Scale Effects in Hydraulic Model Tests of Rock Protected Structures, HR-119, 1970

A laboratory investigation was undertaken to determine the limiting model Reynolds number above which the scour behavior of rock protected structures can be reproduced in hydraulic models scaled according to the Froude criterion. A submerged jet was passed over an initially full scour pocket containing uniform glass spheres and the rate of scour was measured as a function of time. The dimensions of the scour pocket and jet and the particle diameters were varied as needed to maintain strict geometric similarity. For each of two different Froude numbers the Reynolds number was varied over a wide range. The normalized scour rate was found to be practically independent of the Reynolds number, R, (based on the jet velocity and particle diameter) at values of R above about 2.5 x 10^3, and to decrease with Rat smaller values. A grid placed in the jet was found to have a very strong effect on the scour rate. In an attempt to explain the effect of R on the scour behavior, turbulent pressure and velocity fluctuations were measured in air flows and water flows, respectively, over rigid scour pockets having the same geometry as those formed in the scour experiments. The normalized spectra of the fluctuations were found to be nearly independent of R, but the flow pattern was found to be very sensitive to the inlet condition, the jet deflecting upward or downward in a not wholly explainable manner. This indicates that scour behavior can be modeled only if the approach flow is also accurately modeled.

Exhaled breath condensate as a matrix for combustion-based nanoparticle exposure and health effect evaluation

Health assessment and medical surveillance of workers exposed to combustion nanoparticles are challenging. The aim was to evaluate the feasibility of using exhaled breath condensate (EBC) from healthy volunteers for (1) assessing the lung deposited dose of combustion nanoparticles and (2) determining the resulting oxidative stress by measuring hydrogen peroxide (H2O2) and malondialdehyde (MDA). Methods: Fifteen healthy nonsmoker volunteers were exposed to three different levels of sidestream cigarette smoke under controlled conditions. EBC was repeatedly collected before, during, and 1 and 2 hr after exposure. Exposure variables were measured by direct reading instruments and by active sampling. The different EBC samples were analyzed for particle number concentration (light-scattering-based method) and for selected compounds considered oxidative stress markers. Results: Subjects were exposed to an average airborne concentration up to 4.3×10(5) particles/cm(3) (average geometric size ∼60-80 nm). Up to 10×10(8) particles/mL could be measured in the collected EBC with a broad size distribution (50(th) percentile ∼160 nm), but these biological concentrations were not related to the exposure level of cigarette smoke particles. Although H2O2 and MDA concentrations in EBC increased during exposure, only H2O2 showed a transient normalization 1 hr after exposure and increased afterward. In contrast, MDA levels stayed elevated during the 2 hr post exposure. Conclusions: The use of diffusion light scattering for particle counting proved to be sufficiently sensitive to detect objects in EBC, but lacked the specificity for carbonaceous tobacco smoke particles. Our results suggest two phases of oxidation markers in EBC: first, the initial deposition of particles and gases in the lung lining liquid, and later the start of oxidative stress with associated cell membrane damage. Future studies should extend the follow-up time and should remove gases or particles from the air to allow differentiation between the different sources of H2O2 and MDA.

Evidence for morphological and adaptive genetic divergence between lake and stream habitats in European minnows (Phoxinus phoxinus, Cyprinidae).

Natural selection drives local adaptation, potentially even at small temporal and spatial scales. As a result, adaptive genetic and phenotypic divergence can occur among populations living in different habitats. We investigated patterns of differentiation between contrasting lake and stream habitats in the cyprinid fish European minnow (Phoxinus phoxinus) at both the morphological and genomic levels using geometric morphometrics and AFLP markers, respectively. We also used a spatial correlative approach to identify AFLP loci associated with environmental variables representing potential selective forces responsible for adaptation to divergent habitats. Our results identified different morphologies between lakes and streams, with lake fish presenting a deeper body and caudal peduncle compared to stream fish. Body shape variation conformed to a priori predictions concerning biomechanics and swimming performance in lakes vs. streams. Moreover, morphological differentiation was found to be associated with several environmental variables, which could impose selection on body and caudal peduncle shape. We found adaptive genetic divergence between these contrasting habitats in the form of 'outlier' loci (2.9%) whose genetic divergence exceeded neutral expectations. We also detected additional loci (6.6%) not associated with habitat type (lake vs. stream), but contributing to genetic divergence between populations. Specific environmental variables related to trophic dynamics, landscape topography and geography were associated with several neutral and outlier loci. These results provide new insights into the morphological divergence and genetic basis of adaptation to differentiated habitats.

Prolonged fluconazole exposure leads to a shift to Candida species with decreased susceptibility in breakthrough candidemia: prospective survey of the Fungal Infection Network of Switzerland

Objectives: To compare the clinical characteristics, species distribution and antifungal susceptibility of Candida bloodstream isolates (BSI) in breakthrough (BTC) vs. non-breakthrough candidemia (NBTC) and to study the effect of prolonged vs. short fluconazole (F) exposure in BTC.Methods: Candida BSI were prospectively collected during 2004- 2006 from 27 hospitals (seven university, 20 affiliated) of the FUNGINOS network. Susceptibility to F, voriconazole (V) and caspofungin (C) was tested in the FUNGINOS mycology reference laboratory by microtitre broth dilution method with the Sensititre YeastOneTM test panel. Clinical data were collected using standardized CRFs. BTC was defined as occurring during antifungal treatment/prophylaxis of at least three days duration prior to the candidemia. Susceptibility of BSI was defined according to 2010/2011 CLSI clinical breakpoints.Results: Out of 567 candidemia episodes, 550 Candida BSI were available. Of these, 43 (7.6%) were from BTC (37/43, 86% were isolated after F exposure). 38 BTC (88.4%) and 315 NBTC (55.6%) occurred in university hospitals (P < 0.001). The majority of patients developing BTC were immunocompromised: higher proportions of haematological malignancies (62.8% in BTC vs. 47.1% in NBTC, P < 0.001), neutropenia (37.2% vs. 11.8%, P < 0.001), acute GvHD (14% vs. 0.2%, P < 0.001), immunosuppressive drugs (74.4% vs. 7.8%, P < 0.001), and mucositis (32.6% vs. 2.3%, P < 0.001) were observed. Other differences between BTC and NBTC were higher proportions of patients with central venous catheters in the 2 weeks preceding candidemia (95.3% vs. 83.4%, P = 0.047) and receiving total parenteral nutrition (62.8% vs. 35.9%, P < 0.001), but a lower proportion of patients treated with gastric proton pump inhibitors (23.3% vs. 72.1%, P < 0.001). Overall mortality of BTC and NBTC was not different (34.9% vs. 31.7%, P = 0.73), while a trend to higher attributable mortality in BTC was found (13.9% vs. 6.9%, P = 0.12). Species identification showed a majority of C. albicans in both groups (51.2% in BTC vs. 62.9% in NBTC, P = 0.26), followed by C. glabrata (18.6% vs. 18.5%), C. tropicalis (2.3% vs. 6.3%) and C. parapsilosis (7.0% vs. 4.7%). Significantly more C. krusei were detected in BTC versus NBTC (11.6% vs. 1.6%, P = 0.002). The geometric mean MIC for F, V and C between BTC and NBTC isolates was not significantly different. However, in BTC there was a significant association between duration of F exposure and the Candida spp.: >10 days of F was associated with a significant shift from susceptible Candida spp. (C. albicans, C. parapsilosis, C. tropicalis, C. famata) to non-susceptible species (C. glabrata, C. krusei, C. norvegensis). Among 21 BTC episodes occurring after £10 days of F, 19% of the isolates were non-susceptible, in contrast to 68.7% in 16 BTC episodes occurring after >10 days of F (P = 0.003).Conclusions: Breakthrough candidemia occurred more often in immunocompromised hosts. Fluconazole administered for >10 days was associated with a shift to non-susceptible Candida spp.. Length of fluconazole exposure should be taken into consideration for the choice of empirical antifungal treatment.

Remote Sensing (LIDAR) for Management of Highway Assets for Safety, 2003

The main objective of this study was to utilize light detection and ranging (LIDAR) technology to obtain highway safety-related information. The safety needs of older drivers in terms of prolonged reaction times were taken into consideration. The tasks undertaken in this study were (1) identification of crashes that older drivers are more likely to be involved in, (2) identification of highway geometric features that are important in such crashes, (3) utilization of LIDAR data for obtaining information on the identified highway geometric features, and (4) assessment of the feasibility of using LIDAR data for such applications. A review of previous research indicated that older drivers have difficulty negotiating intersections, and it was recognized that intersection sight triangles were critical to safe intersection negotiation. LIDAR data were utilized to obtain information on potential sight distance obstructions at six selected intersections located on the Iowa Highway 1 corridor by conducting in-office line-of-sight analysis. Crash frequency, older driver involvement, and data availability were considerations in the selection of the six intersections. Results of the in-office analysis were then validated by visiting the intersections in the field. Sixty-six potential sight distance obstructions were identified by the line-of-sight analysis, out of which 62 (89.8%) were confirmed while four (5.8%) were not confirmed by the video. At least three (4.4%) potential sight distance obstructions were discovered in the video that were not detected by the line-of-sight analysis. The intersection with the highest crash frequency involving older drivers was correctly found to have obstructions located within the intersection sight triangles. Based on research results, it is concluded that LIDAR data can be utilized for identifying potential sight distance obstructions at intersections. The safety of older drivers can be enhanced by locating and rectifying intersections with obstructions in sight triangles.

Effectiveness of Roadway Safety Improvements, 2001

The Iowa Department of Transportation (DOT) continuously assesses the likely causes of crashes at high-crash locations throughout the Iowa roadway network and designs solutions to reduce the incidences of crashes. This research analyzed approximately 100 safety projects constructed in the past 10 years to see what affect they had on highway safety. The projects are grouped into seven categories as defined by their scope of work: (1) install new traffic signal, (2) add turn lane(s), (3) install new signal and turn lane(s), (4) add left-turn phasing, (5) add left-turn phasing and turn lane(s), (6) replace pedestal mount signals with mast arm signals, and (7) other geometric improvements. The project makes use of an extensive statewide crash database. The results of the project will evaluate the assumed reduction factors and benefit/cost (B/C) analysis, determine the actual cost effectiveness of the Iowa DOT's safety programs, and allow the Iowa DOT to better prioritize future improvements.

Field capture of Thyanta perditor with pheromone-baited traps

The objective of this work was to evaluate the field attractiveness of Thyanta perditor synthetic sex pheromone-baited traps, its attractivity to other stink bug species, and the response of T. perditor to a geometric isomer of the sex pheromone. Two-liter transparent plastic bottles traps were baited with rubber septa impregnated with the treatments: 1 mg of methyl-(2E,4Z,6Z)-decatrienoate [(2E,4Z,6Z)-10:COOMe], the male sex pheromone of T. perditor; 1 mg of (2E,4Z,6Z)-10:COOMe protected from sunlight in standard PVC plumbing pipe; 1 mg of its geometric isomer [(2E,4E,6Z)-10:COOMe]; and traps with rubber septa impregnated with hexane (control). The experiment was carried out in field during the soybean reproductive stages. Traps were monitored weekly, and the captures were compared to the population density estimated by the sampling cloth and visual inspection monitoring techniques. Traps baited with the sex pheromone, protected or not, were more effective in capturing T. perditor than traps baited with the isomer or the hexane. Thyanta perditor sex pheromone showed cross-attraction to other stink bug species, such as Euschistus heros, Edessa meditabunda, Piezodorus guildinii and Nezara viridula. Pheromone-baited traps can be used in population monitoring and to identify the relative composition of stink bug guilds.

Early Iron Age Pottery: A Quantitative Approach. Proceedings of the International Round Table organized by the Swiss School of Archaeology in Greece (Athens, Novembre 28-30, 2008).

Quantitative approaches in ceramology are gaining ground in excavation reports, archaeological publications and thematic studies. Hence, a wide variety of methods are being used depending on the researchers' theoretical premise, the type of material which is examined, the context of discovery and the questions that are addressed. The round table that took place in Athens on November 2008 was intended to offer the participants the opportunity to present a selection of case studies on the basis of which methodological approaches were discussed. The aim was to define a set of guidelines for quantification that would prove to be of use to all researchers. Contents: 1) Introduction (Samuel Verdan); 2) Isthmia and beyond. How can quantification help the analysis of EIA sanctuary deposits? (Catherine Morgan); 3) Approaching aspects of cult practice and ethnicity in Early Iron Age Ephesos using quantitative analysis of a Protogeometric deposit from the Artemision (Michael Kerschner); 4) Development of a ceramic cultic assemblage: Analyzing pottery from Late Helladic IIIC through Late Geometric Kalapodi (Ivonne Kaiser, Laura-Concetta Rizzotto, Sara Strack); 5) 'Erfahrungsbericht' of application of different quantitative methods at Kalapodi (Sara Strack); 6) The Early Iron Age sanctuary at Olympia: counting sherds from the Pelopion excavations (1987-1996) (Birgitta Eder); 7) L'aire du pilier des Rhodiens à Delphes: Essai de quantification du mobilier (Jean-Marc Luce); 8) A new approach in ceramic statistical analyses: Pit 13 on Xeropolis at Lefkandi (David A. Mitchell, Irene S. Lemos); 9) Households and workshops at Early Iron Age Oropos: A quantitative approach of the fine, wheel-made pottery (Vicky Vlachou); 10) Counting sherds at Sindos: Pottery consumption and construction of identities in the Iron Age (Stefanos Gimatzidis); 11) Analyse quantitative du mobilier céramique des fouilles de Xombourgo à Ténos et le cas des supports de caisson (Jean-Sébastien Gros); 12) Defining a typology of pottery from Gortyn: The material from a pottery workshop pit, (Emanuela Santaniello); 13) Quantification of ceramics from Early Iron Age tombs (Antonis Kotsonas); 14) Quantitative analysis of the pottery from the Early Iron Age necropolis of Tsikalario on Naxos (Xenia Charalambidou); 15) Finding the Early Iron Age in field survey: Two case studies from Boeotia and Magnesia (Vladimir Stissi); 16) Pottery quantification: Some guidelines (Samuel Verdan).

Deep incision in an Aptian carbonate succession indicates major sea-level fall in the Cretaceous

Long-term relative sea-level cycles (0 5 to 6 Myr) have yet to be fully understood for the Cretaceous. During the Aptian, in the northern Maestrat Basin (Eastern Iberian Peninsula), fault-controlled subsidence created depositional space, but eustasy governed changes in depositional trends. Relative sea-level history was reconstructed by sequence stratigraphic analysis. Two forced regressive stages of relative sea-level were recognized within three depositional sequences. The first stage is late Early Aptian age (intra Dufrenoyia furcata Zone) and is characterized by foreshore to upper shoreface sedimentary wedges, which occur detached from a highstand carbonate platform, and were deposited above basin marls. The amplitude of relative sea-level drop was in the order of tens of metres, with a duration of <1 Myr. The second stage of relative sea-level fall occurred within the Late Aptian and is recorded by an incised valley that, when restored to its pre-contractional attitude, was >2 km wide and cut 115 m down into the underlying Aptian succession. With the subsequent transgression, the incision was back-filled with peritidal to shallow subtidal deposits. The changes in depositional trends, lithofacies evolution and geometric relation of the stratigraphic units characterized are similar to those observed in coeval rocks within the Maestrat Basin, as well as in other correlative basins elsewhere. The pace and magnitude of the two relative sea-level drops identified fall within the glacio-eustatic domain. In the Maestrat Basin, terrestrial palynological studies provide evidence that the late Early and Late Aptian climate was cooler than the earliest part of the Early Aptian and the Albian Stage, which were characterized by warmer environmental conditions. The outcrops documented here are significant because they preserve the results of Aptian long-term sea-level trends that are often only recognizable on larger scales (i.e. seismic) such as for the Arabian Plate.

Deep incision in an Aptian carbonate succession indicates major sea-level fall in the Cretaceous

Long-term relative sea-level cycles (0 5 to 6 Myr) have yet to be fully understood for the Cretaceous. During the Aptian, in the northern Maestrat Basin (Eastern Iberian Peninsula), fault-controlled subsidence created depositional space, but eustasy governed changes in depositional trends. Relative sea-level history was reconstructed by sequence stratigraphic analysis. Two forced regressive stages of relative sea-level were recognized within three depositional sequences. The first stage is late Early Aptian age (intra Dufrenoyia furcata Zone) and is characterized by foreshore to upper shoreface sedimentary wedges, which occur detached from a highstand carbonate platform, and were deposited above basin marls. The amplitude of relative sea-level drop was in the order of tens of metres, with a duration of <1 Myr. The second stage of relative sea-level fall occurred within the Late Aptian and is recorded by an incised valley that, when restored to its pre-contractional attitude, was >2 km wide and cut 115 m down into the underlying Aptian succession. With the subsequent transgression, the incision was back-filled with peritidal to shallow subtidal deposits. The changes in depositional trends, lithofacies evolution and geometric relation of the stratigraphic units characterized are similar to those observed in coeval rocks within the Maestrat Basin, as well as in other correlative basins elsewhere. The pace and magnitude of the two relative sea-level drops identified fall within the glacio-eustatic domain. In the Maestrat Basin, terrestrial palynological studies provide evidence that the late Early and Late Aptian climate was cooler than the earliest part of the Early Aptian and the Albian Stage, which were characterized by warmer environmental conditions. The outcrops documented here are significant because they preserve the results of Aptian long-term sea-level trends that are often only recognizable on larger scales (i.e. seismic) such as for the Arabian Plate.

Axiomatization of the nucl eolus of assignment games

On the domain of general assignment games (with possible reservation prices) the core is axiomatized as the unique solution satisfying two consistency principles: projection consistency and derived consistency. Also, an axiomatic characterization of the nucleolus is given as the unique solution that satisfies derived consistency and equal maximum complaint between groups. As a consequence, we obtain a geometric characterization of the nucleolus. Maschler et al. (1979) provide a geometrical characterization for the intersection of the kernel and the core of a coalitional game, showing that those allocations that lie in both sets are always the midpoint of certain bargaining range between each pair of players. In the case of the assignment game, this means that the kernel can be determined as those core allocations where the maximum amount, that can be transferred without getting outside the core, from one agent to his / her optimally matched partner equals the maximum amount that he / she can receive from this partner, also remaining inside the core. We now prove that the nucleolus of the assignment game can be characterized by requiring this bisection property be satisfied not only for optimally matched pairs but also for optimally matched coalitions. Key words: cooperative games, assignment game, core, nucleolus

Evaluation of respiratory and dermal occupational exposures to monoethanolamine during cleaning

Professional cleaning is a basic service occupation with a wide variety of tasks carried out in all kind of different sectors and workplaces by a large workforce. One important risk for cleaning workers is the exposure to chemical substances that are present in cleaning products.Monoethanolamine was found to be often present in cleaning products such as general purpose cleaners, bathroom cleaners, floor cleaners and kitchen cleaners. Monoethanolamine can injure the skin, and exposure to monoethanolamine was associated to asthma even when the air concentrations were low. It is a strong irritant and known to be involved in sensitizing mechanisms. It is very likely that the use of cleaning products containing monoethanolamine gives rise to respiratory and dermal exposures. Therefore there is a need to further investigate the exposures to monoethanolamine for both, respiratory and dermal exposure.The determination of monoethanolamine has traditionally been difficult and analytical methods available are little adapted for occupational exposure assessments. For monoethanolamine air concentrations, a sampling and analytical method was already available and could be used. However, a method to analyses samples for skin exposure assessments as well as samples of skin permeation experiments was missing. Therefore one main objective of this master thesis was to search an already developed and described analytical method for the measurement of monoethanolamine in water solutions, and to set it up in the laboratory. Monoethanolamine was analyzed after a derivatisation reaction with o-pthtaldialdehyde. The derivated fluorescing monoethanolamine was then separated with high performance liquid chromatography and detection took place with a fluorescent detector. The method was found to be suitable for qualitative and quantitative analysis of monoethanolamine. An exposure assessment was conducted in the cleaning sector to measure the respiratory and dermal exposures to monoethanolamine during floor cleaning. Stationary air samples (n=36) were collected in 8 companies and samples for dermal exposures (n=12) were collected in two companies. Air concentrations (Mean = 0.18 mg/m3, Standard Deviation = 0.23 mg/m3, geometric Mean = 0.09 mg/m3, Geometric Standard Deviation = 3.50) detected were mostly below 1/10 of the Swiss 8h time weighted average occupational exposure limit. Factors that influenced the measured monoethanolamine air concentrations were room size, ventilation system and the concentration of monoethanolamine in the cleaning product and amount of monoethanolamine used. Measured skin exposures ranged from 0.6 to 128.4 mg/sample. Some cleaning workers that participated in the skin exposure assessment did not use gloves and had direct contact with the solutions containing the cleaning product and monoethanolamine. During the entire sampling campaign, cleaning workers mostly did not use gloves. Cleaning workers are at risk to be regularly exposed to low air concentrations of monoethanolamine. This exposure may be problematic if a worker suffers from allergic reactions (e.g. Asthma). In that case a substitution of the cleaning product may be a good prevention measure as several different cleaning products are available for similar cleaning tasks. Currently there are no occupational exposure limits to compare the skin exposures that were found. To prevent skin exposures, adaptations of the cleaning techniques and the use of gloves should be considered. The simultaneous skin and airborne exposures might accelerate adverse health effects. Overall the risks caused by exposures to monoethanolamine are considered as low to moderate when the cleaning products are used correctly. Whenever possible, skin exposures should be avoided. Further research should consider especially the dermal exposure routes, as very high exposures might occur by skin contact with cleaning products. Dermatitis but also sensitization might be caused by skin exposures. In addition, new biomedical insights are needed to better understand the risks of the dermal exposure. Therefore skin permeability experiments should be considered.

Etude des niveaux de concentration d'hydrocarbures aromatiques polycycliques (HAPs) dans la poussière de bois et des marqueurs biologiques d'effets génotoxiques chez les travailleurs du bois

L'exposition aux poussières de bois est associé à un risque accru d'adénocarcinomes des fosses nasales et des sinus paranasaux (SNC, 'Sinonasal cancer') chez les travailleurs du bois. Les poussières de bois sont ainsi reconnues comme cancérogènes avérés pour l'homme par le Centre international de Recherche sur le Cancer (CIRC). Toutefois, l'agent causal spécifique et le mécanisme sous-jacent relatifs au cancer lié aux poussières de bois demeurent inconnus. Une possible explication est une co-exposition aux poussières de bois et aux Hydrocarbures Aromatiques Polycycliques (HAP), ces derniers étant potentiellement cancérogènes. Dans les faits, les travailleurs du bois sont non seulement exposés aux poussières de bois naturel, mais également à celles générées lors d'opérations effectuées à l'aide de machines (ponceuses, scies électriques, etc.) sur des finitions de bois (bois traités) ou sur des bois composites, tels que le mélaminé et les panneaux de fibres à densité moyenne (MDF, 'Medium Density Fiberboard'). Des HAP peuvent en effet être générés par la chaleur produite par l'utilisation de ces machines sur la surface du bois. Les principaux objectifs de cette thèse sont les suivants: (1) quantifier HAP qui sont présents dans les poussières générées lors de diverses opérations courantes effectuées sur différents bois (2) quantifier l'exposition individuelle aux poussières de bois et aux HAP chez les travailleurs, et (3) évaluer les effets génotoxiques (dommages au niveau de l'ADN et des chromosomes) due à l'exposition aux poussières de bois et aux HAP. Cette thèse est composée par une étude en laboratoire (objectif 1) et par une étude de terrain (objectifs 2 et 3). Pour l'étude en laboratoire, nous avons collecté des poussières de différents type de bois (sapin, MDF, hêtre, sipo, chêne, bois mélaminé) générées au cours de différentes opérations (comme le ponçage et le sciage), et ceci dans une chambre expérimentale et dans des conditions contrôlées. Ensuite, pour l'étude de terrain, nous avons suivi, dans le cadre de leur activité professionnelle, 31 travailleurs de sexe masculin (travailleurs du bois et ébenistes) exposés aux poussières de bois pendant deux jours de travail consécutifs. Nous avons également recruté, comme groupe de contrôle, 19 travailleurs non exposés. Pour effectuer une biosurveillance, nous avons collecté des échantillons de sang et des échantillons de cellules nasales et buccales pour chacun des participants. Ces derniers ont également rempli un questionnaire comprenant des données démographiques, ainsi que sur leur style de vie et sur leur exposition professionnelle. Pour les travailleurs du bois, un échantillonnage individuel de poussière a été effectué sur chaque sujet à l'aide d'une cassette fermée, puis nous avons évalué leur exposition à la poussière de bois et aux HAP, respectivement par mesure gravimétrique et par Chromatographie en phase gazeuse combinée à la spectrométrie de masse. L'évaluation des dommages induits à l'ADN et aux chromosomes (génotoxicité) a été, elle, effectuée à l'aide du test des micronoyaux (MN) sur les cellules nasales et buccales et à l'aide du test des comètes sur les échantillons de sang. Nos résultats montrent dans la poussière de la totalité des 6 types de bois étudiés la présence de HAP (dont certains sont cancérogènes). Des différences notoires dans les concentrations ont été néanmoins constatées en fonction du matériau étudié : les concentrations allant de 0,24 ppm pour la poussière de MDF à 7.95 ppm pour le mélaminé. Nos résultats montrent également que les travailleurs ont été exposés individuellement à de faibles concentrations de HAP (de 37,5 à 119,8 ng m-3) durant les opérations de travail du bois, alors que les concentrations de poussières inhalables étaient relativement élevés (moyenne géométrique de 2,8 mg m-3). En ce qui concerne la génotoxicité, les travailleurs exposés à la poussière de bois présentent une fréquence significativement plus élevée en MN dans les cellules nasales et buccales que les travailleurs du groupe témoin : un odds ratio de 3.1 a été obtenu pour les cellules nasales (IC 95% : de 1.8 à 5.1) et un odds ratio de 1,8 pour les cellules buccales (IC 95% : de 1.3 à 2.4). En outre, le test des comètes a montré que les travailleurs qui ont déclaré être exposés aux poussières de MDF et/ou de mélaminé avaient des dommages à l'ADN significativement plus élevés que les deux travailleurs exposés à la poussière de bois naturel (sapin, épicéa, hêtre, chêne) et que les travailleurs du groupe témoin (p <.01). Enfin, la fréquence des MN dans les cellules nasales et buccales augmentent avec les années d'exposition aux poussières de bois. Par contre, il n'y a pas de relation dose-réponse concernant la génotoxicité due à l'exposition journalière à la poussière et aux HAP. Cette étude montre qu'une exposition aux HAP eu bien lieu lors des opérations de travail du bois. Les travailleurs exposés aux poussières de bois, et donc aux HAP, courent un risque plus élevé (génotoxicité) par rapport au groupe témoin. Étant donné que certains des HAP détectés sont reconnus potentiellement cancérogènes, il est envisageable que les HAP générés au cours du travail sur les matériaux de bois sont un des agents responsables de la génotoxicité de la poussière de bois et du risque élevé de SNC observé chez les travailleurs du secteur. Etant donné la corrélation entre augmentation de la fréquence des MN, le test des micronoyaux dans les cellules nasales et buccales constitue sans conteste un futur outil pour la biosurveillance et pour la détection précoce du risque de SNC chez les travailleurs. - Exposures to wood dust have been associated with an elevated risk of adenocarcinomas of the Dasal cavity and the paranasal sinuses (sinonasal cancer or SNC) among wood workers. Wood dust is recognized as a human carcinogen by the International Agency for Research on Cancer. However, the specific cancer causative agent(s) and the mechanism(s) behind wood dust related carcinogenesis remains unknown. One possible explanation is a co-exposure to wood dust and polycyclic aromatic hydrocarbons (PAH), the latter being carcinogenic. In addition, wood workers are not only exposed to natural wood but also to wood finishes and composite woods such as wood melamine and medium density fiber (MDF) boards during the manipulation with power tools. The heat produced by the use of power tools can cause the generation of PAH from wood materials. The main objectives of the present thesis are to: (1) quantify possible PAH concentrations in wood dust generated during various common woodworking operations using different wood materials; (2) quantify personal wood dust concentrations and PAH exposures among wood workers; and (3) assess genotoxic effects (i.e., DNA and chromosomal damage) of wood dust and PAH exposure in wood workers. This thesis is composed by a laboratory study (objective 1) and a field study (objectives 2 and 3). In the laboratory study we collected wood dust from different wood materials (fir, MDF, beech, mahagany, oak, and wood melamine) generated during different wood operations (e.g., sanding and sawing) in an experimental chamber under controlled conditions. In the following field study, we monitored 31 male wood workers (furniture and construction workers) exposed to wood dust during their professional activity for two consecutive work shifts. Additionally, we recruited 19 non exposed workers as a control group. We collected from each participant blood samples, and nasal and buccal cell samples. They answered a questionnaire including demographic and life-style data and occupational exposure (current and past). Personal wood dust samples were collected using a closed-face cassette. We used gravimetrie analysis to determine the personal wood dust concentrations and capillary gas chromatography - mass spectrometry analysis to determine PAH concentrations. Genotoxicity was assessed with the micronucleus (MN) assay for nasal and buccal cells and with the comet assay for blood samples. Our results show that PAH (some of them carcinogenic) were present in dust from all six wood materials tested, yet at different concentrations depending on the material. The highest concentration was found in dust from wood melamine (7.95 ppm) and the lowest in MDF (0.24 ppm). Our results also show that workers were individually exposed to low concentrations of PAHs (37.5-119.8 ng m"3) during wood working operations, whereas the concentrations of inhalable dust were relatively high (geometric mean 2.8 mg m"3). Concerning the genotoxicity, wood workers had a significantly higher MN frequency in nasal and buccal cells than the workers in the control group (odds ratio for nasal cells 3.1 (95%CI 1.8-5.1) and buccal cells 1.8 (95%CI 1.3-2.4)). Furthermore, the comet assay showed that workers who reported to be exposed to dust from wooden boards (MDF and wood melamine) had significantly higher DNA damage than both the workers exposed to natural woods (fir, spruce, beech, oak) and the workers in the control group (p < 0.01). Finally, MN frequency in nasal and buccal cells increased with increasing years of exposure to wood dust. However, there was no genotoxic dose-response relationship with the per present day wood dust and PAH exposure. This study shows that PAH exposure occurred during wood working operations. Workers exposed to wood dust, and thus to PAH, had a higher risk for genotoxicity compared to the control group. Since some of the detected PAH are potentially carcinogenic, PAH generated from operations on wood materials may be one of the causative agents for the observed increased genotoxicity in wood workers. Since increased genotoxicity is manifested in an increased MN frequency, the MN assay in nasal and buccal cells may become a relevant biomonitoring tool in the future for early detection of SNC risk.

Population receptive field estimates of human auditory cortex.

Here we describe a method for measuring tonotopic maps and estimating bandwidth for voxels in human primary auditory cortex (PAC) using a modification of the population Receptive Field (pRF) model, developed for retinotopic mapping in visual cortex by Dumoulin and Wandell (2008). The pRF method reliably estimates tonotopic maps in the presence of acoustic scanner noise, and has two advantages over phase-encoding techniques. First, the stimulus design is flexible and need not be a frequency progression, thereby reducing biases due to habituation, expectation, and estimation artifacts, as well as reducing the effects of spatio-temporal BOLD nonlinearities. Second, the pRF method can provide estimates of bandwidth as a function of frequency. We find that bandwidth estimates are narrower for voxels within the PAC than in surrounding auditory responsive regions (non-PAC).

General electromagnetic simulation tool to predict the microwave nonlinear response of planar, arbitrarily-shaped HTS structures

This work describes a simulation tool being developed at UPC to predict the microwave nonlinear behavior of planar superconducting structures with very few restrictions on the geometry of the planar layout. The software is intended to be applicable to most structures used in planar HTS circuits, including line, patch, and quasi-lumped microstrip resonators. The tool combines Method of Moments (MoM) algorithms for general electromagnetic simulation with Harmonic Balance algorithms to take into account the nonlinearities in the HTS material. The Method of Moments code is based on discretization of the Electric Field Integral Equation in Rao, Wilton and Glisson Basis Functions. The multilayer dyadic Green's function is used with Sommerfeld integral formulation. The Harmonic Balance algorithm has been adapted to this application where the nonlinearity is distributed and where compatibility with the MoM algorithm is required. Tests of the algorithm in TM010 disk resonators agree with closed-form equations for both the fundamental and third-order intermodulation currents. Simulations of hairpin resonators show good qualitative agreement with previously published results, but it is found that a finer meshing would be necessary to get correct quantitative results. Possible improvements are suggested.