The value of a saved tree : The lifecycle of CO2-emissions associated with the combination of printing paper and electricity production of wood in the U.S. and Sweden

The pulp- and paper production is a very energy intensive industry sector. Both Sweden and the U.S. are major pulpandpaper producers. This report examines the energy and the CO2-emission connected with the pulp- and paperindustry for the two countries from a lifecycle perspective.New technologies make it possible to increase the electricity production in the integrated pulp- andpaper mill through black liquor gasification and a combined cycle (BLGCC). That way, the mill canproduce excess electricity, which can be sold and replace electricity produced in power plants. In thisprocess the by-products that are formed at the pulp-making process is used as fuel to produce electricity.In pulp- and paper mills today the technology for generating energy from the by-product in aTomlinson boiler is not as efficient as it could be compared to the BLGCC technology. Scenarios havebeen designed to investigate the results from using the BLGCC technique using a life cycle analysis.Two scenarios are being represented by a 1994 mill in the U.S. and a 1994 mill in Sweden.The scenariosare based on the average energy intensity of pulp- and paper mills as operating in 1994 in the U.S.and Sweden respectively. The two other scenarios are constituted by a »reference mill« in the U.S. andSweden using state-of-the-art technology. We investigate the impact of varying recycling rates and totalenergy use and CO2-emissions from the production of printing and writing paper. To economize withthe wood and that way save trees, we can use the trees that are replaced by recycling in a biomassgasification combined cycle (BIGCC) to produce electricity in a power station. This produces extra electricitywith a lower CO2 intensity than electricity generated by, for example, coal-fired power plants.The lifecycle analysis in this thesis also includes the use of waste treatment in the paper lifecycle. Both Sweden and theU.S. are countries that recycle paper. Still there is a lot of paper waste, this paper is a part of the countries municipalsolid waste (MSW). A lot of the MSW is landfilled, but parts of it are incinerated to extract electricity. The thesis hasdesigned special scenarios for the use of MSW in the lifecycle analysis.This report is studying and comparing two different countries and two different efficiencies on theBLGCC in four different scenarios. This gives a wide survey and points to essential parameters to specificallyreflect on, when making assumptions in a lifecycle analysis. The report shows that there arethree key parameters that have to be carefully considered when making a lifecycle analysis of wood inan energy and CO2-emission perspective in the pulp- and paper mill in the U.S. and in Sweden. First,there is the energy efficiency in the pulp- and paper mill, then the efficiency of the BLGCC and last theCO2 intensity of the electricity displaced by BIGCC or BLGCC generatedelectricity. It also show that with the current technology that we havetoday, it is possible to produce CO2 free paper with a waste paper amountup to 30%. The thesis discusses the system boundaries and the assumptions.Further and more detailed research, including amongst others thesystem boundaries and forestry, is recommended for more specificanswers.

Bildens godkännandeprocessi katalogproduktion : The image approval processin a catalog production

The objective of this thesis has been to investigate the approval process for an image. This investigation has been carriedout at four catalog-producing companies and three companies working with repro or printing. The information wasgathered through interviews and surveys and later used for evaluation. The result of the evaluation has shown that allbusinesses are very good at technical aspects but also that the biggest problem they have is with the communication. Theconclusion is that businesses need a clear construction for the image process. This will minimize the communicationproblems and make the process effective.

Production and Delivery (Optimization of production system and reliability)

This thesis is done to solve two issues for Sayid Paper Mill Ltd Pakistan. Section one deals with a practical problem arise in SPM that is cutting a given set of raw paper rolls of known length and width, and a set of product paper rolls of known length (equal to the length of raw paper rolls) and width, practical cutting constraints on a single cutting machine, according to demand orders for all customers. To solve this problem requires to determine an optimal cutting schedule to maximize the overall cutting process profitability while satisfying all demands and cutting constraints. The aim of this part of thesis is to develop a mathematical model which solves this problem.Second section deals with a problem of delivering final product from warehouse to different destinations by finding shortest paths. It is an operational routing problem to decide the daily routes for sending trucks to different destination to deliver their final product. This industrial problem is difficult and includes aspect such as delivery to a single destination and multiple destinations with limited resources. The aim of this part of thesis is to develop a process which helps finding shortest path.

INVENTORY CONTROL SYSTEM : Optimization of production system and reliability

The main idea of this research to solve the problem of inventory management for the paper industry SPM PVT limited. The aim of this research was to find a methodology by which the inventory of raw material could be kept at minimum level by means of buffer stock level.The main objective then lies in finding the minimum level of buffer stock according to daily consumption of raw material, finding the Economic Order Quantity (EOQ) reorders point and how much order will be placed in a year to control the shortage of raw material.In this project, we discuss continuous review model (Deterministic EOQ models) that includes the probabilistic demand directly in the formulation. According to the formula, we see the reorder point and the order up to model. The problem was tackled mathematically as well as simulation modeling was used where mathematically tractable solution was not possible.The simulation modeling was done by Awesim software for developing the simulation network. This simulation network has the ability to predict the buffer stock level based on variable consumption of raw material and lead-time. The data collection for this simulation network is taken from the industrial engineering personnel and the departmental studies of the concerned factory. At the end, we find the optimum level of order quantity, reorder point and order days.

Acoustic Variability in the Production of English Vowels by Native and Non-Native Speakers

The features of non-native speech which distinguish it from native speech are often difficult to pin down. It is possible to be a native speaker of any of a vast number of varieties of English. These varieties each have their phonetic characteristics which allow them to be identified by speakers of the varieties in question and by others. The phonetic differences between the accents represented by these varieties are very great. It is impossible to indicate any particular configuration of vowels in the acoustic vowel space or set of consonant articulations which all native-speaker varieties of English have in common and which non-native speakers do not share. This study considers the vowel quality in a single word by native and non-native speakers.

A Cost Model for the Effect of Setup Time Reduction in Stainless Steel Strip Production

Setup time reduction facilitate the flexibility needed for just-in-time production. An integrated steel mill with meltshop, continuous caster and hot rolling mill is often operated as decoupled processes. Setup time reduction provides the flexibility needed to reduce buffering, shorten lead times and create an integrated process flow. The interdependency of setup times, process flexibility and integration were analysed through system dynamics simulation. The results showed significant reductions of energy consumption and tied capital. It was concluded that setup time reduction in the hot strip mill can aid process integration and hence improve production economy while reducing environmental impact.

Produktion, skador och grenegenskaper hos 10-årig tall i ett kombinerat förbands- och avkommeförsök : Volume production, damages and branch properties in a 10-year old combined spacing and progeny trial of Scots pine

A Scots pine (Pinus sylvestris) progeny trial was established in 1990, in the southwestern part of Sweden. The offspring was from 30 plus trees. The trial is located on abandoned agricultural land and has a single tree block design with a variation in spacing. The trial has been damaged by voles. At a tree age of ten years, growth, damages and branch properties were estimated. An analysis of variance on height, diameter and stem volume shows significant difference between spacing and progenies as well as interactions between these factors. As indicated by a better annual height increment and fewer and thinner branches at each whorl the densest spacing has the highest potential to produce quality logs.There were also differences between progenies in growth and quality traits. Some progenies combined good growth and branch characters with low mortality, straight stems and few damages. Other progenies had superior volume production.

Simulation of Photovoltaic Panel Production as Complement to Ground Source Heat Pump System

This master thesis presents a new technological combination of two environmentally friendly sources of energy in order to provide DHW, and space heating. Solar energy is used for space heating, and DHW production using PV modules which supply direct current directly to electrical heating elements inside a water storage tank. On the other hand a GSHP system as another source of renewable energy provides heat in the water storage tank of the system in order to provide DHW and space heating. These two sources of renewable energy have been combined in this case-study in order to obtain a more efficient system, which will reduce the amount of electricity consumed by the GSHP system.The key aim of this study is to make simulations, and calculations of the amount ofelectrical energy that can be expected to be produced by a certain amount of PV modules that are already assembled on a house in Vantaa, southern Finland. This energy is then intended to be used as a complement to produce hot water in the heating system of the house beside the original GSHP system. Thus the amount of electrical energy purchased from the grid should be reduced and the compressor in the GSHP would need fewer starts which would reduce the heating cost of the GSHP system for space heating and providing hot water.The produced energy by the PV arrays in three different circuits will be charged directly to three electrical heating elements in the water storage tank of the existing system to satisfy the demand of the heating elements. The excess energy can be used to heat the water in the water storage tank to some extent which leads to a reduction of electricity consumption by the different components of the GSHP system.To increase the efficiency of the existing hybrid system, optimization of different PV configurations have been accomplished, and the results are compared. Optimization of the arrays in southern and western walls shows a DC power increase of 298 kWh/year compared with the existing PV configurations. Comparing the results from the optimization of the arrays on the western roof if the intention is to feed AC power to the components of the GSHP system shows a yearly AC power production of 1,646 kWh.This is with the consideration of no overproduction by the PV modules during the summer months. This means the optimized PV systems will be able to cover a larger part of summer demand compared with the existing system.

Printing colour hard proofs using EFI Colorproof XF v. 3.1 and Photoshop CS3, and production substrates.

EFI Colorproof XF was found to be more convenient from a user’s aspect, and had features which are covered in the ISO 12647-7 standard (e.g. the ability to simulate screening and print margin information), which Photoshop CS3 lacked. None of the proofing systems distinguished itself in a clear way from the other; sometimes, on certain substrates, Photoshop CS3 produced most accurate colours, sometimes EFI Colorproof XF did. Further investigations need to be carried out to tell more exactly which system produce most accurate colours. Only 6 out of 34 simulation-combinations had colours within the tolerances in the standard. The result also shows that the production substrates should not be used as proofing substrates. Instead the proofing papers especially made for ink jet should be used to obtain more colour-accurate prints.

Videography as production nexus : digital film cameras, media mangement and the distribution of creativity

This thesis is about new digital moving image recording technologies and how they augment the distribution of creativity and the flexibility in moving image production systems, but also impose constraints on how images flow through the production system. The central concept developed in this thesis is ‘creative space’ which links quality and efficiency in moving image production to time for creative work, capacity of digital tools, user skills and the constitution of digital moving image material. The empirical evidence of this thesis is primarily based on semi-structured interviews conducted with Swedish film and TV production representatives.This thesis highlights the importance of pre-production technical planning and proposes a design management support tool (MI-FLOW) as a way to leverage functional workflows that is a prerequisite for efficient and cost effective moving image production.

The attractiveness of the work is affected when production of handcrafted log houses moves indoors

Viewed from a historical perspective, a shift has occurred within the forestry and wood sector towards indoor work. In Sweden, the production of handcrafted log houses has now also begun to move indoors. With a point of departure in development processes within the log house sector involving working indoors, education, work attractiveness, between 2001-2005, the aim of this study was to compare indoor work with outdoor work, based on log house builders' experience of working on handcrafted log houses. Methods used in the interactive development project involving apprentices, experienced log house builders and researchers, were participation with continuous documentation of experiences and opinions; questions; interviews; and measurement of the work environment. The Attractive Work Model has been used in order to analyse perceptions and values. The changes, 15 out of 22 areas, were perceived both negatively and positively. Therefore, it can not be said that working on traditional, handcrafted log houses becomes more attractive if it is moved indoors. The majority wanted to work both outdoors and indoors, while most of the others only wanted to work outdoors. The results indicate that there is scope for developing more attractive work indoors by utilising experiences from log house builders and closely related activities such as the forestry and wood sector. Changes made within one area of work attractiveness affect other areas. Further research is needed both with regard to comparisons between indoor and outdoor work and regarding the interaction between the areas that are identified in the Attractive Work Model.

La formation d’une identité à l’intersection du genre, de l’ethnie et de la classe : Une analyse intersectionnelle de L’Amant de Marguerite Duras

Dans ce mémoire, nous nous sommes servies d’une méthode thématique pour faire une analyseintersectionnelle de L’Amant de Marguerite Duras. Le but était d’étudier la manière complexedont les différentes structures de domination interagissent l’une avec l’autre dans une sociétécoloniale. L’étude a été concentrée sur la recherche d’une identité personnelle effectuée par leprotagoniste féminin et nous avons voulu savoir comment cette recherche est influencée par lesstructures de genre, d’ethnie et de classe.Notre conclusion est que l’appartenance à la catégorie « blanche et pauvre » donne auprotagoniste un sentiment d’aliénation vis-à-vis de la communauté colonisatrice blanche. Cettealiénation l’aide à s’opposer à certaines normes, par exemple le manque de liberté sociale etsexuelle de la femme, en même temps que son comportement peut parfois être interprété commeune confirmation des rôles racistes existant dans la colonie. Néanmoins, nous voulons soulignerque c’est la façon dont l’amant chinois a été décrit qui est troublante, plutôt que lecomportement du protagoniste féminin.

The priority of temporal aspects in L2-Swedish prosody : Studies in perception and production

Foreign accent can be everything from hardly detectable to rendering the second language speech unintelligible. It is assumed that certain aspects of a specific target language contribute more to making the foreign accented speech intelligible and listener friendly, than others. The present thesis examines a teaching strategy for Swedish pronunciation in second language education. The teaching strategy “Basic prosody” or BP, gives priority to temporal aspects of Swedish prosody, which means the temporal phonological contrasts word stress and quantity, as well as the durational realizations of these contrasts. BP does not prescribe any specific tonal realizations. This standpoint is based on the great regional variety in realization and distribution of Swedish word accents. The teaching strategy consists virtually of three directives: · Stress the proper word in the sentence. · Stress proper syllables in stressed words and make them longer. · Lengthen the proper segment – vowel or subsequent consonant – in the stressed syllable. These directives reflect the view that all phonological length is stress-induced, and that vowel length and consonant length are equally important as learning goals. BP is examined in the light of existing findings in the field of second language pronunciation and with respect to the phonetic correlates of Swedish stress and quantity. Five studies examine the relation between segment durations and the categorization made by native Swedish listeners. The results indicate that the postvocalic consonant duration contributes to quantity categorization as well as giving the proper duration to stressed syllables. Furthermore, native Swedish speakers are shown to apply the complementary /V: C/ - /VC:/ pattern also when speaking English and German, by lengthening postvocalic consonants. The correctness of the priority is not directly addressed but important aspects of BP are supported by earlier findings as well as the results from the present studies.