Review of correlations between SPT N and shear modulus: A new correlation applicable to any region

A low strain shear modulus plays a fundamental role in earthquake geotechnical engineering to estimate the ground response parameters for seismic microzonation. A large number of site response studies are being carried out using the standard penetration test (SPT) data, considering the existing correlation between SPT N values and shear modulus. The purpose of this paper is to review the available empirical correlations between shear modulus and SPT N values and to generate a new correlation by combining the new data obtained by the author and the old available data. The review shows that only few authors have used measured density and shear wave velocity to estimate shear modulus, which were related to the SPT N values. Others have assumed a constant density for all the shear wave velocities to estimate the shear modulus. Many authors used the SPT N values of less than 1 and more than 100 to generate the correlation by extrapolation or assumption, but practically these N values have limited applications, as measuring of the SPT N values of less than 1 is not possible and more than 100 is not carried out. Most of the existing correlations were developed based on the studies carried out in Japan, where N values are measured with a hammer energy of 78%, which may not be directly applicable for other regions because of the variation in SPT hammer energy. A new correlation has been generated using the measured values in Japan and in India by eliminating the assumed and extrapolated data. This correlation has higher regression coefficient and lower standard error. Finally modification factors are suggested for other regions, where the hammer energy is different from 78%. Crown Copyright (C) 2012 Published by Elsevier Ltd. All rights reserved.

Characterisation of microstructure and evaluation of optical and EPR properties of superhydrophobic copper dodecanoate films

Copper dodecanoate films prepared by emulsion method exhibit superhydrophobic property with water contact angle of 155 degrees and sliding angle of <2 degrees. The films have been characterised by using X-ray diffraction, field emission scanning electron microscopy and Fourier transform infrared spectroscopy techniques. Surface microstructure of copper dodecanoate consists of numerous microscale papillas of about 6-12 mu m in length with a diameter in the range of 360-700 nm. The superhydrophobicity of the films is due to their dual micronano surface morphology. The wetting behaviour of the film surface was studied by a simple water immersion test. The results show that copper dodecanoate film retained superhydrophobic property even after immersing in water for about 140 h. The optical absorption spectrum exhibits two broadbands centred at 388 and 630 nm that have been assigned to B-2(1g) -> E-2(g) and B-2(1g) -> B-2(2g) transitions of Cu2+ ions, respectively. The electron paramagnetic resonance spectrum exhibits two resonance signals with effective g values at g(parallel to)approximate to 2.308 and g(perpendicular to) approximate to 2.071, which suggests that the unpaired electron occupies d(x2-y2) orbital in the ground state. Copyright (C) 2011 John Wiley & Sons, Ltd.

Ultrasonic Wave Dispersion Characteristics of Fluid-Filled Single-Walled Carbon Nanotubes Based on Nonclassical Shell Model

In this paper, ultrasonic wave propagation analysis in fluid filled single-walled carbon nanotube (SWCNT) is studied using nonlocal elasticity theory. The SWCNT is modeled using Flugge's shell theory, with the wall having axial, circumferential and radial degrees of freedom and also including small scale effects. The fluid inside the SWCNT is assumed as water. Nonlocal governing equations for this system are derived and wave propagation analysis is also carried out. The presence of fluid in SWCNT alters the ultrasonic wave dispersion behavior. The wavenumber and wave velocity are smaller in presence of fluid as compared to the empty SWCNT. The nonlocal elasticity calculation shows that the wavenumber tends to reach the continuum limit at certain frequencies and the corresponding wave velocity tends to zero at those frequencies indicating localization and stationary behavior. It has been shown that the circumferential. waves will propagate non-dispersively at higher frequencies in nonlocality. The magnitudes of wave velocities of circumferential waves are smaller in nonlocal elasticity as compared to local elasticity. We also show that the cut-off frequency depend on the nonlocal scaling parameter and also on the density of the fluid inside the SWCNT, and the axial wavenumber, as the fluid becomes denser the cut-off frequency decreases. The effect of axial wavenumber on the ultrasonic wave behavior in SWCNTS filled with water is also discussed.

Cyclopentac]thiophene oligomers based solution processable D-A copolymers and their application as FET materials

Two new solution processable, low band gap donor-acceptor (D-A) copolymers (P1 and P2) comprising a cyclopentac] thiophene (CPT) based oligomers as donors and benzoc]1,2,5] selenadiazole (BDS) and 2-dodecyl1,2,3]-benzotriazole (BTAz) as acceptors were synthesized and characterized and their field effect transistor properties were studied. The internal charge transfer interaction between the electron-donating CPT based oligothiophene and the electron-accepting BDS or BTAz unit effectively reduces the band gap in polymers to 1.3 and 1.66 eV with low lying highest occupied molecular orbital (HOMO). The absorption spectrum of P1 was found to be more red shifted than that of P2 because of incorporation of the more electron-withdrawing BDS unit. The color of neutral P1 was found to be green in both solution and film states with two major bands in the absorption spectra; however, neutral P2 revealed one dominant absorption exhibiting red color in both solution and film state which could be attributed to the less electron-withdrawing effect of the BTAz unit. The polymers were further characterized by GPC, TGA, DSC and cyclic voltammetry. P1 and P2 exhibited charge carrier mobilities as high as 9 x 10(-3) cm(2) V-1 s(-1) and 2.56 x 10(-3) cm 2 V-1 s(-1), respectively with the current on/off ratio (I-on/I-off) in the order of 10(2).

Guided Wave based Damage Detection in a Composite T-joint using 3D Scanning Laser Doppler Vibrometer

Composite T-joints are commonly used in modern composite airframe, pressure vessels and piping structures, mainly to increase the bending strength of the joint and prevents buckling of plates and shells, and in multi-cell thin-walled structures. Here we report a detailed study on the propagation of guided ultrasonic wave modes in a composite T-joint and their interactions with delamination in the co-cured co-bonded flange. A well designed guiding path is employed wherein the waves undergo a two step mode conversion process, one is due to the web and joint filler on the back face of the flange and the other is due to the delamination edges close to underneath the accessible surface of the flange. A 3D Laser Doppler Vibrometer is used to obtain the three components of surface displacements/velocities of the accessible face of the flange of the T-joint. The waves are launched by a piezo ceramic wafer bonded on to the back surface of the flange. What is novel in the proposed method is that the location of any change in material/geometric properties can be traced by computing a frequency domain power flow along a scan line. The scan line can be chosen over a grid either during scan or during post-processing of the scan data off-line. The proposed technique eliminates the necessity of baseline data and disassembly of structure for structural interrogation.

About the transparent electrode of the organic photovoltaic cells

Electrodes and the nature of their contact with organic materials play a crucial role in the realization of efficient optoelectronic components. Whether the injection (organic light-emitting diodes - OLEDs) or collection (organic photovoltaic cells - OPV cells) of carriers, contacts must be as efficient as possible. To do this, it is customary to refer to electrode surface treatment and/or using a buffer layer all things to optimize the contact. Efficiency of organic photovoltaic cells based on organic electron donor/organic electron acceptor junctions can be strongly improved when the transparent conductive anode is coated with a buffer layer (ABL). We show that an ultra-thin gold (0.5 nm) or a thin molybdenum oxide (3-5 nm) can be used as efficient ABL. However, the effects of these ABL depend on the highest occupied molecular orbital (HOMO) of different electron donors of the OPV cells. The results indicate that, in the case of metal ABL, a good matching between the work function of the anode and the highest occupied molecular orbital of the donor material is the major factor limiting the hole transfer efficiency. Indeed, gold is efficient as ABL only when the HOMO of the organic donor is close to its work function Phi(Au). MoO3 has a wider field of application as ABL than gold. The role of the oxide is not so clearly understood than that of Au, different models proposed to interpret the experimental results are discussed.

Junction between surfaces of two topological insulators

We study the properties of a line junction which separates the surfaces of two three-dimensional topological insulators. The velocities of the Dirac electrons on the two surfaces may be unequal and may even have opposite signs. For a time-reversal invariant system, we show that the line junction is characterized by an arbitrary parameter alpha which determines the scattering from the junction. If the surface velocities have the same sign, we show that there can be edge states which propagate along the line junction with a velocity and spin orientation which depend on alpha and the ratio of the velocities. Next, we study what happens if the two surfaces are at an angle phi with respect to each other. We study the scattering and differential conductance through the line junction as functions of phi and alpha. We also find that there are edge states which propagate along the line junction with a velocity and spin orientation which depend on phi. Finally, if the surface velocities have opposite signs, we find that the electrons must transmit into the two-dimensional interface separating the two topological insulators.

Nonlinear Refraction and Two-Photon Absorption in Dense 2Bi(2)O(3)-B2O3 Glasses

High density transparent glasses (7.86 g/cc) were fabricated in the 2Bi(2)O(3)-B2O3 (BBO) system. Optical band gap of the obtained glasses was found to be 2.6eV. The refractive index measured for these glasses was 2.25 +/- 0.05 at lambda=543 nm. Nonlinear refraction and absorption studies were carried out on the BBO glasses using z-scan technique a lambda=532 nm of 10 ns pulse width. The nonlinear refractive index obtained was n(2)=12.1x10(-14) cm(2)/W and nonlinear absorption coefficient was beta=15.2 cm/GW. The n(2) and beta values of the BBO glasses were large compared to the other reported high index bismuth based oxide glass systems in the literature. These were attributed to the high density, high linear refractive index, low band gap and two photon absorption associated with these glasses. The electronic origin of large nonlinearities was discussed based on bond-orbital theory.

Evidence of nanoscale structural phase separation in large bandwidth La0.2Sr0.8MnO3

We have investigated the structural evolution of La0.2Sr0.8MnO3 using temperature dependent high resolution synchrotron x-ray diffraction technique. In a wide temperature range, La0.2Sr0.8MnO3 reveals nanoscale structural inhomogeneity consisting of cubic and tetragonal phases. The present results suggest that domains of nanometer size of the tetragonal (low temperature) phase start nucleating in the cubic (high temperature) phase even above the Neel temperature (T-N). The tetragonal phase fraction increases substantially below T-N. Detailed analysis suggests that the twinned phase is tetragonal, orbital ordered, and insulating. At temperatures below 170 K, a small amount of the cubic phase is retained. The present results reveal the significance of the connectivity between the nanoscale structural phase separation with the physical properties.

A new diketopyrrolopyrrole-based co-polymer for ambipolar field-effect transistors and solar cells

A new thieno3,2-b]thiophenediketopyrrolopyrrole-benzo1,2-b:4,5-b']dithio phene based narrow optical gap co-polymer (PTTDPP-BDT) has been synthesized and characterized for field-effect transistors and solar cells. In field-effect transistors the polymer exhibited ambipolar charge transport behaviour with maximum hole and electron mobilities of 10(-3) cm(2) V-1 s(-1) and 10(-5) cm(2)V(-1) s(-1), respectively. The respectable charge transporting properties of the polymer were consistent with X-ray diffraction measurements that showed close molecular packing in the solid state. The difference in hole and electron mobilities was explained by density functional theory calculations, which showed that the highest occupied molecular orbital was delocalized along the polymer backbone with the lowest unoccupied molecular orbital localized on the bis(thieno3,2-b]thiophene)diketopyrrolopyrrole units. Bulk heterojunction photovoltaic devices with the fullerene acceptor PC70BM were fabricated and delivered a maximum conversion efficiency of 3.3% under AM1.5G illumination. (C) 2012 Elsevier B.V. All rights reserved.

Large nonlinear refraction and two photon absorption in ferroelectric Bi2VO5.5 thin films

Ferroelectric c-oriented Bi2VO5.5 (BVO) thin films (thickness approximate to 300 nm) were fabricated by pulsed laser deposition on corning glass substrates. Nonlinear refractive index (n(2)) and two photon absorption coefficient (beta) were measured by Z-scan technique at 532 nm wavelength delivering pulses with 10 ns duration. Relatively large values of n(2) = 2.05 +/- 0.2 x 10(-10) cm(2)/W and beta = 9.36 +/- 0.3 cm/MW were obtained for BVO thin films. Origin of the large optical nonlinearities in BVO thin films was discussed based on bond-orbital theory of transition metal oxides. (c) 2012 Elsevier B.V. All rights reserved.

Study of terahertz wave propagation properties in nanoplates with surface and small-scale effects

In macroscopic and even microscopic structural elements, surface effects can be neglected and classical theories are sufficient. As the structural size decreases towards the nanoscale regime, the surface-to-bulk energy ratio increases and surface effects must be taken into account. In the present work, the terahertz wave dispersion characteristics of a nanoplate are studied with consideration of the surface effects as well as the nonlocal small-scale effects. Nonlocal elasticity theory of plate is used to derive the general differential equation based on equilibrium approach to include those scale effects. Scale and surface property dependent wave characteristic equations are obtained via spectral analysis. For the present study the material properties of an anodic alumina with crystallographic of < 111 > direction are considered. The present analysis shows that the effect of surface properties on the flexural waves of nanoplates is more significant. It can be found that the flexural wavenumbers with surface effects are high as compared to that without surface effects. The scale effects show that the wavenumbers of the flexural wave become highly non-linear and tend to infinite at certain frequency. After that frequency the wave will not propagate and the corresponding wave velocities tend to zero at that frequency (escape frequency). The effects of surface stresses on the wave propagation properties of nanoplate are also captured in the present work. (C) 2012 Elsevier Ltd. All rights reserved.

Monsoon circulation interaction with Western Ghats orography under changing climate - Projection by a 20-km mesh AGCM

In this study, the authors have investigated the likely future changes in the summer monsoon over the Western Ghats (WG) orographic region of India in response to global warming, using time-slice simulations of an ultra high-resolution global climate model and climate datasets of recent past. The model with approximately 20-km mesh horizontal resolution resolves orographic features on finer spatial scales leading to a quasi-realistic simulation of the spatial distribution of the present-day summer monsoon rainfall over India and trends in monsoon rainfall over the west coast of India. As a result, a higher degree of confidence appears to emerge in many aspects of the 20-km model simulation, and therefore, we can have better confidence in the validity of the model prediction of future changes in the climate over WG mountains. Our analysis suggests that the summer mean rainfall and the vertical velocities over the orographic regions of Western Ghats have significantly weakened during the recent past and the model simulates these features realistically in the present-day climate simulation. Under future climate scenario, by the end of the twenty-first century, the model projects reduced orographic precipitation over the narrow Western Ghats south of 16A degrees N that is found to be associated with drastic reduction in the southwesterly winds and moisture transport into the region, weakening of the summer mean meridional circulation and diminished vertical velocities. We show that this is due to larger upper tropospheric warming relative to the surface and lower levels, which decreases the lapse rate causing an increase in vertical moist static stability (which in turn inhibits vertical ascent) in response to global warming. Increased stability that weakens vertical velocities leads to reduction in large-scale precipitation which is found to be the major contributor to summer mean rainfall over WG orographic region. This is further corroborated by a significant decrease in the frequency of moderate-to-heavy rainfall days over WG which is a typical manifestation of the decrease in large-scale precipitation over this region. Thus, the drastic reduction of vertical ascent and weakening of circulation due to `upper tropospheric warming effect' predominates over the `moisture build-up effect' in reducing the rainfall over this narrow orographic region. This analysis illustrates that monsoon rainfall over mountainous regions is strongly controlled by processes and parameterized physics which need to be resolved with adequately high resolution for accurate assessment of local and regional-scale climate change.

Intermolecular charge transfer and vibrational analysis of hydrogen bonding in acetazolamide

In the present work the structural and spectral characteristics of acetazolamide have been studied by methods of infrared, Raman spectroscopy and quantum chemistry. Electrostatic potential surface, optimized geometry, harmonic vibrational frequencies, infrared intensities and activities of Raman scattering were calculated by density functional theory (DFT) employing B3LYP with complete relaxation in the potential energy surface using 6-311++G(d,p) basis set. Based on these results, we have discussed the correlation between the vibrational modes and the structure of the dimers of acetazolamide. The calculated vibrational spectra of three dimers of acetazolamide have been compared with observed spectra, and the assignment of observed bands was carried out using potential energy distribution. The observed spectra agree well with the values computed from the OFT. A comparison of observed and calculated vibrational spectra clearly shows the effect of hydrogen bonding. The frequency shifts observed for the different dimers are in accord with the hydrogen bonding in acetazolamide. Natural bond orbital (NBO) analyses reflect the charge transfer interaction in the individual hydrogen bond units and the stability of different dimers of acetazolamide. (C) 2012 Elsevier B.V. All rights reserved.

Acoustic and optical phonon dynamics from femtosecond time-resolved optical spectroscopy of the superconducting iron pnictide Ca(Fe0.944Co0.056)(2)As-2

We report the temperature evolution of coherently excited acoustic and optical phonon dynamics in the superconducting iron pnictide single crystal Ca(Fe0.944Co0.056)(2)As-2 across the spin density wave transition at T-SDW similar to 85 K and the superconducting transition at T-SC similar to 20 K. The strain pulse propagation model applied to the generation of the acoustic phonons yields the temperature dependence of the optical constants, and longitudinal and transverse sound velocities in the temperature range from 3.1 K to 300 K. The frequency and dephasing times of the phonons show anomalous temperature dependence below T-SC indicating a coupling of these low-energy excitations with the Cooper-pair quasiparticles. A maximum in the amplitude of the acoustic modes at T similar to 170 is seen, attributed to spin fluctuations and strong spin-lattice coupling before T-SDW. Copyright (c) EPLA, 2012