Adaptation of "Niagara Rosada" grape must to winemaking by partial cluster dehydration

This study aimed to verify the influence of partial dehydration of "Niagara Rosada" grape clusters in physicochemical quality of the pre- fermentation must. In Brazil, during the winemaking process it is common to need to adjust the grape must when the physicochemical characteristics of the raw material are insufficient to produce wines in accordance with the Brazilian legislation for classification of beverages, which establishes the minimum alcohol content of 8.6 % for the beverage to be considered wine. Therefore, given that the reduction in the water content of grape berries allows the concentration of chemical compounds present in its composition, especially the concentration of total soluble solids, we proceeded with the treatments that were formed by the combination of two temperatures (T1-37.1ºC and T2-22.9 ºC) two air speeds (S1: 1.79 m s-1 and S2: 3.21 m s-1) and a control (T0) that has not gone through the dehydration treatment. Analysis of pH, Total Titratable Acidity (TTA) were performed in mEq L-1, Total Soluble Solids (TSS) in ºBrix, water content on a dry basis and Concentration of Phenolic Compounds (CPC) in mg of gallic acid per 100g of must. The average comparison test identified statistically significant modifications for the adaptation of must for winemaking purposes, having the treatment with 22.9 ºC and air speed of 1.79 m s-1 shown the largest increase in the concentration of total soluble solids, followed by the second best result for concentration of phenolic compounds.

Quality of peanut mechanical sowing in function of seeding density and size of the seeds

ABSTRACTPeanut crop (Arachis hypogaeaL.) mechanization has been improved over the years; however there are drawbacks that affect the quality of operations. Thus, this article’s objectives were to evaluate the operational performance of the mechanized sowing of peanut crop according to seeding densities (10, 14, and 18 seeds m-1) and seed sizes (21 and 23 mm). It was observed that the seeds of 23 mm had shorter average number of days to emergence and a higher percentage of emergences, occurring the opposite to the seeding density of 18 seeds m-1. The higher the seeding density, the largest was the plant stand, whereas the 23 mm seed obtained the best results and the same with the seeding density of 14 seeds m-1 that had a higher percentage of normal spacing. The densities of 14 and 18 seeds m-1 reflected in higher yields, being always superior to the 23 mm seeds.

The knapsack problem approach in solving partial hedging problems of options

En option är ett finansiellt kontrakt som ger dess innehavare en rättighet (men medför ingen skyldighet) att sälja eller köpa någonting (till exempel en aktie) till eller från säljaren av optionen till ett visst pris vid en bestämd tidpunkt i framtiden. Den som säljer optionen binder sig till att gå med på denna framtida transaktion ifall optionsinnehavaren längre fram bestämmer sig för att inlösa optionen. Säljaren av optionen åtar sig alltså en risk av att den framtida transaktion som optionsinnehavaren kan tvinga honom att göra visar sig vara ofördelaktig för honom. Frågan om hur säljaren kan skydda sig mot denna risk leder till intressanta optimeringsproblem, där målet är att hitta en optimal skyddsstrategi under vissa givna villkor. Sådana optimeringsproblem har studerats mycket inom finansiell matematik. Avhandlingen "The knapsack problem approach in solving partial hedging problems of options" inför en ytterligare synpunkt till denna diskussion: I en relativt enkel (ändlig och komplett) marknadsmodell kan nämligen vissa partiella skyddsproblem beskrivas som så kallade kappsäcksproblem. De sistnämnda är välkända inom en gren av matematik som heter operationsanalys. I avhandlingen visas hur skyddsproblem som tidigare lösts på andra sätt kan alternativt lösas med hjälp av metoder som utvecklats för kappsäcksproblem. Förfarandet tillämpas även på helt nya skyddsproblem i samband med så kallade amerikanska optioner.

Hofbauer cells morphology and density in placentas from normal and pathological gestations

PURPOSE: In placentas from uncomplicated pregnancies, Hofbauer cells either disappear or become scanty after the fourth to fifth month of gestation. Immunohistochemistry though, reveals that a high percentage of stromal cells belong to Hofbauer cells. The aim of this study was to investigate the changes in morphology and density of Hofbauer cells in placentas from normal and pathological pregnancies. METHODS: Seventy placentas were examined: 16 specimens from normal term pregnancies, 10 from first trimester's miscarriages, 26 from cases diagnosed with chromosomal abnormality of the fetus, and placental tissue specimens complicated with intrauterine growth restriction (eight) or gestational diabetes mellitus (10). A histological study of hematoxylin-eosin (HE) sections was performed and immunohistochemical study was performed using the markers: CD 68, Lysozyme, A1 Antichymotrypsine, CK-7, vimentin, and Ki-67. RESULTS: In normal term pregnancies, HE study revealed Hofbauer cells in 37.5% of cases while immunohistochemistry revealed in 87.5% of cases. In first trimester's miscarriages and in cases with prenatal diagnosis of fetal chromosomal abnormalities, both basic and immunohistochemical study were positive for Hofbauer cells. In pregnancies complicated with intrauterine growth restriction or gestational diabetes mellitus, a positive immunoreaction was observed in 100 and 70% of cases, respectively. CONCLUSIONS: Hofbauer cells are present in placental villi during pregnancy, but with progressively reducing density. The most specific marker for their detection seems to be A1 Antichymotrypsine. It is remarkable that no mitotic activity of Hofbauer cells was noticed in our study, as the marker of cellular multiplication Ki-67 was negative in all examined specimens.

Genetic characterization of Brazilian bovine viral diarrhea virus isolates by partial nucleotide sequencing of the 5'-UTR region

Nineteen isolates of bovine viral diarrhea virus (BVDV) from Brazil were genetically characterized through partial nucleotide sequencing and analysis of the 5'UTR region. The isolates were grouped as BVDV-1 (11/19), BVDV-2 (6/19) or "atypical" pestivirus (2/19). Among the BVDV-1, eight isolates were classified as subgenotype BVDV-1a, whereas most (4 out of 6) BVDV-2 belonged to subgenotype 2b. Two isolates from aborted fetuses were not classified into any genetic group, being considered atypical BVDVs. Genetic diversity among Brazilian BVDV isolates may be responsible for vaccination and diag-nostic failure and therefore may influence the control strategies for BVDV infection in the country.

Profile of cortisol, glycaemia, and blood parameters of American Bullfrog tadpoles Lithobates catesbeianus exposed to density and hypoxia stressors

The aim of this study was to evaluate alterations to the physiological profile (cortisol, glycaemia, and blood parameters) of Lithobates catesbeianus caused by the stressors density and hypoxia. The organisms were in the prometamorphosis stage and exposed to different tadpole densities: 1 tadpole/L (T1), 5 tadpoles/L (T2), and 10 tadpoles/L (T3) for 12 days. The blood was collected through the rupture of the caudal blood vessel and collected under normoxia (immediate collection) and hypoxia (after 15 minutes of air exposure) conditions. Cortisol levels rose on the fourth and eighth days of treatment and returned to basal levels by the end of the experiment. The stressor mechanisms tested did not affect glycaemia. White blood cells (total number of lymphocytes, neutrophils, and eosinophils) showed a significant difference at the twelfth day of the experiment when compared with the start of the experiment. We concluded that, under controlled conditions, a density of up to 10 tadpoles/L and air exposure for 15 minutes did not cause harmful physiological alterations during the experimental period. The answer to these stressors maybe was in another hormonal level (corticosterone).

Density of primary and secondary epidermal laminae of equine hoof

Differences in the microscopic morphology of the hoof in forelimbs and hindlimbs of horses have been scarcely reported in the literature, especially concerning the distribution of primary and secondary epidermal laminae in the different regions. This study aimed to determine the density of primary and secondary epidermal laminae in the hoof of horses. For this, it was used fore and hindlimbs of 16 adult mixed breed horses. With a cross section 0.5 cm above the sole, it was quantified the primary epidermal laminae in the regions of the toe, and of lateral and medial quarters. Fragments with about 1cm ³ were taken from the proximal, middle and distal thirds of the hooves, in the different regions, subjected to conventional histological techniques and examined with an optical microscope. Data were statistically analyzed in relation to the fore and hindlimbs and between their various regions. The density of primary epidermal laminae varied around the hoof circumference, with greater values in the hoof toe, which gradually decreased towards the bulb of the hoof, without difference between thoracic and pelvic limbs. The average density of the secondary epidermal laminae per primary epidermal lamina does not change around the circumference of the hoof. Our findings indicated that the density of epidermal laminae is not different between fore and hindlimbs. The variation in the density of primary epidermal laminae around the hoof seems to be part of an adaptive response to different stresses in each region. A better understanding of the structural morphology contributes to a better understanding of the diagnosis, pathophysiology, and treatment of disorders that affect the hoof.

Isolation and characterization of equine peripheral blood-derived multipotent mesenchymal stromal cells

The objective of the study was to isolate, cultivate and characterize equine peripheral blood-derived multipotent mesenchymal stromal cells (PbMSCs). Peripheral blood was collected, followed by the isolation of mononuclear cells using density gradient reagents, and the cultivation of adherent cells. Monoclonal mouse anti-horse CD13, mouse anti-horse CD44, and mouse anti-rat CD90 antibodies were used for the immunophenotypic characterization of the surface of the PbMSCs. These cells were also cultured in specific media for adipogenic and chondrogenic differentiation. There was no expression of the CD13 marker, but CD44 and CD90 were expressed in all of the passages tested. After 14 days of cell differentiation into adipocytes, lipid droplets were observed upon Oil Red O (ORO) staining. Twenty-one days after chondrogenic differentiation, the cells were stained with Alcian Blue. Although the technique for the isolation of these cells requires improvement, the present study demonstrates the partial characterization of PbMSCs, classifying them as a promising type of progenitor cells for use in equine cell therapy.

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Partial budget analysis of prepartum antimicrobial therapy and Escherichia coli J5 vaccination of dairy heifers and their effect on milk production and milk quality parameters

Abstract: This study aimed to determine whether prepartum antimicrobial and/or Escherichia coli J5 vaccination in dairy heifers influence the milk production, milk quality, and estimate their economic benefit. Thus, 33 dairy heifers were enrolled in four groups using a split-splot design. Groups were: (G1) prepartum antimicrobial infusion and vaccination with an E. coli J5 bacterin, (G2) prepartum antimicrobial infusion, (G3) vaccination with an E. coli J5 bacterin, and (G4) control heifers. Composite milk samples for somatic cell count, total bacteria count and milk composition were collected 15 days after calving and every 15 days until the end of the experiment. Bacteriological analysis was carried out at the end of study. The milk production and the incidence of clinical cases of mastitis, as well as the costs associated with them were recorded. The results demonstrate a reduction on clinical mastitis rates by preventive strategies, which implicated in lower volume of discarded milk (0.99, 1.01, 1.04 and 3.98% for G1, G2, G3 and G4, respectively) and higher economic benefit. Thus, in well-managed dairy herds the prevention of heifer mastitis by vaccination or antimicrobial therapy can reduce the amount of antimicrobials needed to treat clinical mastitis cases and the days of discarded milk.

Avaliação da deposição da calda de pulverização em função da densidade populacional de Brachiaria plantaginea, do volume e do ângulo de aplicação: effects of density, volume and spraying angle

O presente trabalho teve por objetivo avaliar a quantidade de calda de pulverização depositada nas folhas de Brachiaria plantaginea, em aplicações de pós-emergência precoce, em que se variou o volume de calda de pulverização, a densidade de plantas m-2 e o ângulo de posicionamento da ponta de pulverização na barra de aplicação. Para isso, foram conduzidos três experimentos em condições de laboratório. Nestes estudos, o volume de calda de pulverização foi obtido por meio da variação da velocidade de deslocamento de um veículo composto por plataforma e quatro rolamentos tracionados por um motor elétrico. Foi utilizada a ponta de pulverização XR Teejet 8001 EVS, na pressão de 241,4 kPa. O delineamento experimental utilizado foi o inteiramente casualizado, com cinco repetições. No primeiro experimento, os volumes utilizados foram de 1147,57; 860,68; 573,78; 459,02; 344,27; 229,51; 114,75; e 57,37 L ha-1 de calda de pulverização, com densidade de 600 plantas m-2. No segundo experimento foram estudadas as densidades de 300, 600, 900 e 1.200 plantas m-2; neste caso, utilizou-se o volume de 229,51 L ha-1 de calda de pulverização. No terceiro experimento avaliou-se o posicionamento do ângulo da ponta de pulverização na barra de aplicação e utilizou-se a densidade de 600 plantas m-2. Estudaram-se os ângulos de -30º, -15º, 90º, +15º e +30º e os volumes de calda de pulverização de 198,76; 221,69; 229,51; 221,69; e 198,76 L ha-1, respectivamente. Foram adotados sinais negativos para o sentido de deslocamento do veículo e sinais positivos para o sentido contrário ao deslocamento. As avaliações do depósito de calda de pulverização, na planta e no solo, foram feitas utilizando-se condutividade elétrica. A porcentagem de depósito de calda de pulverização nas plantas de B. plantaginea foi incrementada com a redução do volume de calda pulverizada por hectare. O depósito de calda por planta foi maior nas densidades maiores de plantas. O ângulo de posicionamento da ponta de pulverização na barra de aplicação incrementou o depósito de calda nas plantas de B. plantaginea, quando comparado com o ângulo de 90º.

Planting density of gliricidia when intercropped with corn for weed control

Reduced use of herbicides that cause environmental pollution problems is of great interest in modern agriculture. Soil mulching with gliricidia (Gliricidia sepium) branches does not have an allelopathic effect on corn, but decreases weed populations. The objective of this study was to evaluate the effects of gliricidia planting density, when grown as an intercrop, on weed control and corn yield parameters. A randomized block design with split-plots and ten replicates was adopted. Corn cultivars AG 1051 and BM 3061 were grown without hoeing, with two hoes (at 24 and 44 days after planting), and intercropped with gliricidia (planted simultaneously with corn, between crop rows, using two seedlings/pit, spaced at 30, 40, or 50 cm). Twenty-one weed species were found in the experimental area. Increased gliricidia planting density reduced weed biomass, but no difference was found between weed biomass in the intercrop and weed biomass in non-hoed corn. Gliricidia intercropped with corn, planted at a row spacing of 30 cm, did not significantly differ from hoed corn in most characteristics considered to evaluate green corn yield, although mean values were smaller. As to the number and weight of marketable green ears, reductions of 5% and 13%, respectively, were observed. Intercropping caused a 17% reduction in grain yield, reducing the losses (36%) observed in non-hoed corn by more than 50%. The highest green ear yield and grain yield values were obtained with two hoeings, while the lowest values were observed for non-hoed corn. The cultivars did not differ regarding green ear yield and grain yield.

Influence of corn sowing density and gliricidia intercropping on weed control

There is interest in the identification of the best seeding density for new corn hybrids and on reduced use of herbicides for weed control. The objective of this study was to evaluate the effects of seeding density (30, 50, 70, and 90 thousand plants ha-1) and weed control on green ear yield and grain yield in corn cultivar AG 1051. A completely randomized block design was adopted with split-plots (seeding densities assigned to plots) and ten replicates. Weed control was achieved by means of two hoeings and by planting corn intercropped with gliricidia (between corn rows, in pits spaced 0.3 m apart). A "no weeding"treatment was included as well. Increased seeding density increased the total number and weight of marketable green ears and decreased the biomass of both weeds and gliricidia. In non-weeded, intercropped and hoed plots, the maximum grain yield values achieved as seeding density increased were 7,881, 7,021, and 9,213 kg ha-1, respectively, obtained with populations of 67 thousand, 74 thousand, and 67 thousand plants per hectare, respectively. Intercropping did not control weeds (26 species) and provided weed growth, green ear yield, and grain yield (at the lowest densities) similar to those obtained without hoeing, except for total number of green ears, in which no influence of weed control was observed. At densities of 70 thousand and 90 thousand plants per hectare, grain yield with two hoeings was not different from yield values obtained without weeding or in the treatment intercropped with gliricidia, respectively, indicating that increased corn seeding density as well as gliricidiamay help to control weeds.

Density and sowing season of two Brachiaria species on the soybean culture

The aim of this study was to evaluate the growth and yield of soybean cultivar M-8766 in consortium with Brachiaria brizantha. BRS Piata and Brachiaria ruziziensis at different densities and sowing dates. The experimental design was randomized blocks with treatments arranged in a factorial 2 x 2 x 3 with four replications. Used as factors grass species (Brachiaria brizantha Piata and Brachiaria ruziziensis BRS) intercropped with soybean M-8766, sowing dates (12 and 24 days after soybean emergence) and three seeding rates (0, 5, 10 kg ha-1 of seed). At 71 days after soybean emergence were evaluated plant height, stem diameter, dry mass of leaves, stems and shoots, and 4 months after sowing determined the weight of 100 grains and soybean yield. The results showed that when seeded at a density of 10 kg ha-1 at 12 and 24 DAE soy, Brachiaria brizantha. BRS Piata caused reduction in yield in the order of 6.71% and 3.03% respectively, while the Brachiaria ruziziensis was one that caused a greater reduction in productivity in the order of 13.42 and 16.23%, respectively, of these values expression when considering the price of soybean sack. B. ruziziensis expressed less competitive with soybean. However, the large biomass production of this grass provides deployment system till the next harvest.