Análise morfológica da placenta da paca (Agouti paca, Linnaeus, 1766: Estudo ao microscópio de luz e à microscopia eletrônica de transmissão

Foram estudados os aspectos morfológicos de nove placentas de paca (Agouti paca, L., 1766) mediante análises em microscopia de luz e eletrônica de transmissão dos fragmentos teciduais correspondentes à porção de maior conexão placentária em diferentes fêmeas gestantes, nos estágios intermediário e final da prenhez. Realizamos este estudo, pois, aliada à necessidade da procura de novas espécies que atuem como modelos experimentais adequados, havia a disponibilidade deste roedor em nosso meio; por outro lado, o melhor conhecimento dos aspectos reprodutivos destes animais oferece subsídios ao estabelecimento de criatórios racionais desta espécie, uma vez que a preservação deste vertebrado é necessária, além do grande interesse comercial em torno de sua carne. Os resultados mostraram que este roedor possui uma placenta do tipo vitelina e outra do tipo corioalantoidiana, sendo este órgão do tipo hemocorial, labiríntico, que se apresenta histologicamente composto por lóbulos divididos em três regiões distintas: o centro do lóbulo, o labirinto e o interlóbulo. Na região do centro do lóbulo, verificou-se a presença de artérias e veias; e em sua região periférica estavam presentes dois sistemas tubulares arranjados de forma paralela, onde as lacunas sangüíneas e os capilares estavam em íntimo contato, formando a região do labirinto. O interlóbulo era composto de artérias e veias. O trofoblasto era o principal componente da placenta, que, independentemente da região onde se encontrava, mostrava-se de natureza sincicial. Ultra-estruturalmente a barreira placentária da paca foi classificada como hemomonocorial.

Avaliação do potencial fisiológico de lotes de sementes de soja

Vários procedimentos são utilizados para avaliar o potencial fisiológico de sementes, sendo fundamental a utilização daqueles que reflitam melhor o desempenho em campo. A pesquisa teve como objetivo avaliar o potencial fisiológico de sementes de soja por meio de testes de avaliação rápida, de vigor, de emergência de plântulas em campo e análise computadorizada de imagens (SVIS®), procurando identificar o procedimento mais eficiente na separação de lotes. Cinco lotes das cultivares BRS Valiosa RR e CD 208 foram avaliados em duas épocas (antes e após armazenamento) pelos testes de germinação, de avaliação rápida (embebição em água e pH do exsudato), de vigor (envelhecimento acelerado e condutividade elétrica), de emergência de plântulas em campo e análise computadorizada de imagens (SVIS®). Os testes de germinação em areia, de condutividade elétrica e de embebição em água foram eficientes na separação dos lotes, mas apenas este último possibilitou identificar diferenças consistentes entre os lotes nos dois períodos avaliados. Assim, o teste de embebição em água pode ser considerado promissor na composição de programas de controle de qualidade.

Estimates of genetic parameters for scrotal circumference using random regression models in Nelore cattle

A total of 15,901 scrotal circumference (SC) records from 5300 Nelore bulls, ranging from 229 to 560 days of age, were used with the objective of estimating (co)variance functions for SC, using random regression models. Models included the fixed effects of contemporary group and age of dam at calving as covariable (linear and quadratic effects). To model the population mean trend, a third order Legendre polynomial on animal age was utilized. The direct additive genetic and animal permanent environmental random effects were modeled by Legendre polynomials on animal age, with orders of fit ranging from 1 to 5. Residual variances were modeled considering 1 (homogeneity of variance) or 4 age classes. Results obtained with the random regression models were compared to multi-trait analysis. (Co)variance estimates using multi-trait and random regression models were similar. The model considering a third- and fifth-order Legendre polynomials for additive genetic and animal permanent environmental effects, respectively, was the most adequate to model changes in variance of SC with age. Heritability estimates for SC ranged from 0.24 (229 days of age) to 0.47 (300 days of age), remained almost constant until 500 days of age (0.52), decreasing thereafter (0.44). In general, the genetic correlations between measures of scrotal circumference obtained from 229 to 560 days of age decreased with increasing distance between ages. For genetic evaluation scrotal circumference could be measured between 400 and 500 days of age. (C) 2010 Elsevier B.V. All rights reserved.

Grapevine root distribution in drip and microsprinkler irrigation

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Distribuição radicular de cultivares de aspargo em áreas irrigadas de Petrolina - PE

A distribuição radicular de duas cultivares de aspargo (New Jersey 220 e UC 157 F1), irrigadas por aspersão convencional, foi avaliada durante o ano de 1997 em solos de textura arenosa, em plantio experimental e comercial, respectivamente, nos Projetos de Irrigação de Bebedouro e Senador Nilo Coelho, em Petrolina (PE). O objetivo foi obter informações do sistema radicular do aspargo, empregando-se os métodos do monolito e do perfil de solo auxiliado pela análise de imagens digitais, para o manejo de solo e água nesse cultivo. Na área experimental, a maior parte da matéria seca, área e comprimento de raízes no perfil de solo e densidade de comprimento radicular foram encontradas até a profundidade de 0,4 m nas duas cultivares, enquanto que na comercial a maior parte da área e comprimento de raízes no perfil do solo estendeu-se até a profundidade de 0,6 m (cv. New Jersey 220). Nesses dois plantios, as raízes das cultivares atingiram a profundidade de 1 m. Na área experimental, a massa seca, a área e o comprimento no perfil de solo, e a densidade de comprimento radicular nas cultivares concentraram-se até a distância de 0,6 m à linha de plantas. No intervalo de diâmetro (d) de raízes 2imagens, o diâmetro de raízes variou entre 2,4 e 2,6 mm (cv. New Jersey 220) e 2,4 e 3,6 mm (cv. UC 157 F1). As estimativas da distribuição e do diâmetro radicular apresentaram similaridades considerando os métodos empregados.

Análise da imagem digital para estimativa da área foliar em plantas de laranja Pêra

Objetivou-se, com o trabalho, avaliar dois métodos de estimativa da área foliar, em plantas de laranja Pêra, pela análise da imagem digital obtida com scanner e câmera fotográfica digital. Para determinar a área das folhas, um grupo de discos foi colocado sobre um leitor de scanner, sendo que a imagem obtida foi armazenada. Os mesmos grupos de discos foram fixados sobre cartolina branca e fotografados com câmera fotográfica digital. As imagens obtidas da câmera fotográfica e do scanner foram processadas utilizando ferramentas de um editor de imagem que permite a contagem de pixels de determinada cor, no caso verde. Para a comparação dos métodos, os discos foram submetidos a integrador óptico de área foliar modelo LICOR-3100, utilizando os mesmos agrupamentos. Foram coletadas 20 folhas (cinco em cada quadrante da planta) por parcela de um experimento para comparação de fertilizantes comerciais e doses de zinco, aplicados via foliar, em plantas de sete anos de idade. O experimento foi composto de sete tratamentos e quatro repetições, num total de 28 parcelas. Os dois métodos apresentaram alta correlação com a área estimada pelo integrador óptico de área, considerado como método de referência. O método da análise da imagem obtida com câmera fotográfica, na resolução de 5.0 megapixel, foi mais precisa quando comparada à área estimada pelo integrador óptico de área.

Metodologia de análise e diagnóstico de fratura em um componente automotivo sujeito a cargas cíclicas alternadas

The competitiveness of the trade generated by the higher availability of products with lower quality and cost promoted a new reality of industrial production with small clearances. Track deviations at the production are not discarded, uncertainties can statistically occur. The world consumer and the Brazilian one are supported by the consumer protection code, in lawsuits against the products poor quality. An automobile is composed of various systems and thousands of constituent parts, increasing the likelihood of failure. The dynamic and security systems are critical in relation to the consequences of possible failures. The investigation of the failure gives us the possibility of learning and contributing to various improvements. Our main purpose in this work is to develop a systematic, specific methodology by investigating the root cause of the flaw occurred on an axle end of the front suspension of an automobile, and to perform comparative data analyses between the fractured part and the project information. Our research was based on a flaw generated in an automotive suspension system involved in a mechanical judicial cause, resulting in property and personal damages. In the investigations concerning the analysis of mechanical flaws, knowledge on materials engineering plays a crucial role in the process, since it enables applying techniques for characterizing materials, relating the technical attributes required from a respective part with its structure of manufacturing material, thus providing a greater scientific contribution to the work. The specific methodology developed follows its own flowchart. In the early phase, the data in the records and information on the involved ones were collected. The following laboratory analyses were performed: macrography of the fracture, micrography with SEM (Scanning Electron Microscope) of the initial and final fracture, phase analysis with optical microscopy, Brinell hardness and Vickers microhardness analyses, quantitative and qualitative chemical analysis, by using X-ray fluorescence and optical spectroscopy for carbon analysis, qualitative study on the state of tension was done. Field data were also collected. In the analyses data of the values resulting from the fractured stock parts and the design values were compared. After the investigation, one concluded that: the developed methodology systematized the investigation and enabled crossing data, thus minimizing diagnostic error probability, the morphology of the fracture indicates failure by the fatigue mechanism in a geometrically propitious location, a tension hub, the part was subjected to low tensions by the sectional area of the final fracture, the manufacturing material of the fractured part has low ductility, the component fractured in an earlier moment than the one recommended by the manufacturer, the percentages of C, Si, Mn and Cr of the fractured part present values which differ from the design ones, the hardness value of the superior limit of the fractured part is higher than that of the design, and there is no manufacturing uniformity between stock and fractured part. The work will contribute to optimizing the guidance of the actions in a mechanical engineering judicial expertise

Extração semiautomática de contornos de telhado de edifícios com base em snakes e programação dinâmica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Predição de sombras de edifícios sobre vias urbanas com base em modelos digitais de elevações e dados de imagens aéreas de alta resolução

This research presents a methodology for prediction of building shadows cast on urban roads existing on high-resolution aerial imagery. Shadow elements can be used in the modeling of contextual information, whose use has become more and more common in image analysis complex processes. The proposed methodology consists in three sequential steps. First, the building roof contours are manually extracted from an intensity image generated by the transformation of a digital elevation model (DEM) obtained from airborne laser scanning data. In similarly, the roadside contours are extracted, now from the radiometric information of the laser scanning data. Second, the roof contour polygons are projected onto the adjacent roads by using the parallel projection straight lines, whose directions are computed from the solar ephemeris, which depends on the aerial image acquisition time. Finally, parts of shadow polygons that are free from building perspective obstructions are determined, given rise to new shadow polygons. The results obtained in the experimental evaluation of the methodology showed that the method works properly, since it allowed the prediction of shadow in high-resolution imagery with high accuracy and reliability.

Estudo da influência de tratamentos químicos da fibra de sisal nas propriedades de compósitos com borracha nitrílica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Evaluation of curcumin and cisplatin-induced DNA damage in PC12 cells by the alkaline comet assay

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Diferença no tamanho de cascas de ovos de colônias de Panstrongylus megistus

O objetivo do estudo foi avaliar as mensurações de cascas de ovos de duas colônias laboratoriais e uma silvestre de P. megistus. de cada uma das colônias, 50 cascas de ovos foram mensuradas por meio de microscópio estereoscópico e sistema de análise de imagem QWin. A análise estatística foi efetuada utilizando o teste t-Student, não pareado no programa INSTAT. A largura, o comprimento e o diâmetro da abertura opercular das cascas de ovos de uma colônia silvestre foram maiores que de duas colônias laboratoriais de P. megistus.

Avaliação microscópica dos fragmentos ósseos obtidos por diferentes métodos de osteotomia e de irrigação em aloenxertos irradiados e congelados de coelho

Oral and facial bone defects can undertake appearance, psychosocial well-being and stomathognatic function of its patients. Over the yerars several strategies for bone defect regeneration have arised to treat these pathologies, among them the use of frozen and irradiated bone allograft. Manipulation of bone grafts it s not determined yet, and several osteotomy alternatives can be observed. The present work evaluated with a microscope the bone fragments obtained from different osteotomy methods and irrigation on rings and blocks allografts irradiated and frozen at 80° negative in a rabbit model. The study is experimental in vitro and it sample was an adult male New Zealand rabbit. The animal was sacrificed to obtain long bones, that were submitted to freezing at 80º negative and irradiated with Cobalt- 60. Then the long bones were sectioned into 24 bone pieces, divided into 4 groups: G1 (n=06) osteotomy was performed with bur No. 6 forming rings with 5 mm thickness with high-speed handpiece with manual irrigation; G2 (n=06) osteotomy was performed with bur No. 6 forming rings with 5 mm thick with surgical motor with a manual irrigation rotation 1500 rpm; GA (n=06), osteotomy with trephine using manual irrigation with saline; and GB (n=06), osteotomy with trephine using saline from peristaltic pumps of surgical motor. Five bone pieces of each group were prepared for analysis on light microscopy (LM) and one on electronic scan electronic microscopy (SEM). On the SEM analysis edges surface, presence of microcracks and Smear Layer were evaluated. Analyzing osteotomy technics on SEM was observed: increased presence of microcracks cutting with high speed; increased presence of areas covered by Smear Layer when cutting with motor implant. The irrigation analysis with SEM was observed: that the presence of microcracks does not depend on the type of irrigation; on manual irrigation, there was greater discrepancy between the cutting lines. The descriptive analysis of the osteotomy and irrigation process on LM showed: histological analysis showing the bony margins with clear tissue changed layer, composed of blackened tissue of charred appearance near to the cortical bone; on the edges of the bony part, bone fragments that were displaced during the bone cut and bone irregularities were observed. After analysis of results we can conclude: that there was greater regularity of the bone cut using high-speed handpiece than using motor implant; the cut with trephine using saline irrigated from peristaltic pumps of surgical motor showed greater homogeneity when compared with manual irrigation; charred tissue was found in all obtained bone samples, whit no significant statistically difference on the proportion of carbonization of the two analysed technics

Padrão de distribuição e caracterização morfológica de fibras serotonérgicas nos núcleos da linha Média/ intralaminares do tálamo do mocó (Kerodon rupestris)

The midline/intralaminar nuclei form a remarkable group of nuclei of the medial and dorsal thalamus. The midline nuclei, in rats, comprises the paratenial nuclei (PT), paraventricular (PV), intermediodorsal (IMD), reuniens (Re) and rhomboid (Rh). The intralaminar nuclei comprises the central medial (CM), paracentral (PC), central lateral (CL) and parafascicular (PF). Such nuclei have dense serotonergic innervation originating from the brainstem, especially from the so-called ascending activation system. These nuclei, in turn, send projections to various cortical and subcortical areas, specifically to limbic areas, which suggests the important role of this neurotransmitter in the limbic circuitry. The aim of this study was to characterize the distribution pattern and morphology of serotonin fibers in the nuclei of the midline and intralaminar thalamic of rocky cavy (Kerodon rupestris), a tipical rodent from brazilizan northeast. To reach this aim we used four rock cavies adults. Following the transcardially perfusion with paraformaldehyde and brain microtomy steps was performed immunohistochemistry for serotonin (5-HT), Nissl technique and subsequent achievement and image analysis to characterize the cytoarchitecture of these nuclei and the serotonergic fibers visualized. An analysis was made of Relative Optical Density (ROD) to semi-quantify the concentration of serotonin fibers in the areas of interest. Thus, we observed a cytoarchitectonic arrangement of these nuclei similar to that found in rats. In case of fibers distribution, those immunoreactive to 5-HT were presented in a higher concentration according as ROD in the midline nuclei relative to intralaminar; Re being the core which has a higher pixel value followed by the PV , Rh, IMD and PT. In intralaminar CL showed higher pixels, followed by nuclei CM, PC and PF. The serotonergic fibers were classified as number of varicosities and axon diameter, therefore find three types of fibers distributed through this nuclear complex: fibers rugous, granular and semi-granular. In PV fibers predominated rugous; in PT fibers predominated granular; IMD, CL and PF fibers were represented by semi-granular and Re, Rh, PC and CM fibers showed granular and semi-granular. Morphological characterization of serotonergic fibers and differences in density between the nuclei may suggest different patterns of synaptic organization of this neurotransmitter beyond confirming his large repertoire functional

Qualitative and quantitative characterization of aluminium alloys after corrosion testing

The 2024 and 7050 aluminium alloys used as aircraft components were subjected to laboratory corrosion tests in sodium chloride solution, Light-microscope examinations make it possible to characterise morphological aspects of the localised corrosion. Image analysis was used to determine both depth and width of pits over corroded surfaces. It has been concluded that the annealing could reduce the pit growth in both alloys, by means of grains recrystallization or recovery. The 2024 alloy also tends to present an exfoliation mechanism, mainly throughout non-recrystallized and recrystallized grain boundaries, increasing the width and sustaining the depth of pit cavities during exposition to saline atmosphere. SEM and EDS analysis reveal the morphology and elemental distribution of the corrosion products formed after immersion corrosion test. Some of these products were identified by X-ray diffraction analysis. For 2024, Al(OH)(3), MS(OH)(2) and Cu2O were found. AI(OH)(3) and Cu2O were also found in 7050 samples.