markkinointistrategian digitaaliselle matkapuhelinpalvelulle penetroiduttaessa uusille markkinoille. MegaFon on uuden sukupolven mobiilioperaattori, jolla on lukuisia teknlogiaan perustuvia etuisuuksia puolellaan. Markkinointistrategian perusteena asiakkaat on määritelty, paikallistettu ja analysoitu. Tämän lisäksi, palvelun positiointi, hinnoittelu- ja jakelukanavavaihtoehdot on myöskin analysoitu ja määritelty. Menestystekijöihin liittyvät kysymykset, myynnin jälkeiseen toimintaan liittyvät asiat on myös tutkittu. Teoreettiset aspektit liittyvät pääsääntöisesti uuden palvelun ja palveluiden lanseeramiseen (palvelu, palvelun elinkaariajattelu), niiden markkinointistrategioihin lanseerausvaiheessa ja markkinointikanavien päättämiseen. Tutkimuksessa on selitetty MegaFonin ennustamis- ja lähestymistavat, joilla on valotettu todellista markkinatilannetta. Tämän tutkielman informaatio on kerätty useista lähteistä, kuten: yleistä aiheeseen liittyvää kirjallisuutta, sisäisiä raportteja ja Megafonin materiaalia, yhteistyökumppaneiden aineistoa, Internettia ja muuta saatavilla olevaa materiaalia. Tuloksena on määritelty päätöksenteon avainkohdat ja osaltaan perinteiset lähestymistavat on kyseenalaistettu.

Clinical effectiveness of direct anterior restorations-A meta-analysis.

OBJECTIVES: This is the first meta-analysis on the efficacy of composite resin restorations in anterior teeth. The objective of the present meta-analysis was to verify whether specific material classes, tooth conditioning methods and operational procedures influence the result for Class III and Class IV restorations. MATERIAL AND METHODS: The database SCOPUS and PubMed were searched for clinical trials on anterior resin composites without restricting the search to the year of publication. The inclusion criteria were: (1) prospective clinical trial with at least 2 years of observation; (2) minimal number of restorations at last recall=20; (3) report on drop-out rate; (4) report of operative technique and materials used in the trial, and (5) utilization of Ryge or modified Ryge evaluation criteria. For the statistical analysis, a linear mixed model was used with random effects to account for the heterogeneity between the studies. p-Values smaller than 0.05 were considered to be significant. RESULTS: Of the 84 clinical trials, 21 studies met the inclusion criteria, 14 of them for Class III restorations, 6 for Class IV restorations and 1 for closure of diastemata; the latter was included in the Class IV group. Twelve of the 21 studies started before 1991 and 18 before 2001. The estimated median overall success rate (without replacement) after 10 years for Class III composite resin restorations was 95% and for Class IV restorations 90%. The main reason for the replacement of Class IV restorations was bulk fractures, which occurred significantly more frequently with microfilled composites than with hybrid and macrofilled composites. Caries adjacent to restorations was infrequent in most studies and accounted only for about 2.5% of all replaced restorations after 10 years irrespective of the cavity class. Class III restorations with glass ionomer derivates suffered significantly more loss of anatomical form than did fillings with other types of material. When the enamel was acid-etched and no bonding agent was applied, significantly more restorations showed marginal staining and detectable margins compared to enamel etching with enamel bonding or the total etch technique; fillings with self-etching systems were in between of these two outcome variables. Bevelling of the enamel was associated with a significantly reduced deterioration of the anatomical form compared to no bevelling but not with less marginal staining or less detectable margins. The type of isolation (absolute/relative) had a statistically significant influence on marginal caries which, however, might be a random finding.