Sublimation of water ice mixed with silicates and tholins: Evolution of surface texture and reflectance spectra, with implications for comets

The surfaces of many objects in the Solar System comprise substantial quantities of water ice sometimes mixed with minerals and/or organic molecules. The sublimation of the ice changes the structural and optical properties of these objects. We present laboratory data on the evolution of the structure and the visible and near-infrared spectral reflectance of icy surface analogues of cometary ices, made of water ice, complex organic matter (tholins) and silicates, as they undergo sublimation under low temperature (<-70°C) and pressure (10-⁵mbar) conditions inside the SCITEAS simulation chamber. As the water ice sublimated, we observed in situ the formation of a porous sublimation lag deposit, or sublimation mantle, at the top of the ice. This mantle is a network of filaments made of the non-volatile particles. Organics or phyllosilicates grains, able to interact via stronger inter-particulate forces than olivine grains, can form a foam-like structure having internal cohesiveness, holding olivine grains together. As this mantle builds-up, the band depths of the sub-surface water ice are attenuated until complete extinction under only few millimeters of mantle. Optically thick sublimation mantles are mainly featureless in the near infrared. The absorption bands of the minerals present in the mantle are weak, or even totally absent if minerals are mixed with organics which largely dominate the VIS–NIR reflectance spectrum. During sublimation, ejections of large fragments of mantle, triggered by the gas flow, expose ice particles to the surface. The contrast of brightness between mantled and ice-exposed areas depends on the wavelength range and the dust/ice ratio considered. We describe how the chemical nature of the non-volatiles, the size of their particles, the way they are mixed with the ice and the dust/ice mass ratio influence the texture, activity and spectro-photometric properties of the sublimation mantles. These data provide useful references for interpreting remote-sensing observations of comets and also icy satellites or trans-neptunian objects.

Evaluation of PRESAGE® dosimeters for brachytherapy sources and the 3D dosimetry and characterization of the new AgX100 125I seed model

With continuous new improvements in brachytherapy source designs and techniques, method of 3D dosimetry for treatment dose verifications would better ensure accurate patient radiotherapy treatment. This study was aimed to first evaluate the 3D dose distributions of the low-dose rate (LDR) Amersham 6711 OncoseedTM using PRESAGE® dosimeters to establish PRESAGE® as a suitable brachytherapy dosimeter. The new AgX100 125I seed model (Theragenics Corporation) was then characterized using PRESAGE® following the TG-43 protocol. PRESAGE® dosimeters are solid, polyurethane-based, 3D dosimeters doped with radiochromic leuco dyes that produce a linear optical density response to radiation dose. For this project, the radiochromic response in PRESAGE® was captured using optical-CT scanning (632 nm) and the final 3D dose matrix was reconstructed using the MATLAB software. An Amersham 6711 seed with an air-kerma strength of approximately 9 U was used to irradiate two dosimeters to 2 Gy and 11 Gy at 1 cm to evaluate dose rates in the r=1 cm to r=5 cm region. The dosimetry parameters were compared to the values published in the updated AAPM Report No. 51 (TG-43U1). An AgX100 seed with an air-kerma strength of about 6 U was used to irradiate two dosimeters to 3.6 Gy and 12.5 Gy at 1 cm. The dosimetry parameters for the AgX100 were compared to the values measured from previous Monte-Carlo and experimental studies. In general, the measured dose rate constant, anisotropy function, and radial dose function for the Amersham 6711 showed agreements better than 5% compared to consensus values in the r=1 to r=3 cm region. The dose rates and radial dose functions measured for the AgX100 agreed with the MCNPX and TLD-measured values within 3% in the r=1 to r=3 cm region. The measured anisotropy function in PRESAGE® showed relative differences of up to 9% with the MCNPX calculated values. It was determined that post-irradiation optical density change over several days was non-linear in different dose regions, and therefore the dose values in the r=4 to r=5 cm regions had higher uncertainty due to this effect. This study demonstrated that within the radial distance of 3 cm, brachytherapy dosimetry in PRESAGE® can be accurate within 5% as long as irradiation times are within 48 hours.

Actividad antioxidante de los compuestos fenólicos contenidos en las semillas de la vid (vitis vinifera l.)

El propósito de este trabajo es obtener un antioxidante natural a partir de las semillas de uva (Vitis vinifera L.), para emplear en alimentos. Para ello se compararon distintos solventes para la extracción de fenoles de las semillas de la uva, de modo de obtener el extracto más concentrado en compuestos activos con la mínima degradación de su poder antioxidante durante el proceso de obtención. La concentración de fenoles totales de los extractos se determinó por el método Folin Ciocalteu. El poder reductor de los extractos se midió empleando el método de Oyaizu. Una vez seleccionado el solvente más adecuado para la extracción, se analizó la cinética de extracción, optimizando el tiempo de tratamiento. El extracto fue concentrado al vacío, y se veríficó la conservación del poder reductor en el extracto concentrado, por el método de Oyaizu. El extracto de semillas concentrado y sin concentrar se empleó en un sistema real sujeto a oxidación, tal como el jugo de manzanas. El grado de oxidación del jugo se midió por el método de Özoglu. El extracto concentrado fue deshidratado por secado en lecho de espuma y por liofilizado. En ambos casos se verificó el efecto del tratamiento de secado sobre el poder reductor. Finalmente, se evaluó la actividad antioxidante del extracto líquido concentrado de semillas de vid, respecto de otros antioxidantes comerciales como ácido ascórbico y dióxido de azufre. El sustrato oxidable fue el jugo de manzanas, y el grado de oxidación se midió por el método de Özoglu. El análisis estadístico de los datos se realizó mediante el análisis de la varianza; cuando no fue posible emplear el mencionado análisis, debido a que no se verificaban los supuestos básicos para su aplicación, se empleó la prueba de Kruskal –Wallis. En todos los casos, se utilizó el programa Statgraphics plus ®4.0. Para obtener un extracto antioxidante a partir de semillas de vid se utilizó una ex-tracción con agua a 90ºC, durante 4 horas. La relación sólido- líquido empleada fue de 1g de semillas enteras por 10 ml de solvente. El extracto obtenido presentaba una concentración de 12,587 mg de fenoles totales por gramo de semillas de uva extractadas y un poder reductor de 1,290 unidades. Como consecuencia del análisis de la cinética de extracción, el tiempo de tratamiento se redujo de 4 horas a 3 horas. La concentración del extracto se realizó al vacío a 60ºC, verificándose un aumen-to del poder reductor en el extracto concentrado, comprobado sobre jugo de manzanas. Comparando el extracto concentrado y el extracto sin concentrar se observa que la concentración de fenoles totales aumentó 29,57 veces, mientras que el poder reductor aumentó 37,39 veces. El deshidratado del extracto por medio del lecho de espuma permitió conservar el poder reductor del mismo, no ocurrió lo mismo en el deshidratado por liofilizado, donde se produjo un deterioro del poder reductor. Para un mismo contenido de fenoles totales agregado al jugo de manzanas, el ex-tracto líquido sin concentrar produjo un 28,4% de inhibición de la oxidación, mientras que el de extracto líquido concentrado produjo un 51,5 % de inhibición de la oxidación del jugo de manzanas. El extracto de semillas de vid, aplicado como antioxidante en jugo de manzanas, inhibió el desarrollo de la oxidación en un 31,51%, considerando 24 horas el tiempo de tratamiento. Este desempeño supera al ácido ascórbico, que en iguales condiciones, inhibió el desarrollo de la oxidación en un 2,6%. Pero en las condiciones de tra-bajo, el dióxido de azufre resulta mejor antioxidante que ambos, ya que logró inhibir el desarrollo de la oxidación en un 97,40 %.

Extracto de semillas de vid (Vitis vinifera L.) con actividad antioxidante : concentración, deshidratación y comparación con antioxidantes de uso comercial

Los objetivos de este trabajo fueron: 1) Evaluar un proceso de concentración y deshidratación de un extracto polifenólico de semillas de vid (Vitis vinifera L.). El proceso debía conservar el poder reductor del extracto. 2) Valorar la eficiencia del antioxidante obtenido por comparación con antioxidantes de uso habitual en un producto vegetal susceptible de ser oxidado, tal como el jugo de manzanas. El extracto de semillas de vid fue concentrado a 60°C en un concentrador rotativo al vacío de laboratorio. La concentración de los compuestos fenólicos fue determinada por el método de Folin-Ciocalteu modificado. La actividad antioxidante se determinó midiendo el poder reductor, por el método de Oyaizu. La oxidación del jugo de manzanas se determinó por el método de Özoglu. El extracto concentrado obtenido fue deshidratado por dos métodos: liofilización y secado en lecho de espuma. A igual concentración fenólica, el extracto concentrado mostró mayor capacidad antioxidante que el extracto simple. El extracto secado en lecho de espuma conservó la misma capacidad antioxidante que el extracto concentrado. El extracto liofilizado experimentó una pérdida significativa de la actividad antioxidante. El extracto concentrado de semillas de vid inhibió la oxidación del jugo de manzanas en un 31,51%, el ácido ascórbico en un 2,60% y el dióxido de azufre en un 97,40%.

Shipborne ocean color remote sensing

In this paper, modernized shipborne procedures are presented to collect and process above-water radiometry for remote sensing applications. A setup of five radiometers and a bidirectional camera system, which provides panoramic sea surface and sky images, is proposed for the collection of high-resolution radiometric quantities. Images from the camera system can be used to determine sky state and potential glint, whitecaps, or foam contamination. A peak in the observed remote sensing reflectance RRS spectra between 750-780 nm was typically found in spectra with relatively high surface reflected glint (SRG), which suggests this waveband could be a useful SRG indicator. Simplified steps for computing uncertainties in SRG corrected RRS are proposed and discussed. The potential of utilizing "unweighted multimodel averaging," which is the average of four or more common SRG correction models, is examined to determine the best approximation RRS. This best approximation RRS provides an estimate of RRS based on various SRG correction models established using radiative transfer simulations and field investigations. Applying the average RRS provides a measure of the inherent uncertainties or biases that result from a user subjectively choosing any one SRG correction model. Comparisons between inherent and apparent optical property derived observations were used to assess the robustness of the SRG multimodel averaging ap- proach. Correlations among the standard SRG models were completed to determine the degree of association or similarities between the SRG models. Results suggest that the choice of glint models strongly affects derived RRS values and can also influence the blue to green band ratios used for modeling biogeochemical parameters such as for chlorophyll a. The objective here is to present a uniform and traceable methodology for determining ship- borne RRS measurements and its associated errors due to glint correction and to ensure the direct comparability of these measurements in future investigations. We encourage the ocean color community to publish radiometric field measurements with matching and complete metadata in open access repositories.

Soft perches in an aviary system reduce incidence of keel bone damage in laying hens.

Keel bone fractures and deviations are one of the major welfare and health issues in commercial laying hens. In non-cage housing systems like aviaries, falls and collisions with perches and other parts of the housing system are assumed to be one of the main causes for the high incidence of keel bone damage. The objectives of this study were to investigate the effectiveness of a soft perch material to reduce keel bone fractures and deviations in white (Dekalb White) and brown laying hens (ISA Brown) kept in an aviary system under commercial conditions. In half of 20 pens, all hard, metal perches were covered with a soft polyurethane material. Palpation of 20 hens per pen was conducted at 18, 21, 23, 30, 38, 44 and 64 weeks of age. Production data including egg laying rate, floor eggs, mortality and feed consumption were collected over the whole laying period. Feather condition and body mass was assessed twice per laying period. The results revealed that pens with soft perches had a reduced number of keel bone fractures and deviations. Also, an interaction between hybrid and age indicated that the ISA hybrid had more fractured keel bones and fewer non-damaged keel bones compared with the DW hybrid at 18 weeks of age, a response that was reversed at the end of the experiment. This is the first study providing evidence for the effectiveness of a soft perch material within a commercial setting. Due to its compressible material soft perches are likely to absorb kinetic energy occurring during collisions and increase the spread of pressure on the keel bone during perching, providing a mechanism to reduce keel bone fractures and deviations, respectively. In combination with genetic selection for more resilient bones and new housing design, perch material is a promising tool to reduce keel bone damage in commercial systems.

Properties of aluminium nodules foamed with concentrated solar energy

Commercial aluminium foam filled structures and sandwich panels are available for structural applications. As alternative to these materials, small granular foamed pieces are proposed to fill structures as well as sandwich panels. On the present work, foam precursors are obtained by Powder Metallurgy (PM) route, using natural calcium carbonate as foaming agent instead of titanium hydride. Extruded precursor bars were cut into small pieces (around 4.5 mm long and 5mm in diameter). Foaming treatment was carried out on two different ways: electrical preheated furnace and by solar furnace. Foamed nodules presented a low cell size, density e.g. 0.67 g/cm3 to 0.88 g/cm3 and a height/diameter ratio between 0.72 and 0.84 as a function of precursor size. These properties depend on the foaming particle size, foaming cycle and precursor dimensions. Carbonate precursors are easily foamed by concentrated solar energy, due to the lower risk of cell collapse than with hydride precursors, resulting from cell stabilization by oxide skin formation into cells and a low degree of foamed nodules bonding.

Multi-criteria selection of structural adhesives to bond ABS parts obtained by rapid prototyping

One of the most used methods in rapidprototyping is Fused Deposition Modeling (FDM), which provides components with a reasonable strength in plastic materials such as ABS and has a low environmental impact. However, the FDM process exhibits low levels of surface finishing, difficulty in getting complex and/or small geometries and low consistency in “slim” elements of the parts. Furthermore, “cantilever” elements need large material structures to be supported. The solution of these deficiencies requires a comprehensive review of the three-dimensional part design to enhance advantages and performances of FDM and reduce their constraints. As a key feature of this redesign a novel method of construction by assembling parts with structuraladhesive joints is proposed. These adhesive joints should be designed specifically to fit the plastic substrate and the FDM manufacturing technology. To achieve this, the most suitable structuraladhesiveselection is firstly required. Therefore, the present work analyzes five different families of adhesives (cyanoacrylate, polyurethane, epoxy, acrylic and silicone), and, by means of the application of technical multi-criteria decision analysis based on the analytic hierarchy process (AHP), to select the structuraladhesive that better conjugates mechanical benefits and adaptation to the FDM manufacturing process

Desarrollo, análisis y caracterización de procesos de soldeo térmico de espumas de aluminio

Uno de los retos actuales aún pendiente de lograr trabajando con espumas de aluminio, es el desarrollo de métodos de unión fácilmente reproducibles a nivel industrial que permitan la unión de espumas de aluminio entre sí o con otros componentes tipo pletinas, para así poder fabricar piezas de mayor tamaño o con formas complejas, a la vez que se conserven las propiedades y características principales de las espumas de aluminio, tanto en la zona principal de unión o cordón, como en la interfase y zona afectada térmicamente, que se encuentran anexa. Los actuales procesos de unión más utilizados con espumas de aluminio, se basan principalmente en adhesivos y uniones mecánicas. Estas soluciones a priori válidas, añaden problemas técnicos a determinadas aplicaciones de las espumas que frenan la completa integración de estos materiales en un entorno de fabricación flexible y global. Por esta razón, los actuales procesos de producción de las espumas de aluminio se restringen a determinadas ofertas hechas a la medida del cliente, no pudiendo atender por falta de soluciones, a una gran parte del potencial mercado de estos materiales. En el presente trabajo de investigación se han desarrollado y caracterizado diferentes métodos de unión de espumas de aluminio, en configuración a tope y de espumas de aluminio con pletinas en configuración a solape, basados en procesos por soldeo térmico. One of the current challenges even pending of being achieved working with aluminium foams, is the development of easily reproducible methods at industrial level that allow the joint of aluminium foams between them or with other elements as for example aluminium plates for making bigger pieces or with more complex forms, remaining simultaneously in the weld bead the properties and main characteristics of aluminium foam, so much in the joint area or interface, since in the affected closer thermal zone. Currently, the most used joint processes for applying to aluminium foams are based mainly on adhesives and mechanical joins. These solutions initially valid, add technical problems to certain aluminium foams applications, which stop the complete integration of these materials in a more flexible and global manufacture environment. For this reason, current aluminium foam manufacturing processes are restricted to certain offers done to a specific customer requirement, not being able to attend for lack of available solutions, to a great potential market of these materials. In the present work, different joint methods between aluminium foams and between aluminium foams and plates for butt and lap configurations have been developed and characterized based on thermal welding processes.

Estudio del comportamiento mecánico de las espumas pulvimetalúrgicas de aluminio

Con este trabajo se pretende determinar la relación entre las características físicas y mecánicas y la estructura para espumas de aluminio de Al12Si y AA6061 obtenidas por pulvimetalurgia utilizando probetas prismáticas de dimensiones diecisiete por diecisiete por sesenta milímetros. De su estudio mecánico y de análisis de imagen se concluye que las probetas cuyas propiedades físicas y mecánicas están moderadamente por encima de la media poseen mayor número de poros medianos y paredes de poro más gruesas. Por el contrario, las propiedades resultan inferiores cuando se presentan estructuras con un mayor número de poros medianos. Aquellas espumas con estructuras obtenidas por una espumación incompleta presentan una menor porosidad y por ello mayores densidades. En aquellos casos donde la estructura presenta una elevada presencia de poros grandes, sus propiedades mecánicas disminuyen. ABSTRACT With this work we are trying to determine the relation between physical and mechanical characteristics and its structure, for Al12Si and AA6061 aluminium foams, obtained by podwer metallurgy. Aluminium foam samples with dimensions of seventeen per seventeen per sixty millimeters were used. After its mechanical and image analysis study, we conclude that samples whose physical and mechanical properties are moderately over the average, they have a major proportion of medium pores and thicker pore walls. Otherwise, properties result to be inferior when a major number of medium pores structures are presented. Those foam structures obtained with an incomplete foaming process show a lower porosity, and so higher densities. Also, properties decrease in those cases in which the structure presents a high presence of big pores.

Degradation in seawater of structural adhesives for hybrid fibre-metal laminated materials

The adhesives used for applications in marine environments are subject to particular chemical conditions, which are mainly characterised by an elevated chlorine ion content and intermittent wetting/drying cycles, among others.These conditions can limit the use of adhesives due to the degradation processes that they experience. In this work, the chemical degradation of two different polymers, polyurethane and vinylester, was studied in natural seawater under immersion for different periods of time.The diffusion coefficients and concentration profiles of water throughout the thickness of the adhesiveswere obtained.Microstructural changes in the polymer due to the action of water were observed by SEM, and the chemical degradation of the polymer was monitored with the Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC). The degradation of the mechanical properties of the adhesive was determined by creep tests withMixed Cantilever Beam (MCB) specimens at different temperatures. After 180 days of immersion of the specimens, it was concluded that the J-integral value (depending on the strain) implies a loss of stiffness of 51% and a decrease in the failure load of 59% for the adhesive tested.

Mode II fracture energy in the adhesive bonding of dissimilar substrates: carbon fibre composite to aluminium joints

The end-notched flexure (ENF) test calculates the value of mode II fracture energy in adhesive bonding between the substrates of same nature. Traditional methods of calculating fracture energy in the ENF test are not suitable in cases where the thickness of the adhesive is non-negligible compared with adherent thicknesses. To address this issue, a specific methodology for calculating mode II fracture energy has been proposed in this paper. To illustrate the applicability of the proposed method, the fracture energy was calculated by the ENF test for adhesive bonds between aluminium and a composite material, which considered two different types of adhesive (epoxy and polyurethane) and various surface treatments. The proposed calculation model provides higher values of fracture energy than those obtained from the simplified models that consider the adhesive thickness to be zero, supporting the conclusion that the calculation of mode II fracture energy for adhesives with non-negligible thickness relative to their adherents should be based on mathematical models, such as the method proposed in this paper, that incorporate the influence of this thickness.

MRI and Bidimensional relaxometry sequences for macro and microstructure assessment in food models.

Physico-chemical and organoleptic characteristics of food depend largely on the microscopic level distribution of gases and water, and connectivity and mobility through the pores. Microstructural characterization of food can be accomplished by Magnetic Resonance Imaging (MRI) and Nuclear Magnetic Spectroscopy (NMR) combined with the application of methods of dissemination and multidimensional relaxometry. In this work, funded by the EC Project InsideFood, several artificial food models, based on foams and gels were studied using MRI and 2D relaxometry. Two different kinds of foams were used: a sugarless and a sugar foam. Then, a half of a syringe was filled with the sugarless foam and the other half with the sugar foam. Then, MRI and NMR experiments were performed and the sample evolution was observed along 3 days in order to quantify macrostructural changes through proton density images and microstructural ones using T1T2 maps, using an inversion CPMG sequence. On the proton density images it may be seen that after 16 hours it was possible to differentiate the macrostructural changes, as the apparition of free water due to a syneresis phenomenon. On the interface it can be seen a brighter area after 16 hours, due to the occurrence of free water. Moreover, thanks to the bidimensional relaxometry (T1-T2) it was possible to differentiate among microscopic changes. Differences between the pores size can be observed as well as the microstructure evolution after 30.5 hours, as a consequence differences are shown on free water redistribution through larger pores and capillarity phenomena between both foams.

Diseño y comportamiento de uniones estructurales mecánicas y adhesivas. Condiciones superficiales y operacionales

Las uniones estructurales mecánicas y adhesivas requieren la combinación de un número importante de parámetros para la obtención de la continuidad estructural que exigen las condiciones de diseño. Las características de las uniones presentan importantes variaciones, ligadas a las condiciones de ejecución, tanto en uniones mecánicas como especialmente en uniones adhesivas y mixtas (unión mecánica y adhesiva, también conocidas como uniones híbridas). Las propiedades mecánicas de las uniones adhesivas dependen de la naturaleza y propiedades de los adhesivos y también de muchos otros parámetros que influyen directamente en el comportamiento de estas uniones. Algunos de los parámetros más significativos son: el acabado superficial de los materiales, área y espesor de la capa adhesiva, diseño adecuado, secuencia de aplicación, propiedades químicas de la superficie y preparación de los sustratos antes de aplicar el adhesivo. Los mecanismos de adhesión son complejos. En general, cada unión adhesiva solo puede explicarse considerando la actuación conjunta de varios mecanismos de adhesión. No existen adhesivos universales para un determinado material o aplicación, por lo que cada pareja sustrato-adhesivo requiere un particular estudio y el comportamiento obtenido puede variar, significativamente, de uno a otro caso. El fallo de una junta adhesiva depende del mecanismo cohesión-adhesión, ligado a la secuencia y modo de ejecución de los parámetros operacionales utilizados en la unión. En aplicaciones estructurales existen un número muy elevado de sistemas de unión y de posibles sustratos. En este trabajo se han seleccionado cuatro adhesivos diferentes (cianoacrilato, epoxi, poliuretano y silano modificado) y dos procesos de unión mecánica (remachado y clinchado). Estas uniones se han aplicado sobre chapas de acero al carbono en diferentes estados superficiales (chapa blanca, galvanizada y prepintada). Los parámetros operacionales analizados han sido: preparación superficial, espesor del adhesivo, secuencia de aplicación y aplicación de presión durante el curado. Se han analizado tanto las uniones individuales como las uniones híbridas (unión adhesiva y unión mecánica). La combinación de procesos de unión, sustratos y parámetros operacionales ha dado lugar a la preparación y ensayo de más de mil muestras. Pues, debido a la dispersión de resultados característica de las uniones adhesivas, para cada condición analizada se han ensayado seis probetas. Los resultados obtenidos han sido: El espesor de adhesivo utilizado es una variable muy importante en los adhesivos flexibles, donde cuanto menor es el espesor del adhesivo mayor es la resistencia mecánica a cortadura de la unión. Sin embargo en los adhesivos rígidos su influencia es mucho menor. La naturaleza de la superficie es fundamental para una buena adherencia del adhesivo al substrato, que repercute en la resistencia mecánica de la unión. La superficie que mejor adherencia presenta es la prepintada, especialmente cuando existe una alta compatibilidad entre la pintura y el adhesivo. La superficie que peor adherencia tiene es la galvanizada. La secuencia de aplicación ha sido un parámetro significativo en las uniones híbridas, donde los mejores resultados se han obtenido cuando se aplicaba primero el adhesivo y la unión mecánica se realizaba antes del curado del adhesivo. La aplicación de presión durante el curado se ha mostrado un parámetro significativo en los adhesivos con poca capacidad para el relleno de la junta. En los otros casos su influencia ha sido poco relevante. El comportamiento de las uniones estructurales mecánicas y adhesivas en cuanto a la resistencia mecánica de la unión puede variar mucho en función del diseño de dicha unión. La resistencia mecánica puede ser tan grande que falle antes el substrato que la unión. Las mejores resistencias se consiguen diseñando las uniones con adhesivo cianoacrilato, eligiendo adecuadamente las condiciones superficiales y operacionales, por ejemplo chapa blanca aplicando una presión durante el curado de la unión. La utilización de uniones mixtas aumenta muy poco o nada la resistencia mecánica, pero a cambio proporciona una baja dispersión de resultados, siendo destacable para la superficie galvanizada, que es la que presenta peor reproducibilidad cuando se realizan uniones sólo con adhesivo. Las uniones mixtas conducen a un aumento de la deformación antes de la rotura. Los adhesivos dan rotura frágil y las uniones mecánicas rotura dúctil. La unión mixta proporciona ductilidad a la unión. Las uniones mixtas también pueden dar rotura frágil, esto sucede cuando la resistencia del adhesivo es tres veces superior a la resistencia de la unión mecánica. Las uniones híbridas mejoran la rigidez de la junta, sobre todo se aprecia un aumento importante en las uniones mixtas realizadas con adhesivos flexibles, pudiendo decirse que para todos los adhesivos la rigidez de la unión híbrida es superior. ABSTRACT The mechanical and adhesive structural joints require the combination of a large number of parameters to obtain the structural continuity required for the design conditions. The characteristics of the junctions have important variations, linked to performance conditions, in mechanical joints as particular in mixed adhesive joints (mechanical and adhesive joints, also known as hybrid joints). The mechanical properties of the adhesive joints depend of the nature and properties of adhesives and also of many other parameters that directly influence in the behavior of these joints. Some of the most significant parameters are: the surface finished of the material, area and thickness of the adhesive layer, suitable design, and application sequence, chemical properties of the surface and preparation of the substrate before applying the adhesive. Adhesion mechanisms are complex. In general, each adhesive joint can only be explained by considering the combined action of several adhesions mechanisms. There aren’t universal adhesives for a given material or application, so that each pair substrate-adhesive requires a particular study and the behavior obtained can vary significantly from one to another case. The failure of an adhesive joint depends on the cohesion-adhesion mechanism, linked to the sequence and manner of execution of the operational parameters used in the joint. In the structural applications, there are a very high number of joining systems and possible substrates. In this work we have selected four different adhesives (cyanoacrylate, epoxy, polyurethane and silano modified) and two mechanical joining processes (riveting and clinching). These joints were applied on carbon steel with different types of surfaces (white sheet, galvanized and pre-painted). The operational parameters analyzed were: surface preparation, thickness of adhesive, application sequence and application of pressure during curing. We have analyzed individual joints both as hybrid joints (adhesive joint and mechanical joint). The combination of joining processes, substrates and operational parameters has resulted in the preparation and testing of over a thousand specimens. Then, due to the spread of results characteristic of adhesive joints, for each condition analyzed we have tested six samples. The results have been: The thickness of adhesive used is an important variable in the flexible adhesives, where the lower the adhesive thickness greater the shear strength of the joint. However in rigid adhesives is lower influence. The nature of the surface is essential for good adherence of the adhesive to the substrate, which affects the shear strength of the joint. The surface has better adherence is preprinted, especially when there is a high compatibility between the paint and the adhesive. The surface which has poor adherence is the galvanized. The sequence of application has been a significant parameter in the hybrid junctions, where the best results are obtained when applying first the adhesive and the mechanical joint is performed before cured of the adhesive. The application of pressure during curing has shown a significant parameter in the adhesives with little capacity for filler the joint. In other cases their influence has been less relevant. The behavior of structural mechanical and adhesive joints in the shear strength of the joint can vary greatly depending on the design of such a joint. The shear strength may be so large that the substrate fails before the joint. The best shear strengths are achieved by designing the junctions with cyanoacrylate adhesive, by selecting appropriately the surface and operating conditions, for example by white sheet applying a pressure during curing of the joint. The use of hybrid joints no increase shear strength, but instead provides a low dispersion of results, being remarkable for the galvanized surface, which is the having worst reproducibility when performed bonded joints. The hybrid joints leading to increased deformation before rupture. The joints witch adhesives give brittle fracture and the mechanics joints give ductile fracture. Hybrid joint provides ductility at the joint. Hybrid joint can also give brittle fracture, this happens when the shear strength of the adhesive is three times the shear strength of the mechanical joint. The hybrid joints improve stiffness of joint, especially seen a significant increase in hybrid joints bonding with flexible adhesives, can be said that for all the adhesives, the hybrid junction stiffness is higher.