Physical, chemical and microbiological properties of a Dystrophic Yellow Latosol using manipueira

The study aimed to evaluate chemical, microbiological and hydro-physical changes of a Dystrophic Yellow Latosol, receiver of different levels of manipueira (cassava wastewater) application, in the cultivation of 'Terra Maranhão' banana. The experimental design was a randomized block with three replications in a factorial scheme 3 x 4, in which it was considered three soil depths and four levels of manipueira. It was evaluated the weighted mean diameter of the aggregate, the percentage of aggregation at different periods, soil density, particle density, porosity and soil saturated hydraulic conductivity, in addition to pH of P (mg dm -3), K (mg dm-3), Ca (cmolc dm-3), Mg (cmolc dm-3), Ca+Mg (cmolc dm-3), Al (cmolc dm-3), Na (cmolc dm -3), H+Al (cmolc dm-3), CEC (cmolc dm-3), V%, OM (g kg-1), soil microbial biomass (Ug Cg-1 dry soil), acid phosphatase (Ug PNP g-1 h-1). The use of manipueira influenced some physical characteristic of the soil, but it was not possible to specify the effect of increasing application dosage. Therefore, the application did not affect the biological indicators assessed in the soil or its pH. The use of manipueira as a fertilizer in the doses used in this study showed low increase of K, P, H+Al and Al in the soil and a good increase of Mg, Ca and Ca+Mg, Na, CEC and V%.

Tabular cusum control charts of chemical variables applied to the control of surface water quality

The aim of this study was to evaluate the application possibility of tabular CUSUM control charts in the quality control of chemical variables in surface water. It was performed bibliographic and field research to collect water samples from 2003 to 2009, totaling 30 samples, some monthly and others semi-annual in order to observe the variables that regulate water quality. It was found that these charts may be applied to control the quality of river water; showing to be effective in the perception of changes during the process, especially for small samples (n=1) which there is no repetition as in this research. It was also concluded that the Mandurim River does not presents significant levels of pollution.

Management zones definition using soil chemical and physical attributes in a soybean area

Several equipments and methodologies have been developed to make available precision agriculture, especially considering the high cost of its implantation and sampling. An interesting possibility is to define management zones aim at dividing producing areas in smaller management zones that could be treated differently, serving as a source of recommendation and analysis. Thus, this trial used physical and chemical properties of soil and yield aiming at the generation of management zones in order to identify whether they can be used as recommendation and analysis. Management zones were generated by the Fuzzy C-Means algorithm and their evaluation was performed by calculating the reduction of variance and performing means tests. The division of the area into two management zones was considered appropriate for the present distinct averages of most soil properties and yield. The used methodology allowed the generation of management zones that can serve as source of recommendation and soil analysis; despite the relative efficiency has shown a reduced variance for all attributes in divisions in the three sub-regions, the ANOVA did not show significative differences among the management zones.

Physical-chemical characterization and wet milling yield of four maize hybrids

The influence of physical-chemical characteristics of maize grains and lactic acid concentrations on byproduct yields, generated by conventional wet milling, was studied during steeping, for four maize hybrids and two lactic acid concentrations (0.55 and 1.00%). For physical-chemical characterization, grain dimensions (length, thickness, and width) were determined, as well as mass of 100 grains, percentage of floating grains, volumetric mass, and centesimal composition. Statistical differences were found for percentage of floating grains (2.33 to 24.67%), volumetric mass (0.814 to 0.850 kg.L-1), mass of 100 grains (0.033 to 0.037 kg), water content (11.86 to 12.20%), proteins (8.21 to 9.06%), lipids (3.00 to 4.77%), and ashes (1.07 to 1.26%). There were no relationships of wet milling yields with maize appearance and physical-chemical characteristics. The addition of 1.00% lactic acid did not statistically improve byproduct yields; however, it favored separation of the grain components.

Chemical attributes of soil and dry mass accumulation of maize fertilized with cassava wastewater

The aim of this study was to evaluate chemical attributes alterations of a clay-loam textured soil and dry mass accumulation of maize submitted to application of cassava wastewater doses in three assessment periods. The experiment was conducted under greenhouse using a completely randomized experimental design in a factorial 5 × 3, with four replicates. The analyzed factors of research were doses of cassava wastewater (0; 12.6; 25.2; 50.4; 75.6 m3 ha-1) andassessment periods (20, 40 and 52 days after germination). The following parameters were determined: electric conductivity of soil saturation extract, pH in water, content of available P, content of exchangeable K+, Ca2+, Mg2+ and Na+of soil, dry mass of leaves and stem. The application of cassava wastewater on soil enables increase of pH, electric conductivity of saturation extract, contents of available P, contents of exchangeable K+ and Na+ and dry mass of leaves and stem. However, only pH and content of exchangeable K+ of soil, the electric conductivity of saturation extract and dry mass of leaves and stem are influenced by assessment period.

Spatial influence of physical and chemical parameters on management zone definition in apple orchards

ABSTRACT Precision agriculture adoption in Brazilian apple orchards is still incipient. This study aimed at evaluating the spatial variability of certain soil properties as soil density, soil penetration resistance, electrical conductivity, yield, and fruit quality in an apple orchard through digital mapping, as well as assessing the correlation between these factors by means of geostatistics, establishing management zones. Forty representative points were set within 2.5 hectares of apple orchard, wherein soil samples were collected and analyzed, besides measurements of fruit quality (Brix degree, size or diameter, pulp firmness and color) to generate an overall index quality. We concluded that the fruit quality indexes, when isolated, did not show strong spatial dependence, unlike the index of fruit quality (FQI), derived from a combination of these parameters, allowing orchard planning according to management zones based on quality.

Biomass fractionation

The objective of this master's thesis was to develop a process to increase the value of residual fungal biomass as an animal feed. The increase in value is achieved by enriching the protein content in the biomass and potentially isolating other valuable fractions for productisation. In the literature part of this thesis the composition of fungal biomass and fungal cell wall and the factors affecting them during cultivation are presented. The possible processing options are also presented and evaluated. The soy protein and single cell protein product manufacturing processes are used as examples due to the lack of fungal biomass fractionation processes found in published literature. The second part of this thesis was performed by making laboratory experiments on the developed process, which consisted of acid hydrolysis with subsequent ethanol extraction. Chitin was precipitated from the acid hydrolysate filtrate. The experiments were conducted with three different hydrolysis temperatures and three different acid concentrations. The optimal hydrolysis conditions were 60 °C with 10 %-vol acid concentration. Optimal conditions in hydrolysis resulted in 30 % increase in protein content in the final biomass. The conceptual process was modelled to scale of 10 000 t/a biomass feed. The mass and energy balances were based on the laboratory experiments. Economic calculations were performed to determine the maximal capital expense while achieving 10 % internal rate of return for the investment. For the basic case the capital expense threshold was 25.8 M€. Four optional cases and parameter sensitivity analysis were performed to determine the effects of changes in the process. The chitin sales had the greatest impact of the individual parameters.

Membraanin modifiointi happo- ja alkoholikäsittelyillä

Tässä diplomityössä tutkittiin alkoholilla ja orgaanisella hapolla tehtävien esikäsittelyiden vaikutusta nanosuodatuskalvon ominaisuuksiin. Työn tarkoituksena oli parantaa nanosuodatuskalvon fraktiointiominaisuuksia sekä kasvattaa monosakkaridien suotautuvuutta. Tarkasteluissa käytetty membraani oli GE Osmonicsin valmistamaa Desal-5 DL nanosuodatuskalvoa, jota modifioitiin erilaisilla maitohappo- ja isopropanoliesikäsittelyillä. Suodatukset tehtiin kahdella erilaisella laboratoriomittakaavan levysuotimella käyttäen malliaineina väkevää sokeriliuosta sekä laimeampaa sokeri-suola-liuosta. Happo- ja alkoholiesikäsiteltyjen kalvojen vuo- ja retentioarvoja verrattiin referensseinä käytettyjen vesiliotettujen kalvojen vastaaviin arvoihin. Puhtaat esikäsitellyt kalvot analysoitiin myös tarkemmin kalvoissa tapahtuneiden muutosten ymmärtämiseksi. Suodatusten ja analyysitulosten perusteella sekä alkoholi- että happoesikäsittelyt paransivat nanosuodatuskalvon ominaisuuksia parantaen sokerivuota, heikentämättä kuitenkaan kalvon fraktiointikykyä eri moolimassan omaavien sokereiden suhteen. Hapolla saavutettiin hieman alkoholikäsittelyä suotuisammat muutokset, mutta molemmilla käsittelyillä haluttujen komponenttien retentio monesti jopa parani referenssikalvoon verrattuna. Havaitut muutokset kalvoissa olivat pääosin fysikaalisia, mutta erityisesti happokäsittely muutti kalvon rakennetta myös kemiallisesti. Molemmat käsittelyt lisäsivät myös tarkasteltavan membraanin hydrofiilisuutta.

Self-Assessment Report for International Accreditation - Chemical Engineering

Kemiantekniikan kandidaatin ja diplomi-insinöörin tutkinto-ohjelmien itsearviointiraportissa käsitellään tutkinto-ohjelmien osaamistavoitteita ja niiden saavuttamista. Raportissa käydään läpi myös käytössä olevat resurssit sekä tutkinto-ohjelmiin liittyviä tunnuslukuja. Itsearviointi on toteutettu kansainvälisen akkreditointijärjestön kriteerien mukaisesti (ASIIN ja EUR-ACE).

Combination of catalyst development and chemical reaction engineering : a key aspect to improve the hydrogen peroxide direct synthesis

-

Synthesis, characterization and chemical sensor application of conducting polymers

Polymeric materials that conduct electricity are highly interesting for fundamental studies and beneficial for modern applications in e.g. solar cells, organic field effect transistors (OFETs) as well as in chemical and bio‐sensing. Therefore, it is important to characterize this class of materials with a wide variety of methods. This work summarizes the use of electrochemistry also in combination with spectroscopic methods in synthesis and characterization of electrically conducting polymers and other π‐conjugated systems. The materials studied in this work are intended for organic electronic devices and chemical sensors. Additionally, an important part of the presented work, concerns rational approaches to the development of water‐based inks containing conducting particles. Electrochemical synthesis and electroactivity of conducting polymers can be greatly enhanced in room temperature ionic liquids (RTILs) in comparison to conventional electrolytes. Therefore, poly(para‐phyenylene) (PPP) was electrochemically synthesized in the two representative RTILs: bmimPF6 and bmiTf2N (imidazolium and pyrrolidinium‐based salts, respectively). It was found that the electrochemical synthesis of PPP was significantly enhanced in bmimPF6. Additionally, the results from doping studies of PPP films indicate improved electroactivity in bmimPF6 during oxidation (p‐doping) and in bmiTf2N in the case of reduction (n‐doping). These findings were supported by in situ infrared spectroscopy studies. Conducting poly(benzimidazobenzophenanthroline) (BBL) is a material which can provide relatively high field‐effect mobility of charge carriers in OFET devices. The main disadvantage of this n‐type semiconductor is its limited processability. Therefore in this work BBL was functionalized with poly(ethylene oxide) PEO, varying the length of side chains enabling water dispersions of the studied polymer. It was found that functionalization did not distract the electrochemical activity of the BBL backbone while the processability was improved significantly in comparison to conventional BBL. Another objective was to study highly processable poly(3,4‐ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) water‐based inks for controlled patterning scaled‐down to nearly a nanodomain with the intention to fabricate various chemical sensors. Developed PEDOT:PSS inks greatly improved printing of nanoarrays and with further modification with quaternary ammonium cations enabled fabrication of PEDOT:PSS‐based chemical sensors for lead (II) ions with enhanced adhesion and stability in aqueous environments. This opens new possibilities for development of PEDOT:PSS films that can be used in bio‐related applications. Polycyclic aromatic hydrocarbons (PAHs) are a broad group of π‐conjugated materials consisting of aromatic rings in the range from naphthalene to even hundred rings in one molecule. The research on this type of materials is intriguing, due to their interesting optical properties and resemblance of graphene. The objective was to use electrochemical synthesis to yield relatively large PAHs and fabricate electroactive films that could be used as template material in chemical sensors. Spectroscopic, electrochemical and electrical investigations evidence formation of highly stable films with fast redox response, consisting of molecules with 40 to 60 carbon atoms. Additionally, this approach in synthesis, starting from relatively small PAH molecules was successfully used in chemical sensor for lead (II).

Chromatographic recovery of chemicals from acidic biomass hydrolysates

Lignocellulosic biomasses (e.g., wood and straws) are a potential renewable source for the production of a wide variety of chemicals that could be used to replace those currently produced by petrochemical industry. This would lead to lower greenhouse gas emissions and waste amounts, and to economical savings. There are many possible pathways available for the manufacturing of chemicals from lignocellulosic biomasses. One option is to hydrolyze the cellulose and hemicelluloses of these biomasses into monosaccharides using concentrated sulfuric acid as catalyst. This process is an efficient method for producing monosaccharides which are valuable platforn chemicals. Also other valuable products are formed in the hydrolysis. Unfortunately, the concentrated acid hydrolysis has been deemed unfeasible mainly due to high chemical consumption resulting from the need to remove sulfuric acid from the obtained hydrolysates prior to the downstream processing of the monosaccharides. Traditionally, this has been done by neutralization with lime. This, however, results in high chemical consumption. In addition, the by-products formed in the hydrolysis are not removed and may, thus, hinder the monosaccharide processing. In order to improve the feasibility of the concentrated acid hydrolysis, the chemical consumption should be decreased by recycling of sulfuric acid without neutralization. Furthermore, the monosaccharides and the other products formed in the hydrolysis should be recovered selectively for efficient downstream processing. The selective recovery of the hydrolysis by-products would have additional economical benefits on the process due to their high value. In this work, the use of chromatographic fractionation for the recycling of sulfuric acid and the selective recovery of the main components from the hydrolysates formed in the concentrated acid hydrolysis was investigated. Chromatographic fractionation based on the electrolyte exclusion with gel type strong acid cation exchange resins in acid (H+) form as a stationary phase was studied. A systematic experimental and model-based study regarding the separation task at hand was conducted. The phenomena affecting the separation were determined and their effects elucidated. Mathematical models that take accurately into account these phenomena were derived and used in the simulation of the fractionation process. The main components of the concentrated acid hydrolysates (sulfuric acid, monosaccharides, and acetic acid) were included into this model. Performance of the fractionation process was investigated experimentally and by simulations. Use of different process options was also studied. Sulfuric acid was found to have a significant co-operative effect on the sorption of the other components. This brings about interesting and beneficial effects in the column operations. It is especially beneficial for the separation of sulfuric acid and the monosaccharides. Two different approaches for the modelling of the sorption equilibria were investigated in this work: a simple empirical approach and a thermodynamically consistent approach (the Adsorbed Solution theory). Accurate modelling of the phenomena observed in this work was found to be possible using the simple empirical models. The use of the Adsorbed Solution theory is complicated by the nature of the theory and the complexity of the studied system. In addition to the sorption models, a dynamic column model that takes into account the volume changes of the gel type resins as changing resin bed porosity was also derived. Using the chromatography, all the main components of the hydrolysates can be recovered selectively, and the sulfuric acid consumption of the hydrolysis process can be lowered considerably. Investigation of the performance of the chromatographic fractionation showed that the highest separation efficiency in this separation task is obtained with a gel type resin with a high crosslinking degree (8 wt. %); especially when the hydrolysates contain high amounts of acetic acid. In addition, the concentrated acid hydrolysis should be done with as low sulfuric acid concentration as possible to obtain good separation performance. The column loading and flow rate also have large effects on the performance. In this work, it was demonstrated that when recycling of the fractions obtained in the chromatographic fractionation are recycled to preceding unit operations these unit operations should included in the performance evaluation of the fractionation. When this was done, the separation performance and the feasibility of the concentrated acid hydrolysis process were found to improve considerably. Use of multi-column chromatographic fractionation processes, the Japan Organo process and the Multi-Column Recycling Chromatography process, was also investigated. In the studied case, neither of these processes could compete with the single-column batch process in the productivity. However, due to internal recycling steps, the Multi-Column Recycling Chromatography was found to be superior to the batch process when the product yield and the eluent consumption were taken into account.

Recovery of biomass-derived valuable compounds using chromatographic and membrane separations

Utilization of biomass-based raw materials for the production of chemicals and materials is gaining an increasing interest. Due to the complex nature of biomass, a major challenge in its refining is the development of efficient fractionation and purification processes. Preparative chromatography and membrane filtration are selective, energy-efficient separation techniques which offer a great potential for biorefinery applications. Both of these techniques have been widely studied. On the other hand, only few process concepts that combine the two methods have been presented in the literature. The aim of this thesis was to find the possible synergetic effects provided by combining chromatographic and membrane separations, with a particular interest in biorefinery separation processes. Such knowledge could be used in the development of new, more efficient separation processes for isolating valuable compounds from complex feed solutions that are typical for the biorefinery environment. Separation techniques can be combined in various ways, from simple sequential coupling arrangements to fully-integrated hybrid processes. In this work, different types of combined separation processes as well as conventional chromatographic separation processes were studied for separating small molecules such as sugars and acids from biomass hydrolysates and spent pulping liquors. The combination of chromatographic and membrane separation was found capable of recovering high-purity products from complex solutions. For example, hydroxy acids of black liquor were successfully recovered using a novel multistep process based on ultrafiltration and size-exclusion chromatography. Unlike any other separation process earlier suggested for this challenging separation task, the new process concept does not require acidification pretreatment, and thus it could be more readily integrated into a pulp-mill biorefinery. In addition to the combined separation processes, steady-state recycling chromatography, which has earlier been studied for small-scale separations of high-value compounds only, was found a promising process alternative for biorefinery applications. In comparison to conventional batch chromatography, recycling chromatography provided higher product purity, increased the production rate and reduced the chemical consumption in the separation of monosaccharides from biomass hydrolysates. In addition, a significant further improvement in the process performance was obtained when a membrane filtration unit was integrated with recycling chromatography. In the light of the results of this work, separation processes based on combining membrane and chromatographic separations could be effectively applied for different biorefinery applications. The main challenge remains in the development of inexpensive separation materials which are resistant towards harsh process conditions and fouling.

Wet oxidation of biomass for chemical production

Tämän kandidaatintyön tarkoituksena oli tutkia märkähapetusprosessia jätevesien käsittely-menetelmänä ja mahdollisena menetelmänä kemikaalien tuottamiseksi jätevesistä. Erityishuomio on kiinnitetty paperiteollisuudessa syntyviin jätevesiin. Teoriaosassa käsitellään vesikiertoja paperitehtaassa, paperitehtaalla syntyvän jäteveden ominaisuuksia sekä itse märkähapetusprosessia. Märkähapetusprosessissa perehdytään tavalliseen happea käyttävään märkähapetukseen sekä vetyperoksidia käyttävään menetelmään sekä näissä prosesseissa syntyviin väli- ja lopputuotteisiin. Märkähapetus (WO) on terminen hapetusmenetelmä, jolla voidaan käsitellä jätevesiä, jotka ovat liian konsentroituja biologisiin käsittelyihin tai jotka ovat huonosti biohajoavia. Märkähapetuksen tarkoituksena on parantaa molekulaarisen hapen ja orgaanisen aineen välistä kontaktia, jolloin orgaaninen aines pilkkoutuu muodostaen pääasiassa karboksyylihappoja, aldehydejä, hiilidioksidia ja vettä. Märkähapetuksessa hapettavana kaasuna voidaan käyttää joko puhdasta happea tai ilmaa. Vetyperoksidia käyttävässä märkähapetuksessa (WPO) hapettava kaasu on korvattu nestemäisellä vetyperoksidilla. Kokeellisessa osassa tutkittiin orgaanisen aineksen hapetusta käyttäen Fentonin reagenssia, jolloin katalyyttina reaktiossa toimii rautaionit (Fe2+ ja Fe3+) ja hapettimena vetyperoksidi. Hapetettavana jätevetenä käytettiin paperitehtaan hiomolta saatua kiertovettä, TMP-vettä. Hapetuskokeita tehtiin eri vetyperoksidin annoksilla ja katalyytin määrillä eri lämpötiloissa. Hapetuksen jälkeen näytteistä mitattiin kemiallinen hapenkulutus (COD), orgaanisen hiilen kokonaismäärä (TOC) sekä pH. Lisäksi näytteistä määritettiin nestekromatografilla (HPLC) tyypillisten välituotteiden, kuten oksaalihapon, muurahaishapon ja etikkahapon, määrät. Tehdyissä kokeissa COD-arvoja saatiin pienennettyä 50-88 % siten, että suodatetuissa näytteissä muutos oli suurempi kuin suodattamattomissa näytteissä. Lisäksi TOC-arvot laskivat 28-58 %. Tehdyissä kokeissa saatiin myös tuotettua välituotteina karboksyylihappoja, joista etikkahappoa ja oksaalihappoa tuotettiin suurimmat määrät. Myös muurahaishappoa ja meripihkahappoa saatiin tuotettua.

Improving the competitiveness of electrolytic Zinc process by chemical reaction engineering approach

This doctoral thesis describes the development work performed on the leachand purification sections in the electrolytic zinc plant in Kokkola to increase the efficiency in these two stages, and thus the competitiveness of the plant. Since metallic zinc is a typical bulk product, the improvement of the competitiveness of a plant was mostly an issue of decreasing unit costs. The problems in the leaching were low recovery of valuable metals from raw materials, and that the available technology offered complicated and expensive processes to overcome this problem. In the purification, the main problem was consumption of zinc powder - up to four to six times the stoichiometric demand. This reduced the capacity of the plant as this zinc is re-circulated through the electrolysis, which is the absolute bottleneck in a zinc plant. Low selectivity gave low-grade and low-value precipitates for further processing to metallic copper, cadmium, cobalt and nickel. Knowledge of the underlying chemistry was poor and process interruptions causing losses of zinc production were frequent. Studies on leaching comprised the kinetics of ferrite leaching and jarosite precipitation, as well as the stability of jarosite in acidic plant solutions. A breakthrough came with the finding that jarosite could precipitate under conditions where ferrite would leach satisfactorily. Based on this discovery, a one-step process for the treatment of ferrite was developed. In the plant, the new process almost doubled the recovery of zinc from ferrite in the same equipment as the two-step jarosite process was operated in at that time. In a later expansion of the plant, investment savings were substantial compared to other technologies available. In the solution purification, the key finding was that Co, Ni, and Cu formed specific arsenides in the “hot arsenic zinc dust” step. This was utilized for the development of a three-step purification stage based on fluidized bed technology in all three steps, i.e. removal of Cu, Co and Cd. Both precipitation rates and selectivity increased, which strongly decreased the zinc powder consumption through a substantially suppressed hydrogen gas evolution. Better selectivity improved the value of the precipitates: cadmium, which caused environmental problems in the copper smelter, was reduced from 1-3% reported normally down to 0.05 %, and a cobalt cake with 15 % Co was easily produced in laboratory experiments in the cobalt removal. The zinc powder consumption in the plant for a solution containing Cu, Co, Ni and Cd (1000, 25, 30 and 350 mg/l, respectively), was around 1.8 g/l; i.e. only 1.4 times the stoichiometric demand – or, about 60% saving in powder consumption. Two processes for direct leaching of the concentrate under atmospheric conditions were developed, one of which was implemented in the Kokkola zinc plant. Compared to the existing pressure leach technology, savings were obtained mostly in investment. The scientific basis for the most important processes and process improvements is given in the doctoral thesis. This includes mathematical modeling and thermodynamic evaluation of experimental results and hypotheses developed. Five of the processes developed in this research and development program were implemented in the plant and are still operated. Even though these processes were developed with the focus on the plant in Kokkola, they can also be implemented at low cost in most of the zinc plants globally, and have thus a great significance in the development of the electrolytic zinc process in general.