Heat source modelling and natural ventilation efficiency

We compare natural ventilation flows established by a range of heat source distributions at floor level. Both evenly distributed and highly localised line and point source distributions are considered. We demonstrate that modelling the ventilation flow driven by a uniformly distributed heat source is equivalent to the flow driven by a large number of localised sources. A model is developed for the transient flow development in a room with a uniform heat distribution and is compared with existing models for localised buoyancy inputs. For large vent areas the flow driven by localised heat sources reaches a steady state more rapidly than the uniformly distributed case. For small vent areas there is little difference in the transient development times. Our transient model is then extended to consider the time taken to flush a neutrally buoyant pollutant from a naturally ventilated room. Again comparisons are drawn between uniform and localised (point and line) heat source geometries. It is demonstrated that for large vent areas a uniform heat distribution provides the fastest flushing. However, for smaller vent areas, localised heat sources produce the fastest flushing. These results are used to suggest a definition for the term 'natural ventilation efficiency', and a model is developed to estimate this efficiency as a function of the room and heat source geometries. © 2006 Elsevier Ltd. All rights reserved.

Pollutant flushing with natural displacement ventilation

We examine the time taken to flush pollutants from a naturally ventilated room. A simple theoretical model is developed to predict the time taken for neutrally-buoyant pollutants to be removed from a room by a flow driven by localised heat inputs; both line and point heat sources are considered. We show that the rate of flushing is a function of the room volume, vent areas ( A) and the distribution, number (n) and strength (B) of the heat sources. We also show that the entire problem can be reduced to a single parameter ( μ) that is a measure of the vent areas, and a dimensionless time ( τ) that is a function of B, V and μ. Small-scale salt-bath experiments were conducted to measure the flushing rates in order to validate our modelling assumptions and predictions. The predicted flushing times show good agreement with the experiments over a wide range of μ. We apply our model to a typical open plan office and lecture theatre and discuss some of the implications of our results. © 2005 Elsevier Ltd. All rights reserved.

Fundamental atrium design for natural ventilation

An atrium is a central feature of many modern naturally ventilated building designs. The atrium fills with warm air from the adjoining storeys: this air may be further warmed by direct solar heating in the atrium, and the deep warm layer enhances the flow. In this paper we focus on the degree of flow enhancement achieved by an atrium which is itself 'ventilated' directly, by a low-level connection to the exterior. A theoretical model is developed to predict the steady stack-driven displacement flow and thermal stratification in the building, due to heat gains in the storey and solar gains in the atrium, and compared with the results of laboratory experiments. Direct ventilation of the atrium is detrimental to the ventilation of the storey and the best design is identified as a compromise that provides adequate ventilation of both spaces. We identify extremes of design for which an atrium provides no significant enhancement of the flow, and show that an atrium only enhances the flow in the storey if its upper opening is of an intermediate size, and its lower opening is sufficiently small. © 2003 Elsevier Science Ltd. All rights reserved.

Key principles for developing industrially relevant strategic technology management toolkits

When considering the potential uptake and utilization of technology management tools by industry, it must be recognized that companies face the difficult challenges of selecting, adopting and integrating individual tools into a toolkit that must be implemented within their current organizational processes and systems. This situation is compounded by the lack of sound advice on integrating well-founded individual tools into a robust toolkit that has the necessary degree of flexibility such that they can be tailored for application to specific problems faced by individual organizations. As an initial stepping stone to offering a toolkit with empirically proven utility, this paper provides a conceptual foundation to the development of toolkits by outlining an underlying philosophical position based on observations from multiple research and commercial collaborations with industry. This stance is underpinned by a set of operationalized principles that can offer guidance to organizations when deciding upon the appropriate form, functions and features that should be embodied by any potential tool/toolkit. For example, a key objective of any tool is to aid decision-making and a core set of powerful, flexible, scaleable and modular tools should be sufficient to allow users to generate, explore, shape and implement possible solutions across a wide array of strategic issues. From our philosophical stance, the preferred mode of engagement is facilitated workshops with a participatory process that enables multiple perspectives and structures the conversation through visual representations in order to manage the cognitive load in the collaborative environment. The generic form of the tools should be configurable for the given context and utilized in a lightweight manner based on the premise of 'start small and iterate fast'. © 2012 Elsevier Inc.

A simplified mathematical approach for modelling stack ventilation in multi-compartment buildings

A simple mathematical model of stack ventilation flows in multi-compartment buildings is developed with a view to providing an intuitive understanding of the physical processes governing the movement of air and heat through naturally ventilated buildings. Rules of thumb for preliminary design can be ascertained from a qualitative examination of the governing equations of flow, which elucidate the relationships between 'core' variables - flow rates, air temperatures, heat inputs and building geometry. The model is applied to an example three-storey office building with an inlet plenum and atrium. An examination of the governing equations of flow is used to predict the behaviour of steady flows and to provide a number of preliminary design suggestions. It is shown that control of ventilation flows must be shared between all ventilation openings within the building in order to minimise the disparity in flow rates between storeys, and ensure adequate fresh air supply rates for all occupants. © 2013 Elsevier Ltd.

Stack ventilation in multi-storey atrium buildings: A dimensionless design approach

Using a simplified mathematical model, a preliminary design strategy for steady stack ventilation in multi-storey atrium buildings is developed. By non-dimensionalising the governing equations of flow, two key dimensionless parameters are identified - a ventilation performance indicator, λ, and atrium enhancement parameter, E - which quantify the performance of the ventilation system and the effectiveness of the atrium in assisting flows. Analytical expressions are determined to inform the vent sizes needed to provide the desired balance between indoor air temperature, ventilation flow rate and heat inputs for any distribution of occupants within the building, and also to ensure unidirectional flow. Dimensionless charts for determining the required combination of design variables are presented with a view to informing first-order design guidance for naturally ventilated buildings. © 2013 Elsevier Ltd.

Transient ventilation dynamics induced by heat sources of unequal strength

We examine theoretically the transient displacement flow and density stratification that develops within a ventilated box after two localized floor-level heat sources of unequal strengths are activated. The heat input is represented by two non-interacting turbulent axisymmetric plumes of constant buoyancy fluxes B1 and B2 > B1. The box connects to an unbounded quiescent external environment of uniform density via openings at the top and base. A theoretical model is developed to predict the time evolution of the dimensionless depths λj and mean buoyancies δj of the 'intermediate' (j = 1) and 'top' (j = 2) layers leading to steady state. The flow behaviour is classified in terms of a stratification parameter S, a dimensionless measure of the relative forcing strengths of the two buoyant layers that drive the flow. We find that dδ1/dτ α 1/λ1 and dδ2/dτ α 1/λ2, where τ is a dimensionless time. When S 1, the intermediate layer is shallow (small λ1), whereas the top layer is relatively deep (large λ2) and, in this limit, δ1 and δ2 evolve on two characteristically different time scales. This produces a time lag and gives rise to a 'thermal overshoot', during which δ1 exceeds its steady value and attains a maximum during the transients; a flow feature we refer to, in the context of a ventilated room, as 'localized overheating'. For a given source strength ratio ψ = B1/B2, we show that thermal overshoots are realized for dimensionless opening areas A < Aoh and are strongly dependent on the time history of the flow. We establish the region of {A, ψ} space where rapid development of δ1 results in δ1 > δ2, giving rise to a bulk overturning of the buoyant layers. Finally, some implications of these results, specifically to the ventilation of a room, are discussed. © Cambridge University Press 2013.

Spatial and seasonal variations in benthic algal assemblages in streams in monsoonal Hong Kong

Samples from stone surfaces were collected in pools within four unpolluted hillstreams (two shaded and two unshaded) in monsoonal Hong Kong (lat. 23 degrees N) to elucidate the extent of spatial (within and among streams) and temporal (seasonal) variations in algal biomass and assemblage composition. Sampling continued for over 12 months, incorporating the dry season when streams were at baseflow, and the wet season when spates were frequent. We anticipated that algal biomass would be lower in shaded streams and during the wet season, with associated seasonal differences in assemblage composition or relative abundance of different growth forms (e. g. erect versus prostrate). Benthic chlorophyll a (a proxy for algal biomass) varied among streams from an annual mean of 11.0-22.3 mg m(-2). Dry-season standing stocks were 18% higher than during the wet season when spate-induced disturbance reduced algal standing stocks. Algal biomass varied significantly at the stream scale, but not at the pool scale, and was lower in unshaded streams, where standing stocks may have been limited by high densities of algivorous balitorid loaches (mainly Pseudogastromyzon myersi). An overriding effect of grazers on algal biomass could also have reduced variations resulting from spate-induced disturbance. Significant differences in assemblage composition among streams, which were dominated by diatoms and cyanobacteria (totally 82 taxa) were not systematically related to shading conditions. Seasonal variations in algal assemblages were statistically significant but rather minor, and did not involve major shifts in composition or growth form caused by spate-induced disturbance. The abundance of filamentous cyanobacteria in all the streams may have been due to 'gardening' by balitorid loaches that removed erect or stalked diatoms and favoured cyanobacteria that persist through basal regeneration of filaments. This explanation requires validation through manipulative experiments.

Environmental threats to children's health in Southeast Asia and the Western Pacific

The Southeast Asia and Western Pacific regions contain half of the world's children and are among the most rapidly industrializing regions of the globe. Environmental threats to children's health are widespread and are multiplying as nations in the area undergo industrial development and pass through the epidemiologic transition. These environmental hazards range from traditional threats such as bacterial contamination of drinking water and wood smoke in poorly ventilated dwellings to more recently introduced chemical threats such as asbestos construction materials; arsenic in groundwater; methyl isocyanate in Bhopal, India; untreated manufacturing wastes released to landfills; chlorinated hydrocarbon and organophosphorous pesticides; and atmospheric lead emissions from the combustion of leaded gasoline. To address these problems, pediatricians, environmental health scientists, and public health workers throughout Southeast Asia and the Western Pacific have begun to build local and national research and prevention programs in children's environmental health. Successes have been achieved as a result of these efforts: A cost-effective system for producing safe drinking water at the village level has been devised in India; many nations have launched aggressive antismoking campaigns; and Thailand, the Philippines, India, and Pakistan have all begun to reduce their use of lead in gasoline, with resultant declines in children's blood lead levels. The International Conference on Environmental Threats to the Health of Children, held in Bangkok, Thailand, in March 2002, brought together more than 300 representatives from 35 countries and organizations to increase awareness on environmental health hazards affecting children in these regions and throughout the world. The conference, a direct result of the Environmental Threats to the Health of Children meeting held in Manila in April 2000, provided participants with the latest scientific data on children's vulnerability to environmental hazards and models for future policy and public health discussions on ways to improve children's health. The Bangkok Statement, a pledge resulting from the conference proceedings, is an important first step in creating a global alliance committed to developing active and innovative national and international networks to promote and protect children's environmental health.

Controlling electronic structures by irradiation in single-walled SiC nanotubes: a first-principles molecular dynamics study

Using first-principles molecular dynamics simulations, the displacement threshold energy and defect configurations are determined in SiC nanotubes. The simulation results reveal that a rich variety of defect structures (vacancies, Stone-Wales defects and antisite defects) are formed with threshold energies from 11 to 64 eV. The threshold energy shows an anisotropic behavior and exhibits a dramatic decrease with decreasing tube diameter. The electronic structure can be altered by the defects formed by irradiation, which suggests that the electron irradiation may be a way to use defect engineering to tailor electronic properties of SiC nanotubes.

黄土沟壑区砂石覆盖果园土壤剖面水分分布

以黄土高原沟壑区砂石覆盖苹果园为研究对象,对600 cm范围内土壤剖面水分含量的时间分异和空间分布状况进行了研究。结果表明:600 cm土层范围内,一周年内可划分为冬季增墒期和夏季失墒期两个阶段;土壤剖面水分空间分布随土壤深度的增加呈现波动性变化且稳定性不同,土壤含水量变化幅度随土层深度增加而变小,据此可将600 cm范围内的土壤剖面划分为速变层、相对稳定层、缓变层和稳定层;土壤水分在不同层次上的分布差异,8月土壤剖面不同层次含水量差异最大,11月次之,5月再次之,1月土壤不同层次含水量差异最小。综合看来,除土壤表层因砂石覆盖水分增加外,土壤剖面含水量随土壤深度的增加而减少且趋于稳定,水分下渗能力减弱;冬季土壤含水量多且分布均匀,夏季土壤水分减少且主要集中在上层,此时土壤不同层次水分含量差异大。

我国水土保持监测与发展研究的思考

回顾了水土保持学科及水土保持监测的发展简史,探讨了水土保持监测内容的合理界定,如监测范围、对象、指标等。分析了水土保持基础理论对水土保持监测的支持问题及其相对于水土保持学科的外延性问题。讨论了水土保持监测的过程和成果的深入研究问题,即如何使得监测成果的各类效益更加明显,提出了水土保持监测发展及研究等基本问题。

有限元子域法分析土石混合介质的饱和导水率

在黄土高原水蚀风蚀交错地区,碎石的存在影响着土壤的水力学特性,因此研究土石混合介质的渗流运动对该地区的植被恢复建设具有重要的指导意义。虽然用有限元法分析地下水渗流的工作很多,但对土石混合介质而言,由于有限元法的解题规模迅速增加,其研究甚少。本模型采用子域法矩形单元,假定土石体中石块含量增加不影响土的孔隙率且石块不透水分析了土石混合介质中的渗流过程。结果表明,影响土石混合介质饱和导水率的主要因素是土石介质的含石率;石块的大小基本不影响混合介质饱和导水率;石块分布方式增加水流路径时,会影响混合介质饱和导水率。这一数值分析结论与土石体渗流问题的部分理论结果和试验结果吻合良好。本模型子域法计算效率高,结果较准确,可用于较大规模的土石混合介质渗流分析,还可推广用于土石混合介质的三维分析和多级子域法有限元技术以获得更大规模的解题效果。

泽兰实蝇的生态学特性及对紫茎泽兰的控制作用

紫茎泽兰(Eupatorium adenophorum Spreng)是一种原产于墨西哥的恶性杂草。近年来已严重妨碍了云南省甚至整个西南地区、林、牧业的发展。自1984年8月引进泽兰实蝇(procecidochares utilis Stone)开展了生物防治研究。已在云南境内七个地州（市）定殖扩散。为了解泽兰实蝇的控制作用，本文从研究泽从实蝇生态学特性入手。分析了泽兰实蝇生态学特性与紫茎泽兰生物防治的关系。定量地评价了泽兰实蝇的控制作用。并且应用灰色系统中局势决策方法比较了不同环境条件下的生防效果。其主要结果如下：1、泽兰实蝇雌性与雄性成虫的存活曲线均近于Deevery I型；雌雄一并来看。则成虫存活曲线为Deevery II型；雌性成虫的寿命比雄性长。产卵峰期多在产卵开始后的第二到第四天。2、泽兰实蝇幼虫与成虫均存在密度制约。在平均每雌占有两枝供试产卵枝条时产卵量最大。同时孕育虫的后代也最多。3、泽兰实蝇的净增殖率R. = 24.365。内禀增长率r_m = 0.055。周限增长值λ = 1.057。种群加倍时间t = 12.603天，世代周期T = 58.371天。4、泽兰实蝇幼虫种群的空间分布呈聚集型且接近于负二项分布。一般来说平均拥挤度大的地区，对紫茎泽兰的控制效果也好。5、利用计算机模拟术对泽兰实蝇的控制作用进行拟合。较之以寄生率来评价生防效果更为科学，也更为符合客观实际。6、对不同环境下的控制作用进行局势决策可知，温度较高。湿度偏低的地区。生防效果优于那些温度较低或温、温度均较高的地区。在本文所进行调查的几个样地中，泽兰实蝇控制效果大小的次序依次为：元江＞宜良＞双柏＞思茅。