Using 80 kVp versus 120 kVp in perfusion CT measurement of regional cerebral blood flow.

Perfusion CT studies of regional cerebral blood flow (rCBF), involving sequential acquisition of cerebral CT sections during IV contrast material administration, have classically been reported to be achieved at 120 kVp. We hypothesized that using 80 kVp should result in the same image quality while significantly lowering the patient's radiation dose, and we evaluated this assumption. In five patients undergoing cerebral CT survey, one section level was imaged at 120 kVp and 80 kVp, before and after IV administration of iodinated contrast material. These four cerebral CT sections obtained in each patient were analyzed with special interest to contrast, noise, and radiation dose. Contrast enhancement at 80 kVp is significantly increased (P < .001), as well as contrast between gray matter and white matter after contrast enhancement (P < .001). Mean noise at 80 kVp is not statistically different (P = .042). Finally, performance of perfusion CT studies at 80 kVp, keeping mAs constant, lowers the radiation dose by a factor of 2.8. We, thus, conclude that 80 kVp acquisition of perfusion CT studies of rCBF will result in increased contrast enhancement and should improve rCBF analysis, with a reduced patient's irradiation.

Identification of potential rockfall source areas at a regional scale using a DEM-based geomorphometric analysis

The availability of high resolution Digital Elevation Models (DEM) at a regional scale enables the analysis of topography with high levels of detail. Hence, a DEM-based geomorphometric approach becomes more accurate for detecting potential rockfall sources. Potential rockfall source areas are identified according to the slope angle distribution deduced from high resolution DEM crossed with other information extracted from geological and topographic maps in GIS format. The slope angle distribution can be decomposed in several Gaussian distributions that can be considered as characteristic of morphological units: rock cliffs, steep slopes, footslopes and plains. A terrain is considered as potential rockfall sources when their slope angles lie over an angle threshold, which is defined where the Gaussian distribution of the morphological unit "Rock cliffs" become dominant over the one of "Steep slopes". In addition to this analysis, the cliff outcrops indicated by the topographic maps were added. They contain however "flat areas", so that only the slope angles values above the mode of the Gaussian distribution of the morphological unit "Steep slopes" were considered. An application of this method is presented over the entire Canton of Vaud (3200 km2), Switzerland. The results were compared with rockfall sources observed on the field and orthophotos analysis in order to validate the method. Finally, the influence of the cell size of the DEM is inspected by applying the methodology over six different DEM resolutions.

ASIC1a oligomerization structure-function of its extracellular vestibule and functional characterization of αS243Pβɣ ENaC

Quatre cristaux du canal ASIC1a ont été publiés et soutiennent une stoechiométrie trimérique. Cependant, ces données contredisant de précédentes analyses fonctionnelles effectuées sur des canaux de la même famille, notre intérêt fut porté sur l'oligomérisation d'ASIC1a. Dans ce sens, un nouvel essai couplant la méthode d'analyse par substitution de cystéines (SCAM) avec l'utilisation de réactifs sulfhydryls bifonctionnels (crosslinkers) a été mis en place. Le but étant de stabiliser, puis sélectionner les canaux fonctionnels, pour ensuite les séparer selon leur taille par SDS-PAGE. Grâce à cette technique, nous avons démontré que le complexe stabilisé a une taille coïncidant avec une organisation tétramérique. En plus de son oligomérisation, le chemin emprunté par les ions pour traverser le canal n'est pas clairement défini dans ces structures. De ce fait, utilisant une approche électrophysiologique, nous avons étudié le lien entre la structure et la fonction du vestibule extracellulaire d'ASIC1a. Dans ce but, nous nous sommes intéressés l'accessibilité de cystéines spécifiques localisées dans ce vestibule pour des réactifs méthanethiosulfonates (MTS). Ainsi, nous avons pu corréler les cinétiques de modification de ces cystéines par les MTS avec les effets sur le courant sodique, et donc avoir des informations supplémentaires sur la voie empruntée par les ions. De plus, la simulation informatique de liaison de ces réactifs illustre le remplissage total de ce vestibule. Fonctionnellement, cette interaction ne perturbe pas le passage de ions, c'est pourquoi il nous apparaît probable que le vestibule présente une taille plus large que celle illustrée par les cristaux. Dans un deuxième temps, notre intérêt fut porté sur ENaC. Ce canal est composé des trois sous-unités (a, ß et y) et est exprimé dans divers épithéliums, dont les tubules des reins. Il participe à l'homéostasie sodique et est essentiellement régulé par voie hormonale via l'aldostérone et la Vasopressine, mais également par des sérines protéases ou le Na+. Nous avons étudié la répercussion fonctionnelle de la mutation aS243P, découverte chez un nouveau-né prématuré atteint de pseudohypoaldostéronisme de type 1. Cette maladie autosomale récessive se caractérise, généralement, par une hyponatrémie liée à d'importantes pertes de sel dans les urines, une hyperkaliémie, ainsi qu'un niveau élevé d'aldostérone. Tout d'abord aucune des expériences biochimiques et électrophysiologiques n'a pu démontrer un défaut d'expression ou une forte diminution de l'activité soutenant les données cliniques. Cependant, en challengeant aS243PßyENaC avec une forte concentration de Na+ externe, une hypersensibilité de canal fut observée. En effet, ni les phénomènes régulateurs de « feedback inhibition » ou de « Na+ self-inhibition » n'étaient semblables au canal sauvage. De ce fait, ils apparaissaient exacerbés en présence de la mutation, amenant ainsi à une diminution de la réabsorption de Na+. Ceci corrobore entièrement l'hyponatrémie diagnostiquée. Le rein d'un prématuré étant immature, la quantité de Na+ atteignant la partie distale du néphron est plus élevée, du fait que les autres mécanismes de réabsorption en amont ne sont probablement pas encore en place. Cette hypothèse est renforcée par l'existence d'un frère présentant la même mutation, mais qui, né à terme, ne présentait aucun signe d'hyponatrémie. - The main topic of my thesis is the structure-function relationship of the ENaC/Deg family of ion channels, namely the Acid-Sensing Ion Channel ASIC1a and the Epithelial Na Channel ENaC. The primary part of this research is dedicated to the structure of ASIC1a. Four channel crystals have been published, which support a trimeric stoichiometry, although these data contradict previous functional experiments on other ENaC/Deg members. We are therefore interested in ASIC1a oligomerization and have set up a new assay combining the Substituted- Cysteine Accessibility Method (SCAM) with Afunctional sulfhydryl reagents (crosslinkers) allowing its study. The aim was to first stabilize the channels, then select those that are functional and then resolve them according to their size on SDS-PAGE. We demonstrated that the stabilized complex has a molecular weight corresponding to a tetrameric stoichiometry. In addition to our interest in the oligomerization of the ENaC/Deg family of ion channels, we also wanted to investigate the thus far undefined way of permeation for these channels. Therefore, taking the advantage of a more electrophysiological approach, we studied the accessibility of specific cysteines for methanethiosulfonate reagents (MTS) and were able to correlate the MTS association kinetics on cysteine residues with Na+ currents. These results have given us an insight into ion permeation and our functional evidence indicates that the extracellular is larger than that depicted by the crystal structures. As a side project, we focused on ENaC, which is made up of three subunits (a, ß and y) and is expressed in various epithelia, especially in the distal nephron of the kidneys. It plays a role in Na+ homeostasis and is essentially regulated by hormones via aldosterone and vasopressin, but also by serine proteases or Na+. We have studied the functional impact of the aS243P mutation, discovered in a premature baby suffering from pseudohypoaldosteronism of type 1. This autosomal recessive disease is characterized by hyponatremia, hyperkalemia and high aldosterone levels. Firstly, neither biochemical nor electrophysiological experiments indicated an expression defect or a strong decrease in activity. However, challenging aS243PßyENaC with increased external Na+ concentration showed channel hypersensitivity. Indeed, both the "feedback inhibition" and the "Na+ self-inhibition" regulatory mechanisms are impaired, leading to a decrease in Na+ reabsorption, entirely supports the diagnosis. The kidneys in preterm infants are immature and Na+ levels reaching the distal nephron are higher than normally observed. We hypothesize that the upstream reabsorption machinery is unlikely to be sufficiently matured and this assumption is supported by an asymptomatic sibling carrying the same mutation, but born at term. - La cellule, unité fonctionnelle du corps humain, est délimitée par une membrane plasmique servant de barrière biologique entre les milieux intra et extracellulaires. Une communication entre cellules est indispensable pour un fonctionnement adéquat. Sa survie dépend, entre autres, du maintien de la teneur en ions dans chacun des milieux qui doivent pouvoir être réabsorbés, ou sécrétés, selon les besoins. Les protéines insérées dans la membrane forment un canal et sont un moyen de communication permettant spécifiquement à des ions tel que le sodium (Na+) de traverser. Le Na+ se trouve dans la plupart des aliments et le sel, et est spécifiquement réabsorbé au niveau des reins grâce au canal sodique épithélial ENaC. Cette réabsorption se fait de l'urine primaire vers l'intérieur de la cellule, puis est transporté vers le sang. Pour maintenir un équilibre, une régulation de ce canal est nécessaire. En effet, des dysfonctionnements impliquant la régulation ou l'activité d'ENaC lui-même sont à l'origine de maladies telles que la mucoviscidose, l'hypertension ou encore, le pseudohypoaldostéronisme (PHA). Cette maladie est caractérisée, notamment, par d'importantes pertes de sel dans les urines. Des pédiatres ont diagnostiqué un PHA chez un nouveau-né, ce dernier présentant une modification du canal ENaC, nous avons recréé cette protéine afin d'étudier l'impact de ce changement sur son activité. Nous avons démontré que la régulation d'ENaC était effectivement perturbée, conduisant ainsi à une forte réduction de la réabsorption sodique. Afin de développer des molécules capables de moduler l'activité de protéines. Il est nécessaire d'en connaître la structure. Celle du canal sodique sensible à l'acidification ASIC1, un canal cousin d'ENaC, est connue. Ces données structurales contredisant cependant les analyses fonctionnelles, nous nous sommes penchés une nouvelle fois sur ASIC1. Une protéine est une macromolécule biologique composée d'une chaîne d'acides aminés (aa). De l'enchaînement d'aa à la protéine fonctionnelle, quatre niveaux de structuration existent. Chaque aa donne une indication quant au repliement et plus particulièrement la cystéine. Arborant un groupe sulfhydryle (SH) capable de former une liaison spécifique et stable avec un autre SH, celle-ci est souvent impliquée dans la structure tridimensionnelle de la protéine. Ce type de liaison intervient également dans la stabilisation de la structure quaternaire, qui est l'association de plusieurs protéines identiques (homomère), ou pas (hétéromère). Dans cette partie, nous avons remplacé des aa par des cystéines à des endroits spécifiques. Le but était de stabiliser plusieurs homomères d'ASICl ensemble avec des réactifs créant des ponts entre deux SH. Ainsi, nous avons pu déterminer le nombre de protéines ASIC1 participant à la formation d'un canal fonctionnel. Nos résultats corroborent les données fonctionnelles soutenant un canal tétramérique. Nous avons également étudié l'accessibilité de ces nouvelles cystéines afin d'obtenir des informations supplémentaires sur la structure du chemin emprunté par le Na+ à travers ASIC1 et plus particulièrement du vestibule extracellulaire.

Role of Particle Shape on the Stress Propagation in Granular Packings

We present an experimental and numerical study on the influence that particle aspect ratio has on the mechanical and structural properties of granular packings. For grains with maximal symmetry (squares), the stress propagation in the packing localizes forming chainlike forces analogous to the ones observed for spherical grains. This scenario can be understood in terms of stochastic models of aggregation and random multiplicative processes. As the grains elongate, the stress propagation is strongly affected. The interparticle normal force distribution tends toward a Gaussian, and, correspondingly, the force chains spread leading to a more uniform stress distribution reminiscent of the hydrostatic profiles known for standard liquids

Runaway Greenhouse Effect in a Semigray Radiative-Convective Model

The effects of the nongray absorption (i.e., atmospheric opacity varying with wavelength) on the possible upper bound of the outgoing longwave radiation (OLR) emitted by a planetary atmosphere have been examined. This analysis is based on the semigray approach, which appears to be a reasonable compromise between the complexity of nongray models and the simplicity of the gray assumption (i.e., atmospheric absorption independent of wavelength). Atmospheric gases in semigray atmospheres make use of constant absorption coefficients in finite-width spectral bands. Here, such a semigray absorption is introduced in a one-dimensional (1D) radiative– convective model with a stratosphere in radiative equilibrium and a troposphere fully saturated with water vapor, which is the semigray gas. A single atmospheric window in the infrared spectrum has been assumed. In contrast to the single absolute limit of OLR found in gray atmospheres, semigray ones may also show a relative limit. This means that both finite and infinite runaway effects may arise in some semigray cases. Of particular importance is the finding of an entirely new branch of stable steady states that does not appear in gray atmospheres. This new multiple equilibrium is a consequence of the nongray absorption only. It is suspected that this new set of stable solutions has not been previously revealed in analyses of radiative–convective models since it does not appear for an atmosphere with nongray parameters similar to those for the earth’s current state

Fault diagnosis by refining the parameter uncertainty space of nonlinear dynamic systems

This paper deals with fault detection and isolation problems for nonlinear dynamic systems. Both problems are stated as constraint satisfaction problems (CSP) and solved using consistency techniques. The main contribution is the isolation method based on consistency techniques and uncertainty space refining of interval parameters. The major advantage of this method is that the isolation speed is fast even taking into account uncertainty in parameters, measurements, and model errors. Interval calculations bring independence from the assumption of monotony considered by several approaches for fault isolation which are based on observers. An application to a well known alcoholic fermentation process model is presented

Constraint satisfaction techniques under uncertain conditions for fault diagnosis in nonlinear dynamic systems

The speed of fault isolation is crucial for the design and reconfiguration of fault tolerant control (FTC). In this paper the fault isolation problem is stated as a constraint satisfaction problem (CSP) and solved using constraint propagation techniques. The proposed method is based on constraint satisfaction techniques and uncertainty space refining of interval parameters. In comparison with other approaches based on adaptive observers, the major advantage of the presented method is that the isolation speed is fast even taking into account uncertainty in parameters, measurements and model errors and without the monotonicity assumption. In order to illustrate the proposed approach, a case study of a nonlinear dynamic system is presented

Development of model observers applied to 3D breast tomosynthesis microcalcifications and masses

The development of model observers for mimicking human detection strategies has followed from symmetric signals in simple noise to increasingly complex backgrounds. In this study we implement different model observers for the complex task of detecting a signal in a 3D image stack. The backgrounds come from real breast tomosynthesis acquisitions and the signals were simulated and reconstructed within the volume. Two different tasks relevant to the early detection of breast cancer were considered: detecting an 8 mm mass and detecting a cluster of microcalcifications. The model observers were calculated using a channelized Hotelling observer (CHO) with dense difference-of-Gaussian channels, and a modified (Partial prewhitening [PPW]) observer which was adapted to realistic signals which are not circularly symmetric. The sustained temporal sensitivity function was used to filter the images before applying the spatial templates. For a frame rate of five frames per second, the only CHO that we calculated performed worse than the humans in a 4-AFC experiment. The other observers were variations of PPW and outperformed human observers in every single case. This initial frame rate was a rather low speed and the temporal filtering did not affect the results compared to a data set with no human temporal effects taken into account. We subsequently investigated two higher speeds at 5, 15 and 30 frames per second. We observed that for large masses, the two types of model observers investigated outperformed the human observers and would be suitable with the appropriate addition of internal noise. However, for microcalcifications both only the PPW observer consistently outperformed the humans. The study demonstrated the possibility of using a model observer which takes into account the temporal effects of scrolling through an image stack while being able to effectively detect a range of mass sizes and distributions.

Evidence for mantle exhumation along the Arabian margin in the Zagros (Kermanshah area, Iran)

The Kermanshah Crush Zone (Zagros, Iran) comprises elements from the Tethys Ocean and the former ocean-continent transition. Serpentinites and gabbros exposed in this area were formerly interpreted as originated from Tethys ocean and other residual Tethys oceanic domains all situated northeast of the Bisotoun platform. However, the structural relationships between these ultramafic units remained unclear. New field work in the Kermanshah-Harsin area led to the description of detachment faults over serpentinised mantle. ``Mid-Cretaceous'' carbonate ``extensional allochthons'' (pre-rift) and pelagic sediments (syn- to post-rift) dated from the Liassic are exposed above these detachments. Such an age mismatch can be explained by a polyphased mantle exhumation in a narrow basin along the Arabian margin with the assumption that no radiolarite nappe has been thrusted over the Bisotoun. Another detachment has been identified further to the NE on Eocene gabbro. So far, this one is considered as an intra-oceanic detachment from the residual Tethys. A first evolution model is proposed from early Jurassic to late Cretaceous obduction along with how this interpretation may be improved by future field work.

Calculation of Franck-Condon factors including anharmonicity: simulation of the C2 H4+ X̃2B 3u←C2 H4X̃1 Ag band in the photoelectron spectrum of ethylene

Our new simple method for calculating accurate Franck-Condon factors including nondiagonal (i.e., mode-mode) anharmonic coupling is used to simulate the C2H4+X2B 3u←C2H4X̃1 Ag band in the photoelectron spectrum. An improved vibrational basis set truncation algorithm, which permits very efficient computations, is employed. Because the torsional mode is highly anharmonic it is separated from the other modes and treated exactly. All other modes are treated through the second-order perturbation theory. The perturbation-theory corrections are significant and lead to a good agreement with experiment, although the separability assumption for torsion causes the C2 D4 results to be not as good as those for C2 H4. A variational formulation to overcome this circumstance, and deal with large anharmonicities in general, is suggested

Ab initio benchmark study for the oxidative addition of CH4 to Pd: importance of basis-set flexibility and polarization

To obtain a state-of-the-art benchmark potential energy surface (PES) for the archetypal oxidative addition of the methane C-H bond to the palladium atom, we have explored this PES using a hierarchical series of ab initio methods (Hartree-Fock, second-order Møller-Plesset perturbation theory, fourth-order Møller-Plesset perturbation theory with single, double and quadruple excitations, coupled cluster theory with single and double excitations (CCSD), and with triple excitations treated perturbatively [CCSD(T)]) and hybrid density functional theory using the B3LYP functional, in combination with a hierarchical series of ten Gaussian-type basis sets, up to g polarization. Relativistic effects are taken into account either through a relativistic effective core potential for palladium or through a full four-component all-electron approach. Counterpoise corrected relative energies of stationary points are converged to within 0.1-0.2 kcal/mol as a function of the basis-set size. Our best estimate of kinetic and thermodynamic parameters is -8.1 (-8.3) kcal/mol for the formation of the reactant complex, 5.8 (3.1) kcal/mol for the activation energy relative to the separate reactants, and 0.8 (-1.2) kcal/mol for the reaction energy (zero-point vibrational energy-corrected values in parentheses). This agrees well with available experimental data. Our work highlights the importance of sufficient higher angular momentum polarization functions, f and g, for correctly describing metal-d-electron correlation and, thus, for obtaining reliable relative energies. We show that standard basis sets, such as LANL2DZ+ 1f for palladium, are not sufficiently polarized for this purpose and lead to erroneous CCSD(T) results. B3LYP is associated with smaller basis set superposition errors and shows faster convergence with basis-set size but yields relative energies (in particular, a reaction barrier) that are ca. 3.5 kcal/mol higher than the corresponding CCSD(T) values

Oxidation of silicon: further tests for the interfacial silicon emission model

The classical description of Si oxidation given by Deal and Grove has well-known limitations for thin oxides (below 200 Ã). Among the large number of alternative models published so far, the interfacial emission model has shown the greatest ability to fit the experimental oxidation curves. It relies on the assumption that during oxidation Si interstitials are emitted to the oxide to release strain and that the accumulation of these interstitials near the interface reduces the reaction rate there. The resulting set of differential equations makes it possible to model diverse oxidation experiments. In this paper, we have compared its predictions with two sets of experiments: (1) the pressure dependence for subatmospheric oxygen pressure and (2) the enhancement of the oxidation rate after annealing in inert atmosphere. The result is not satisfactory and raises serious doubts about the model’s correctness

Information-theoretical derivation of an extended thermodynamical description of radiative systems

A radiative equation of the Cattaneo–Vernotte type is derived from information theory and the radiative transfer equation. The equation thus derived is a radiative analog of the equation that is used for the description of hyperbolic heat conduction. It is shown, without recourse to any phenomenological assumption, that radiative transfer may be included in a natural way in the framework of extendedirreversible thermodynamics

Seismic attenuation and velocity dispersion in heterogeneous partially saturated porous rocks

Using a numerical approach, we explore wave-induced fluid flow effects in partially saturated porous rocks in which the gas-water saturation patterns are governed by mesoscopic heterogeneities associated with the dry frame properties. The link between the dry frame properties and the gas saturation is defined by the assumption of capillary pressure equilibrium, which in the presence of heterogeneity implies that neighbouring regions can exhibit different levels of saturation. To determine the equivalent attenuation and phase velocity of the synthetic rock samples considered in this study, we apply a numerical upscaling procedure, which permits to take into account mesoscopic heterogeneities associated with the dry frame properties as well as spatially continuous variations of the pore fluid properties. The multiscale nature of the fluid saturation is taken into account by locally computing the physical properties of an effective fluid, which are then used for the larger-scale simulations. We consider two sets of numerical experiments to analyse such effects in heterogeneous partially saturated porous media, where the saturation field is determined by variations in porosity and clay content, respectively. In both cases we also evaluate the seismic responses of corresponding binary, patchy-type saturation patterns. Our results indicate that significant attenuation and modest velocity dispersion effects take place in this kind of media for both binary patchy-type and spatially continuous gas saturation patterns and in particular in the presence of relatively small amounts of gas. The numerical experiments also show that the nature of the gas distribution patterns is a critical parameter controlling the seismic responses of these environments, since attenuation and velocity dispersion effects are much more significant and occur over a broader saturation range for binary patchy-type gas-water distributions. This analysis therefore suggests that the physical mechanisms governing partial saturation should be accounted for when analysing seismic data in a poroelastic framework. In this context, heterogeneities associated with the dry frame properties, which do not play important roles in wave-induced fluid flow processes per se, should be taken into account since they may determine the kind of gas distribution pattern taking place in the porous rock.

Hours worked - Productivity puzzle: identification in fractional integration settings

A recent finding of the structural VAR literature is that the response of hours worked to a technology shock depends on the assumption on the order of integration of the hours. In this work we relax this assumption, allowing for fractional integration and long memory in the process for hours and productivity. We find that the sign and magnitude of the estimated impulse responses of hours to a positive technology shock depend crucially on the assumptions applied to identify them. Responses estimated with short-run identification are positive and statistically significant in all datasets analyzed. Long-run identification results in negative often not statistically significant responses. We check validity of these assumptions with the Sims (1989) procedure, concluding that both types of assumptions are appropriate to recover the impulse responses of hours in a fractionally integrated VAR. However, the application of longrun identification results in a substantial increase of the sampling uncertainty. JEL Classification numbers: C22, E32. Keywords: technology shock, fractional integration, hours worked, structural VAR, identification