Fixed bed pyrolysis of pulm seed waste for liquid oil production

Among various thermo-chemical conversion processes, pyrolysis is considered as an emerging technology for liquid oil production. The conversion of biomass waste in the form of plum seed into pyrolysis oil by fixed bed pyrolysis reactor has been taken into consideration in this study. A fixed bed pyrolysis has been designed and fabricated for obtaining liquid fuel from this plum seeds. The major component of the system are fixed bed pyrolysis reactor, liquid condenser and liquid collectors. The plum seed in particle form is pyrolysed in an externally heated 7.6 cm diameter and 46 cm high fixed bed reactor with nitrogen as the carrier gas. The reactor is heated by means of a biomass source cylindrical heater from 4000C to 6000C. The products are oil, char and gas. The reactor bed temperature, running time and feed particle size are considered as process parameters. The parameters are found to influence the product yield significantly. A maximum liquid yield of 39 wt% of biomass feed is obtained with particle size of 2.36-4.75 mm at a reactor bed temperature of 520oC with a running time of 120 minutes. The pyrolysis oil obtained at this optimum process conditions are analyzed for some fuel properties and compared with some other biomass derived pyrolysis oils and conventional fuels. The oil is found to possess favorable flash point and reasonable density and viscosity. The higher calorific value is found to be 22.39 MJ/kg which is higher than other biomass derived pyrolysis oils.

Experimental and computer simulation validation of ultrasound phase interference created by lateral inhomogeneity of transit time in replica bone marrow composite models

Purpose: The measurement of broadband ultrasonic attenuation (BUA) in cancellous bone for the assessment of osteoporosis follows a parabolic-type dependence with bone volume fraction; having minima values corresponding to both entire bone and entire marrow. Langton has recently proposed that the primary BUA mechanism may be significant phase interference due to variations in propagation transit time through the test sample as detected over the phase-sensitive surface of the receive ultrasound transducer. This fundamentally simple concept assumes that the propagation of ultrasound through a complex solid : liquid composite sample such as cancellous bone may be considered by an array of parallel ‘sonic rays’. The transit time of each ray is defined by the proportion of bone and marrow propagated, being a minimum (tmin) solely through bone and a maximum (tmax) solely through marrow. A Transit Time Spectrum (TTS), ranging from tmin to tmax, may be defined describing the proportion of sonic rays having a particular transit time, effectively describing lateral inhomogeneity of transit time over the surface of the receive ultrasound transducer. Phase interference may result from interaction of ‘sonic rays’ of differing transit times. The aim of this study was to test the hypothesis that there is a dependence of phase interference upon the lateral inhomogenity of transit time by comparing experimental measurements and computer simulation predictions of ultrasound propagation through a range of relatively simplistic solid:liquid models exhibiting a range of lateral inhomogeneities. Methods: A range of test models was manufactured using acrylic and water as surrogates for bone and marrow respectively. The models varied in thickness in one dimension normal to the direction of propagation, hence exhibiting a range of transit time lateral inhomogeneities, ranging from minimal (single transit time) to maximal (wedge; ultimately the limiting case where each sonic ray has a unique transit time). For the experimental component of the study, two unfocused 1 MHz ¾” broadband diameter transducers were utilized in transmission mode; ultrasound signals were recorded for each of the models. The computer simulation was performed with Matlab, where the transit time and relative amplitude of each sonic ray was calculated. The transit time for each sonic ray was defined as the sum of transit times through acrylic and water components. The relative amplitude considered the reception area for each sonic ray along with absorption in the acrylic. To replicate phase-sensitive detection, all sonic rays were summed and the output signal plotted in comparison with the experimentally derived output signal. Results: From qualtitative and quantitative comparison of the experimental and computer simulation results, there is an extremely high degree of agreement of 94.2% to 99.0% between the two approaches, supporting the concept that propagation of an ultrasound wave, for the models considered, may be approximated by a parallel sonic ray model where the transit time of each ray is defined by the proportion of ‘bone’ and ‘marrow’. Conclusions: This combined experimental and computer simulation study has successfully demonstrated that lateral inhomogeneity of transit time has significant potential for phase interference to occur if a phase-sensitive ultrasound receive transducer is implemented as in most commercial ultrasound bone analysis devices.

A Literature Review of Wellness, Wellbeing and Quality of Life Issues as they impact upon the Australian Mining Sector

Australia’s mining boom Global demand for minerals and energy products has fuelled Australia’s recent resources boom and has led to the rapid expansion of mining projects not only in remote locations but increasingly in settled traditionally agricultural rural areas. A fundamental shift has also occurred in the provisioning of skilled and semi-skilled workers. The huge acceleration in industry demand for labour has been accompanied by the entrenchment of workforce arrangements largely dependent on fly-in, fly-out (FIFO) and drive–in, drive–out (DIDO) non-resident workers (NRWs). While NRWs are working away from their homes, they are usually accommodated in work camps or ‘villages’ for the duration of their work cycle which are normally comprised of many consecutive days of 12-hour day- and night-shifts. The health effects of this form of employment and the accompanying lifestyle is increasingly becoming contentious. Impacts on personal wellness, wellbeing and quality of life essentially remain under-researched and thus misunderstood. Sodexo in Australia Sodexo began operations in Australia in 1982, and has since become a leader in providing Quality of Life (QOL) services to businesses across the country. The 6,000 Australian employees are part of a global Sodexo team of 413,000 people. Sodexo in Australia designs, delivers and manages on-site their QOL services at 320 diverse site locations, including remote sites. Sodexo operates in a range of sectors, including the mining industry. Service plans are tailored to suit the individual needs of organisations. Sodexo Remote Sites has previously conducted unpublished research among mining workers in Australia. The results highlighted needs and expectations of Australian mining workers. Main insights about workers’ requirements were directed towards: • contacts with closest; • warm rest time around proper and varied meals; • additional services to help them better enjoy their life onsite and/or make the most of it; • organise their transportation; • promote community living; and • finding balance between professional and personal life. The brief for this current research is aimed at building upon this knowledge. Research brief Expectations for quality of life and wellness and wellbeing services are increasing dramatically. It's getting costlier and more difficult to retain valuable employees. This is particularly the case in the Australian mining sector. Given the level of interest in ensuring healthy workplaces in Australia, Sodexo has commissioned QUT to conduct a literature review. The objectives as specified by Sodexo are: Objective 1: To define the concepts of wellness and wellbeing and quality of life in Australia Objective 2: To examine how wellness and wellbeing are developed within organisations in Australia and how they impact on employee and organizational performance. More specifically, to review the literature that could be sourced about: • challenges of the mining environment; • the mining lifestyle – implications for health, wellness and daily life; • personal health and wellness of Australian mining workers; • factors affecting health in mines and perceived support for health and wellness; and • the impact of employer investment in health on perceptions and behaviour of employees. Objective 3: To determine what impact employee wellness and well-being has on the performance of mining workers. More specifically, to review the literature that could be sourced about: • impact of obesity, alcohol, tobacco use on companies; and • links between employee engagement and satisfaction and company productivity. Accordingly this review has attempted to ascertain what factors an organisation should focus on in order to reduce absenteeism and turnover and increase commitment, satisfaction, safety and productivity, with specific reference to the mining industry in Australia. The structure of the report aligns with the stated objectives in that each of the first three parts address an objective. Part IV summarises prominent issues that have arisen and offers some concluding observations and comments.

Modelling total duration of traffic incidents including incident detection and recovery time

Traffic incidents are key contributors to non-recurrent congestion, potentially generating significant delay. Factors that influence the duration of incidents are important to understand so that effective mitigation strategies can be implemented. To identify and quantify the effects of influential factors, a methodology for studying total incident duration based on historical data from an ‘integrated database’ is proposed. Incident duration models are developed using a selected freeway segment in the Southeast Queensland, Australia network. The models include incident detection and recovery time as components of incident duration. A hazard-based duration modelling approach is applied to model incident duration as a function of a variety of factors that influence traffic incident duration. Parametric accelerated failure time survival models are developed to capture heterogeneity as a function of explanatory variables, with both fixed and random parameters specifications. The analysis reveals that factors affecting incident duration include incident characteristics (severity, type, injury, medical requirements, etc.), infrastructure characteristics (roadway shoulder availability), time of day, and traffic characteristics. The results indicate that event type durations are uniquely different, thus requiring different responses to effectively clear them. Furthermore, the results highlight the presence of unobserved incident duration heterogeneity as captured by the random parameter models, suggesting that additional factors need to be considered in future modelling efforts.

A review of preschool children's physical activity and sedentary time using objective measures

CONTEXT: Identifying current physical activity levels and sedentary time of preschool children is important for informing government policy and community initiatives. This paper reviewed studies reporting on physical activity and time spent sedentary among preschool-aged children (2-5 years) using objective measures. EVIDENCE ACQUISITION: Databases were searched for studies published up to and including April 2013 that reported on, or enabled the calculation of, the proportion of time preschool children spent sedentary and in light- and moderate to vigorous-intensity physical activity. A total of 40 publications met the inclusion criteria for physical activity and 31 met the inclusion criteria for sedentary time. Objective measures included ActiGraph, Actiwatch, Actical, Actiheart, and RT3 accelerometers, direct observation, and Quantum XL telemetry heart rate monitoring. Data were analyzed in May 2013. EVIDENCE SYNTHESIS: Considerable variation in prevalence estimates existed. The proportion of time children spent sedentary ranged from 34% to 94%. The time spent in light-intensity physical activity and moderate to vigorous-intensity physical activity ranged from 4% to 33% and 2% to 41%, respectively. CONCLUSIONS: The considerable variation of prevalence estimates makes it difficult to determine the "true" prevalence of physical activity and sedentary time in preschool children. Future research should aim to reduce inconsistencies in the employed methodologies to better understand preschoolers' physical activity levels and sedentary behavior.

Differential effects of refractive blur on day and night-time driving performance

Purpose To investigate the effect of different levels of refractive blur on real-world driving performance measured under day and nighttime conditions. Methods Participants included 12 visually normal, young adults (mean age = 25.8 ± 5.2 years) who drove an instrumented research vehicle around a 4 km closed road circuit with three different levels of binocular spherical refractive blur (+0.50 diopter sphere [DS], +1.00 DS, +2.00 DS) compared with a baseline condition. The subjects wore optimal spherocylinder correction and the additional blur lenses were mounted in modified full-field goggles; the order of testing of the blur conditions was randomized. Driving performance was assessed in two different sessions under day and nighttime conditions and included measures of road signs recognized, hazard detection and avoidance, gap detection, lane-keeping, sign recognition distance, speed, and time to complete the course. Results Refractive blur and time of day had significant effects on driving performance (P < 0.05), where increasing blur and nighttime driving reduced performance on all driving tasks except gap judgment and lane keeping. There was also a significant interaction between blur and time of day (P < 0.05), such that the effects of blur were exacerbated under nighttime driving conditions; performance differences were evident even for +0.50 DS blur relative to baseline for some measures. Conclusions The effects of blur were greatest under nighttime conditions, even for levels of binocular refractive blur as low as +0.50 DS. These results emphasize the importance of accurate and up-to-date refractive correction of even low levels of refractive error when driving at night.

Impact of high PV penetration on distribution transformer life time

Integration of rooftop photovoltaics (PVs) in residential networks at moderate penetration levels is becoming a reality in many countries including Australia. Despite the technical challenges in properly accommodating PV units, one of the major benefits is the ability of PV units to extend useful life time of distribution transformers. This effect is not quantified in the existing literature. This paper carries out an analysis into the impacts of rooftop PVs at different penetration levels on the performance of distribution transformers and residential networks. This paper presents a methodology to quantify the benefit of the distribution transformer life extension brought about by customer-owned rooftop PV units. The proposed methodology is applied to a real distribution system with various scenarios, including different penetration levels. The results show the distribution transformer loss-of-life function, as a function of the rooftop PV penetration level, is monotonically decreasing function which saturates after a certain penetration level. The best life improvements occur with transformers that are highly loaded and the presence of a significant PV installation may support the deferral of transformer upgrades.

“Do I really need a nap?”: The role of sleep science in informing sleep practices in early childhood education and care settings

A compelling body of studies identifies the importance of sleep for children’s learning, behavioral regulation, and health. These studies have primarily focused on nighttime sleep or on total sleep duration. The independent contribution of daytime sleep, or napping, in childhood is an emerging research focus. Daytime sleep is particularly pertinent to the context of early childhood education and care (ECEC) where, internationally, allocation of time for naps is commonplace through to the time of school entry. The biological value of napping varies with neurological maturity and with individual circumstance. Beyond the age of 3 years, when monophasic sleep patterns become typical, there is an increasing disjuncture between children’s normative sleep requirements and ECEC practice. At this time, research evidence consistently identifies an association between napping and decreased quality and duration of night sleep. We assess the implications of this evidence for educational practice and health policy. We identify the need to distinguish the functions of napping from those of rest, and assert the need for evidence-based guidelines on sleep–rest practices in ECEC settings to accommodate individual variation in sleep needs. Given both the evidence on the impact of children’s nighttime sleep on long-term trajectories of health and well-being and the high rates of child attendance in ECEC programs, we conclude that policy and practice regarding naptime have significant implications for child welfare and ongoing public health.

A follow up sample of first time drink driving offenders : how many drink drive post offence?

Background Drink driving remains an important issue to address in terms of health and injury prevention even though research shows that over time there has been a steady decline in drink driving. This has been attributed to the introduction of countermeasures such as random breath testing (RBT), changing community attitudes and norms leading to less acceptance of the behaviour and, to a lesser degree, the implementation of programs designed to deter offenders from engaging in drink driving. Most of the research to date has focused on the hard core offenders - those with high blood alcohol content at the time of arrest, and those who have more than one offence. Aims There has been little research on differences within the first offender population or on factors contributing to second offences. This research aims to fill the gap by reporting on those factors in a sample of offenders. Methods This paper reports on a study that involved interviewing 198 first offenders in court and following up this group 6-8 months post offence. Of these original participants, 101 offenders were able to be followed up, with 88 included in this paper on the basis that they had driven a vehicle since the offence. Results Interestingly, while the rate of reported apprehended second offences was low in that time frame (3%), a surprising number of offenders reported that they had driven under the influence at a much higher rate (27%). That is a large proportion of first offenders were willing to risk the much larger penalties associated with a second offence in order to engage in drink driving. Discussion and conclusions Key characteristics of this follow up group are examined to inform the development of a evidence based brief intervention program that targets first time offenders with the goal of decreasing the rate of repeat drink driving.

Characteristics of a sample of first time drink driving offenders in Queensland - a qualitative analysis

Drink driving incidents in the Australian community continue to be a major road safety problem resulting in a third of all fatalities. Drink driving prevalence remains high; with the rate of Australians who self report drink driving remaining at 11%-12.1% [1,2]. The focus of research in the area to date has been with recidivist offenders who have a higher probability of reoffending, while there is comparatively limited research regarding first time offenders. An important and understudied area relates to the characteristics of first offenders and predictors of recidivism. This study examined the findings of in-depth focussed interviews with a sample of 20 individual first time drink driving offenders in Queensland recruited at the time of court mention.

Assessment of antenna characteristic effects on pedestrian and cyclists travel-time estimation based on Bluetooth and WiFi MAC addresses

Monitoring pedestrian and cyclists movement is an important area of research in transport, crowd safety, urban design and human behaviour assessment areas. Media Access Control (MAC) address data has been recently used as potential information for extracting features from people’s movement. MAC addresses are unique identifiers of WiFi and Bluetooth wireless technologies in smart electronics devices such as mobile phones, laptops and tablets. The unique number of each WiFi and Bluetooth MAC address can be captured and stored by MAC address scanners. MAC addresses data in fact allows for unannounced, non-participatory, and tracking of people. The use of MAC data for tracking people has been focused recently for applying in mass events, shopping centres, airports, train stations etc. In terms of travel time estimation, setting up a scanner with a big value of antenna’s gain is usually recommended for highways and main roads to track vehicle’s movements, whereas big gains can have some drawbacks in case of pedestrian and cyclists. Pedestrian and cyclists mainly move in built distinctions and city pathways where there is significant noises from other fixed WiFi and Bluetooth. Big antenna’s gains will cover wide areas that results in scanning more samples from pedestrians and cyclists’ MAC device. However, anomalies (such fixed devices) may be captured that increase the complexity and processing time of data analysis. On the other hand, small gain antennas will have lesser anomalies in the data but at the cost of lower overall sample size of pedestrian and cyclist’s data. This paper studies the effect of antenna characteristics on MAC address data in terms of travel-time estimation for pedestrians and cyclists. The results of the empirical case study compare the effects of small and big antenna gains in order to suggest optimal set up for increasing the accuracy of pedestrians and cyclists’ travel-time estimation.

Solid volume fraction estimation of bone:marrow replica models using ultrasound transit time spectroscopy

The acceptance of broadband ultrasound attenuation (BUA) for the assessment of osteoporosis suffers from a limited understanding of both ultrasound wave propagation through cancellous bone and its exact dependence upon the material and structural properties. It has recently been proposed that ultrasound wave propagation in cancellous bone may be described by a concept of parallel sonic rays; the transit time of each ray defined by the proportion of bone and marrow propagated. A Transit Time Spectrum (TTS) describes the proportion of sonic rays having a particular transit time, effectively describing the lateral inhomogeneity of transit times over the surface aperture of the receive ultrasound transducer. The aim of this study was to test the hypothesis that the solid volume fraction (SVF) of simplified bone:marrow replica models may be reliably estimated from the corresponding ultrasound transit time spectrum. Transit time spectra were derived via digital deconvolution of the experimentally measured input and output ultrasonic signals, and compared to predicted TTS based on the parallel sonic ray concept, demonstrating agreement in both position and amplitude of spectral peaks. Solid volume fraction was calculated from the TTS; agreement between true (geometric calculation) with predicted (computer simulation) and experimentally-derived values were R2=99.9% and R2=97.3% respectively. It is therefore envisaged that ultrasound transit time spectroscopy (UTTS) offers the potential to reliably estimate bone mineral density and hence the established T-score parameter for clinical osteoporosis assessment.

Flood related loss and recovery of intertidal seagrass meadows in southern Queensland, Australia

The loss and recovery of intertidal seagrass meadows were assessed following the flood related catastrophic loss of seagrass meadows in February 1999 in the Sandy Strait, Queensland. Region wide recovery rates of intertidal meadows following the catastrophic disturbance were assessed by mapping seagrass abundance in the northern Great Sandy Strait region prior to and on 3 occasions after widespread loss of seagrass. Meadow-scale assessments of seagrass loss and recovery focussed on two existing Zostera capricorni monitoring meadows in the region. Mapping surveys showed that approximately 90% of intertidal seagrasses in the northern Great Sandy Strait disappeared after the February 1999 flooding of the Mary River. Full recovery of all seagrass meadows took 3 years. At the two study sites (Urangan and Wanggoolba Creek) the onset of Z. capricorni germination following the loss of seagrass occurred 14 months post-flood at Wanggoolba Creek, and at Urangan it took 20 months for germination to occur. By February 2001 (24 months post-flood) seagrass abundance at Wanggoolba Creek sites was comparable to pre-flood abundance levels and full recovery at Urangan sites was complete in August 2001 (31 months post-flood). Reduced water quality characterised by 2–3 fold increases in turbidity and nutrient concentrations during the 6 months following the flood was followed by a 95% loss of seagrass meadows in the region. Reductions in available light due to increased flood associated turbidity in February 1999 were the likely cause of seagrass loss in the Great Sandy Strait region, southern Queensland. Although seasonal cues influence the germination of Z. capricorni, the temporal variation in the onset of seed germination between sites suggests that germination following seagrass loss may be dependent on other factors (eg. physical and chemical characteristics of sediments and water). Elevated dissolved nitrogen concentrations during 1999 at Wanggoolba Creek suggest that this site received higher loads of sediments and nutrients from flood waters than Urangan. The germination of seeds at Wanggoolba Creek one year prior to Urangan coincides with relatively low suspended sediment concentrations in Wanggoolba Creek waters. The absence of organic rich sediments at Urangan for many months following their removal during the 1999 flood may also have inhibited seed germination. Data from population cohort analyses and population growth rates showed that rhizome weight and rhizome elongation rates increased over time, consistent with rapid growth during increases in temperature and light availability from May to October

Evaluation of residence time on nitrogen oxides removal in non-thermal plasma reactor

Non-thermal plasma (NTP) has been introduced over the last few years as a promising after- treatment system for nitrogen oxides and particulate matter removal from diesel exhaust. NTP technology has not been commercialised as yet, due to its high rate of energy consumption. Therefore, it is important to seek out new methods to improve NTP performance. Residence time is a crucial parameter in engine exhaust emissions treatment. In this paper, different electrode shapes are analysed and the corresponding residence time and NOx removal efficiency are studied. An axisymmetric laminar model is used for obtaining residence time distribution numerically using FLUENT software. If the mean residence time in a NTP plasma reactor increases, there will be a corresponding increase in the reaction time and consequently the pollutant removal efficiency increases. Three different screw thread electrodes and a rod electrode are examined. The results show the advantage of screw thread electrodes in comparison with the rod electrode. Furthermore, between the screw thread electrodes, the electrode with the thread width of 1 mm has the highest NOx removal due to higher residence time and a greater number of micro-discharges. The results show that the residence time of the screw thread electrode with a thread width of 1 mm is 21% more than for the rod electrode.

Molecular characterization and pathogenicity of Pythium species associated with damping-off in greenhouse cucumber (Cucumis sativus) in Oman

A study was undertaken in 2004 and 2005 to characterize pathogens associated with damping-off of greenhouse-grown cucumber seedlings in 13 districts in Oman. Identification of Pythium to the species level was based on sequences of the internal transcribed spacer (ITS) of the ribosomal DNA. Of the 98 Pythium isolates collected during the survey, Pythium aphanidermatum, P. spinosum, P. splendens and P. oligandrum accounted for 76%, 22%, 1% and 1%, respectively. Pythium aphanidermatum was isolated from all of the districts, while P. spinosum was isolated from seven districts. Pathogenicity tests showed inter- and intraspecific variation in aggressiveness between Pythium species. Pythium aphanidermatum, P. spinosum and P. splendens were found to be highly aggressive at 25°C. However, the aggressiveness of P. spinosum decreased when the temperature was raised to 30°C, which was found to correspond to the lower frequency of isolation of P. spinosum in the warmer seasons, compared to the cooler time of the year. Pythium aphanidermatum exhibited limited intraspecific variation in the sequences of the ITS region of the rDNA and showed 100% similarity to the corresponding P. aphanidermatum sequences from GenBank. The ITS sequence data, as well as morphological characteristics of P. spinosum isolates, showed a high level of similarity within and between P. spinosum and P. kunmingense, and suggested that the two species were synonymous. This study represents the first report of P. spinosum, P. splendens and P. oligandrum in Oman.