Microstructure control and iodine doping of bismuth telluride

On the materials scale, thermoelectric efficiency is defined by the dimensionless figure of merit zT. This value is made up of three material components in the form zT = Tα²/ρκ, where α is the Seebeck coefficient, ρ is the electrical resistivity, and κ is the total thermal conductivity. Therefore, in order to improve zT would require the reduction of κ and ρ while increasing α. However due to the inter-relation of the electrical and thermal properties of materials, typical routes to thermoelectric enhancement come in one of two forms. The first is to isolate the electronic properties and increase α without negatively affecting ρ. Techniques like electron filtering, quantum confinement, and density of states distortions have been proposed to enhance the Seebeck coefficient in thermoelectric materials. However, it has been difficult to prove the efficacy of these techniques. More recently efforts to manipulate the band degeneracy in semiconductors has been explored as a means to enhance α.

The other route to thermoelectric enhancement is through minimizing the thermal conductivity, κ. More specifically, thermal conductivity can be broken into two parts, an electronic and lattice term, κ_e and κ_l respectively. From a functional materials standpoint, the reduction in lattice thermal conductivity should have a minimal effect on the electronic properties. Most routes incorporate techniques that focus on the reduction of the lattice thermal conductivity. The components that make up κ_l (κ_l = 1/3Cνl) are the heat capacity (C), phonon group velocity (ν), and phonon mean free path (l). Since the difficulty is extreme in altering the heat capacity and group velocity, the phonon mean free path is most often the source of reduction.

Past routes to decreasing the phonon mean free path has been by alloying and grain size reduction. However, in these techniques the electron mobility is often negatively affected because in alloying any perturbation to the periodic potential can cause additional adverse carrier scattering. Grain size reduction has been another successful route to enhancing zT because of the significant difference in electron and phonon mean free paths. However, grain size reduction is erratic in anisotropic materials due to the orientation dependent transport properties. However, microstructure formation in both equilibrium and nonequilibrium processing routines can be used to effectively reduce the phonon mean free path as a route to enhance the figure of merit.

This work starts with a discussion of several different deliberate microstructure varieties. Control of the morphology and finally structure size and spacing is discussed at length. Since the material example used throughout this thesis is anisotropic a short primer on zone melting is presented as an effective route to growing homogeneous and oriented polycrystalline material. The resulting microstructure formation and control is presented specifically in the case of In₂Te₃-Bi₂Te₃ composites and the transport properties pertinent to thermoelectric materials is presented. Finally, the transport and discussion of iodine doped Bi₂Te₃ is presented as a re-evaluation of the literature data and what is known today.

An economic air pollution control model-application : photochemical smog in Los Angeles County in 1975

An economic air pollution control model, which determines the least cost of reaching various air quality levels, is formulated. The model takes the form of a general, nonlinear, mathematical programming problem. Primary contaminant emission levels are the independent variables. The objective function is the cost of attaining various emission levels and is to be minimized subject to constraints that given air quality levels be attained.

The model is applied to a simplified statement of the photochemical smog problem in Los Angeles County in 1975 with emissions specified by a two-dimensional vector, total reactive hydrocarbon, (RHC), and nitrogen oxide, (NO_x), emissions. Air quality, also two-dimensional, is measured by the expected number of days per year that nitrogen dioxide, (NO₂), and mid-day ozone, (O₃), exceed standards in Central Los Angeles.

The minimum cost of reaching various emission levels is found by a linear programming model. The base or "uncontrolled" emission levels are those that will exist in 1975 with the present new car control program and with the degree of stationary source control existing in 1971. Controls, basically "add-on devices", are considered here for used cars, aircraft, and existing stationary sources. It is found that with these added controls, Los Angeles County emission levels [(1300 tons/day RHC, 1000 tons /day NO_x) in 1969] and [(670 tons/day RHC, 790 tons/day NO_x) at the base 1975 level], can be reduced to 260 tons/day RHC (minimum RHC program) and 460 tons/day NO_x (minimum NO_x program).

"Phenomenological" or statistical air quality models provide the relationship between air quality and emissions. These models estimate the relationship by using atmospheric monitoring data taken at one (yearly) emission level and by using certain simple physical assumptions, (e. g., that emissions are reduced proportionately at all points in space and time). For NO₂, (concentrations assumed proportional to NO_x emissions), it is found that standard violations in Central Los Angeles, (55 in 1969), can be reduced to 25, 5, and 0 days per year by controlling emissions to 800, 550, and 300 tons /day, respectively. A probabilistic model reveals that RHC control is much more effective than NO_x control in reducing Central Los Angeles ozone. The 150 days per year ozone violations in 1969 can be reduced to 75, 30, 10, and 0 days per year by abating RHC emissions to 700, 450, 300, and 150 tons/day, respectively, (at the 1969 NO_x emission level).

The control cost-emission level and air quality-emission level relationships are combined in a graphical solution of the complete model to find the cost of various air quality levels. Best possible air quality levels with the controls considered here are 8 O₃ and 10 NO₂ violations per year (minimum ozone program) or 25 O₃ and 3 NO₂ violations per year (minimum NO₂ program) with an annualized cost of $230,000,000 (above the estimated $150,000,000 per year for the new car control program for Los Angeles County motor vehicles in 1975).

Diseño del procedimiento para la validación de los equipos de un sistema de control de acceso de RFID pasivo

[ES]En este documento se realiza el diseño de un procedimiento para la validación de los equipos necesarios a la hora de implantar un sistema de control de acceso mediante RFID pasivo. Para ello, se analizarán los distintos tipos de sistemas RFID y se elige uno para la posterior adquisición de los dispositivos necesarios. Se comprobará la normativa vigente ETSI, que regula las emisiones de potencia de los equipos de identificación por radiofrecuencia, y se verificará que se cumplen los requisitos necesarios para implantar el sistema de control de acceso realizando un análisis funcional en situaciones reales.

Diseño y despliegue de una red inalámbrica segura y control de acceso de sensores IP

[ES]El proyecto está orientado a conseguir una comunicación inalámbrica y segura de una red de sensores IP. Por un lado, mediante el protocolo 6LoWPAN se consigue que los datos se transmitan mediante IPv6 y, por otro lado, gracias al protocolo LADON se establecen los servicios de seguridad de autenticación, integridad de datos, autorización y control de acceso.

How resources control aggression in Drosophila

How animals use sensory information to weigh the risks vs. benefits of behavioral decisions remains poorly understood. Inter-male aggression is triggered when animals perceive both the presence of an appetitive resource, such as food or females, and of competing conspecific males. How such signals are detected and integrated to control the decision to fight is not clear. Here we use the vinegar fly, Drosophila melanogaster, to investigate the manner in which food and females promotes aggression.

In the first chapter, we explore how food controls aggression. As in many other species, food promotes aggression in flies, but it is not clear whether food increases aggression per se, or whether aggression is a secondary consequence of increased social interactions caused by aggregation of flies on food. Furthermore, nothing is known about how animals evaluate the quality and quantity of food in the context of competition. We show that food promotes aggression independently of any effect to increase the frequency of contact between males. Food increases aggression but not courtship between males, suggesting that the effect of food on aggression is specific. Next, we show that flies tune the level of aggression according to absolute amount of food rather than other parameters, such as area or concentration of food. Sucrose, a sugar molecule present in many fruits, is sufficient to promote aggression, and detection of sugar via gustatory receptor neurons is necessary for food-promoted aggression. Furthermore, we show that while food is necessary for aggression, too much food decreases aggression. Finally, we show that flies exhibit strategies consistent with a territorial strategy. These data suggest that flies use sweet-sensing gustatory information to guide their decision to fight over a limited quantity of a food resource.

Following up on the findings of the first chapter, we asked how the presence of a conspecific female resource promotes male-male aggression. In the absence of food, group-housed male flies, who normally do not fight even in the presence of food, fight in the presence of females. Unlike food, the presence of females strongly influences proximity between flies. Nevertheless, as group-housed flies do not fight even when they are in small chambers, it is unlikely that the presence of female indirectly increases aggression by first increasing proximity. Unlike food, the presence of females also leads to large increases in locomotion and in male-female courtship behaviors, suggesting that females may influence aggression as well as general arousal. Female cuticular hydrocarbons are required for this effect, as females that do not produce CH pheromones are unable to promote male-male aggression. In particular, 7,11-HD––a female-specific cuticular hydrocarbon pheromone critical for male-female courtship––is sufficient to mediate this effect when it is perfumed onto pheromone-deficient females or males. Recent studies showed that ppk23⁺ GRNs label two population of GRNs, one of which detects male cuticular hydrocarbons and another labeled by ppk23 and ppk25, which detects female cuticular hydrocarbons. I show that in particular, both of these GRNs control aggression, presumably via detection of female or male pheromones. To further investigate the ways in which these two classes of GRNs control aggression, I developed new genetic tools to independently test the male- and female-sensing GRNs. I show that ppk25-LexA and ppk25-GAL80 faithfully recapitulate the expression pattern of ppk25-GAL4 and label a subset of ppk23⁺ GRNs. These tools can be used in future studies to dissect the respective functions of male-sensing and female-sensing GRNs in male social behaviors.

Finally, in the last chapter, I discuss quantitative approaches to describe how varying quantities of food and females could control the level of aggression. Flies show an inverse-U shaped aggressive response to varying quantities of food and a flat aggressive response to varying quantities of females. I show how two simple game theoretic models, “prisoner’s dilemma” and “coordination game” could be used to describe the level of aggression we observe. These results suggest that flies may use strategic decision-making, using simple comparisons of costs and benefits.

In conclusion, male-male aggression in Drosophila is controlled by simple gustatory cues from food and females, which are detected by gustatory receptor neurons. Different quantities of resource cues lead to different levels of aggression, and flies show putative territorial behavior, suggesting that fly aggression is a highly strategic adaptive behavior. How these resource cues are integrated with male pheromone cues and give rise to this complex behavior is an interesting subject, which should keep researchers busy in the coming years.

Modelado y control de estación de célula de manipulación

[ES]El objetivo de este proyecto es el diseño e implementación del modelo de la estación FMS 201 (alimentación de la base) y el diseño e implementación del control de la estación. Esta estación pertenece a la serie FMS 200 (sistema didáctico modular de ensamblaje flexible) distribuido por la empresa SMC. Se dispone uno en el laboratorio de investigación del departamento de Ingeniería de Sistemas y Automática de la Escuela Superior de Ingeniería de Bilbao (EHU/UPV). Para el desarrollo e implementación del modelo se usará la herramienta informática Automation Studio. Para el control del modelo se usará el PLC. Para el intercambio de información entre modelo y controlador se utilizará la comunicación OPC Para el control de la estación se usa un PLC S7-300 de la marca SIEMENS. Se finaliza el documento realizando las pruebas de validación del modelo desarrollado, ejecutándose el programa de control en el PLC y corriendo el modelo desarrollado en el PC.

Distributed Load Control in Multiphase Radial Networks

The current power grid is on the cusp of modernization due to the emergence of distributed generation and controllable loads, as well as renewable energy. On one hand, distributed and renewable generation is volatile and difficult to dispatch. On the other hand, controllable loads provide significant potential for compensating for the uncertainties. In a future grid where there are thousands or millions of controllable loads and a large portion of the generation comes from volatile sources like wind and solar, distributed control that shifts or reduces the power consumption of electric loads in a reliable and economic way would be highly valuable.

Load control needs to be conducted with network awareness. Otherwise, voltage violations and overloading of circuit devices are likely. To model these effects, network power flows and voltages have to be considered explicitly. However, the physical laws that determine power flows and voltages are nonlinear. Furthermore, while distributed generation and controllable loads are mostly located in distribution networks that are multiphase and radial, most of the power flow studies focus on single-phase networks.

This thesis focuses on distributed load control in multiphase radial distribution networks. In particular, we first study distributed load control without considering network constraints, and then consider network-aware distributed load control.

Distributed implementation of load control is the main challenge if network constraints can be ignored. In this case, we first ignore the uncertainties in renewable generation and load arrivals, and propose a distributed load control algorithm, Algorithm 1, that optimally schedules the deferrable loads to shape the net electricity demand. Deferrable loads refer to loads whose total energy consumption is fixed, but energy usage can be shifted over time in response to network conditions. Algorithm 1 is a distributed gradient decent algorithm, and empirically converges to optimal deferrable load schedules within 15 iterations.

We then extend Algorithm 1 to a real-time setup where deferrable loads arrive over time, and only imprecise predictions about future renewable generation and load are available at the time of decision making. The real-time algorithm Algorithm 2 is based on model-predictive control: Algorithm 2 uses updated predictions on renewable generation as the true values, and computes a pseudo load to simulate future deferrable load. The pseudo load consumes 0 power at the current time step, and its total energy consumption equals the expectation of future deferrable load total energy request.

Network constraints, e.g., transformer loading constraints and voltage regulation constraints, bring significant challenge to the load control problem since power flows and voltages are governed by nonlinear physical laws. Remarkably, distribution networks are usually multiphase and radial. Two approaches are explored to overcome this challenge: one based on convex relaxation and the other that seeks a locally optimal load schedule.

To explore the convex relaxation approach, a novel but equivalent power flow model, the branch flow model, is developed, and a semidefinite programming relaxation, called BFM-SDP, is obtained using the branch flow model. BFM-SDP is mathematically equivalent to a standard convex relaxation proposed in the literature, but numerically is much more stable. Empirical studies show that BFM-SDP is numerically exact for the IEEE 13-, 34-, 37-, 123-bus networks and a real-world 2065-bus network, while the standard convex relaxation is numerically exact for only two of these networks.

Theoretical guarantees on the exactness of convex relaxations are provided for two types of networks: single-phase radial alternative-current (AC) networks, and single-phase mesh direct-current (DC) networks. In particular, for single-phase radial AC networks, we prove that a second-order cone program (SOCP) relaxation is exact if voltage upper bounds are not binding; we also modify the optimal load control problem so that its SOCP relaxation is always exact. For single-phase mesh DC networks, we prove that an SOCP relaxation is exact if 1) voltage upper bounds are not binding, or 2) voltage upper bounds are uniform and power injection lower bounds are strictly negative; we also modify the optimal load control problem so that its SOCP relaxation is always exact.

To seek a locally optimal load schedule, a distributed gradient-decent algorithm, Algorithm 9, is proposed. The suboptimality gap of the algorithm is rigorously characterized and close to 0 for practical networks. Furthermore, unlike the convex relaxation approach, Algorithm 9 ensures a feasible solution. The gradients used in Algorithm 9 are estimated based on a linear approximation of the power flow, which is derived with the following assumptions: 1) line losses are negligible; and 2) voltages are reasonably balanced. Both assumptions are satisfied in practical distribution networks. Empirical results show that Algorithm 9 obtains 70+ times speed up over the convex relaxation approach, at the cost of a suboptimality within numerical precision.

A seven year study of the life cycle of the Mayfly Ephemera danica

Ephemera danica Müller, 1764 (Ephemeroptera) is one of the largest mayflies found in the British Isles with some females reaching over 30 mm. It is a common and widespread species found in rivers, lakes and streams throughout Europe and is particularly abundant in many of the lowland rivers of the British Isles. The larvae are burrowers – mainly found where silt accumulates below macrophytes. This article gives a general overview of research work on the factors affecting the life cycle of Ephemera danica over a seven year period (1995–2002) on two rivers, the River Test at Leckford in Hampshire and the North Wey at Tilford in Surrey.

Algoritmo para la identificación de las ganancias óptimas del algoritmo de control de posición de un mecanismo de cinemática paralela

[ES]Este trabajo presenta un algoritmo automatizado cuyo resultado es la determinación de las ganancias óptimas del lazo de control de un mecanismo de cinemática paralela. En concreto se ha aplicado al mecanismo 5R, aunque el método es válido para cualquier otro mecanismo introduciendo el modelo mecatrónico correspondiente. Permite disponer de un procedimiento para poder elegir en un futuro la combinación de motor y reductora más apropiada para un determinado mecanismo evitando realizar adquisiciones sobredimensionadas, como ocurrió con el mecanismo en cuestión.

Hydrobiological service for observations and control of surface waters in the USSR

Technological progress, having reached in our time an unprecedented speed, is still increasing the rate of mineral extraction, industrial construction, and the mastering of new kinds of energy is growing. Correspondingly the anthropogenic load on the biosphere is increased and that requires the comprehensive development of monitoring the anthropogenic changes in the natural environment. Among problems resulting from the scientific-technological development, a noticeable place is given to the problem of pure water. Surface land waters proved to be a sensitive link in the natural environment. The hydrobiological service for observations and control of the surface waters is one of the subsystems of the State/Federal Service for Observations and Control of pollution levels in environmental objects, conducted by the USSR State Committee for Hydrometeor- ology and Control of the Natural Environment. This paper summarises the the main principles of the organisation and goals of the national system of monitoring of the state of the natural environment in the USSR.

A nonlinear systems model for the control mechanism of free fatty acid-glucose metabolosm in normal humans

A mathematical model is proposed in this thesis for the control mechanism of free fatty acid-glucose metabolism in healthy individuals under resting conditions. The objective is to explain in a consistent manner some clinical laboratory observations such as glucose, insulin and free fatty acid responses to intravenous injection of glucose, insulin, etc. Responses up to only about two hours from the beginning of infusion are considered. The model is an extension of the one for glucose homeostasis proposed by Charette, Kadish and Sridhar (Modeling and Control Aspects of Glucose Homeostasis. Mathematical Biosciences, 1969). It is based upon a systems approach and agrees with the current theories of glucose and free fatty acid metabolism. The description is in terms of ordinary differential equations. Validation of the model is based on clinical laboratory data available at the present time. Finally procedures are suggested for systematically identifying the parameters associated with the free fatty acid portion of the model.

Design and control of an ultraprecision stage used in grating tiling

In petawatt laser system, the gratings used to compose pulse compressor are very large in size which can be only acquired currently by arraying small aperture gratings to form a large one instead, an approach referred to as grating tiling. Theory and experiments have demonstrated that the coherent addition of multiple small gratings to form a larger grating is viable, the key technology of which is to control the relative position and orientation of each grating with high precision. According to the main factors that affect the performance of the grating tiling, a 5-DOF ultraprecision stage is developed for the grating tiling experiment. The mechanism is formed by serial structures. The motion of the mechanism is guided by flexure hinges and driven by piezoelectric actuators and the movement resolution of which can achieve nanometer level. To keep the stability of the mechanism, capacitive position sensors with nanometer accuracy are fixed on it to provide feedback signals with which to realize closed-loop control, thus the positioning precision of the mechanism is within several nanometers range through voltage control and digital PID algorithm. Results of experiments indicate that the performance of the mechanism can meet the requirement of precision for grating tiling.}

Efeitos do uso de antiinflamatório e do exercício aeróbico sobre a regeneração tecidual e perfil biomecânico do tendão calcâneo de ratos após ruptura completa

Ruptura do tendão calcâneo é uma das lesões tendíneas mais frequentes. Embora a maioria dos trabalhos sugira que o exercício seja benéfico na cicatrização tendínea, não há consenso sobre o efeito do antiinflamatório neste contexto. Trabalhos experimentais tentam reproduzir lesão aguda deste tendão, em diferentes espécies animais. Neste estudo, descrevemos uma técnica de tenotomia completa do tendão calcâneo direito em ratos e, em seguida, avaliamos os efeitos do uso do antiinflamatório e do exercício aeróbico, isoladamente e em combinação, sobre a proliferação celular e o perfil biomecânico do tendão calcâneo, durante o processo de cicatrização após tenotomia. Estudo experimental com 156 ratos machos adultos, da raça Wistar, com idade média de 3 meses e peso médio de 300g. Após anestesia com tiopental e com auxílio da microscopia de luz, foi realizada incisão longitudinal posterior de cinco milímetros, em direção proximal, a partir da tuberosidade posterior do calcâneo da pata direita do rato. Foi feito corte transversal do tendão calcâneo, a sete milímetros da tuberosidade do calcâneo, com preservação do tendão plantar. Utilizamos as técnicas de Hematoxilina e Eosina, Picrosirius-red e Resorcina-fucsina de Weigert para avaliação da cicatrização tendínea e das fibras dos sistemas colágeno e elástico. Após a tenotomia, metade dos animais receberam tenoxicam intramuscular por 7 dias e no 8o dia iniciou-se protocolo de exercício em esteira na metade de cada grupo. Os ratos foram divididos aleatoriamente em 4 grupos de tratamento: A sem antiinflamatório E sem exercício (controle); B com antiinflamatório E com exercício; C sem antiinflamatório E com exercício; D com antiinflamatório E sem exercício. Os animais foram eutanasiados com 1, 2, 4 e 8 semanas após a tenotomia, para avaliação histológica pelo PCNA, e biomecânica através do teste de resistência à tração e da medida do ciclo locomotor. Foram realizados análise de variância, teste de Kruskal-Wallis e o método de Bonferroni, no programa R Project, versão 2.11.1. O tempo cirúrgico médio foi de 1 minuto e 24 segundos, sem complicações observadas até a 8a semana pós-operatória. Observamos proliferação celular e fibrilogênese com duas semanas, e diminuição da celularidade e das fibras elásticas na 8a semana, além de mudanças na organização estrutural do sistema colágeno. Encontramos pico da imunomarcação com PCNA na 2a semana em todos os grupos, exceto no grupo A, cujo pico aconteceu com 1 semana da tenotomia. Evidenciamos resistência à tração significativamente maior (p=0,02) nos ratos submetidos ao exercício, 8 semanas após ruptura. Nos grupos com antiinflamatório, observamos um ciclo locomotor mais estável durante todo o tempo avaliado. Consideramos a técnica cirúrgica experimental de tenotomia completa do tendão calcâneo, realizada com auxílio da microscopia de luz e preservação do tendão plantar, simples, rápida, com sinais de cicatrização tendínea normal e de fácil reprodução em ratos. O exercício aeróbico, iniciado precocemente após tenotomia completa do tendão calcâneo, é significativamente benéfico na sua recuperação biomecânica e o uso combinado com antiinflamatório confere maior estabilidade na marcha, o que pode proteger contra rerruptura tendínea em ratos

A Real-Time Sliding Mode Control for a Wind Energy System Based on a Doubly Fed Induction Generator

In this paper, a real time sliding mode control scheme for a variable speed wind turbine that incorporates a doubly feed induction generator is described. In this design, the so-called vector control theory is applied, in order to simplify the system electrical equations. The proposed control scheme involves a low computational cost and therefore can be implemented in real-time applications using a low cost Digital Signal Processor (DSP). The stability analysis of the proposed sliding mode controller under disturbances and parameter uncertainties is provided using the Lyapunov stability theory. A new experimental platform has been designed and constructed in order to analyze the real-time performance of the proposed controller in a real system. Finally, the experimental validation carried out in the experimental platform shows; on the one hand that the proposed controller provides high-performance dynamic characteristics, and on the other hand that this scheme is robust with respect to the uncertainties that usually appear in the real systems.

A Data Dropout Compensation Algorithm Based on the Iterative Learning Control Methodology for Discrete-Time Systems

This paper deals with the convergence of a remote iterative learning control system subject to data dropouts. The system is composed by a set of discrete-time multiple input-multiple output linear models, each one with its corresponding actuator device and its sensor. Each actuator applies the input signals vector to its corresponding model at the sampling instants and the sensor measures the output signals vector. The iterative learning law is processed in a controller located far away of the models so the control signals vector has to be transmitted from the controller to the actuators through transmission channels. Such a law uses the measurements of each model to generate the input vector to be applied to its subsequent model so the measurements of the models have to be transmitted from the sensors to the controller. All transmissions are subject to failures which are described as a binary sequence taking value 1 or 0. A compensation dropout technique is used to replace the lost data in the transmission processes. The convergence to zero of the errors between the output signals vector and a reference one is achieved as the number of models tends to infinity.