Estudo da sinterização de cavacos de aço ferritico

This research studies the sintering of ferritic steel chips from the machining process. Were sintered metal powder obtained from machining process chips for face milling of a ferritic steel. The chip was produced by machining and characterized by SEM and EDS, and underwent a process of high energy mill powder characterized also by SEM and EDS. Were constructed three types of matrixes for uniaxial compression (relation l / d greater than 2.5). The differences in the design of the matrixes were essentially in the direction of load application, which for cylindrical case axial direction, while for the rectangular arrays, the longer side. Two samples were compressed with different geometries, a cylindrical and rectangular with the same compaction pressure of 700 MPa. The samples were sintered in a vacuum resistive furnace, heating rate 20 °C / min., isotherm 1300 °C for 60 minutes, and cooling rate of 25 °C / min to room temperature. The starting material of the rectangular sample was further annealed up to temperature of 800 ° C for 30 min. Sintered samples were characterized by scanning electron microscopy, optical microscopy and EDS. The sample compressed in the cylindrical matrix did not show a regular density reflecting in the sintered microstructure revealed by the irregular geometry of the pores, characterizing that the sintering was not complete, reaching only the second phase. As for the specimen compacted in the rectangular array, the analysis performed by scanning electron microscopy, optical microscopy and EDS indicate a good densification, and homogeneous microstructure in their full extent. Additionally, the EDS analyzes indicate no significant changes in chemical composition in the process steps. Therefore, it is concluded that recycling of chips, from the processed ferritic steel is feasible by the powder metallurgy. It makes possible rationalize raw material and energy by manufacture of known properties components from chips generated by the machining process, being benefits to the environment

Degradación bacteriana de cianuro y compuestos nitrogenados tóxicos

La ruta de asimilación de cianuro en P. pseudoalcaligenes CECT5344 transcurre a través de un nitrilo formado por la reacción química del cianuro con el oxalacetato, siendo este último acumulado como consecuencia de la acción conjunta de una malato:quinona oxidoreductasa (MQO) y la oxidasa terminal resistente a cianuro (CioAB) (Luque-Almagro et al., 2011b). Los nitrilos pueden ser convertidos en amonio por la acción de una nitrilasa o un sistema nitrilo hidratasa/amidasa. Con el objetivo de elucidar la ruta de asimilación de cianuro en P. pseudoalcalígenes CECT5344, se ha analizado el proteoma de este microorganismo en condiciones cianotróficas frente a nitrato como fuente de nitrógeno como control. En este estudio se identificaron proteínas relacionadas con la ruta de asimilación de cianuro en la estirpe CECT5344, que aparecían inducidas por cianuro, como NitB y NitG, cuyos genes se encuentran localizados en la agrupación génica nit1C. Además de NitB y NitG, de función desconocida, la agrupación génica nit1C codifica un regulador transcripcional del tipo Fis dependiente de σ54 (NitA), una nitrilasa (NitC), una proteína que pertenece a la superfamilia S-adenosilmetionina (NitD), un miembro de la superfamilia N-aciltransferasa (NitE), un polipéptido de la familia AIRS/GARS (NitF) y una oxidorreductasa dependiente de NADH (NitH). Un análisis transcripcional mediante RT-PCR determinó que los genes nitBCDEFGH se cotranscriben, mientras que el gen regulador nitA se transcribe de forma divergente. Además, resultados obtenidos por RT-PCR confirman que la expresión de los genes nitBCDEFGH está inducida por cianuro y reprimida por amonio. La relación entre el cianuro y el grupo de genes nit1C queda patente por el fenotipo de los mutantes deficientes nitA, nitB y nitC, incapaces de usar complejos cianuro-metálicos o 2-hidroxinitrilos como única fuente de nitrógeno. Todos estos datos indican que la nitrilasa NitC, junto con la proteína NitB, utilizan de forma específica determinados nitrilos alifáticos como sustrato, entre los que se encuentran el formado durante la asimilación de cianuro (Estepa et al., 2012). Además, entre las proteínas inducidas por cianuro se identificaron una dihidropicolinato sintasa (DapA), una fosfoserina transaminasa (SerC) y una proteína de función desconocida (Orf1), las tres codificadas por genes del operón cio, una cianasa (CynS), la proteína S6 de la subunidad ribosomal 30S (RpsF), una superóxido dismutasa (SodB), la ferritina (Dps), una oxidorreductasa (Fpr) y un factor de elongación P (EF-P). Una vez identificadas, estas proteínas se han analizado funcionalmente y se han localizado en el genoma de P. pseudoalcaligenes CECT5344 los genes correspondientes, así como los genes adyacentes. La inducción de estas proteínas en condiciones cianotróficas sugiere que el metabolismo del cianuro incluye, además de la resistencia y asimilación de este tóxico, otros procesos biológicos relacionados con el metabolismo del cianato y de algunos aminoácidos, el estrés oxidativo y la homeostasis de hierro, entre otros. Por otra parte, el conocimiento en profundidad y la interpretación de la secuencia génica de P. pseudoalcaligenes CECT5344, así como el análisis comparativo frente a organismos no cianotrofos ha permitido entender algunos de los mecanismos implicados en la resistencia y asimilación de cianuro, lo que permitiría conducir a la posterior mejora del proceso de biodegradación de cianuro. Además, el estudio del genoma de la estirpe CECT5344 permitirá explorar la capacidad de este organismo para ser utilizado en procesos de biorremediación de residuos cianurados en los que se encuentran metales y otros tóxicos (Luque-Almagro et al., 2013; Wibberg et al., 2014). En este trabajo se muestran y discuten los resultados de la secuenciación del genoma de P. pseudoalcaligenes, así como el estudio del análisis filogenético y evolutivo de la cepa, estableciéndose de esta manera relaciones con otras especies en base a los genomas secuenciados de las mismas, entre las que destaca P. mendocina ymp relacionada con P. pseudoalcaligenes CECT5344. El estudio de las características del genoma de P. pseudoalcaligenes CECT5344 ha sido completado con un análisis comparativo frente a los genomas de otras especies de Pseudomonas, encontrándose así semejanzas y diferencias en cuanto a la distribución génica funcional. Por último, se muestra un análisis del genoma de P. pseudoalcaligenes CECT5344 en relación con los genes implicados probablemente en los procesos de asimilación de cianuro y residuos cianurados, tales como los codificantes de nitrilasas y aquellos implicados en la resistencia a cianuro como los constituyentes del operón cio que codifican la oxidasa terminal insensible a cianuro. Finalmente, se discute la presencia de genes implicados posiblemente en otros procesos con una alto potencial biotecnológico, tales como la producción de bioplásticos y la biodegradación de diversos contaminantes.

Revestimentos a base de Ta/Al2O3 produzidos por aspersão térmica sobre substrato metálico

Metal substrates were coated by thermal spraying plasma torch, they were positioned at a distance of 4 and 5 cm from the nozzle exit of the plasma jet. The starting materials were used for deposition of tantalum oxide powder and aluminium. These two materials were mixed and ground into high-energy mill, then immersed in the torch for the production of alumina coating infused with particles of tantalum with nano and micrometric size. The spraying equipment used is a plasma torch arc not transferred, which operating in the range of 250 A and 80 V, was able to produce enough heat to ignite aluminothermic between Ta2O5 and aluminum. Upon reaching the plasma jet, the mixing powders react with the heat of the blaze, which provides sufficient energy for melting aluminum particles. This energy is transferred through mechanisms of self-propagating to the oxide, beginning a reduction reaction, which then hits on the surface of the substrate and forms a coating on which a composite is formed by a junction metal - ceramic (Ta +Al2O3). The phases and quantification of each were obtained respectively by X-ray diffraction and the Rietveld method. Morphology by scanning electron microscopy and chemical analysis by energy dispersive spectroscopy EDS. It was also performed measurements of the substrate roughness, Vickers microhardness measurements in sprays and determination of the electron temperature of the plasma jet by optical emission spectroscopy EEO. The results confirmed the expectation generated around the end product of spraying the mixture Ta2O5 + Al, both in the formation of nano-sized particles and in their final form. The electron excitation temperature was consistent with the purpose of work, in addition, the thermodynamic temperature was efficient for the reduction process of Ta2O5. The electron excitation temperature showed values of 3000, 4500 and 8000 K for flows10, 20 and 30 l / min respectively, these values were taken at the nozzle exit of the plasma jet. The thermodynamic temperature around 1200 ° C, was effective in the reduction process of Ta2O5

Remoção de metais pesados em efluentes sintéticos utilizando vermiculita como adsorvente

Heavy metals are used in many industrial processestheirs discard can harm fel effects to the environment, becoming a serious problem. Many methods used for wastewater treatment have been reported in the literature, but many of them have high cost and low efficiency. The adsorption process has been used as effective for the metal remoal ions. This paper presents studies to evaluate the adsorption capacity of vermiculite as adsorbent for the heavy metals removal in a synthetic solution. The mineral vermiculite was characterized by differents techniques: specific surface area analysis by BET method, X-ray diffraction, raiosX fluorescence, spectroscopy in the infraredd region of, laser particle size analysis and specific gravity. The physical characteristics of the material presented was appropriate for the study of adsorption. The adsorption experiments weredriveal finite bath metod in synthetic solutions of copper, nickel, cadmium, lead and zinc. The results showed that the vermiculite has a high potential for adsorption, removing about 100% of ions and with removal capacity values about 85 ppm of metal in solution, 8.09 mg / g for cadmium, 8.39 mg/g for copper, 8.40 mg/g for lead, 8.26 mg/g for zinc and 8.38 mg/g of nickel. The experimental data fit in the Langmuir and Freundlich models. The kinetic datas showed a good correlation with the pseudo-second order model. It was conducteas a competition study among the metals using vermiculiti a adsorbent. Results showed that the presence of various metals in solution does not influence their removal at low concentrations, removing approximat wasely 100 % of all metals present in solutions

Preparação de óxidos mistos de níquel e zinco nanoparticulados a partir de combustíveis alternativos

The field of "Materials Chemistry" has been developing in recent years and there has been a great increase of interest in the synthesis and chemical and physical properties of new inorganic solids. New routes of synthesis and synthesis modified has been developed with the aim not only to optimize the processes in laboratory scale, but also on an industrial scale, and make them acceptable by current environmental legislation. The phenomenology of current solid state chemistry properties coupled with the high temperature superconductivity, ferromagnetism, porosity molecular and colors are evidence affected by the synthesis method, which in turn can influence the technological application of these materials. From this understanding, mixed oxides of nickel and zinc nanoparticulate were synthesized by microwave-assisted combustion route using three specific types of organic fuels employing the weight ratios 1:1/2 and 1:1 of cation metallic/fuel, in order to investigate the influence of such proportions to obtain the solids. The new fuels were chosen to replace, for example, urea or glycine that are the fuels most commonly preferred in this kind of synthesis. The powders without heat treatment were studied by Thermogravimetric analysis (TGA), X-Ray Diffraction (XRD) and then calcined at 900°C. After heat treatment, the samples were characterized by analysis of X Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The modified synthesis route porposed was effective for obtaining powders. Both the alternative fuels chosen as the different weight ratios employed, influenced in the morphology and obtaining oxides

Estudio experimental del aporte de material en forma de hilo por Laser Cladding

La competencia y la constante evolución del mercado de la Fabricación Aditiva, y en concreto del Laser Cladding, como en cualquier otro mercado industrial, demandan una alta productividad y una buena calidad de los recubrimientos. El objetivo principal de este trabajo, realizado en el Taller de Ingeniería Mecánica de la Universidad del País Vasco, es analizar estos dos factores basándose en el aporte de material en forma de hilo, y hacer una comparación de los resultados que se obtendrían con el aporte de polvo. Como indicador de la productividad se ha utilizado la tasa de aporte, y para analizar la calidad del aporte se han observado los defectos y el crecimiento de los cordones tanto en altura como en anchura. Otros factores como la dilución y la reducción de costes, también se han tenido en cuenta.

Estudo sobre a redução aluminotérmica de Ta2O5 e TiO2 usando descarga de cátodo oco

In this study it was used two metallic oxides, Ta2O5 and TiO2, in order to obtain metallic powders of Ta and Ti through aluminothermic reduction ignited by plasma. Ta2O5 and TiO2 powders were mixed with Al in a planetary mill, using different milling times. A thermal analysis study (DTA and TG) was carried out, in order to know the temperature to react both the mixtures. Then, these mixtures were submitted to a hollow cathode discharge, where they were reacted using aluminothermic reduction ignited by plasma. The product obtained was characterized by XRD and SEM, where it was proven the possibility of producing these metallic particles, different from the conventional process, where metallic ingots are obtained. It was verified that the aluminothermic reduction ignited by plasma is able to produce metallic powders of Ta and Ti, and a higher efficiency was observed to the process with Ta2O5-Al mixtures. Among different microstructural aspects observed, it can be noted the presence of metallic nanoparticles trapped into an Al2O3 matrix, besides acicular structures (titanium) and dendritic structures (tantalum), which are a product characteristic from a fast cooling

Development of advanced catalytic systems for the selective hydrogenolysis of biomass-derived polyols

195 p.

Métodos no convencionales para la preparación de polímeros de coordinación porosos. Una aproximación económica, medioambientalmente amigable y escalable

293 p. El contenido del capítulo 5 está sujeto a confidencialidad

Pigmentos tipo ftalocianinas no sustituidas: obtención y propiedades

Se describe una clase de compuestos de coordinación que han sido de gran importancia industrial y académica durante casi un siglo: la ftalocianina no sustituida y sus complejos metálicos. Se describen sus propiedades químicas y físicas y se presentan las técnicas de sintetización comunes para su obtención.

Aplicações biotecnológicas do supressor de silenciamento de cucumber mosaic virus

Tese de Doutoramento, Ciências Agrárias, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2015

Interacção de complexos de vanádio-citrato com a bomba de cálcio de retículo sarcoplasmático

Dissertação de mest. em Biotecnologia, Departamento de Química e Bioquímica da Faculdade de Ciêicias e Tecnologia, Univ. do Algarve, 2004

Estudo da polimerização térmica de óleos e gorduras

Dissertação (mestrado)—Universidade de Brasília, Instituto de Química, Programa de Pós-Graduação em Química, 2011.

Biological and chemical strategies for the recovery of precious and rare metals as nanoparticles

Tese de Doutoramento, Ciências do Mar da Terra e do Ambiente, Ramo: Ciências e Tecnologias do Ambiente, Especialidade em Biotecnologia, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2016

Estudo termo-mecânico de interconector metálico recoberto com filme de La0,8Ca0,2CrO3 e de interconector cerâmico de La0,8Sr0,2Cr0,92Co0,08O3 para PaCOS

Doped lanthanum chromite ( LaCrO3 ) has been the most common material used as interconnect in solid oxide fuel cells for high temperature ( SOFC-HT ) that enabling the stack of SOFCs. The reduction of the operating temperature, to around 800 º C, of solid oxide fuel cells enabled the use of metallic interconnects as an alternative to ceramic LaCrO3, From the practical point of view, to be a strong candidate for interconnect the material must have good physical and mechanical properties such as resistance to oxidizing and reducing environments, easy manufacture and appropriate thermo-mechanical properties. Thus, a study on the physic-mechanical interconnects La0,8Sr0,2Cr0,92Co0,08O3 ceramics for SOFC -AT obtained by the method of combustion , as well as thermo-mechanical properties of metallic interconnects (AISI 444) covered with La0,8Ca0,2CrO3 by deposition technique by spray-pyrolysis fuel cells for intermediate temperature (IT-SOFCs). The La0,8Sr0,2Cr0,92Co0,08O3 was characterized by X -ray diffraction(XRD) , density and porosity , Vickers hardness (HV) , the flexural strength at room temperature and 900 °C and scanning electron microscopy (SEM). The X -ray diffraction confirmed the phase formation and LaCrO3 and CoCr2O4, in order 6 GPa hardness and mechanical strength at room temperature was 62 MPa ceramic Interconnector. The coated metal interconnects La0,8Ca0,2CrO3 passed the identification by XRD after deposition of the film after the oxidation test. The oxidative behavior showed increased resistance to oxidation of the metal substrate covered by La0,8Ca0,2CrO3 In flexural strength of the coated metal substrate, it was noticed only in the increased room temperature. The a SEM analysis proved the formation of Cr2O3 and (Cr,Mn)3O4 layers on metal substrate and confirmed the stability of the ceramic La0,8 Ca0,2CrO3 film after oxidative test