Ship-board measurements and estimations of air-sea fluxes in the western tropical Pacific during TOGA COARE

Direct air-sea flux measurements were made on RN Kexue #1 at 40 degrees S, 156 degrees E during the Tropical Ocean Global Atmosphere (TOGA) Coupled Ocean-Atmospheric Response Experiment (COARE) Intensive Observation Period (IOP). An array of six accelerometers was used to measure the motion of the anchored ship, and a sonic anemometer and Lyman-alpha hygrometer were used to measure the turbulent wind vector and specific humidity. The contamination of the turbulent wind components by ship motion was largely removed by an improvement of a procedure due to Shao based on the acceleration signals. The scheme of the wind correction for ship motion is briefly outlined. Results are presented from data for the best wind direction relative to the ship to minimize flow distortion effects. Both the time series and the power spectra of the sonic-measured wind components show swell-induced ship motion contamination, which is largely removed by the accelerometer correction scheme, There was less contamination in the longitudinal wind component than in the vertical and transverse components. The spectral characteristics of the surface-layer turbulence properties are compared with those from previous land and ocean results, Momentum and latent heat fluxes were calculated by eddy correlation and compared to those estimated by the inertial dissipation method and the TOGA COARE bulk formula. The estimations of wind stress determined by eddy correlation are smaller than those from the TOGA COARE bulk formula, especially for higher wind speeds, while those from the bulk formula and inertial dissipation technique are generally in agreement. The estimations of latent heal flux from the three different methods are in reasonable agreement. The effect of the correction for ship motion on latent heat fluxes is not as large as on momentum fluxes.

AFLP-based genetic linkage maps of the Pacific oyster Crassostrea gigas Thunberg

Amplified fragment length polymorphisms (AFLPs) were used for genome mapping in the Pacific Oyster Crassostrea gigas Thunberg. Seventeen selected primer combinations produced 1106 peaks, of which 384 (34.7%) were polymorphic in a backcross family. Among the polymorphic markers, 349 were segregating through either the female or the male parent. Chi-square analysis indicated that 255 (73.1%) of the markers segregated in a Mendelian ratio, and 94 (26.9%) showed significant (P < 0.05) segregation distortion. Separate genetic linkage maps were constructed for the female and male parents. The female framework map consisted of 119 markers in 11 linkage groups, spanning 1030.7 cM, with an average interval of 9.5 cM per marker. The male map contained 96 markers in 10 linkage groups, covering 758.4 cM, with 8.8 cM per marker. The estimated genome length of the Pacific oyster was 1258 cM for the female and 933 cM for the male, and the observed coverage was 82.0% for the female map and 81.3% for the male map. Most distorted markers were deficient for homozygotes and closely linked to each other on the genetic map, suggesting the presence of major recessive deleterious genes in the Pacific oyster.

用于移动机器人自定位的视觉路标设计

为了实现室内移动机器人的自定位,提出了一种简易美观的新型视觉人工路标以及基于对数极坐标系投影直方图的路标识别方法,并用基于共面四点的位姿估计算法计算机器人位姿。实验结果说明,路标检测具有很高的鲁棒性;路标识别方法抗噪声和形变的能力强;位姿精度足够满足室内移动机器人自定位的需要。

用波动方程建立蠕动爬行攻泥机器人海底土力学运动模型

针对目前国内海底蠕动爬行机器人攻打千斤洞的特点 ,在对海洋沉积土的工程性质进行分析的基础上 ,利用流变力学的理论 ,提出用波动方程来建立攻泥机器人周期性冲击土壤的力学模型 ,用后向差分法解波动方程 ,得到土壤的位移和变形公式 ,确定土壤对攻泥机的阻力 .通过对模型的仿真 ,证明了用该模型计算阻力的可行性 .

JPEG压缩编码的扩充自适应量化器设计

在ＪＰＥＧ静止图象压缩的基础上，设计了一种扩充的自适应量化器．利用人眼的视觉特征，通过分析ＭＣＵ块的局部视觉活动性，以ＭＣＵ活动性函数确定量化因子，并引入亮度掩盖算子调节量化参量．实验结果表明，本文所设计的自适应量化器能减少图象编码主观失真，改善图象质量，获得更好的压缩效果

实时自适应量化法——逐级均值法

本文以跟踪电视系统中自适应量化器为设计背景,提出了一种新的、实时自适应的快速图象量化方法——逐极均值法,文中首先用Lloyd-Max最佳量化理论分析了这种量化方法的均方误差失真,讨沦了图象中存在孤立亮点时的处理方法。然后论述了这种量化方法应用于跟踪电视系统中的性能,即实现的简单、快速性;对照度变化的自适应性;及图象对比度增强效果。文中通过图象处理实验结果验证了这种量化方法的性能和理论分析的正确性。最后得出结论:逐极均值法量化器是一种能够代替LlodyMax最佳量化器的次佳量化器,这种量化器可以很好地满足跟踪电视系统中对自适应量化器的设计所提出的各方面性能要求;它对那些要求实现简单、实时自适应的量化器应用领域也将具有一定意义。

不同基板预热温度对激光金属沉积成形过程温度场的影响

为降低成形过程的热应力,抑制成形过程裂缝的产生,减小成形过程试样和基板的翘曲变形,激光金属沉积成形往往需要进行基板预热,因此研究不同基板预热温度对激光金属沉积成形过程温度场的影响具有非常重要的意义.根据有限元分析中的"单元生死"技术,利用APDL编程建立了基板预热对激光金属沉积成形过程温度场影响的三维多道多层数值模拟模型,详细分析了基板未预热和分别预热到200,300,400,500,600℃时对沉积成形过程温度场和温度梯度的影响.通过中国科学院沈阳自动化研究所自行研制的激光金属沉积成形系统和基板预热系统,在与模拟过程相同的参数下,利用镍基合金粉末在基板未预热和分别预热到300,400,500,560℃时进行了成形试验,试验结果跟数值模拟结果吻合较好.

不同基板预热温度对激光金属沉积成形过程热应力影响的研究

研究不同基板预热温度对激光金属沉积成形过程热应力的影响,对于降低成形过程的热应力,抑制成形过程裂缝的产生,减小成形过程试样和基板的翘曲变形具有非常重要的意义。根据有限元分析中的"单元生死"技术,编程建立了基板预热对激光金属沉积成形过程热应力影响的三维多道多层数值模拟模型,详细分析了基板未预热和分别预热到200℃、300℃、400℃、500℃、600℃时对沉积成形过程VonMise’s热应力、X方向、Y方向以及Z方向热应力的影响。在与模拟过程相同的参数下,利用镍基合金粉末分别在基板未预热和分别预热到300℃、400℃、500℃、600℃时进行了成形试验,试验的结果跟数值模拟结果吻合较好。

结构光视觉传感器误差分析与结构分析

结构光视觉传感器是视觉焊缝跟踪系统获得焊缝信息的重要组成部分,其测量误差与性能对焊缝跟踪系统的总体测量精度及可靠性有着直接影响。本文对应用于焊缝跟踪的结构光视觉传感器进行误差分析,包括传感器硬件系统结构误差、激光散斑噪声误差及镜头畸变误差等,并对不同结构方式下的视觉传感器建立了数学模型,具体分析了结构参数对其误差的影响,提出结构光视觉焊缝跟踪传感器优化设计方法,并依据仿真结果给出结构优化设计参数,最后通过实验验证了该优化设计方法的正确性。

裂缝储层预测技术应用研究

In practice,many fracture reservoir was found,which has giant potential for exporation. For example,in limestone fracture reservoir,igneous rock fracture reservoir and shale fracture reservoir ,there are high yield oil wells found. The fracture reservoir has strong anisotropy and is very difficult to explore and produce.Since 1990’s,the techniques that use structure information and P-WAVE seismic attributes to detect fracture developed very rapidly,include stress and strain analysis,using amplitude,interval velocity,time-difference,azimuthal AVO analysis etc. Based on research and develop these advanced techniques of fracture detect,this paper selected two typical fracture reservoir as target area,according to the characters of research area,selected different techniques to pridect the fracture azimuth and density of target,and at last ,confirmed the favored area. This paper includes six parts:the first chapter mainly addresses the domestic and international research actuality about the fracture prediction and the evolement in ShengLi oil field,then according to the temporal exploration requirement,a research route was established; Based on the close relationship between structural fracture and the geotectonic movement and the procedure of rock distortion，the second chapter research the structural fracture predicting technique which is realized by computing the strain in every geotectonic movement ,which is by use of the forward and inversion of the growing history of structure; The third chapter discussed many kind of traditional techniques for fracture reservoir prediction,and point out their disadvantages.then research and develop the coherence volume computing technique which can distinguish from faults,the seismic wave absorbing technique,and other fracture predicting technique which is by use of seismic attributes ,such as azimuthal AVO FVO etc; The fourth chapter first establish the geological and petrophysical model by use of the existed log and drill well information, then research the variation of amplitude and seismic wave which is caused by fractures.based on it , the fracture predicting technique which is by use of variation of azimuthal impedance is researched;The fifth chapter is a case study,it selects shale fracture reservoir in LuoJia area as target,selects several kind of techniques to apply ,at last ,the fracture distribution of target reservoir and favored area were gotten;the sixth chapter is another case study,it selects limestone fracture reservoir in BoShen6 buried hill as target,selects several kind of techniques to apply,similarly favored area were gotten. Based on deeply research and development of the new techniques for fracture reservoir exploration, This paper selects two fracture reservoirs the most typical in ShengLi as targets to be applied ,good results show up a good application way ,which can be used for reference for future fracture exploration,and it can bring materially economic and social benefit.

膨胀土化学改性实验研究

Expansive soil is a kind of typical unsaturated soil with characteristics of high swelling-shrinking deformation, cracks and over consolidation. It is very harmful to civil engineering, As a new processing method deal with expansive soil, Chemistry treatment has widespread applied in developed countries such as Europe and America, and also gained remarkable result. Based on the embankment filling soil improving testing projects in Meng-Xin freeway, this paper proposed a new processing method to expansive soil embankment wrapped with PAS-treated soil, experimental study of expansive soil chemical improved by PAS is been carried out. The water content change is the external factor which causes expansive soil to have swelling-shrinkage deformation. this reflected that the soil body swelling-shrinkage characteristic mainly depends on its mineral ingredient and the soil-water mutual function. This paper takes expansive soil as one kind of ordinary high plastic clay from angle of clay-water mutual function explained the expansive soil swelling-shrinkage deformation mechanism on microscopic. And take this swelling-shrinkage mechanism as the master line, Cooperates with the China Academy of Chemistry, we developed the new method PAS treatment, trough ionic exchange, joint, package and flocculation, the stronger static electricity function weakened the level through adsorption and the stronger static electricity function, PAS can weakened the negative charge repulsion between levels, causes the electric potential to reduce, diffusion layer thickness to be thinner, and improves the water affinity performance of expansive soil effectively. Moreover the space network architecture compromised with PAS and soil enhanced the joint strength between the clay particles , enable the soil body to have comparatively high strength and the distortion rate. pointed proposed the PAS modified principle. Combine with the construction of experimented road, this paper sums up and presents the construction craft and technology requirement of PAS treatment to expansive soil embankment. Through many experimental studied the basic physical property, the intensity characteristic and water stability changes of expansive soil and PAS-treated soil. The results of study indicate that adding lime into the expansive soil can reduce the content of clay gain obviously, reduce the plasticity notably, increase the strength greatly, control the property of swelling and shrinking effectively, and can meliorate the stability of sucking water clearly. Simultaneity PAS don’t change the cultivate capacity of the soil, the modified slope of the embankment can adopt plant fixed slope method as ecology protection. Finally the processing effect of use different treatment has analyzed through numerical simulation, summarized the PAS chemical wrapping treatment process in the actual project application, and appraised its processing effect and the project efficiency. The research indicated that PAS chemical treatment is one effective method to improve expansive soil. Compare with long-distance replacement, especially in the high plastic expansive soil massive distribution area, PAS treatment has the very greatly economical superiority to be promoted. The study in the paper not only afforded technique method to Meng-Xin expressway construction but also important for improvement of the expressway construction theory in swelling soil areas. Key words: PAS; expansive soil; swelling-shrinkage deformation mechanism; wrapping embankment; chemical modified treatment.

青藏高原东部电性结构特征及其构造意义

Eastern Himalayan Syntaxis (EHS) and its surroundings (eastern margin of Tibet) is one of the most complicated tectonic areas in the world. As the exhaust opening of the balanced materials of the Tibetan Plateau during the collision of Indan and Eurasian plates, the deep structure beneath EHS surrounding region is referred to as the key to the study of the dynamics of the plateau. EHS3D project, sponsored by NSFC, has been proposed to explore the deep electric features of the area. During the first stage of EHS3D(2006-2008), MT+LMT measurements have been conducted along two lines from Chayu to Qingshuihe (EHS3D-3) and Chayu to Ruoergai (EHS3D-2). This paper will discuss the MT models of EHS3D-3 line. By the data procrssing, including distortion analysis, Robust estimation and strike decomposition, rotated apparent resitivities and phases have been obtained for each station. Then conventional 2-D inversion algorithms (NLCG and RRI) were employed to produce 2-D models. The final preferred 2-D model suggests that the upper crust consists of resistive blocks while in mid-lower crust there are two extensive conductive bodies beneath Lhasa block and Qiangtang terrain respectively. Jinshajiang suture is a gradient belt and Bangong-Nujiang suture appear a conductive belt dipping to the north. . We concluded that the formation of the two conductive bodies attributed to the partial melt and fluids in the lower crust. The regional electric strike derived from decomposition analysis indicates that the crust and upper mantle move in different manners. The upper crust moves like slips of rigid blocks along major slip faults while the lower crust creeps as a flow in the conductive channels.

塔里木盆地塔北、塔中地区早古生代白云岩形成机理

In Tarim Basin, extensive carbonates of Lower Paleozoic occur, in which thick Cambrian and Lower Ordovician dolostones are widespread and show a potential perspective in hydrocarbon exploration. So they are viewed as an important target for exploration. Tarim Basin is a poly phase composite basin, which underwent multiphase tectonic modification and volcanic activities; these exerted significant influences on the basin-fills and basin fluid evolution, thereby the diagenetic history, particularly on the deep-buried Lower Paleozoic dolostones. Referring to the classification of dolomite texture proposed by Gregg & Sibley (1984) and Sibley & Gregg (1987). In view of crystal size, crystal shape, crystal surface and contact relation, eight genetic textures of dolomite crystals are identified, based on careful petrographic examinatoins. These textures include: 1) micritic dolomite; 2) relict mimetic dolomite; 3)finely crystalline, planar-e(s), floating dolomite; 4)finely crystalline, planar-e(s) dolomite; 5) finely-coarse crystalline, nonplanar-a dolomite; 6)coarse crystalline, nonplanar saddle dolomite; 7) finely-medium crystalline, planar-e(s) dolomite cement; 8) coarse crystalline, nonplanar saddle dolomite cement, in which the former six textures occurs as in matrix, the latter two in the cements. Detailed geochemistry analysis is carried out on the basis of genetic textures of dolomite and related minerals such as quartz and calcite. The result showed that the calcite has the highest average content in Sr, which can be sorted into two groups; micritic dolomite has the highest average content in Sr among all kinds of dolomites; the REE patterns of all kinds of dolomites is similar to those of marine limestone samples. Saddle dolomite cement has δ13C values from -2.44‰ to 1.27‰ PDB, and δ18O values from -13.01‰ to -5.12‰ PDB, which partially overlap with those of matrix dolomite (δ13C values from -2.83‰ to 2.01‰ PDB, δ18O values from -10.63‰ to -0.85‰ PDB). Saddle dolomite cement has 87Sr/86Sr ratios from 0.7086 to 0.7104, which totally overlap with those of matrix dolomite (0.7084 ~ 0.7116). Compared with saddle dolomite derived from other basins all over the world, the saddle dolomites of Tarim Basin have similar δ13C, δ18O and 87Sr/86Sr ratios values with those of matrix dolomite. This scenario reflects the unusual geological setting and special dolomitizing liquid of Tarim Basin. The values of δ18O, δ13C and 87Sr/86Sr ratios of calcite also can be sorted out two groups, which may been resulted from the one stage of extensive uplift of Tarim Basin from Mesozoic to Cenozoic. Fluid inclusion microthermometry data of the diagenetic mineral indicates that matrix dolomite has relatively low homogenization temperatures (Th) of 80～105oC and salinities of 12.3％ (wt% NaCl equivalent); saddle dolomite has highest Th values, which concentrate in 120～160oC and salinities of 13.5～23.7％ (wt% NaCl equivalent); quartz has relatively low Th of 135～155oC and salinities of 17.8～22.5％ (wt% NaCl equivalent); calcite has relatively low Th of 121～159.5oC and salinities of 1.4～17.5％ (wt% NaCl equivalent). These data suggest that the saddle dolomites could have formed in thermal brine fluids. Based on comprehensive petrographical study, detailed geochemistry and fluid inclusion microthermometry analysis on Lower Paleozoic dolomite of Tarim Basin, three types of dolomitisation mechanism are proposed: Penecontemporaneous dolomitisation (Sabkha dolomitisation & Reflux dolomitisation); Burial dolomitisation (shallow-intermediate burial dolomitisation & Deep burial dolomitisation ); Hydrothermal cannibalized dolomitisation. In view of host-specified occurrences of hydrothermal dolomite, the low abundance of saddle dolomite and high geochemical similarities between saddle dolomite and host dolomite, as well as highest Th and high salinities , the hydrothermal dolomite in Tarim Basin is thus unique, which could have been precipitated in modified fluid in the host dolomite through intraformational thermal fluid cannibalization of Mg ions from the host. This scenario is different from the cases that large scale dolomitizing fluid migration took place along the fluid pathways where abundant saddle dolomite precipitated. Detailed observations on 180 petrographic and 60 casting thin sections show original pores in Lower Paleozoic dolomite were almost died out by complicated diagenetic process after a long time geologic evolution. On the other hand, deep-buried dolomite reservoirs is formed by tectonic and hydrothermal reforming on initial dolomites. Therefore, the distribution of structure-controlled hydrothermal dolomite reservoirs is predicted in Tabei and Tazhong Area of Tarim Basin based on the geophysical data.

粘弹性介质中的地震波传播与波形反演研究

The real earth is far away from an ideal elastic ball. The movement of structures or fluid and scattering of thin-layer would inevitably affect seismic wave propagation, which is demonstrated mainly as energy nongeometrical attenuation. Today, most of theoretical researches and applications take the assumption that all media studied are fully elastic. Ignoring the viscoelastic property would, in some circumstances, lead to amplitude and phase distortion, which will indirectly affect extraction of traveltime and waveform we use in imaging and inversion. In order to investigate the response of seismic wave propagation and improve the imaging and inversion quality in complex media, we need not only consider into attenuation of the real media but also implement it by means of efficient numerical methods and imaging techniques. As for numerical modeling, most widely used methods, such as finite difference, finite element and pseudospectral algorithms, have difficulty in dealing with problem of simultaneously improving accuracy and efficiency in computation. To partially overcome this difficulty, this paper devises a matrix differentiator method and an optimal convolutional differentiator method based on staggered-grid Fourier pseudospectral differentiation, and a staggered-grid optimal Shannon singular kernel convolutional differentiator by function distribution theory, which then are used to study seismic wave propagation in viscoelastic media. Results through comparisons and accuracy analysis demonstrate that optimal convolutional differentiator methods can solve well the incompatibility between accuracy and efficiency, and are almost twice more accurate than the same-length finite difference. They can efficiently reduce dispersion and provide high-precision waveform data. On the basis of frequency-domain wavefield modeling, we discuss how to directly solve linear equations and point out that when compared to the time-domain methods, frequency-domain methods would be more convenient to handle the multi-source problem and be much easier to incorporate medium attenuation. We also prove the equivalence of the time- and frequency-domain methods by using numerical tests when assumptions with non-relaxation modulus and quality factor are made, and analyze the reason that causes waveform difference. In frequency-domain waveform inversion, experiments have been conducted with transmission, crosshole and reflection data. By using the relation between media scales and characteristic frequencies, we analyze the capacity of the frequency-domain sequential inversion method in anti-noising and dealing with non-uniqueness of nonlinear optimization. In crosshole experiments, we find the main sources of inversion error and figure out how incorrect quality factor would affect inverted results. When dealing with surface reflection data, several frequencies have been chosen with optimal frequency selection strategy, with which we use to carry out sequential and simultaneous inversions to verify how important low frequency data are to the inverted results and the functionality of simultaneous inversion in anti-noising. Finally, I come with some conclusions about the whole work I have done in this dissertation and discuss detailly the existing and would-be problems in it. I also point out the possible directions and theories we should go and deepen, which, to some extent, would provide a helpful reference to researchers who are interested in seismic wave propagation and imaging in complex media.

青藏高原东部电性结构特征及地球动力学意义

As the largest and highest plateau on the Earth, the Tibetan Plateau has been a key location for understanding the processes of mountain building and plateau formation during India-Asia continent-continent collision. As the front-end of the collision, the geological structure of eastern Tibetan Plateau is very complex. It is ideal as a natural laboratory for investigating the formation and evolution of the Tibetan Plateau. Institute of Geophysics, Chinese Academy of Sciences (CAS) carried out MT survey from XiaZayii to Qingshuihe in the east part of the plateau in 1998. After error analysis and distortion analysis, the Non-linear Conjugate Gradient inversion(NLCG), Rapid Relaxation Inversin (RRI) and 2D OCCAM Inversion algorithms were used to invert the data. The three models obtained from 3 algorithms provided similar electrical structure and the NLCG model fit the observed data better than the other two models. According to the analysis of skin depth, the exploration depth of MT in Tibet is much more shallow than in stable continent. For example, the Schmucker depth at period 100s is less than 50km in Tibet, but more than 100km in Canadian Shield. There is a high conductivity layer at the depth of several kilometers beneath middle Qiangtang terrane, and almost 30 kilometers beneath northern Qiangtang terrane. The sensitivity analysis of the data predicates that the depth and resistivity of the crustal high conductivity layer are reliable. The MT results provide a high conductivity layer at 20~40km depth, where the seismic data show a low velocity zone. The experiments show that the rock will dehydrate and partially melt in the relative temperature and pressure. Fluids originated from dehydration and partial melting will seriously change rheological characteristics of rock. Therefore, This layer with low velocity and high conductivity layer in the crust is a weak layer. There is a low velocity path at the depth of 90-110 km beneath southeastern Tibetan Plateau and adjacent areas from seismology results. The analysis on the temperature and rheological property of the lithosphere show that the low velocity path is also weak. GPS measurements and the numerical simulation of the crust-mantle deformation show that the movement rate is different for different terranes. The regional strike derived from decomposition analysis for different frequency band and seismic anisotropy indicate that the crust and upper mantle move separately instead of as a whole. There are material flow in the eastern and southeastern Tibetan Plateau. Therefore, the faults, the crustal and upper mantle weak layers are three different boundaries for relatively movement. Those results support the "two layer wedge plates" geodynamic model on Tibetan formation and evolution.