Wear of high aluminium zinc-based alloys in plain bearing applications

Two zinc-based alloys of high aluminium content, Super Cosmal alloy containing 60% Al, 6% Si, 1% Cu, 0.3% Mn and HAZCA alloy containing 60% Al, 8% Si, 2% Cu, 0.06% Mg were produced by sand casting. Foundry characteristics in particular, fluidity, mode of solidification and feeding ability were examined. Metallographic analysis of structures was carried out using optical and scanning electron microscopy and their mechanical properties were determined using standard techniques. Dry wear characteristics were determined using a pin-on-disc test, and boundary-lubricated wear was studied using full bearing tests. Results from casting experiments were evaluated and compared with the behaviour of a standard ZA-27 alloy and those from tribological tests with both ZA-27 alloy and a leaded tin-bronze (SAE660) under the same testing conditions. The presence of silicon was beneficial, reducing the temperature range of solidification, improving feeding efficiency and reducing gravity segregation of phases. Use of chills and melt degassing was found necessary to achieve soundness and enhanced mechanical properties. Dry wear tests were performed against a steel counterface for sliding speeds of 0.25, 0.5, 1.0 and 2 m/s and for a range of loads up to 15 kgf. The high aluminium alloys showed wear rates as low as those of ZA-27 at speeds of 0.25 and 0.5 m/s for the whole range of applied loads. ZA-27 performed better at higher speeds. The build up of a surface film on the wearing surface of the test pins was found to be responsible for the mild type of wear of the zinc based alloys. The constitution of the surface film was determined as a complex mixture of aluminium, zinc and iron oxides and metallic elements derived from both sliding materials. For full bearing tests, bushes were machined from sand cast bars and were tested against a steel shaft in the presence of a light spindle oil as the lubricant. Results showed that all zinc based alloys run-in more rapidly than bronze, and that wear in Super Cosmal and HAZCA alloys after prolonged running were similar to those in ZA-27 bearings and significantly smaller than those of the bronze.

Exploring the correlation between lipid packaging in lipoplexes and their transfection efficacy

Whilst there is a large body of evidence looking at the design of cationic liposomes as transfection agents, correlates of formulation to function remain elusive. In this research, we investigate if lipid packaging can give further insights into transfection efficacy. DNA lipoplexes composed of 1,2-dioleoyl-sn-glycero-3-phosphoethanolamine (DOPE) or 1,2-distearoyl-sn-glycero-3-phosphoethanolamine (DSPE) in combination with 1,2-dioleoyl-3-trimethylammonium-propane (DOTAP) or 1,2-stearoyl-3-trimethylammonium-propane (DSTAP) were prepared by the lipid hydration method. Each of the formulations was prepared by hydration in dH2O or phosphate buffer saline (PBS) to investigate the effect of buffer salts on lipoplex physicochemical characteristics and in vitro transfection. In addition, Langmuir monolayer studies were performed to investigate any possible correlation between lipid packaging and liposome attributes. Using PBS, rather than dH2O, to prepare the lipoplexes increased the size of vesicles in most of formulations and resulted in variation in transfection efficacies. However, one combination of lipids (DSPE:DOTAP) could not form liposomes in PBS, whilst the DSPE:DSTAP combination could not form liposomes in either aqueous media. Monolayer studies demonstrated saturated lipid combinations offered dramatically closer molecular packing compared to the other combinations which could suggest why this lipid combination could not form vesicles. Of the lipoplexes prepared, those formulated with DSTAP showed higher transfection efficacy, however, the effect of buffer on transfection efficiency was formulation dependent. © 2011 by the authors; licensee MDPI, Basel, Switzerland.

Reverse resource exchanges in service supply chains:the case of returnable transport packaging

Purpose: The purpose of this paper is to understand how reverse resource exchanges and resource dependencies are managed in the service supply chain (SSC) of returnable transport packaging (RTP). Design/methodology/approach: A single case study was conducted in the context of automotive logistics focusing on the RTP SSC. Data were collected through 16 interviews, primarily with managers of a logistics service provider (LSP) and document analysis of contractual agreements with key customers of the packaging service. Findings: Resource dependencies among actors in the SSC result from the importance of the RTP for the customer’s production processes, the competition among users for RTP and the negative implications of the temporary unavailability of RTP for customers and the LSP (in terms of service performance). Amongst other things, the LSP is dependent on its customers and third-party users (e.g. the customer’s suppliers) for the timely return of package resources. The role of inter-firm integration and collaboration, formal contracts as well as customers’ power and influence over third-party RTP users are stressed as key mechanisms for managing LSP’s resource dependencies. Research limitations/implications: A resource dependence theory (RDT) lens is used to analyse how reverse resource exchanges and associated resource dependencies in SSCs are managed, thus complementing the existing SSC literature emphasising the bi-directionality of resource flows. The study also extends the recent SSC literature stressing the role of contracting by empirically demonstrating how formal contracts can be mobilised to explicate resource dependencies and to specify, and regulate, reverse exchanges in the SSC. Practical implications: The research suggests that logistics providers can effectively manage their resource dependencies and regulate reverse exchanges in the SSC by deploying contractual governance mechanisms and leveraging their customers’ influence over third-party RTP users. Originality/value: The study is novel in its application of RDT, which enhances our understanding of the management of reverse exchanges and resource dependencies in SSCs.

Hidden in plain sight:low-literacy adults in a developed country overcoming social and educational challenges through mobile learning support tools

Illiteracy is often associated with people in developing countries. However, an estimated 50 % of adults in a developed country such as Canada lack the literacy skills required to cope with the challenges of today's society; for them, tasks such as reading, understanding, basic arithmetic, and using everyday items are a challenge. Many community-based organizations offer resources and support for these adults, yet overall functional literacy rates are not improving. This is due to a wide range of factors, such as poor retention of adult learners in literacy programs, obstacles in transferring the acquired skills from the classroom to the real life, personal attitudes toward learning, and the stigma of functional illiteracy. In our research we examined the opportunities afforded by personal mobile devices in providing learning and functional support to low-literacy adults. We present the findings of an exploratory study aimed at investigating the reception and adoption of a technological solution for adult learners. ALEX© is a mobile application designed for use both in the classroom and in daily life in order to help low-literacy adults become increasingly literate and independent. Such a solution complements literacy programs by increasing users' motivation and interest in learning, and raising their confidence levels both in their education pursuits and in facing the challenges of their daily lives. We also reflect on the challenges we faced in designing and conducting our research with two user groups (adults enrolled in literacy classes and in an essential skills program) and contrast the educational impact and attitudes toward such technology between these. Our conclusions present the lessons learned from our evaluations and the impact of the studies' specific challenges on the outcome and uptake of such mobile assistive technologies in providing practical support to low-literacy adults in conjunction with literacy and essential skills training. © 2013 Her Majesty the Queen in Right of Canada.

Toughness variations during the tempering of a plain carbon, martensitic steel

The aim of this paper is to present results of toughness measurements and fractographic observations made on a quenched and tempered 0. 6%, carbon steel and to use these as a basis for a discussion of the factors affecting "623K (350 °C) embrittlement" (one-step temper embrittlement).

Representation and misrepresentation of scientific evidence in contemporary tobacco regulation:a review of tobacco industry submissions to the UK Government consultation on standardised packaging

BACKGROUND: Standardised packaging (SP) of tobacco products is an innovative tobacco control measure opposed by transnational tobacco companies (TTCs) whose responses to the UK government's public consultation on SP argued that evidence was inadequate to support implementing the measure. The government's initial decision, announced 11 months after the consultation closed, was to wait for 'more evidence', but four months later a second 'independent review' was launched. In view of the centrality of evidence to debates over SP and TTCs' history of denying harms and manufacturing uncertainty about scientific evidence, we analysed their submissions to examine how they used evidence to oppose SP. METHODS AND FINDINGS: We purposively selected and analysed two TTC submissions using a verification-oriented cross-documentary method to ascertain how published studies were used and interpretive analysis with a constructivist grounded theory approach to examine the conceptual significance of TTC critiques. The companies' overall argument was that the SP evidence base was seriously flawed and did not warrant the introduction of SP. However, this argument was underpinned by three complementary techniques that misrepresented the evidence base. First, published studies were repeatedly misquoted, distorting the main messages. Second, 'mimicked scientific critique' was used to undermine evidence; this form of critique insisted on methodological perfection, rejected methodological pluralism, adopted a litigation (not scientific) model, and was not rigorous. Third, TTCs engaged in 'evidential landscaping', promoting a parallel evidence base to deflect attention from SP and excluding company-held evidence relevant to SP. The study's sample was limited to sub-sections of two out of four submissions, but leaked industry documents suggest at least one other company used a similar approach. CONCLUSIONS: The TTCs' claim that SP will not lead to public health benefits is largely without foundation. The tools of Better Regulation, particularly stakeholder consultation, provide an opportunity for highly resourced corporations to slow, weaken, or prevent public health policies.

A critical evaluation of the volume, relevance and quality of evidence submitted by the tobacco industry to oppose standardised packaging of tobacco products

OBJECTIVES: To examine the volume, relevance and quality of transnational tobacco corporations' (TTCs) evidence that standardised packaging of tobacco products 'won't work', following the UK government's decision to 'wait and see' until further evidence is available. DESIGN: Content analysis. SETTING: We analysed the evidence cited in submissions by the UK's four largest TTCs to the UK Department of Health consultation on standardised packaging in 2012. OUTCOME MEASURES: The volume, relevance (subject matter) and quality (as measured by independence from industry and peer-review) of evidence cited by TTCs was compared with evidence from a systematic review of standardised packaging . Fisher's exact test was used to assess differences in the quality of TTC and systematic review evidence. 100% of the data were second-coded to validate the findings: 94.7% intercoder reliability; all differences were resolved. RESULTS: 77/143 pieces of TTC-cited evidence were used to promote their claim that standardised packaging 'won't work'. Of these, just 17/77 addressed standardised packaging: 14 were industry connected and none were published in peer-reviewed journals. Comparison of TTC and systematic review evidence on standardised packaging showed that the industry evidence was of significantly lower quality in terms of tobacco industry connections and peer-review (p<0.0001). The most relevant TTC evidence (on standardised packaging or packaging generally, n=26) was of significantly lower quality (p<0.0001) than the least relevant (on other topics, n=51). Across the dataset, TTC-connected evidence was significantly less likely to be published in a peer-reviewed journal (p=0.0045). CONCLUSIONS: With few exceptions, evidence cited by TTCs to promote their claim that standardised packaging 'won't work' lacks either policy relevance or key indicators of quality. Policymakers could use these three criteria-subject matter, independence and peer-review status-to critically assess evidence submitted to them by corporate interests via Better Regulation processes.

Reading before buying - exploring consumer attitudes toward informative function of packaging

Oftentimes, packaging is the first and only marketing tool consumers encounter before a purchase, therefore it is considered to be the most important communication and informative tool (Behaegel, 1991; Peters, 1994). The aim of the research is to better understand food label usage of consumers. To make the identification of behaviour patterns possible and to understand the way consumers use labels on packaging netnography has been chosen as the research method. We identified market factors in our research which result in label use. Based on our results, two large consumer segments were identified: conscious and non-conscious consumer behaviours. Reading information on packaging can be classified in two ways, according to method of use (superficial, conditional, incidental) and place (home, or point of sale).

A csomagoláson található információtartalom újragondolása sokdimenziós skálázással az élelmiszeripar példáján (Rethinking of information content on food packaging using multidimensional scaling)

A csomagolás részét képezi a jelölés – vagy más néven címke, label –, aminek elsődleges funkciója a termék tulajdonságairól való tájékoztatás, amellett, hogy a vállalat és a fogyasztó egyik legfontosabb találkozási pontja. Kiemelt szerepe van a marketing és a vállalati menedzsment eszköztárában, hiszen a fogyasztói döntéshozatal meghatározó forrása. A szerző írásában a jelölések definícióját, fajtáit és csoportosítását tárja az olvasó elé, majd ismerteti jelentőségét, fontosságát és szerepét az élelmiszer-ipari termékek segítségével. Ezután egy 630 fős megkérdezés eredményeképp a sokdimenziós skálázás (MDS) módszerével a jelölések új értelmezését mutatja be: a jelöléseket három dimenzió mentén lehet elhelyezni (előzetes tudás, érdek, megbízhatóság), valamint ezenkívül a jelölések öt homogén csoportot alkotnak (klasszikus, diétás, funkcionális, tudatos, előállítási). A téma jelentőségét az egészség és a környezet iránti növekvő érdeklődés, valamint a változó jogszabályi környezet is alátámasztja. / === / Signs, labels, claims are to inform consumers of product attributes, and are part of the packaging. Labeling is one of the most important marketing and management tool, while purchase decision is made at the point of purchase. The aim of this paper is to present the basic definitions and elements of information content on food packaging. The author developed a new approach to examine labeling using multidimensional scaling as a result of a pilot study. Labels are to distinguish through three dimensions: precognition, interest and reliability. Beyond that labels can be sorted to five homogeneous clusters based on classic, dietary, functional, conscious and production attributes. The relevancy of labeling is supported by growing interest of health and environmental issues and changing law environment.

Through wafer 3D Vertical Micro-Coaxial Probe for high frequency material characterization and millimeter wave packaging systems

This work presents the development of an in-plane vertical micro-coaxial probe using bulk micromachining technique for high frequency material characterization. The coaxial probe was fabricated in a silicon substrate by standard photolithography and a deep reactive ion etching (DRIE) technique. The through-hole structure in the form of a coaxial probe was etched and metalized with a diluted silver paste. A co-planar waveguide configuration was integrated with the design to characterize the probe. The electrical and RF characteristics of the coaxial probe were determined by simulating the probe design in Ansoft's High Frequency Structure Simulator (HFSS). The reflection coefficient and transducer gain performance of the probe was measured up to 65 GHz using a vector network analyzer (VNA). The probe demonstrated excellent results over a wide frequency band, indicating its ability to integrate with millimeter wave packaging systems as well as characterize unknown materials at high frequencies. The probe was then placed in contact with 3 materials where their unknown permittivities were determined. To accomplish this, the coaxial probe was placed in contact with the material under test and electromagnetic waves were directed to the surface using the VNA, where its reflection coefficient was then determined over a wide frequency band from dc-to -65GHz. Next, the permittivity of each material was deduced from its measured reflection coefficients using a cross ratio invariance coding technique. The permittivity results obtained when measuring the reflection coefficient data were compared to simulated permittivity results and agreed well. These results validate the use of the micro-coaxial probe to characterize the permittivity of unknown materials at high frequencies up to 65GHz.