Acetaldehyde Production in the Direct Ethanol Fuel Cell: Mechanistic Elucidation by Density Functional Theory

This study employs density functional theory (DFT) calculations to examine the mechanism by which acetaldehyde is formed on platinum in a typical direct ethanol fuel cell (DEFC). A pathway is found involving the formation of a strongly hydrogen-bonded complex between adsorbed ethanol and the surface hydroxyl (OH) species, followed by the facile alpha-dehydrogenation of ethanol, with spontaneous weakening of the hydrogen bond in favor of adsorbed acetaldehyde and water. This mechanism is found to be comparably viable on both the close-packed surface and the monatomic steps. Comparison of further reactions on these two sites strongly indicates that the steps act as net removers of acetaldehyde from the product stream, while the flat surface acts as a net producer.

Ti mesh anodes prepared by electrochemical deposition for the direct methanol fuel cell

An anode structure based on Ti mesh has been developed for the direct methanol fuel cell (DMFC). This new anode was prepared by electrochemical deposition of a ~ 3 µ m PtRu catalyst layer on ~ 50 µ m Ti mesh. It has a thinner structure compared to that of a porous carbon-based conventional anode. The Ti mesh anode shows a performance comparable to, and exceeding that, of the conventional anode in a DMFC operating with 0.25 or 0.5 M methanol solution and atmosphere oxygen at 90 C. However, it shows a lower performance of the cell when higher concentrations of methanol was employed. This may be attributed to its thin and open structure, which could facilitate the transport of methanol from the flow field to the anode catalyst layer and carbon dioxide in the opposite direction. © 2006 International Association for Hydrogen Energy.

Inhibition of ribosome biogenesis induces apoptosis in p53-/- cells

The nucleolus is an important region of the nucleus that acts as the main site of rRNA transcription by RNA polymerase I (Pol-I), and one of the most prominent morphological markers of proliferative and invasive cancers is increased nucleolar size. Increases in Pol-I transcription leads to increased levels of ribosome biogenesis that are able to fuel rapid cell growth and proliferation due to increased ribosome numbers. Therefore Pol-I transcription seems a viable target for the development of anticancer therapeutics as abrogation of Pol-I transcription leads to cessation of cell growth and eventual cell death. We have confirmed that ellipticine compound, 9-Hydroxyellipticine (9HE), is an efficient inhibitor of Pol-I transcription in vitro and in p53+/+ and -/- cell lines in vivo. Short-term treatments (≤24 h) with micromolar concentrations of 9HE leads to decreased cell viability and proliferation, and leads to activation of caspases 3, 8 and 9, indicating that both intrinsic and extrinsic cell death mechanisms are activated upon Pol-I inhibition. Reactive oxygen species levels were also studied following short and long term treatments with 9HE and there was a 2/3-fold increase in cellular ROS levels. Long-term 9HE treatment (≥24 h) leads to cellular senescence as indicated by increased cellular morphology and senescence associated β-galactosidase staining, and this senescence is not accompanied by induction of autophagy. Following 24 h treatment there is also accumulation of cells in the G0/G1 phase of the cell cycle and qPCR analysis of cell cycle regulators shows down-regulation of G1/S transition associated cyclins. These data show that Pol-I transcription is a viable target for the development of novel chemotherapeutics, although further delineation of the cell death pathways remains. To further elucidate the mechanism, the role of mitochondrial death signals will be investigated by determination of cytochrome c release and regulation of Bcl2 family member proteins.

Exploring molecular recognition pathways within a family of gelators with different hydrogen bonding motifs

We report the synthesis of a family of gelators in which alkyl chains are connected to the amino groups of L-lysine methyl ester using a range of different hydrogen bonding linking groups (carbamate, amide, urea, thiourea and diacylhydrazine) using simple synthetic methodology based on isocyanate or acid chloride chemistry. The ability of these compounds to gelate organic solvents such as toluene or cyclohexane can be directly related to the ability of the linking group to form intermolecular hydrogen bonds. In general terms, the ability to structure solvents can be considered as: thiourea <carbamate <amide <urea similar to diacylhydrazine. This process has been confirmed by thermal measurements, scanning electron microscopy (SEM) and infrared and circular dichroism spectroscopies. By deprotecting the methyl ester group, we have demonstrated that a balance between hydrophobic and hydrophilic groups is essential-if the system has too much hydrophilicity (e. g., diacylhydrazine, urea) it will not form gels due to low solubility in the organic media. However, the less effective gelators based on amide and carbamate linkages are enhanced by converting the methyl ester to a carboxylic acid. Furthermore, subsequent mixing of the acid with a second component (diaminododecane) further enhances the ability to form networks, and, in the case of the amide, generates a two-component gel, which can immobilise a wide range of solvents of industrial interest including petrol and diesel (fuel oils), olive oil and sunflower oil (renewable food oils) and ethyl laurate, isopropyl myristate and isopropyl palmitate (oils used in pharmaceutical formulation). The gels are all thermoreversible, and may therefore be useful in controlled release/formulation applications.

Measurement of The Dynamic Response of Compressed Hydrogen by Inelastic X-Ray Scattering

Measurement of the dynamic properties of hydrogen and helium under extreme pressures is a key to understanding the physics of planetary interiors. The inelastic scattering signal from statically compressed hydrogen inside diamond anvil cells at 2.8 GPa and 6.4 GPa was measured at the Diamond Light Source synchrotron facility in the UK. The first direct measurement of the local field correction to the Coulomb interactions in degenerate plasmas was obtained from spectral shifts in the scattering data and compared to predictions by the Utsumi-Ichimaru theory for degenerate electron liquids.

Stable Isolated Metal Atoms as Active Sites for Photocatalytic Hydrogen Evolution

The process of using solar energy to split water to produce hydrogen assisted by an inorganic semiconductor is crucial for solving our energy crisis and environmental problems in the future. However, most semiconductor photocatalysts would not exhibit excellent photocatalytic activity without loading suitable co-catalysts. Generally, the noble metals have been widely applied as co-catalysts, but always agglomerate during the loading process or photocatalytic reaction. Therefore, the utilization efficiency of the noble co-catalysts is still very low on a per metal atom basis if no obvious size effect exists, because heterogeneous catalytic reactions occur on the surface active atoms. Here, for the first time, we have synthesized isolated metal atoms (Pt, Pd, Rh, or Ru) stably by anchoring on TiO2, a model photocatalystic system, by a facile one-step method. The isolated metal atom based photocatalysts show excellent stability for H-2 evolution and can lead to a 6-13-fold increase in photocatalytic activity over the metal clusters loaded on TiO2 by the traditional method. Furthermore, the configurations of isolated atoms as well as the originality of their unusual stability were analyzed by a collaborative work from both experiments and theoretical calculations.

The application of a novel fluidised photo reactor under UV-Visible and natural solar irradiation in the photocatalytic generation of hydrogen

With advancements in the development of visible light responsive catalysts for H2 production frequently being reported, photocatalytic water splitting has become an attractive method as a potential ‘solar fuel generator’. The development of novel photo reactors which can enhance the potential of such catalyst, however, is rarely reported. This is particularly important as many reactor configurations are mass transport limited, which in term limits the efficiency of more effective photocatalysts in larger scale applications. This paper describes the performance of a novel fluidised photo reactor for the production of H2 over two catalysts under UV-Visible light and natural solar illumination. Catalysts Pt-C3N4 and NaTaO3.La were dispersed in the reactor and the rate of H2 was determined by GC-TCD analysis of the gas headspace. The unit was an annular reactor constructed from stainless steel 316 and quartz glass with a propeller located in the base to control fluidisation of powder catalysts. Reactor properties such as propeller rotational speed were found to enhance the photo activity of the system through the elimination of mass transport limitations and increasing light penetration. The optimum conditions for H2 evolution were found to be a propeller rotational speed of 1035 rpm and 144 W of UV-Visible irradiation, which produced a rate of 89 µmol h-1 g-1 over Pt-C3N4. Solar irradiation was provided by the George Ellery Hale Solar Telescope, located at the California Institute of Technology.

Extension of electrochemically active sites in SOFCs and SOECs

Solid oxide fuel (SOFCs) and electrolyzer (SOECs) cells have been promoted as promising technologies for the stabilization of fuel supply and usage in future green energy systems. SOFCs are devices that produce electricity by the oxidation of hydrogen or hydrocarbon fuels with high efficiency. Conversely, SOECs can offer the reverse reaction, where synthetic fuels can be generated by the input of renewable electricity. Due to this similar but inverse nature of SOFCs and SOECs, these devices have traditionally been constructed from comparable materials. Nonetheless, several limitations have hindered the entry of SOFCs and SOECs into the marketplace. One of the most debilitating is associated with chemical interreactions between cell components that can lead to poor longevities at high working temperatures and/or depleted electrochemcial performance. Normally such interreactions are countered by the introduction of thin, purely ionic conducting, buffer layers between the electrode and electrolyte interface. The objective of this thesis is to assess if possible improvements in electrode kinetics can also be obtained by modifying the transport properties of these buffer layers by the introduction of multivalent cations. The introduction of minor electronic conductivity in the surface of the electrolyte material has previously been shown to radically enhance the electrochemically active area for oxygen exchange, reducing polarization resistance losses. Hence, the current thesis aims to extend this knowledge to tailor a bi-functional buffer layer that can prevent chemical interreaction while also enhancing electrode kinetics.The thesis selects a typical scenario of an yttria stabilized zirconia electrolyte combined with a lanthanide containing oxygen electrode. Gadolinium, terbium and praseodymium doped cerium oxide materials have been investigated as potential buffer layers. The mixed ionic electronic conducting (MIEC) properties of the doped-cerium materials have been analyzed and collated. A detailed analysis is further presented of the impact of the buffer layers on the kinetics of the oxygen electrode in SOFC and SOEC devices. Special focus is made to assess for potential links between the transport properties of the buffer layer and subsequent electrode performance. The work also evaluates the electrochemical performance of different K2NiF4 structure cathodes deposited onto a peak performing Pr doped-cerium buffer layer, the influence of buffer layer thickness and the Pr content of the ceria buffer layer. It is shown that dramatic increases in electrode performance can be obtained by the introduction of MIEC buffer layers, where the best performances are shown to be offered by buffer layers of highest ambipolar conductivity. These buffer layers are also shown to continue to offer the bifunctional role to protect from unwanted chemical interactions at the electrode/electrolyte interface.

How hydrogen peroxide and CXCL8 modulate neutrophil recruitment "in vivo"

Tese de doutoramento, Ciências Biomédicas (Biologia Celular e Molecular), Universidade de Lisboa, Faculdade de Medicina, 2014

Hydrogen peroxide sensing, signaling and regulation of transcription factors

The regulatory mechanisms by which hydrogen peroxide (H2O2) modulates the activity of transcription factors in bacteria (OxyR and PerR), lower eukaryotes (Yap1, Maf1, Hsf1 and Msn2/4) and mammalian cells (AP-1, NRF2, CREB, HSF1, HIF-1, TP53, NF-κB, NOTCH, SP1 and SCREB-1) are reviewed. The complexity of regulatory networks increases throughout the phylogenetic tree, reaching a high level of complexity in mammalians. Multiple H2O2 sensors and pathways are triggered converging in the regulation of transcription factors at several levels: (1) synthesis of the transcription factor by upregulating transcription or increasing both mRNA stability and translation; (ii) stability of the transcription factor by decreasing its association with the ubiquitin E3 ligase complex or by inhibiting this complex; (iii) cytoplasm-nuclear traffic by exposing/masking nuclear localization signals, or by releasing the transcription factor from partners or from membrane anchors; and, (iv) DNA binding and nuclear transactivation by modulating transcription factor affinity towards DNA, co-activators or repressors, and by targeting specific regions of chromatin to activate individual genes. We also discuss how H2O2 biological specificity results from diverse thiol protein sensors, with different reactivity of their sulfhydryl groups towards H2O2, being activated by different concentrations and times of exposure to H2O2. The specific regulation of local H2O2 concentrations is also crucial and results from H2O2 localized production and removal controlled by signals. Finally, we formulate equations to extract from typical experiments quantitative data concerning H2O2 reactivity with sensor molecules. Rate constants of 140 M-1s−1 and ≥ 1.3 × 103 M-1s−1 were estimated, respectively, for the reaction of H2O2 with KEAP1 and with an unknown target that mediates NRF2 protein synthesis. In conclusion, the multitude of H2O2 targets and mechanisms provides an opportunity for highly specific effects on gene regulation that depend on the cell type and on signals received from the cellular microenvironment.

Factors affecting DNA uptake by mammalian cells

The ability to introduce DNA and express custom DNA sequences in bacteria opened the door for improvements in a large number of fields including agriculture, pharmacology, medicine, nutrition, etc. The ability to introduce foreign DNA sequences into mammalian cells in an efficient manner would have a large impact on therapeutic applications especially gene therapy. The methods in use today suffer from low efficiencies and sometimes toxicity. In this work a number of factors were evaluated for their effect onONA uptake efficiency. The factors studied included exposure to sublethal concentration of hydrogen peroxide which have been show to lead to destabilisation ofthe lysosomes. These exposures have proven to be very toxic to cells when combined with either the calcium phosphate or the lipofectAMINE® transfection methods. Another factor evaluated was exposure to Electro-Magnetic Fields (EMF). This was fuelled by the fact that EMF have been shown to mediate a number of effects on cell structure and/or physiology. EMF exposure by itself was not sufficient to induce the cells to pick up the DNA, therefore its effect on calcium phosphate and lipofectAMINE® was tested. Although some positive results were obtained, the variability of these results exceeded by far any observed enhancements which discouraged any further work on EMF. Also tested was the possible effect the presence of the cytomegalovirus (CMV) sequence might have on DNA uptake (based on previous results in this lab). It was found that the presence ofCMV in the DNA sequence does not enhance uptake or slow down degradation of the internalised DNA. The final factor tested was the effect of basic amino acids on transfection efficiency. It was found that arginine can enhance DNA uptake by about 170% v/ith calcium phosphate and about 200% with LipofectAMINE®. A model was proposed to explain the effect of arginine as well as the lack of effect from other amino acids.

Endothelin-1 and H2O2-induced signaling in vascular smooth muscle cells : modulation by CaMKII and Nitric oxide

L’endothéline-1 (ET-1) est un peptide vasoactif extrêmement puissant qui possède une forte activité mitogénique dans les cellules du muscle lisse vasculaire (VSMCs). Il a été démontré que l’ET-1 est impliquée dans plusieurs maladies cardio-vasculaires, comme l’athérosclérose, l'hypertension, la resténose après l'angioplastie, l’insuffisance cardiaque et l'arythmie. L’ET-1 exerce ses effets via plusieurs voies de signalisation qui incluent le Ca2+, les protéines kinases activées par les mitogènes (MAPKs) y compris les kinases régulées par les signaux extracellulaires (ERK1/2) et la voie de la phosphatidylinositol 3-kinase (PI-3K)/protein kinase B (PKB). Plusieurs études ont démontré que les dérivés réactifs de l'oxygène (ROS) peuvent jouer un rôle important dans la signalisation d’ERK1/2 et de PKB induite par plusieurs facteurs de croissance et hormones. Nous avons précédemment montré que l'ET-1 produit des ROS qui agissent comme médiateur de la signalisation cellulaire induite par l’ET-1. Le peroxyde d’hydrogène (H2O2), une molécule qui appartient à la famille des ROS, peut activer les voies de la MAPK et de la PKB dans les VSMCs. Par ailleurs, nos résultats suggèrent également que le Ca2+ et la calmoduline (CaM) sont essentiels pour la phosphorylation d’ERK1/2, de p38 et de PKB induite par le H2O2 dans les VSMCs. La Ca2+/CaM-dependent protein kinases II (CaMKII) est une sérine/thréonine protéine kinase multifonctionnelle activée par le Ca2+/CaM. Il a été montré que la CaMKII est impliquée dans les voies de signalisation induite par le H2O2 dans les cellules endothéliales. Cependant, le rôle de la CaMKII dans la phosphorylation d’ERK1/2, de PKB et de la proline-rich tyrosine kinase 2 (Pyk2) induite par l’ET-1 et le H2O2, de même que son rôle dans l’effet hypertrophique et prolifératif de l’ET-1 dans les VSMCs demeure inexploré. Le monoxyde d’azote (NO) est une molécule vasoactive impliquée dans la régulation de plusieurs réponses hormonales. Le NO peut moduler la signalisation contrôlant la croissance cellulaire induite par plusieurs agonistes d’où son rôle protecteur dans le système vasculaire. Des études ont montré que le NO peut inhiber la voie de Ras/Raf/ERK1/2 et la voie de PKB induite par le facteur de croissance endothélial (EGF) et l’angiotensine II (Ang II). Beaucoup d’autres travaux ont mis en évidence un cross-talk entre les voies de signalisation activées par l’ET-1 et le NO. La capacité du NO à inhiber la signalisation intracellulaire induite par l’ET-1 dans les VSMCs demeure inconnue. Le travail présenté dans cette thèse vise à déterminer le rôle du système Ca2+-CaM-CaMKII dans la phosphorylation d’ERK1/2, de PKB et de Pyk2 induite par l’ET-1 et le H2O2 ainsi que son rôle dans la croissance et la prolifération cellulaire induites par l’ET-1 dans les VSMCs. Nous avons également testé le rôle du NO dans la phosphorylation d’ERK1/2, de PKB et de Pyk2 ainsi que la synthèse protéique induite par l’ET-1. Dans la première partie de notre étude, nous avons examiné le rôle de la CaMKII dans la phosphorylation d’ERK1/2 et de PKB induite par l’ET-1 dans les VSMCs en utilisant trois approches différentes i.e. l'usage d'inhibiteurs pharmacologiques, un peptide auto-inhibiteur de la CaMKII (CaMKII AIP) et la technique de siRNA. Nous avons démontré que la CaMKII est impliquée dans la phosphorylation d’ERK1/2 et de PKB induite par l’ET-1 dans les VSMCs. Des études précédentes ont montré à l’aide d’inhibiteurs pharmacologiques comme le KN-93 que l'Ang II et les agents induisant une augmentation de la concentration en Ca2+ intracellulaire comme l’ionomycine, provoquent la phosphorylation d’ERK1/2 via la CaM dans les VSMCs. Cependant, en utilisant différentes approches, nos études ont montré pour la première fois une implication de la CaMKII dans la phosphorylation d’ERK1/2 et de PKB induite par l’ET-1 dans les VSMCs. Nous avons également rapporté pour la première fois, un rôle crucial de la CaMKII dans la pathophysiologie vasculaire associée à l’ET-1 puisque l’activation de la CaMKII joue un rôle important dans l’hypertrophie et la croissance cellulaire. Dans la deuxième partie, à la lumière des études précédentes qui montraient que les ROS agissent comme médiateurs de la signalisation induite par l’ET-1 dans les VSMCs, nous avons examiné si la CaMKII est également impliquée dans l’activation des voies d’ERK1/2 et de PKB induite par le H2O2. En utilisant des approches pharmacologiques et moléculaires, nous avons montré, comme pour l’ET-1, que la CaMKII joue un rôle critique en amont de la phosphorylation d’ERK1/2, de PKB et de Pyk2 induite par le H2O2. Nous avons précédemment montré que la transactivation du récepteur de type I de l’insulin-like growth factor (IGF-1R) est nécessaire à l’activation de PKB induite par le H2O2. Pour cette raison, nous avons examiné l'effet de l'inhibition de la CaMKII par l’inhibiteur pharmacologique ou par le knock-down de la CaMKII sur la phosphorylation d’IGF-1R induite par le H2O2. Les résultats démontrent que la CaMKII joue un rôle critique en amont de la phosphorylation d’ERK1/2, de PKB et d’IGF-1R induite par le H2O2. Dans la troisième partie de notre étude, nous avons également examiné le mécanisme moléculaire par lequel le NO exerce ses effets anti-mitogéniques et anti-hypertrophiques dans la signalisation induite par l’ET-1. En testant l'effet de deux différents donneurs de NO (S-nitroso-N-acetylpenicillamine (SNAP), sodium nitroprusside (SNP)) et un inhibiteur de NO synthase, le N (G)-nitro-L-arginine methyl ester (L-NAME) dans la phosphorylation d’ERK1/2, de PKB et de Pyk2 induite par l’ET-1, nous avons observé que le NO a un effet inhibiteur sur la signalisation induite par l’ET-1 dans les VSMCs. Par ailleurs, le 8-Br-GMPc, un analogue du GMPc, a un effet similaire à celui des deux donneurs du NO, tandis que l’oxadiazole quinoxaline (ODQ), un inhibiteur de la guanylate cyclase soluble, inverse l'effet inhibiteur du NO. Nous concluons que le NO diminue la phosphorylation d’ERK1/2, de PKB et de Pyk2 induite par l’ET-1 d’une manière dépendante du GMPc. Le NO inhibe aussi les effets hypertrophiques de l’ET-1 puisque le traitement avec le SNAP diminue la synthèse des protéines induite par l’ET-1. En résumé, les études présentées dans cette thèse démontrent que l’ET-1 et le H2O2 sont des activateurs de la phosphorylation d’ERK1/2, de PKB et de Pyk2 dans les VSMCs et que la CaMKII s’avère nécessaire pour ce processus, en agissant en amont de l’activation de IGF-1R induite par le H2O2 dans les VSMCs. Elles montrent également que le NO inhibe la phosphorylation d’ERK1/2, de PKB et de Pyk2 induite par l’ET-1. Enfin, nos travaux suggèrent aussi que l’activation de la CaMKII stimule la synthèse des protéines et de l’ADN induites par l’ET-1 alors que le NO inhibe la synthèse des protéines induite par ET-1. Mots clés: Endothéline ; Peroxyde d'hydrogène ; CaMKII ; Monoxyde d’azote ; Système vasculaire ; PKB; ERK1/2; IGF-1R; Hypertrophie.

Modelling and simulation of a photovoltaic fuel cell hybrid system

A stand-alone power system is an autonomous system that supplies electricity to the user load without being connected to the electric grid. This kind of decentralized system is frequently located in remote and inaccessible areas. It is essential for about one third of the world population which are living in developed or isolated regions and have no access to an electricity utility grid. The most people live in remote and rural areas, with low population density, lacking even the basic infrastructure. The utility grid extension to these locations is not a cost effective option and sometimes technically not feasible. The purpose of this thesis is the modelling and simulation of a stand-alone hybrid power system, referred to as “hydrogen Photovoltaic-Fuel Cell (PVFC) hybrid system”. It couples a photovoltaic generator (PV), an alkaline water electrolyser, a storage gas tank, a proton exchange membrane fuel cell (PEMFC), and power conditioning units (PCU) to give different system topologies. The system is intended to be an environmentally friendly solution since it tries maximising the use of a renewable energy source. Electricity is produced by a PV generator to meet the requirements of a user load. Whenever there is enough solar radiation, the user load can be powered totally by the PV electricity. During periods of low solar radiation, auxiliary electricity is required. An alkaline high pressure water electrolyser is powered by the excess energy from the PV generator to produce hydrogen and oxygen at a pressure of maximum 30bar. Gases are stored without compression for short- (hourly or daily) and long- (seasonal) term. A proton exchange membrane (PEM) fuel cell is used to keep the system’s reliability at the same level as for the conventional system while decreasing the environmental impact of the whole system. The PEM fuel cell consumes gases which are produced by an electrolyser to meet the user load demand when the PV generator energy is deficient, so that it works as an auxiliary generator. Power conditioning units are appropriate for the conversion and dispatch the energy between the components of the system. No batteries are used in this system since they represent the weakest when used in PV systems due to their need for sophisticated control and their short lifetime. The model library, ISET Alternative Power Library (ISET-APL), is designed by the Institute of Solar Energy supply Technology (ISET) and used for the simulation of the hybrid system. The physical, analytical and/or empirical equations of each component are programmed and implemented separately in this library for the simulation software program Simplorer by C++ language. The model parameters are derived from manufacturer’s performance data sheets or measurements obtained from literature. The identification and validation of the major hydrogen PVFC hybrid system component models are evaluated according to the measured data of the components, from the manufacturer’s data sheet or from actual system operation. Then, the overall system is simulated, at intervals of one hour each, by using solar radiation as the primary energy input and hydrogen as energy storage for one year operation. A comparison between different topologies, such as DC or AC coupled systems, is carried out on the basis of energy point of view at two locations with different geographical latitudes, in Kassel/Germany (Europe) and in Cairo/Egypt (North Africa). The main conclusion in this work is that the simulation method of the system study under different conditions could successfully be used to give good visualization and comparison between those topologies for the overall performance of the system. The operational performance of the system is not only depending on component efficiency but also on system design and consumption behaviour. The worst case of this system is the low efficiency of the storage subsystem made of the electrolyser, the gas storage tank, and the fuel cell as it is around 25-34% at Cairo and 29-37% at Kassel. Therefore, the research for this system should be concentrated in the subsystem components development especially the fuel cell.

Involvement of phenazine-1-carboxylic acid, siderophores and hydrogen cyanide in suppression of Rhizoetonia solani and Pythium spp. damping-off by Pseudomonas oryzihabitans and Xenorhabdus nematophila

Entomopathogenic bacterial strains Pseudomonas (Flavimonas) oryzihabitans and Xenorhabdus nematophilus, both bacterial symbionts of the entomopathogenic nematodes Steinernema abbasi and S. carpocapsae have been recently used for suppression of soil-borne pathogens. Bacterial biocontrol agents (P. oryzihabitans and X nematophila) have been tested for production of secondary metabolites in vitro and their fungistatic effect,on mycelium and spore development of soil-borne pathogens. Isolates of Pythium spp. and Rhizoctonia solani, the causal agent of cotton damping-off, varied in sensitivity in vitro to the antibiotics phenazine-I-carboxylic acid (PCA), cyanide (HCN) and siderophores produced by bacterial strains shown previously to have potential for biological control of those pathogens. These findings affirm the role of the antibiotics PCA, HCN and siderophores in the biocontrol activity of these entomopathogenic strains and support earlier evidence that mechanisms of secondary metabolites are responsible for suppression of damping-off diseases. In the present studies colonies of R oryzihabitans showed production of PCA with presence of crystalline deposits after six days development and positive production where found as well in the siderophore's assay when X nematophila strain indicated HCN production in the in vitro assays. In vitro antifungal activity showed that bacteria densities of 101 to 10(6)cells/ml have antifungal activity in different media cultures. The results show further that isolates of Pythium spp. and R. solani insensitive to PCA, HCN and siderophores are present in the pathogen population and provide additional justification for the use of mixtures of entomopathogenic strains that employ different mechanisms of pathogen suppression to manage damping-off.

Tin and tin-titanium as catalyst components for reversible hydrogen storage of sodium aluminium hydride

This paper is concerned with the effects of adding tin and/or titanium dopant to sodium aluminium hydride for both dehydrogenation and re-hydrogenation reactions during their reversible storage of molecular hydrogen. Temperature programmed decomposition (TPD) measurements show that the dehydrogenation kinetics of NaAlH4 are significantly enhanced upon doping the material with 2 mol% of tributyltin hydride, Sn(Bu)(3)H but the tin catalyst dopant is shown to be inferior than titanium. On the other hand, in this preliminary work, a significant synergetic catalytic effect is clearly revealed in material co-doped with both titanium and tin catalysts which shows the highest reversible rates of dehydrogenation and re-hydrogenation (after their hydrogen depletion). The re-hydrogenation rates of depleted Sn/Ti/NaAlH4 evaluated at both 9.5 and 140 bars hydrogen are also found to be favourable compared to the Ti/NaAlH4, which clearly suggest the importance of the catalyst choice. Basing on these results some mechanistic insights for the catalytic reversible dehydrogenation and re-hydrogenation processes of Sn/Ti/NaAlH4 are therefore made. (C) 2006 Elsevier Ltd. All rights reserved.