Deformation behaviours of coarse-grained and nanocrystalline Mg-5wt% Al alloys

Magnesium alloys have been of growing interest to various engineering applications, such as the automobile, aerospace, communication and computer industries due to their low density, high specific strength, good machineability and availability as compared with other structural materials. However, most Mg alloys suffer from poor plasticity due to their Hexagonal Close Packed structure. Grain refinement has been proved to be an effective method to enhance the strength and alter the ductility of the materials. Several methods have been proposed to produce materials with nanocrystalline grain structures. So far, most of the research work on nanocrystalline materials has been carried out on Face-Centered Cubic and Body-Centered Cubic metals. However, there has been little investigation of nanocrystalline Mg alloys. In this study, bulk coarse-grained and nanocrystalline Mg alloys were fabricated by a mechanical alloying method. The mixed powder of Mg chips and Al powder was mechanically milled under argon atmosphere for different durations of 0 hours (MA0), 10 hours (MA10), 20 hours (MA20), 30 hours (MA30) and 40 hours (MA40), followed by compaction and sintering. Then the sintered billets were hot-extruded into metallic rods with a 7 mm diameter. The obtained Mg alloys have a nominal composition of Mg–5wt% Al, with grain sizes ranging from 13 μm down to 50 nm, depending on the milling durations. The microstructure characterization and evolution after deformation were carried out by means of Optical microscopy, X-Ray Diffraction, Scanning Electron Microscopy, Transmission Electron Microscopy, Scanning Probe Microscopy and Neutron Diffraction techniques. Nanoindentaion, compression and micro-compression tests on micro-pillars were used to study the size effects on the mechanical behaviour of the Mg alloys. Two kinds of size effects on the mechanical behaviours and deformation mechanisms were investigated: grain size effect and sample size effect. The nanoindentation tests were composed of constant strain rate, constant loading rate and indentation creep tests. The normally reported indentation size effect in single crystal and coarse-grained crystals was observed in both the coarse-grained and nanocrystalline Mg alloys. Since the indentation size effect is correlated to the Geometrically Necessary Dislocations under the indenter to accommodate the plastic deformation, the good agreement between the experimental results and the Indentation Size Effect model indicated that, in the current nanocrystalline MA20 and MA30, the dislocation plasticity was still the dominant deformation mechanism. Significant hardness enhancement with decreasing grain size, down to 58 nm, was found in the nanocrystalline Mg alloys. Further reduction of grain size would lead to a drop in the hardness values. The failure of grain refinement strengthening with the relatively high strain rate sensitivity of nanocrystalline Mg alloys suggested a change in the deformation mechanism. Indentation creep tests showed that the stress exponent was dependent on the loading rate during the loading section of the indentation, which was related to the dislocation structures before the creep starts. The influence of grain size on the mechanical behaviour and strength of extruded coarse-grained and nanocrystalline Mg alloys were investigated using uniaxial compression tests. The macroscopic response of the Mg alloys transited from strain hardening to strain softening behaviour, with grain size reduced from 13 ìm to 50 nm. The strain hardening was related to the twinning induced hardening and dislocation hardening effect, while the strain softening was attributed to the localized deformation in the nanocrystalline grains. The tension–compression yield asymmetry was noticed in the nanocrystalline region, demonstrating the twinning effect in the ultra-fine-grained and nanocrystalline region. The relationship k tensions < k compression failed in the nanocrystalline Mg alloys; this was attributed to the twofold effect of grain size on twinning. The nanocrystalline Mg alloys were found to exhibit increased strain rate sensitivity with decreasing grain size, with strain rate ranging from 0.0001/s to 0.01/s. Strain rate sensitivity of coarse-grained MA0 was increased by more than 10 times in MA40. The Hall-Petch relationship broke down at a critical grain size in the nanocrystalline region. The breakdown of the Hall-Petch relationship and the increased strain rate sensitivity were due to the localized dislocation activities (generalization and annihilation at grain boundaries) and the more significant contribution from grain boundary mediated mechanisms. In the micro-compression tests, the sample size effects on the mechanical behaviours were studied on MA0, MA20 and MA40 micro-pillars. In contrast to the bulk samples under compression, the stress-strain curves of MA0 and MA20 micro-pillars were characterized with a number of discrete strain burst events separated by nearly elastic strain segments. Unlike MA0 and MA20, the stress-strain curves of MA40 micro-pillars were smooth, without obvious strain bursts. The deformation mechanisms of the MA0 and MA20 micro-pillars under micro-compression tests were considered to be initially dominated by deformation twinning, followed by dislocation mechanisms. For MA40 pillars, the deformation mechanisms were believed to be localized dislocation activities and grain boundary related mechanisms. The strain hardening behaviours of the micro-pillars suggested that the grain boundaries in the nanocrystalline micro-pillars would reduce the source (nucleation sources for twins/dislocations) starvation hardening effect. The power law relationship of the yield strength on pillar dimensions in MA0, MA20 supported the fact that the twinning mechanism was correlated to the pre-existing defects, which can promote the nucleation of the twins. Then, we provided a latitudinal comparison of the results and conclusions derived from the different techniques used for testing the coarse-grained and nanocrystalline Mg alloy; this helps to better understand the deformation mechanisms of the Mg alloys as a whole. At the end, we summarized the thesis and highlighted the conclusions, contributions, innovations and outcomes of the research. Finally, it outlined recommendations for future work.

Private supervisors of learner drivers and Queensland's graduated driver licensing system : how important are they?

Background: A key element of graduated driver licensing systems is the level of support provided by parents. In mid-2007 changes were made to Queensland’s graduated driver licensing system, including amendments to the learner licence with one of the more significant changes requiring learners to record 100 hours of supervised driving practice in a logbook. Prior to mid-2007, there was no minimum supervision requirement. Aims: The aim of this study was to document the experiences of the supervisors of Queensland learner drivers after the changes made to the graduated driver licensing system in mid-2007. Methods: The sample of 552 supervisors of learner drivers was recruited using a combination of convenience and snowball sampling techniques. The internet survey was open for completion between July 2009 and May 2010 and took approximately 15 to 20 minutes for participants to complete. Results: For 59.7 per cent of the participants, this was the first time that they had supervised a learner driver. For 63.2 per cent, they classified themselves as the main supervisor for the learner driver. Participants provided an average of 79.62 hours of supervision (sd = 92.38), while other private supervisors provided 34.89 hours of supervision (sd = 41.74) to the same learner and professional driving instructors 18.55 hours of supervision (sd = 27.54). The vast majority of supervisors recorded all or most of the practice that they provided their learner driver in their log book with most supervisors indicating that they believed that the hours recorded in the learner’s logbook were either accurate or very accurate. While many supervisors stated that they did not receive any advice regarding the supervision of learner drivers, some had received advice from others such as friends or through discussions with a professional driving instructor. Discussion and conclusions: While graduated driver licensing systems implicitly encourage the involvement of parents and other private supervisors, these people tend not to be systematically involved. As demonstrated in this study, private supervisors provide a significant amount of supervised practice and seek to record this practice accurately and honestly in the learner’s logbook. However, even though a significant number of participants reported that this was the first time that they had supervised a learner driver, they accessed little support or guidance for their role. This suggests a need to more overtly encourage and support the role of private supervisors for learner drivers.

Effects of disclosure of sexual identity at work for gay, lesbian, bisexual, transgender and intersex (GLBTI) employees in Queensland

All Australian businesses are governed by legislation aiming to prevent workplace discrimination based on sexual orientation and sexual identity and serious penalties apply to companies found contravening legislation. While other Australian studies have examined these issues, Queensland has either not been included or relevant data is not easily identified. This paper presents the results of an exploratory study using a quantitative survey to determine the consequences of disclosure of a person’s sexual orientation or gender identity to colleagues in workplaces in Queensland. Results suggest GLBTI workers are disclosing their sexuality more and are experiencing more discrimination in the workplace, despite anti-discrimination policies. This suggests the need to further investigate companies’ compliance with workplace legislation.

Spatial/surveying programs repositioning within new STEM Faculty at QUT

Many of the undergraduate and postgraduate programs of the former Faculty of Built Environment and Engineering PLUS Faculty of Sciences and Technology are changing as a result of merging these two large organisations, with some disciplines relocating to faculties of Creative Industries and Health respectively. The new STEM precinct under construction has begun rising from the proverbial hole-in-the-ground. Existing Surveying and Spatial Sciences programs, assets and staff are being repositioned with the newly formed School of Earth, Environment and Biological Sciences.2011. Golden graduates morning tea organised by QUT Alumni. Technology upgrades to the Mapping Sciences lab benefits 3-D learning experiences. Second and third-year students are undertaking Work Integrated Learning (WIL) over the summer vacation period. Final year students recently presented capstone project presentations at mini-conference in the Gibson Rooms overlooking a vibrant Southbank and sparkling Brisbane River. Discussion on end of year graduation ceremony held at QPAC.

Iron biogeochemistry and associated greenhouse gas evolution in a forested subtropical Australian coastal catchment : Poona Creek, Southeast Queensland

Iron (Fe) is the fourth most abundant element in the Earth’s crust. Excess Fe mobilization from terrestrial into aquatic systems is of concern for deterioration of water quality via biofouling and nuisance algal blooms in coastal and marine systems. Substantial Fe dissolution and transport involve alternate Fe(II) oxidation followed by Fe(III) reduction, with a diversity of Bacteria and Archaea acting as the key catalyst. Microbially-mediated Fe cycling is of global significance with regard to cycles of carbon (C), sulfur (S) and manganese (Mn). However, knowledge regarding microbial Fe cycling in circumneutral-pH habitats that prevail on Earth has been lacking until recently. In particular, little is known regarding microbial function in Fe cycling and associated Fe mobilization and greenhouse (CO2 and CH4, GHG) evolution in subtropical Australian coastal systems where microbial response to ambient variations such as seasonal flooding and land use changes is of concern. Using the plantation-forested Poona Creek catchment on the Fraser Coast of Southeast Queensland (SEQ), this research aimed to 1) study Fe cycling-associated bacterial populations in diverse terrestrial and aquatic habitats of a representative subtropical coastal circumneutral-pH (4–7) ecosystem; and 2) assess potential impacts of Pinus plantation forestry practices on microbially-mediated Fe mobilization, organic C mineralization and associated GHG evolution in coastal SEQ. A combination of wet-chemical extraction, undisturbed core microcosm, laboratory bacterial cultivation, microscopy and 16S rRNA-based molecular phylogenetic techniques were employed. The study area consisted primarily of loamy sands, with low organic C and dissolved nutrients. Total reactive Fe was abundant and evenly distributed within soil 0–30 cm profiles. Organic complexation primarily controlled Fe bioavailability and forms in well-drained plantation soils and water-logged, native riparian soils, whereas tidal flushing exerted a strong “seawater effect” in estuarine locations and formed a large proportion of inorganic Fe(III) complexes. There was a lack of Fe(II) sources across the catchment terrestrial system. Mature, first-rotation plantation clear-felling and second-rotation replanting significantly decreased organic matter and poorly crystalline Fe in well-drained soils, although variations in labile soil organic C fractions (dissolved organic C, DOC; and microbial biomass C, MBC) were minor. Both well-drained plantation soils and water-logged, native-vegetation soils were inhabited by a variety of cultivable, chemotrophic bacterial populations capable of C, Fe, S and Mn metabolism via lithotrophic or heterotrophic, (micro)aerobic or anaerobic pathways. Neutrophilic Fe(III)-reducing bacteria (FeRB) were most abundant, followed by aerobic, heterotrophic bacteria (heterotrophic plate count, HPC). Despite an abundance of FeRB, cultivable Fe(II)-oxidizing bacteria (FeOB) were absent in associated soils. A lack of links between cultivable Fe, S or Mn bacterial densities and relevant chemical measurements (except for HPC correlated with DOC) was likely due to complex biogeochemical interactions. Neither did variations in cultivable bacterial densities correlate with plantation forestry practices, despite total cultivable bacterial densities being significantly lower in estuarine soils when compared with well-drained plantation soils and water-logged, riparian native-vegetation soils. Given that bacterial Fe(III) reduction is the primary mechanism of Fe oxide dissolution in soils upon saturation, associated Fe mobilization involved several abiotic and biological processes. Abiotic oxidation of dissolved Fe(II) by Mn appeared to control Fe transport and inhibit Fe dissolution from mature, first-rotation plantation soils post-saturation. Such an effect was not observed in clear-felled and replanted soils associated with low SOM and potentially low Mn reactivity. Associated GHG evolution post-saturation mainly involved variable CO2 emissions, with low, but consistently increasing CH4 effluxes in mature, first-rotation plantation soil only. In comparison, water-logged soils in the riparian native-vegetation buffer zone functioned as an important GHG source, with high potentials for Fe mobilization and GHG, particularly CH4 emissions in riparian loam soils associated with high clay and crystalline Fe fractions. Active Fe–C cycling was unlikely to occur in lower-catchment estuarine soils associated with low cultivable bacterial densities and GHG effluxes. As a key component of bacterial Fe cycling, neutrophilic FeOB widely occurred in diverse aquatic, but not terrestrial, habitats of the catchment study area. Stalked and sheathed FeOB resembling Gallionella and Leptothrix were limited to microbial mat material deposited in surface fresh waters associated with a circumneutral-pH seep, and clay-rich soil within riparian buffer zones. Unicellular, Sideroxydans-related FeOB (96% sequence identity) were ubiquitous in surface and subsurface freshwater environments, with highest abundance in estuary-adjacent shallow coastal groundwater water associated with redox transition. The abundance of dissolved C and Fe in the groundwater-dependent system was associated with high numbers of cultivable anaerobic, heterotrophic FeRB, microaerophilic, putatively lithotrophic FeOB and aerobic, heterotrophic bacteria. This research represents the first study of microbial Fe cycling in diverse circumneutral-pH environments (terrestrial–aquatic, freshwater–estuarine, surface–subsurface) of a subtropical coastal ecosystem. It also represents the first study of its kind in the southern hemisphere. This work highlights the significance of bacterial Fe(III) reduction in terrestrial, and bacterial Fe(II) oxidation in aquatic catchment Fe cycling. Results indicate the risk of promotion of Fe mobilization due to plantation clear-felling and replanting, and GHG emissions associated with seasonal water-logging. Additional significant outcomes were also achieved. The first direct evidence for multiple biomineralization patterns of neutrophilic, microaerophilic, unicellular FeOB was presented. A putatively pure culture, which represents the first cultivable neutrophilic FeOB from the southern hemisphere, was obtained as representative FeOB ubiquitous in diverse catchment aquatic habitats.

Human-specific E. coli single nucleotide polymorphism (SNP) genotypes detected in a South-East Queensland waterway, Australia

The World Health Organization recommends that the majority of water monitoring laboratories in the world should test for E. coli daily since thermotolerant coliforms and E. coli are key indicators for risk assessment of recreational waters. Recently, we developed a new SNP method for typing E. coli strains, by which human-specific genotypes were identified. Here, we report the presence of these previously described specific SNP profiles in environmental water, sourced from the Coomera River, located on South East Queensland, Australia, over a period of two years. This study tested for the presence of human-specific E. coli to ascertain whether hydrologic and anthropogenic activity plays a key role in the pollution of the investigated watershed or whether the pollution is from other sources. We found six human-specific SNP profiles and one animal-specific SNP profile consistently across sampling sites and times. We have demonstrated that our SNP genotyping method is able to rapidly identify and characterise human- and animal-specific E. coli isolates in water sources.

SNP diversity of Enterococcus faecalis and Enterococcus faecium in a South East Queensland waterway, Australia, and associated antibiotic resistance gene profiles

BACKGROUND: Enterococcus faecalis and Enterococcus faecium are associated with faecal pollution of water, linked to swimmer-associated gastroenteritis and demonstrate a wide range of antibiotic resistance. The Coomera River is a main water source for the Pimpama-Coomera watershed and is located in South East Queensland, Australia, which is used intensively for agriculture and recreational purposes. This study investigated the diversity of E. faecalis and E. faecium using Single Nucleotide Polymorphisms (SNPs) and associated antibiotic resistance profiles. RESULTS: Total enterococcal counts (cfu/ml) for three/six sampling sites were above the United States Environmental Protection Agency (USEPA) recommended level during rainfall periods and fall into categories B and C of the Australian National Health and Medical Research Council (NHMRC) guidelines (with a 1-10% gastrointestinal illness risk). E. faecalis and E. faecium isolates were grouped into 29 and 23 SNP profiles (validated by MLST analysis) respectively. This study showed the high diversity of E. faecalis and E. faecium over a period of two years and both human-related and human-specific SNP profiles were identified. 81.8% of E. faecalis and 70.21% of E. faecium SNP profiles were associated with genotypic and phenotypic antibiotic resistance. Gentamicin resistance was higher in E. faecalis (47% resistant) and harboured the aac(6')-aph(2') gene. Ciprofloxacin resistance was more common in E. faecium (12.7% resistant) and gyrA gene mutations were detected in these isolates. Tetracycline resistance was less common in both species while tet(L) and tet(M) genes were more prevalent. Ampicillin resistance was only found in E. faecium isolates with mutations in the pbp5 gene. Vancomycin resistance was not detected in any of the isolates. We found that antibiotic resistance profiles further sub-divided the SNP profiles of both E. faecalis and E. faecium. CONCLUSIONS: The distribution of E. faecalis and E. faecium genotypes is highly diverse in the Coomera River. The SNP genotyping method is rapid and robust and can be applied to study the diversity of E. faecalis and E. faecium in waterways. It can also be used to test for human-related and human-specific enterococci in water. The resolving power can be increased by including antibiotic-resistant profiles which can be used as a possible source tracking tool. This warrants further investigation.

An evaluation of the sustainability of agreements reached through mediations conducted by the dispute resolution centres of the Department of Justice and Attorney General, Queensland between 1999 to 2003

In 1990 the Dispute Resolution Centres Act, 1990 (Qld) (the Act) was passed by the Queensland Parliament. In the second reading speech for the Dispute Resolution Centres Bill on May 1990 the Hon Dean Wells stated that the proposed legislation would make mediation services available “in a non-coercive, voluntary forum where, with the help of trained mediators, the disputants will be assisted towards their own solutions to their disputes, thereby ensuring that the result is acceptable to the parties” (Hansard, 1990, 1718). It was recognised at that time that a method for resolving disputes was necessary for which “the conventional court system is not always equipped to provide lasting resolution” (Hansard, 1990, 1717). In particular, the lasting resolution of “disputes between people in continuing relationships” was seen as made possible through the new legislation; for example, “domestic disputes, disputes between employees, and neighbourhood disputes relating to such issues as overhanging tree branches, dividing fences, barking dogs, smoke, noise and other nuisances are occurring continually in the community” (Hansard, 1990, 1717). The key features of the proposed form of mediation in the Act were articulated as follows: “attendance of both parties at mediation sessions is voluntary; a party may withdraw at any time; mediation sessions will be conducted with as little formality and technicality as possible; the rules of evidence will not apply; any agreement reached is not enforceable in any court; although it could be made so if the parties chose to proceed that way; and the provisions of the Act do not affect any rights or remedies that a party to a dispute has apart from the Act” (Hansard, 1990, 1718). Since the introduction of the Act, the Alternative Dispute Resolution Branch of the Queensland Department of Justice and Attorney General has offered mediation services through, first the Community Justice Program (CJP), and then the Dispute Resolution Centres (DRCs) for a range of family, neighbourhood, workplace and community disputes. These services have mirrored those available through similar government agencies in other states such as the Community Justice Centres of NSW and the Victorian Dispute Resolution Centres. Since 1990, mediation has become one of the fastest growing forms of alternative dispute resolution (ADR). Sourdin has commented that "In addition to the growth in court-based and community-based dispute resolution schemes, ADR has been institutionalised and has grown within Australia and overseas” (2005, 14). In Australia, in particular, the development of ADR service provision “has been assisted by the creation and growth of professional organisations such as the Leading Edge Alternative Dispute Resolvers (LEADR), the Australian Commercial Dispute Centres (ACDC), Australian Disputes Resolution Association (ADRA), Conflict Resolution Network, and the Institute of Arbitrators and Mediators Australia (IAMA)” (Sourdin, 2005, 14). The increased emphasis on the use of ADR within education contexts (particularly secondary and tertiary contexts) has “also led to an increasing acceptance and understanding of (ADR) processes” (Sourdin, 2005, 14). Proponents of the mediation process, in particular, argue that much of its success derives from the inherent flexibility and creativity of the agreements reached through the mediation process and that it is a relatively low cost option in many cases (Menkel-Meadow, 1997, 417). It is also accepted that one of the main reasons for the success of mediation can be attributed to the high level of participation by the parties involved and thus creating a sense of ownership of, and commitment to, the terms of the agreement (Boulle, 2005, 65). These characteristics are associated with some of the core values of mediation, particularly as practised in community-based models as found at the DRCs. These core values include voluntary participation, party self-determination and party empowerment (Boulle, 2005, 65). For this reason mediation is argued as being an effective approach to resolving disputes, that creates a lasting resolution of the issues. Evaluation of the mediation process, particularly in the context of the growth of ADR, has been an important aspect of the development of the process (Sourdin, 2008). Writing in 2005 for example, Boulle, states that “although there is a constant refrain for more research into mediation practice, there has been a not insignificant amount of mediation measurement, both in Australia and overseas” (Boulle, 2005, 575). The positive claims of mediation have been supported to a significant degree by evaluations of the efficiency and effectiveness of the process. A common indicator of the effectiveness of mediation is the settlement rate achieved. High settlement rates for mediated disputes have been found for Australia (Altobelli, 2003) and internationally (Alexander, 2003). Boulle notes that mediation agreement rates claimed by service providers range from 55% to 92% (Boulle, 2005, 590). The annual reports for the Alternative Dispute Resolution Branch of the Queensland Department of Justice and Attorney-General considered prior to the commencement of this study indicated generally achievement of an approximate settlement figure of 86% by the Queensland Dispute Resolution Centres. More recently, the 2008-2009 annual report states that of the 2291 civil dispute mediated in 2007-2008, 86% reached an agreement. Further, of the 2693 civil disputes mediated in 2008-2009, 73% reached an agreement. These results are noted in the report as indicating “the effectiveness of mediation in resolving disputes” and as reflecting “the high level of agreement achieved for voluntary mediations” (Annual Report, 2008-2009, online). Whilst the settlement rates for the DRCs are strong, parties are rarely contacted for long term follow-up to assess whether agreements reached during mediation lasted to the satisfaction of each party. It has certainly been the case that the Dispute Resolution Centres of Queensland have not been resourced to conduct long-term follow-up assessments of mediation agreements. As Wade notes, "it is very difficult to compare "success" rates” and whilst “politicians want the comparison studies (they) usually do not want the delay and expense of accurate studies" (1998, 114). To date, therefore, it is fair to say that the efficiency of the mediation process has been evaluated but not necessarily its effectiveness. Rather, the practice at the Queensland DRCs has been to evaluate the quality of mediation service provision and of the practice of the mediation process. This has occurred, for example, through follow-up surveys of parties' satisfaction rates with the mediation service. In most other respects it is fair to say that the Centres have relied on the high settlement rates of the mediation process as a sign of the effectiveness of mediation (Annual Reports 1991 - 2010). Research of the mediation literature conducted for the purpose of this thesis has also indicated that there is little evaluative literature that provides an in-depth analysis and assessment of the longevity of mediated agreements. Instead evaluative studies of mediation tend to assess how mediation is conducted, or compare mediation with other conflict resolution options, or assess the agreement rate of mediations, including parties' levels of satisfaction with the service provision of the dispute resolution service provider (Boulle, 2005, Chapter 16).

Resilience of a corrupt police network : the first and second jokes in Queensland

Resilient organised crime groups survive and prosper despite law enforcement activity, criminal competition and market forces. Corrupt police networks, like any other crime network, must contain resiliency characteristics if they are to continue operation and avoid being closed down through detection and arrest of their members. This paper examines the resilience of a large corrupt police network, namely The Joke which operated in the Australian state of Queensland for a number of decades. The paper uses social network analysis tools to determine the resilient characteristics of the network. This paper also assumes that these characteristics will be different to those of mainstream organised crime groups because the police network operates within an established policing agency rather than as an independent entity hiding within the broader community.

Characteristics of new Queensland cyclists

Various state and local government initiatives have been implemented to encourage Australians to ride bicycles. Decreasing the number of trips taken by motor vehicle has benefits for the both the individual and the community, including health, congestion and environmental benefits. This research examined who the new cyclists are, how much and where they ride.

The validation of the rating for subdivision neighbourhood sustainability design (RSNSD) In Bangkok Metropolitan Region (BMR), Thailand

In recent years, the problems resulting from unsustainable subdivision development have become significant problems in the Bangkok Metropolitan Region (BMR), Thailand. Numbers of government departments and agencies have tried to eliminate the problems by introducing the rating tools to encourage the higher sustainability levels of subdivision development in BMR, such as the Environmental Impact Assessment Monitoring Award (EIA-MA) and the Thai’s Rating for Energy and Environmental Sustainability of New construction and major renovation (TREES-NC). However, the EIA-MA has included the neighbourhood designs in the assessment criteria, but this requirement applies to large projects only. Meanwhile, TREES-NC has focused only on large scale buildings such as condominiums, office buildings, and is not specific for subdivision neighbourhood designs. Recently, the new rating tool named “Rating for Subdivision Neighbourhood Sustainability Design (RSNSD)” has been developed. Therefore, the validation process of RSNSD is still required. This paper aims to validate the new rating tool for subdivision neighbourhood design in BMR. The RSNSD has been validated by applying the rating tool to eight case study subdivisions. The result of RSNSD by data generated through surveying subdivisions will be compared to the existing results from the EIA-MA. The selected cases include of one “Excellent Award”, two “Very Good Award”, and five non-rated subdivision developments. This paper expects to prove the credibility of RSNSD before introducing to the real subdivision development practises. The RSNSD could be useful to encourage higher sustainability subdivision design level, and then protect the problems from further subdivision development in BMR.

Influence of physical and chemical properties of solids on heavy metal adsorption

Partition of heavy metals between particulate and dissolve fraction of stormwater primarily depends on the adsorption characteristics of solids particles. Moreover, the bioavailability of heavy metals is also influenced by the adsorption behaviour of solids. However, due to the lack of fundamental knowledge in relation to the heavy metals adsorption processes of road deposited solids, the effectiveness of stormwater management strategies can be limited. The research study focused on the investigation of the physical and chemical parameters of solids on urban road surfaces and, more specifically, on heavy metal adsorption to solids. Due to the complex nature of heavy metal interaction with solids, a substantial database was generated through a series of field investigations and laboratory experiments. The study sites for the build-up pollutant sample collection were selected from four urbanised suburbs located in a major river catchment. Sixteen road sites were selected from these suburbs and represented typical industrial, commercial and residential land uses. Build-up pollutants were collected using a wet and dry vacuum collection technique which was specially designed to improve fine particle collection. Roadside soil samples were also collected from each suburb for comparison with the road surface solids. The collected build-up solids samples were separated into four particle size ranges and tested for a range of physical and chemical parameters. The solids build-up on road surfaces contained a high fraction (70%) of particles smaller than 150ìm, which are favourable for heavy metal adsorption. These solids particles predominantly consist of soil derived minerals which included quartz, albite, microcline, muscovite and chlorite. Additionally, a high percentage of amorphous content was also identified in road deposited solids. In comparing the mineralogical data of surrounding soil and road deposited solids, it was found that about 30% of the solids consisted of particles generated from traffic related activities on road surfaces. Significant difference in mineralogical composition was noted in different particle sizes of build-up solids. Fine solids particles (<150ìm) consisted of a clayey matrix and high amorphous content (in the region of 40%) while coarse particles (>150ìm) consisted of a sandy matrix at all study sites, with about 60% quartz content. Due to these differences in mineralogical components, particles larger than and smaller than 150ìm had significant differences in their specific surface area (SSA) and effective cation exchange capacity (ECEC). These parameters, in turn, exert a significant influence on heavy metal adsorption. Consequently, heavy metal content in >150ìm particles was lower than in the case of fine particles. The particle size range <75ìm had the highest heavy metal content, corresponding with its high clay forming minerals, high organic matter and low quartz content which increased the SSA, ECEC and the presence of Fe, Al and Mn oxides. The clay forming minerals, high organic matter and Fe, Al and Mn oxides create distinct groups of charge sites on solids surfaces and exhibit different adsorption mechanisms and bond strength, between heavy metal elements and charge sites. Therefore, the predominance of these factors in different particle sizes leads to different heavy metal adsorption characteristics. Heavy metals show preference for association with clay forming minerals in fine solids particles, whilst in coarse particles heavy metals preferentially associate with organic matter. Although heavy metal adsorption to amorphous material is very low, the heavy metals embedded in traffic related materials have a potential impact on stormwater quality.Adsorption of heavy metals is not confined to an individual type of charge site in solids, whereas specific heavy metal elements show preference for adsorption to several different types of charge sites in solids. This is attributed to the dearth of preferred binding sites and the inability to reach the preferred binding sites due to competition between different heavy metal species. This confirms that heavy metal adsorption is significantly influenced by the physical and chemical parameters of solids that lead to a heterogeneity of surface charge sites. The research study highlighted the importance of removal of solids particles from stormwater runoff before they enter into receiving waters to reduce the potential risk posed by the bioavailability of heavy metals. The bioavailability of heavy metals not only results from the easily mobile fraction bound to the solids particles, but can also occur as a result of the dissolution of other forms of bonds by chemical changes in stormwater or microbial activity. Due to the diversity in the composition of the different particle sizes of solids and the characteristics and amount of charge sites on the particle surfaces, investigations using bulk solids are not adequate to gain an understanding of the heavy metal adsorption processes of solids particles. Therefore, the investigation of different particle size ranges is recommended for enhancing stormwater quality management practices.

Big, bigger, best? The impact of reforms on the not-for-profit sector in Queensland

Organisations within the not-for-profit sector provide services to individuals and groups that government and for-profit organisations cannot or will not consider. The not-for-profit sector has come to be a vibrant and rich agglomeration of services and programs that operate under a myriad of philosophical stances, service orientation, client groupings and operational capacities. In Australia these organisations and services are providing social support and service assistance to many people in the community; often targeting their assistance to the most difficult of clients. Initially, in undertaking this role, the not-for-profit sector received limited sponsorship from government. Over time governments assumed greater responsibility in the form of service grants to particular groups: ‘the worthy poor’. More recently, they have entered into contractual service agreements with the not-for-profit sector, which specify the nature of the outcomes to be achieved and, to a degree, the way in which the services will be provided. A consequence of this growing shift to a more marketised model of service contracting, often offered-up under the label of enhanced collaborative practice, has been increased competitiveness between agencies that had previously worked well together (Keast and Brown, 2006). Another trend emerging from the market approach is the entrance of for-profit providers. These larger organisations have higher levels of organisational capacity with considerable organisational slack to allow them to adopt new service roles. Shaped almost as ‘shadow governments’ they appear to be a strong preference for governments looking for greater accountability of outcomes and an easier way to control the interaction with the conventional not-for-profit sector. The question is will governments’ apparent preference for larger organisational arrangements lead to the demise of the vibrancy of the not-for-profit sector and impact on service provision to those people who fall outside of the remit of the new service providers? To address this issue, this paper uses information gleaned from a state-wide survey of not-for-profit organisations in Queensland, Australia which included organisational size, operational scope, funding arrangements and governance/management approaches. Supplementing this information is qualitative data derived from 17 focus groups and 120 interviews conducted over ten years of study of this sector. The findings contribute to greater understanding of the practice and theory of the future provision of social services.