Performance improvement of asymmetrical filtered 40GB/s RZ-DPSK receiver design-strong filtering considerations

We present a novel differential phase shift keying receiver design under strong optical filtering. The receiver design is based on asymmetrical filtering at the destructive port of the Mach Zehnder Interferometer. The asymmetrical filtered receiver design can significantly increase performance by 2 to 4.7dB in calculated "Q".

Optical in-fiber Bragg grating sensor systems for medical applications

Two in-fiber Bragg grating (FBG) temperature sensor systems for medical applications are demonstrated: (1) an FBG flow-directed thermodilution catheter based on interferometric detection of wavelength shift that is used for cardiac monitoring; and (2) an FBG sensor system with a tunable Fabry-Perot filter for in vivo temperature profiling in nuclear magnetic resonance (NMR) machines. Preliminary results show that the FBG sensor is in good agreement with electrical sensors that are widely used in practice. A field test shows that the FBG sensor system is suitable for in situ temperature profiling in NMR machines for medical applications.

Pilot tone design for dispersion estimation in coherent optical fast OFDM systems

We show that inserting pilot tones with frequency intervals inversely proportional to the subcarrier index exhibits greatly improved dispersion estimation performance when compared to the equal spacing design in optical fast orthogonal frequency division multiplexing (F-OFDM). With the proposed design, a 20-Gbit/s four amplitude shift keying optical F-OFDM system with 840-km transmission without optical dispersion compensation is experimentally demonstrated. It is shown that a single F-OFDM symbol with six pilot tones can achieve near-optimal estimation performance for the 840-km dispersion. This is in contrast to the minimum of ten pilot tones using an equal spacing design with either cubic or Fourier-transform-based interpolation. © 2013 Elsevier B.V. All rights reserved.

Optical sensor interrogation with a blazed fiber Bragg grating and a charge-coupled device linear array

We present what is to our knowledge the first comprehensive investigation of the use of blazed fiber Bragg gratings (BFBGs) to interrogate wavelength division multiplexed (WDM) in-fiber optical sensor arrays. We show that the light outcoupled from the core of these BFBGs is radiated with sufficient optical power that it may be detected with a low-cost charge-coupled device (CCD) array. We present thorough system performance analysis that shows sufficient spectral-spatial resolution to decode sensors with a WDM separation of 75 ρm, signal-to-noise ratio greater than 45-dB bandwidth of 70 nm, and drift of only 0.1 ρm. We show the system to be polarization-state insensitive, making the BFBG-CCD spectral analysis technique a practical, extremely low-cost, alternative to traditional tunable filter approaches.

Water detection in jet fuel using a polymer optical fibre Bragg grating

Water is a common impurity of jet fuel, and can exist in three forms: dissolved in the fuel, as a suspension and as a distinct layer at the bottom of the fuel tank. Water cannot practically be eliminated from fuel but must be kept to a minimum as large quantities can cause engine problems, particularly when frozen, and the interface between water and fuel acts as a breeding ground for biological contaminants. The quantities of dissolved or suspended water are quite small, ranging from about 10 ppm to 150 ppm. This makes the measurement task difficult and there is currently a lack of a convenient, electrically passive system for water-in-fuel monitoring; instead the airlines rely on colorimetric spot tests or simply draining liquid from the bottom of fuel tanks. For all these reason, people have explored different ways to detect water in fuel, however all these approaches have problems, e.g. they may not be electrically passive or they may be sensitive to the refractive index of the fuel. In this paper, we present a simple, direct and sensitive approach involving the use of a polymer optical fibre Bragg grating to detect water in fuel. The principle is that poly(methyl methacrylate) (PMMA) can absorb moisture from its surroundings (up to 2% at 23 °C), leading to both a swelling of the material and an increase in refractive index with a consequent increase in the Bragg wavelength of a grating inscribed in the material.

Bit-error probability for direct detection of optical RZ signal degraded by ASE noise and timing jitter

We analyze theoretically the interplay between optical return-to-zero signal degradation due to timing jitter and additive amplified-spontaneous-emission noise. The impact of these two factors on the performance of a square-law direct detection receiver is also investigated. We derive an analytical expression for the bit-error probability and quantitatively determine the conditions when the contributions of the effects of timing jitter and additive noise to the bit error rate can be treated separately. The analysis of patterning effects is also presented. © 2007 IEEE.

Non-invasive respiratory monitoring using long-period fiber grating sensors

In non-invasive ventilation, continuous monitoring of respiratory volumes is essential. Here, we present a method for the measurement of respiratory volumes by a single fiber-grating sensor of bending and provide the proof-of-principle by applying a calibration-test measurement procedure on a set of 18 healthy volunteers. Results establish a linear correlation between a change in lung volume and the corresponding change in a local thorax curvature. They also show good sensor accuracy in measurements of tidal and minute respiratory volumes for different types of breathing. The proposed technique does not rely on the air flow through an oronasal mask or the observation of chest movement by a clinician, which distinguishes it from the current clinical practice. © 2014 Optical Society of America.

A new method for respiratory-volume monitoring based on long-period fibre gratings

Respiratory-volume monitoring is an indispensable part of mechanical ventilation. Here we present a new method of the respiratory-volume measurement based on a single fibre-optical long-period sensor of bending and the correlation between torso curvature and lung volume. Unlike the commonly used air-flow based measurement methods the proposed sensor is drift-free and immune to air-leaks. In the paper, we explain the working principle of sensors, a two-step calibration-test measurement procedure and present results that establish a linear correlation between the change in the local thorax curvature and the change of the lung volume. We also discuss the advantages and limitations of these sensors with respect to the current standards. © 2013 IEEE.

Effects of crosstalk in WDM optical label switching networks due to wavelength switching of a tunable laser

Crosstalk caused by switching events in fast tunable lasers in an optical label switching (OLS) system is investigated for the first time. A wavelength-division-multiplexed OLS system based on subcarrier multiplexed labels is presented which employs a 40-Gb/s duobinary payload and a 155-Mb/s label on a 40-GHz subcarrier. Degradation in system performance as the transmitters switch between different channels is then characterized in terms of the frequency drift of the tunable laser.

Monitoring long distance WDM communication lines using a high-loss loopback supervisory system

In this paper, we present experimental results for monitoring long distance WDM communication links using a line monitoring system suitable for legacy optically amplified long-haul undersea systems. This monitoring system is based on setting up a simple, passive, low cost high-loss optical loopback circuit at each repeater that provides a connection between the existing anti-directional undersea fibres, and can be used to define fault location. Fault location is achieved by transmitting a short pulse supervisory signal along with the WDM data signals where a portion of the overall signal is attenuated and returned to the transmit terminal by the loopback circuit. A special receiver is used at the terminal to extract the weakly returned supervisory signal where each supervisory signal is received at different times corresponding to different optical repeaters. Therefore, the degradation in any repeater appears on its corresponding supervisory signal level. We use a recirculating loop to simulate a 4600 km fibre link, on which a high-loss loopback supervisory system is implemented. Successful monitoring is accomplished through the production of an appropriate supervisory signal at the terminal that is detected and identified in a satisfactory time period after passing through up to 45 dB attenuation in the loopback circuit. © 2012 Elsevier B.V. All rights reserved.

Monitoring long distance WDM communication lines using a high-loss loopback supervisory system

In this paper, we present experimental results for monitoring long distance WDM communication links using a line monitoring system suitable for legacy optically amplified long-haul undersea systems. This monitoring system is based on setting up a simple, passive, low cost high-loss optical loopback circuit at each repeater that provides a connection between the existing anti-directional undersea fibres, and can be used to define fault location. Fault location is achieved by transmitting a short pulse supervisory signal along with the WDM data signals where a portion of the overall signal is attenuated and returned to the transmit terminal by the loopback circuit. A special receiver is used at the terminal to extract the weakly returned supervisory signal where each supervisory signal is received at different times corresponding to different optical repeaters. Therefore, the degradation in any repeater appears on its corresponding supervisory signal level. We use a recirculating loop to simulate a 4600 km fibre link, on which a high-loss loopback supervisory system is implemented. Successful monitoring is accomplished through the production of an appropriate supervisory signal at the terminal that is detected and identified in a satisfactory time period after passing through up to 45 dB attenuation in the loopback circuit. © 2012 Elsevier B.V. All rights reserved.

Advanced techniques for the improvement of optical transmission systems

This thesis presents the experimental investigation into two novel techniques which can be incorporated into current optical systems. These techniques have the capability to improve the performance of transmission and the recovery of the transmitted signal at the receiver. The experimental objectives are described and the results for each technique are presented in two sections: The first experimental section is on work related to Ultra-long Raman Fibre lasers (ULRFLs). The fibre lasers have become an important research topic in recent years due to the significant improvement they give over lumped Raman amplification and their potential use in the development of system with large bandwidths and very low losses. The experiments involved the use of ASK and DPSK modulation types over a distance of 240km and DPSK over a distance of 320km. These results are compared to the current state of-the-art and against other types of ultra-long transmission amplification techniques. The second technique investigated involves asymmetrical, or offset, filtering. This technique is important because it deals with the strong filtering regimes that are a part of optical systems and networks in modern high-speed communications. It allows the improvement of the received signal by offsetting the central frequency of a filter after the output of a Delay Line Interferometer (DLI), which induces significant improvement in BER and/or Qvalues at the receiver and therefore an increase in signal quality. The experimental results are then concluded against the objectives of the experimental work and potential future work discussed.

Optical 2R regeneration at 40 Gbit/s using saturable absorber in long-haul dispersion-managed fiber links

The optical regeneration is an attractive method to improve the performance of long-distance data transmission, though its application in high-speed fiber systems requires careful design consideration/optimization. In this letter we investigate 40 Gbit/s dispersion-managed fiber transmission with optical 2R regeneration based on quantum well saturable absorber and highly non-linear fiber. We demonstrate through numerical modeling a feasibility of a single channel transmission over 10,000 km using optimized system design. © 2003 Elsevier B.V. All rights reserved.

Dual-polarization multi-band optical OFDM transmission and transceiver limitations for up to 500 Gb/s uncompensated long-haul links

A number of critical issues for dual-polarization single- and multi-band optical orthogonal-frequency division multiplexing (DPSB/ MB-OFDM) signals are analyzed in dispersion compensation fiber (DCF)-free long-haul links. For the first time, different DP crosstalk removal techniques are compared, the maximum transmission-reach is investigated, and the impact of subcarrier number and high-level modulation formats are explored thoroughly. It is shown, for a bit-error-rate (BER) of 10-3, 2000 km of quaternary phase-shift keying (QPSK) DP-MBOFDM transmission is feasible. At high launched optical powers (LOP), maximum-likelihood decoding can extend the LOP of 40 Gb/s QPSK DPSB- OFDM at 2000 km by 1.5 dB compared to zero-forcing. For a 100 Gb/s DP-MB-OFDM system, a high number of subcarriers contribute to improved BER but at the cost of digital signal processing computational complexity, whilst by adapting the cyclic prefix length the BER can be improved for a low number of subcarriers. In addition, when 16-quadrature amplitude modulation (16QAM) is employed the digital-toanalogue/ analogue-to-digital converter (DAC/ADC) bandwidth is relaxed with a degraded BER; while the 'circular' 8QAM is slightly superior to its 'rectangular' form. Finally, the transmission of wavelength-division multiplexing DP-MB-OFDM and single-carrier DP-QPSK is experimentally compared for up to 500 Gb/s showing great potential and similar performance at 1000 km DCF-free G.652 line. © 2014 Optical Society of America.

High stress monitoring of prestressing tendons in nuclear concrete vessels using fibre-optic sensors

Maintaining the structural health of prestressed concrete nuclear containments is a key element in ensuring nuclear reactors are capable of meeting their safety requirements. This paper discusses the attachment, fabrication and characterisation of optical fibre strain sensors suitable for the prestress monitoring of irradiated steel prestressing tendons. The all-metal fabrication and welding process allowed the instrumented strand to simultaneously monitor and apply stresses up to 1300 MPa (80% of steel's ultimate tensile strength). There were no adverse effects to the strand's mechanical properties or integrity. After sensor relaxation through cyclic stress treatment, strain transfer between the optical fibre sensors and the strand remained at 69%. The fibre strain sensors could also withstand the non-axial forces induced as the strand was deflected around a 4.5 m bend radius. Further development of this technology has the potential to augment current prestress monitoring practices, allowing distributed measurements of short- and long-term prestress losses in nuclear prestressed-concrete vessels. © 2014 Elsevier B.V.