An assessment of timber dwellings typical of the Queenslander era, and constraints associated with their relocation, component and adaptive reuse when considering 'regeneration'

This paper presents an explanation of why the reuse of building components after demolition or deconstruction is critical to the future of the construction industry. An examination of the historical cause and response to climate change sets the scene as to why governance is becoming increasingly focused on the built environment as a mechanism to controlling waste generation associated with the process of demolition, construction and operation. Through an annotated description to the evolving design and construction methodology of a range of timber dwellings (typically 'Queenslanders' during the eras of 1880-1900, 1900-1920 & 1920-1940) the paper offers an evaluation to the variety of materials, which can be used advantageously by those wishing to 'regenerate' a Queenslander. This analysis of 'regeneration' details the constraints when considering relocation and/ or reuse by adaption including deconstruction of building components against the legislative framework requirements of the Queensland Building Act 1975 and the Queensland Sustainable Planning Act 2009, with a specific examination to those of the Building Codes of Australia. The paper concludes with a discussion of these constraints, their impacts on 'regeneration' and the need for further research to seek greater understanding of the practicalities and drivers of relocation, adaptive and building components suitability for reuse after deconstruction.

A test vehicle for compliance with resilience requirements in index-based e-health systems

Increasingly, national and international governments have a strong mandate to develop national e-health systems to enable delivery of much-needed healthcare services. Research is, therefore, needed into appropriate security and reliance structures for the development of health information systems which must be compliant with governmental and alike obligations. The protection of e-health information security is critical to the successful implementation of any e-health initiative. To address this, this paper proposes a security architecture for index-based e-health environments, according to the broad outline of Australia’s National E-health Strategy and National E-health Transition Authority (NEHTA)’s Connectivity Architecture. This proposal, however, could be equally applied to any distributed, index-based health information system involving referencing to disparate health information systems. The practicality of the proposed security architecture is supported through an experimental demonstration. This successful prototype completion demonstrates the comprehensibility of the proposed architecture, and the clarity and feasibility of system specifications, in enabling ready development of such a system. This test vehicle has also indicated a number of parameters that need to be considered in any national indexed-based e-health system design with reasonable levels of system security. This paper has identified the need for evaluation of the levels of education, training, and expertise required to create such a system.

Human resource characteristics of international new ventures : the role of immigrant entrepreneurs

Immigrant Entrepreneurs (IE) are often portrayed as pushed into self-employment due to employment barriers in their adopted countries. But IE have human resources, like international experience, which can help them form international new ventures (INV). We question the role of IE in INV. We use randomly selected data from 561 young firms from the Comprehensive Australian Study of Entrepreneurial Emergence (CAUSEE) project. We find that IE are over-represented in INV and have many characteristics known to facilitate INV success including more founders, university degree, international connections and technical capability. These findings are relevant to policy makers, and nascent IE.

Response : letter to the editor by Al-Azri and Al-Maniri

Firstly, the authors would like to thank the editor for the opportunity to respond to Dr Al-Azri’s and Dr Al-Maniri’s letter. Secondly, while the current authors also accept that deterrence-based approaches should act as only one corner-stone of a suite of interventions and public policy initiatives designed to improve road safety, deterrence-based approaches have nonetheless consistently proven to be a valuable resource to improve road safety. Dr Al-Azri and Dr Al-Maniri reinforce their assertion about the limited utility of deterrence by citing drink driving research, and the issue of drink driving is particularly relevant within the current context given that the problem of driving after drinking has historically been addressed through deterrence-based approaches. While the effectiveness of deterrence-based approaches to reduce drink driving will always be dependent upon a range of situational and contextual factors (including police enforcement practices, cultural norms, etc), the utilisation of this approach has proven particularly effective within Queensland, Australia. For example, a relatively recent comprehensive review of Random Breath Testing in Queensland demonstrated that this initiative not only had a deterrent impact upon self-reported intentions to drink and drive, but was also found to have significantly reduced alcohol-related fatalities in the state. However, the authors agree that deterrence-based approaches can be particularly transient and thus require constant “topping up” not least through sustained public reinforcement, which was clearly articulated in the seminal work by Homel.

Using Fiber Bragg Grating (FBG) sensors to measure vertical displacements of bridges : a preliminary study

In many bridges, vertical displacements are the most relevant parameter for monitoring in the both short and long term. However, it is difficult to measure vertical displacements of bridges and yet they are among the most important indicators of structural behaviour. Therefore, it prompts a need to develop a simple, inexpensive and yet more practical method to measure vertical displacements of bridges. With the development of fiber-optics technologies, fiber Bragg grating (FBG) sensors have been widely used in structural health monitoring. The advantages of these sensors over the conventional sensors include multiplexing capabilities, high sample rate, small size and electro magnetic interference (EMI) immunity. In this paper, methods of vertical displacement measurements of bridges are first reviewed. Then, FBG technology is briefly introduced including principle, sensing system, characteristics and different types of FBG sensors. Finally, the methodology of vertical displacement measurements using FBG sensors is presented and a trial test is described. It is concluded that using FBG sensors is feasible to measure vertical displacements of bridges. This method can be used to understand global behaviour of bridge‘s span and can further develop for structural health monitoring techniques such as damage detection.

Safety leaders' perceptions of safety culture in a large Australian construction organisation

Safety culture in the construction industry is a growing research area. The unique nature of construction industry works – being project-based, varying in size and focus, and relying on a highly transient subcontractor workforce – means that safety culture initiatives cannot be easily translated from other industries. This paper reports on the first study in a three year collaborative industry and university research project focusing on safety culture practices and development in one of Australia’s largest global construction organisations. The first round of a modified Delphi method is reported, and describes the insights gained from 41 safety leaders’ perceptions and understandings of safety culture within the organisation. In-depth, semi-structured interviews were conducted, and will be followed by a quantitative perception survey with the same sample. Participants included Senior Executives, Corporate Managers, Project Managers, Safety Managers and Site Supervisors. Leaders’ definitions and descriptions of safety culture were primarily action-oriented and some confusion was evident due to the sometimes implicit nature of culture in organisations. Leadership was identified as a key factor for positive safety culture in the organisation, and there was an emphasis on leaders demonstrating commitment to safety, and being visible to the project-based workforce. Barriers to safety culture improvement were also identified, with managers raising diverse issues such as the transient subcontractor workforce and the challenge of maintaining safety as a priority in the absence of safety incidents, under high production pressures. This research is unique in that it derived safety culture descriptions from key stakeholders within the organisation, as opposed to imposing traditional conceptualisations of safety culture that are not customised for the organisation or the construction industry more broadly. This study forms the foundation for integrating safety culture theory and practice in the construction industry, and will be extended upon in future studies within the research program.

Maximising the manufacturer performance value through lean initiatives using cost based model

Numerous tools and techniques have been developed to eliminate or reduce waste and carry out lean concepts in the manufacturing environment. However, appropriate lean tools need to be selected and implemented in order to fulfil the manufacturer needs within their budgetary constraints. As a result, it is important to identify manufacturer needs and implement only those tools, which contribute maximum benefit to their needs. In this research a mathematical model is proposed for maximising the perceived value of manufacturer needs and developed a step-by-step methodology to select best performance metrics along with appropriate lean strategies within the budgetary constraints. With the help of a case study, the proposed model and method have been demonstrated.

Quantifying axial deformation of columns using vibration characteristics

Column elements at a certain level in building are subjected to loads from different tributary areas. Consequently, differential axial deformation among these elements occurs. Adverse effects of differential axial deformation increase with building height and geometric complexity. Vibrating wire, electronic strain and external mechanical strain gauges are used to measure the axial deformations to take adequate provisions to mitigate the adverse effects. These gauges require deploying in or on the elements during their construction in order to acquire necessary measurements continuously. The use of these gauges is therefore inconvenient and uneconomical. This highlights the need for a method to quantify the axial deformation using ambient measurements. This paper proposes a comprehensive vibration based method. The unique capabilities of the proposed method present through an illustrative example.

Seismic capacity of building constructed in slip formed load bearing wall panels

Constructing buildings using slip formed load bearing wall panels is becoming increasingly popular in Sri Lanka due to several advantages; low cost, environmental friendliness and rapid construction technique. These wall panels are already successfully implemented in many low rise buildings. However, the seismic capacities of these buildings have not been properly studied. Few seismic activities reported in Sri Lanka have not caused severe structural damage, but predictions can not be made as to whether this will continue to be the case in the future. This highlights the need to study the seismic capacity of buildings constructed in slip formed load bearing wall panels. This paper presents a study of the seismic capacity of the existing medium rise building.

Quantifying axial deformations of core shear walls using modal parameters

Differential axial deformation between column elements and shear wall elements of cores increase with building height and geometric complexity. Adverse effects due to the differential axial deformation reduce building performance and life time serviceability. Quantifying axial deformations using ambient measurements from vibrating wire, external mechanical and electronic strain gauges in order to acquire adequate provisions to mitigate the adverse effects is well established method. However, these gauges require installing in or on elements to acquire continuous measurements and hence use of these gauges is uneconomical and inconvenient. This motivates to develop a method to quantify the axial deformations. This paper proposes an innovative method based on modal parameters to quantify axial deformations of shear wall elements in cores of buildings. Capabilities of the method are presented though an illustrative example.

Dangers of the after-dark wonderlands : Part A - A review of the impact of physical environment design on nightclub violence

Nightclubs are businesses. Their business is pleasure; however pleasure has its price. People have become increasingly concerned about the problems of violence in society but why do higher levels of violence occur in nightclubs despite the established patterns of behaviour that dictates how we socialise and act? In response, researchers have focused on identifying social and situational factors that may contribute to violence from a government perspective, focusing on a variety of specific issues ranging from financial standpoints with effective target marketing strategies to legal obligations of supplying alcohol and abiding regulatory conditions. There is little research into specific design properties that can determine design standards to ensure/improve the physical design of nightclub environments to reduce patron violence. To address this gap, this current article aims to understand how people experience and respond to the physical environment of nightclubs and how these spaces influence their behaviour. The first section of this paper examines the background on nightclubs and theories concerning the influence of pleasure. The second section of this paper details the findings of existing studies that have examined the nightlife context and the various factors that influence patron violence. The main finding of this paper is that although alcohol likely plays a contributing role in aggressive patron behaviour, there is evidence that the relationship is moderated by a number of significant factors relating to the characteristics of the drinking environment such as: physical comfort; the degree of overall 'permissiveness‘ in the establishment; crowding; and physical environmental elements most influenced by day to-day management practices such as lighting, ventilation, cleanliness and seating arrangements. The findings from this paper have been used to develop a framework to guide exploratory research on how specific elements of the physical environment of nightclubs have an impact on elevated patron aggression and assault (Koleczko & Garcia Hansen, 2011).

Dangers of the after-dark wonderlands : Part B - A review of the impact of the physical environment design on nightclub violence

Violence in nightclubs is a serious problem that has the Australian government launching multimillion dollar drinking campaigns. Research on nightclub violence has focused on identifying contributing social and environmental factors, with many concentrating on a variety of specific issues ranging from financial standpoints with effective target marketing strategies to legal obligations of supplying alcohol and abiding regulatory conditions. Moreover, existing research suggests that there is no single factor that directly affects the rate violence in licensed venues. As detailed in the review paper of Koleczko and Garcia Hansen (2011), there is little research about the physical environment of nightclubs and which specific design properties can be used to determine design standards to ensure/improve the physical design of nightclub environments to reduce patron violence. This current study seeks to address this omission by reporting on a series of interviews with participants from management and design domains. Featured case studies are both located in Fortitude Valley, a Mecca for party-goers and the busiest nightclub district in Queensland. The results and analysis support the conclusions that a number of elements of the physical environment influence elevated patron aggression and assault.

A restrike waveform predictive model for shunt capacitor bank switching with point-on-wave recommendation

Circuit-breakers (CBs) are subject to electrical stresses with restrikes during capacitor bank operation. Stresses are caused by the overvoltages across CBs, the interrupting currents and the rate of rise of recovery voltage (RRRV). Such electrical stresses also depend on the types of system grounding and the types of dielectric strength curves. The aim of this study is to demonstrate a restrike waveform predictive model for a SF6 CB that considered the types of system grounding: grounded and non-grounded and the computation accuracy comparison on the application of the cold withstand dielectric strength and the hot recovery dielectric strength curve including the POW (point-on-wave) recommendations to make an assessment of increasing the CB remaining life. The simulation of SF6 CB stresses in a typical 400 kV system was undertaken and the results in the applications are presented. The simulated restrike waveforms produced with the identified features using wavelet transform can be used for restrike diagnostic algorithm development with wavelet transform to locate a substation with breaker restrikes. This study found that the hot withstand dielectric strength curve has less magnitude than the cold withstand dielectric strength curve for restrike simulation results. Computation accuracy improved with the hot withstand dielectric strength and POW controlled switching can increase the life for a SF6 CB.

Innovation strategies for developing the traditional souvenir craft industry

This paper describes the concept of innovation strategies for traditional souvenir craft industries. There are many traditional souvenir craft industries in Indonesia, and they have to compete in today‘s global markets. The craftsmanship and uniqueness of traditional crafts must be developed to attract a larger market. This competition is not easy for craftspeople, neither financially nor culturally. The authors propose some innovation strategies to facilitate craftspeople in generating ideas based on their traditional value, to ensure their sustainability in global context. However, even though there are a number of studies about the craft industry and souvenirs, there is little research focused on the souvenir product development process, especially in the traditional craft industry. Considering that souvenirs are products for pleasure which require hedonic value more than utilitarian value, the offered innovation strategy refers to the strategy applied in existing industries that produce hedonic products. Innovation strategy in the fashion industry is selected as a reference, which is discussed by considering the context of the traditional souvenir craft industry. This investigation will support further research about knowledge sharing systems to enable collaborative learning within traditional craftspeople.

Ethical tensions and academic leaders

Internationally universities have been characterised by shrinking government funding, fierce competition for student enrolments, and greater pressures to become commercially viable. It is against this complex background that academic leaders have been required to confront and resolve a multitude of conflicting interests as they seek to balance a variety of values in their decision-making processes. In this article we put forward a model of ethical decision-making developed from empirical research and literature. To test the efficacy of the model, a case scenario is posed. The article concludes by raising a number of implications for academic leaders regarding ongoing professional learning needed in this area.