微生物法沥取重金属污泥中铬的研究

本文研究了两种微生物及其组合沥取、回收用微生物法治理电镀铬废水产生的铬污泥中的铬。铬污泥富含C、N、O，含铬量为13%， 经X-光电子能谱分析铬以三价态(氢氧化铬)存在。二种微生物分别从一酸性矿水和酸性污泥中分离筛选得到，经鉴定为硫杆菌属 (Thiobacillus Beijerinek)的两个不同种，一为氧化亚铁硫杆菌(Thiobacillu ferrooxidans, TF), 另一为氧化硫硫杆菌 (Thiobacillus thiooxidans, TT)。研究并比较了不同微生物对污泥中铬的沥取能力，结果表明，TT菌沥取铬效率最高。振荡、动 态淋滤、静置等沥取方式经过研究表明动态淋滤为最佳，室温条件下(15-20℃)，污泥浓度为20g/L时，总铬沥出率达60%时所需时 间：动态淋滤为48.5h，振荡和静置方式分别为91.22，81.6h。研究了不同温度、不同起始PH、不同污泥浓度及非成熟菌液对微生 物沥取能力的影响：(1) 沥取前期，温度对铬的沥出影响较大；微生物沥取反应基本属一级反应；温度与反应速率的关系基本符合 Arrhenius方程，但沥取后期这一特点并不突出。(2) 沥取液最适起始PH为菌液自然PH；PH值的人为改变将使铬的沥出大大降低。 (3) 污泥浓度与铬的沥出呈正相关，但浓度高于30g/L时，铬的沥出量不再增加。(4) 非成熟菌液沥出铬的能力较差，但沥取液中 微生物生长繁殖较为活跃。总结微生物沥取反应最佳沥取条件为：TT成熟菌液、污泥浓度10g/L、温度25-36℃、动态淋滤方式，此 时铬几乎可100%从污泥中沥出。经扫描电镜分析，沥取开始时，微生物紧密吸附于污泥颗粒表面上，表面紧密吸附为微生物发挥功 能提供了基础。微生物沥取污泥中铬的反应机理推测为：硫细菌代谢产硫酸或氧化Fe2+成Fe3+，利用酸，Fe3+ 及自身氧化酶系统 氧化污泥中Cr3+为Cr6+,Cr6+溶出结晶为CrO3。This paper has studied bioleaching and recovery of Chronium(Cr)from electroplating sludge by two consortum of bacteria and their combination, with sludge produced by microbiological process treating electroplating wastewater containing Cr as material. The share of Cr is 13% and its state is Cr (OH)3 in the sludge. One of the bacteria in the paper was isolated from acid sewage sludge and the other was from acid mineral water. The former was tested and determined as Thiobacillus ferroxidans(TF) and the latter was Thiobacillus thiooxidans(TT). Different microorganisms, responsible for the metal leaching activity, have great influence on the efficiency of leaching. The results showed that TT has biggest power. Experiments were conducted to examined effects of three different ways of leaching(Shaking, Down-leaching, Static-leaching). When temperature was in-door's (15-20℃)and concentration of the sludge was 20g/L, the bioleaching time required to reach 60% of Cr solubilization with the above three ways were 91.2, 48.5, 81.6h respectively. Down-leaching was proved to be the most efficient. The influence of different temperature, initial PH, concentration of the sludge and non-mature inoculum had been studied. The results obtained reveal that: (1) The variation of temperature is important during the time from initial to middle of leaching. The reaction of bioleaching belongs to first-order. The relation between the bioleaching rate constant(In k)and temerature can be expressed by Arrhenius function. (2) The fittest initial PH is the nature PH of mature inoculum. Any alteration with it could cause clearly negative effection. (3) The concentration of the sludge can make strong influence on the bioleaching efficiency. But when the concentration is above 30g/L, the increasing of Cr in the solution is little. (4) If non-mature inoculum acts as the bioleachin microorganism, little quantity of Cr would be gained from the sludge. But the micormass in the solution is very active. The results from electron microscope showed that microorganisms adhered to the surface of the sludge and the adherence was the first stage of the bioleaching. Some salts of Cr can be obtained afer the water of the bioleaching solution being evaporated. By analysing the results of experiment with X-Ray spectroscopy, the salt was identified as CrO3. The recovery rate of Cr is 78.4%.

功能菌剂的混合发酵研究

随着化工行业的发展，大量有毒有害难降解有机物随工业废水的排放进入环境，这些物质能够在环境中长期存在、积累和扩散，通过食物链对动植物的生存及人类的健康造成不良影响。本文以苯酚、对氯硝基苯、氯苯和十六烷为模拟污染物，以前期研制的功能菌剂为对象，经过紫外线线诱变筛选出优于出发菌株的功能菌，对诱变后功能菌的理化性能进行了研究，对菌种进行了鉴定，在此基础上，就其相互之间的微生态关系进行研究，为混合发酵提供理论基础，并就其最佳发酵条件及发酵参数进行了研究，最后对发酵产品的性能进行了检测。目前，国内外有关功能菌剂的研究还存在多方面的不足，主要包括：①由于多菌种混合发酵过程较为复杂，各菌之间存在复杂的相互作用，影响因素较多，关于菌种之间的相互关系研究得很少，环境功能菌剂的发酵方法大多采用单独发酵后混合的方式。单独发酵对原材料、设备和能源的利用率较低，对于多菌种制剂发酵，在设备、能源和原材料的方面造成的浪费更大，将会大幅增加菌剂的生产成本，影响多菌种功能菌剂的发展；②功能菌剂生产过程的质量控制方面研究得较少；③功能菌剂产品的稳定性、抗冲击性能研究得较少，对环境微生物制剂的研究主要集中在菌种选育和培养条件优化方面。 通过本论文研究，得到以下主要结论。 （1）在紫外线诱变处理中，用紫外线对发生一定程度退化的出发菌株进行诱变处理后，六株具有高效降解性能的菌株被筛选出来，诱变筛选出的菌株形态和ERIC-PCR指纹图谱与出发菌株相比发生了明显改变；而且诱变后的菌株对目标难降解底物的降解能力均得到改善，其中，FPN、FCB、F14、FEm对目标底物的降解率提高了20%以上；诱变后菌株经过7次连续传代接种后，对目标难降解底物的降解率无显著变化，具有一定的遗传稳定性。并对诱变后的功能菌进行了初步的鉴定，这6株菌都分别是芽孢杆菌。 （2）对诱变后的功能菌相互之间的微生态关系进行了研究，通过抑菌实验、生长量以及基质消耗量的比较，确定它们之间的生长关系是无害共栖关系，可以进行混合发酵。 （3）对该功能菌剂进行发酵培养条件研究，结果表明发酵培养基的最佳成分（g/L）：葡萄糖 31.0g/L、玉米粉10.0g/L、磷酸氢二钾1.0g/L、硫酸铵1.1g/L、硫酸镁0.55g/L。通过研究不同的培养条件对菌体生长和降解性能的影响，确定了最佳培养条件：培养基初始pH7.5；最适温度32℃；培养基装液量125mL（250 mL三角瓶），以及培养时间对降解性能的影响，培养20 h的产物对降解最为有利。通过研究添加不同目标污染物对菌体生长和降解性能的影响，确定了添加目标污染物的最佳量以及最佳时间：苯酚投加量：1.125 g/L，对氯硝基苯投加量：0.1 g/L；最佳投加时间为发酵培养开始后4 h。 （4）以摇瓶分批发酵最优条件为基础，对FPN、F10、FCB、FNa、F14 和 FEm进行了摇瓶分批发酵试验。以摇瓶分批发酵试验数据为依据，对功能菌剂分批发酵动力学进行了研究，建立了菌体生长和基质消耗的动力学模型，拟合模型能较好的反映功能菌剂分批发酵过程。 （5）功能菌剂和活性污泥协同作用，可以提高系统的生物降解能力，功能菌剂投加量为2%，新鲜活性污泥3500 mg/L，降解24 h条件下，功能菌剂和活性污泥的协同作用对COD的去除率和对照组相比，最多的提高了36.8%。功能菌剂和活性污泥协同作用以及活性污泥的单独作用，其生物降解过程均符合一级反应动力学过程，功能菌剂和活性污泥协同作用的生物降解动力学方程为：，相关系数97%。采用SBR运行方式，引入功能菌剂的SBR系统明显能够改善和提高生物降解的效率。与仅有活性污泥的系统相比，系统对COD的平均去除率可以提高27.1%，同时，系统的耐负荷冲击以及耐毒害冲击的性能比仅有活性污泥的SBR系统强，特别是负荷冲击对引入功能菌剂的SBR系统影响很小。仅有活性污泥的SBR系统经过负荷冲击和毒害冲击之后，不能恢复到冲击之前的水平，而且系统有效作用时间的周期比引入功能菌剂的SBR系统相比大大缩短，而引入功能菌剂的SBR系统处理效果较为稳定，恢复能力很强。 Along with the development of industries, many recalcitrant organic chemicals have been discharged into natural environments together with wastewaters and can exist in waters, soil and sediments for a long time without degradation. These haz-ardous substances, their byporducts and metabolizabilities can be highly toxic, mu-tagenic and carcinogenic, thereby threatening animals, plants and human health through food chain. Consequently the removal of these compounds is of significant interest in the area of wastewater treatment. In this dissertation, the phenol, hydro-quinone, chlorobenzene and hexadecane treated as the model pollutants, the func-tional microorganism agent was used as the starting strains, they treated with ultra-violet light, and then the mutant strains with high degradation ability were screened out and identified primarily, the relationship between these stains were studied, the medium composition and fermentation conditions were optimized, the degradation ability of the fermented production was tested. The literature survey indicates that the study of the microorganism agent is far from complete and more information is re-quired on following problems. 1, Because of the complexity of relationship in mixed fermentation and the complicated factors, the study is hardly to process.2, There is a lack of information on the quality control of the producing process .3, And there is a lack of information on the stability about the microorganism agent. In this dissertation, the main results of the present study could be summarized as follows: (1)The degenerate starting strains were treated with the ultraviolet light, and six mutant strains with high biodegradation ability were screened out by using the me-dium with selective pressure of model pollutants. The mutant strains had great changes in colonialmorphology and ERIC-PCR fingerprinting. And the mutant strains got obvious advantages over the starting strains in degradation ability and over 20% improvement of removal rates was achieved for FPN、FCB、F14 and FEm. The de-gradation ability of the mutant strains was stable after seven generations. After that, the mutant strains were primarily identified as bacillus respectively. (2) The relationship between these mutant strains was studied. By the compari-son of antibiosis effect, biomass and consumption of substrate, the relationships were neutralism and they could be mixed fermented. (3) The optimized cultivation conditions were as follows: glucose 31.0 g/L, corn power 10 g/L, K2HPO4 1.0 g/L, (NH4)2SO4 1.1 g/L, MgSO4 0.55 g/L, initial pH7.5, temperature 32℃, working volume 125 mL/250 mL, and cultivation time 20h (con-sidering the time effect on degradation ability), adding pollutants phenol (1.125 g/L) and hydroquinone (0.1 g/L) into the broth at 4 h after cultivation. (4) Based on the above optimum condition, the batch fermentation was per-formed with strains FPN, F10, FCB, FNa, F14 and FEm in shake flask. The batch fermentation kinetics was studied based on the experimental data. Two kinetic models were constructed which could reflect the regularity of growth and substrate consump-tion in the process of batch fermentation. (5) The co-operation of functional microorganism agent and activated sludge could raise biodegradation of system by adding some microorganism agent and 3500 mg/L fresh activated sludge. Bioaugumentation by the addition of high effective deg-radation culture enhanced the treatment effect of SBR system and the COD removal rate was increased by 20%-36.8%. Its biodegradation matched first-order dynamical reaction equation, and the reaction equation was ln0.2327.391ct=−+. The micro-organism agent had the effect of optimization to activated sludge micro-ecosystem. The SBR system adding 2% microorganism agent, the average COD removal rate of that was increased by 27.1% and stronger anti-shock ability to load and toxicant were achieved (compared with SBR system just adding activated sludge). Especially the load-shock has barely effect to the SBR system adding microorganism agent. After the load and toxicant shock, the SBR system just adding activated sludge couldn’t come back to original level and the activated sludge micro-ecosystem was frustrated. The applying of microorganism agent increased biological activity and system’s re-sistance ability to load shock and toxicant shock.

重离子加速器中的软件无线电应用

This paper primarily elaborates automatic gain control design method in software radio receiver. It mainly uses in-phase and quadrature components quadratic sum to subtract the expectation of the output power to get the error statistic of the plus. The error statistic of the plus is smoothed by first order digital filter, and then is used to gain the output signals of controller. Thereby, it can make the system work well in certain dynamic region area of signals. It is designed for the Cooling Storage Ring ...中文文摘：本文主要阐述了软件无线电接收机中的相干AGC设计,主要利用了同相和正交支路的平方和与所期望的信号输出功率值相减,得到增益的误差统计量。该误差统计量经过一阶数字滤波器平滑,然后用于控制器输出信号的增益,从而使系统在一定的信号动态范围内都能工作。该设计主要用于兰州重离子加速器冷却存贮环的主环(CSRm)的重离子束团踢轨(Kicker System)的精确控制。

Energy-level shifts of a stationary hydrogen atom in a static external gravitational field with Schwarzschild geometry

he first order perturbations of the energy levels of a stationary hydrogen atom in a static external gravitational field, with Schwarzschild metric, are investigated. The energy shifts are calculated for the relativistic 1S, 2S, 2P, 3S, 3P, 3D, 4S, 4P, 4D, and 4F levels. The results show that the energy-level shifts of the states with total angular momentum quantum number 1/2 are all zero, and the ratio of absolute energy shifts with total angular momentum quantum number 5/2 is 145. This feature can be used to help us to distinguish the gravitational effect from other effects.

Gravitational corrections to energy-levels of a hydrogen atom

The first-order perturbations of the energy levels of a hydrogen atom in central internal gravitational field are investigated. The internal gravitational field is produced by the mass of the atomic nucleus. The energy shifts are calculated for the relativistic 1S, 2S, 2P, 3S, 3P, 3D, 4S, and 4P levels with Schwarzschild metric. The calculated results show that the gravitational corrections are sensitive to the total angular momentum quantum number.

Emittance estimation by an ion optical element with variable focusing strength and a viewing target

The emittance of an extracted ion beam can be estimated to first order by a series of three linear independent profile measurements. This estimation is restricted to the evaluation of an upper limit of the emittance value for a homogeneous, nonfilamented beam. The beam is assumed to be round, respectively elliptical, without any structure of the intensity distribution, no space charge has been assumed for the drifting beam, and the optics is assumed to be linear. Instead of using three different drift sections, a linear focusing element with three different focusing strengths can be used. Plotting the beam radius as function of focusing strength, three independent solutions can be used to calculate the Twiss parameters alpha, beta, and gamma and furthermore the emittance epsilon. Here we describe the measurements which have been performed with the SECRAL ion source at Institute of Modern Physics Lanzhou.

Chemisorption and reaction characteristics of methyl radicals on Cu(110)

Methyl radicals are generated by pyrolysis of azomethane, and the condition for achieving neat adsorption on Cu(110) is described for studying their chemisorption and reaction characteristics. The radical-surface system is examined by X-ray photoemission spectroscopy, ultraviolet photoemission spectroscopy, temperature-programmed desorption, low-energy electron diffraction (LEED), and high-resolution electron energy loss spectroscopy under ultrahigh vacuum conditions. It is observed that a small fraction of impinging CH3 radicals decompose into methylene possibly on surface defect sites. This type of CH2 radical has no apparent effect on CH3(ads) surface chemistry initiated by dehydrogenation to form active CH2(ads) followed by chain reactions to yield high-mass alkyl products. All thermal desorption products, such as H-2, CH4, C2H4, C2H6, and C3H6, are detected with a single desorption peak near 475 K. The product yields increase with surface coverage until saturation corresponding to 0.50 monolayer of CH3(ads). The mass distribution is, however, invariant with initial CH3(ads) coverage, and all desorbed species exhibit first-order reaction kinetics. LEED measurement reveals a c(2 x 2) adsorbate structure independent of the amount of gaseous exposure. This strongly suggests that the radicals aggregate into close-packed two-dimensional islands at any exposure. The islanding behavior can be correlated with the reaction kinetics and is deemed to be essential for the chain propagation reactions. Some relevant aspects of the CH3/Cu(111) system are also presented. The new results are compared with those of prior studies employing methyl halides as radical sources. Major differences are found in the product distribution and desorption kinetics, and these are attributed to the influence of surface halogen atoms present in those earlier investigations.

Kinetic study on the photo-catalytic degradation of pyridine in TiO2 suspension systems

It has been generally agreed that pyridine can be effectively mineralized in aerated TiO2 slurries using near-UV irradiation. The knowledge on the kinetics of the system possesses both practical and theoretical values. The present study, on the base of Langmuir-Hinshewood mechanism, illustrates a pseudo first-order kinetic model of the degradation with the limiting rate constant of 3.004 mg l(-1) min(-1) and equilibrium adsorption constant 2.763 x 10(-2) l mg(-1), respectively. The degradation efficiency in alkali is a little higher than that in acid with a minimum at about pH = 5, which is explained by the formation of acid-pyridine in acidic surrounding together with the amphoteric nature of the TiO2 surface. The promotion of H2O2 on the photo-degradation ties in its supplying proper amount of (OH)-O-. radicals for the inducement stage before surface redox reactions. (C) 2004 Elsevier B.V. All rights reserved.

Multipolar model for collisional quantum interference on rotational energy transfer

A theoretical model of collisional quantum interference (CQI) is developed in a diatom-diatom system based on the first-order Born approximation of time-dependent perturbation theory and the multipolar interaction potential. The transition cross section is obtained. The relations between the differential and integral interference angles are discussed. The key factors on the determination of the differential and integral interference angles are obtained. The changing tendency of the interference angles with the experimental temperatures is obtained.

基于一阶迁移系统的限界模型检测工具实现

为了简化在限界模型检测过程中模型的建立过程,给出了一种采用基于一阶迁移系统语言的模型建立方法,并在此一阶迁移系统语言中加入了通道的功能,增强了描述能力。然后在此基础上完成了一个以基于插值和k步归纳的限界验证算法为核心的模型检测工具(BMCF),最后利用该工具对常见的互斥协议,简单数据传输协议的性质进行了分析与验证。结果表明,利用该工具对系统进行建模具有方便直观的特点,并借助实现的验证算法能高效的检验性质的正确性,如果性质不成立工具还会给出反例提示。

AGET ATRP of acrylamide in aqueous media

The recently developed initiation system, the activator generated by electron transfer (AGET) was used in atom transfer radical polymerization (ATRP) to synthesize well-controlled polyacrylamide in aqueous media at 25 degrees C. The different reducing agents involved ascorbic acid and glucosa; well-controlled polymers were obtained when ascorbic acid was used as water-soluble reducing agent. The polymerizations targeted at degrees of polymerization in the range of 400 resulted in polymers with low polydispersity indices. Moreover, first order plots were linear.

Living polymerization of 1,3-butadiene by a Ziegler-Natta type catalyst composed of iron(III) 2-ethylhexanoate, triisobutylaluminum and diethyl phosphite

Living characteristics of facilely prepared Ziegler-Natta type catalyst system consisting of iron(III) 2-ethylhexanoate, triisobutylaluminum and diethyl phosphite have been found in the polymerization of 1,3-butadiene in hexane at 40 degrees C. The characteristics have been well demonstrated by: a first-order kinetics with respect to monomer conversion, a narrow molecular weight distribution (M-w/M-n = 1.48-1.52) of polybutadiene in the entire range of polymerization conversion and a good linearity between M-n and the yield of polymer. Feasible post-polymerization of 1,3-butadiene and block co-polymerization of 1,3-butadiene and isoprene further support the living natures of the catalyst bestowed with.

Monitoring catalytic degradation of dye molecules on silver-coated ZnO nanowire arrays by surface-enhanced Raman spectroscopy

Catalytic degradation of organic dye molecules has attracted extensive attention due to their high toxicity to water resources. In this paper, we propose a novel method for the fabrication of uniform silver-coated ZnO nanowire arrays. The degradation of typical dye molecule rhodamine 6G (R6G), as an example, is investigated in the presence of the as-prepared silver-coated ZnO nanowire arrays. The experimental results show that such composite nanostructures exhibit high catalytic activity, and the reaction follows pseudo-first-order kinetics. Furthermore, these nanowire arrays are desirable SERS substrates for monitoring the catalytic degradation of dye molecules. Compared with traditional UV-visible spectroscopy, SERS technology can reflect more truly the catalytic degradation process occurring on the surface of the catalysts.

A quantitative HPLC method for determining lactide content using hydrolytic kinetics

A new method for quantitative analysis of lactide has been developed by applying chemical kinetics to a HPLC system. The most important advance is its practical approach to the quantification of analytes that are unstable in the HPLC mobile phase. In HPLC analysis, anhydrous mobile phases cannot separate lactide from impurities, and only mixtures of water and organic solvent can achieve effective separation. By selecting conditions for testing and studying the kinetics of lactide hydrolysis, extensive experiments revealed that lactide degradation can be treated as a pseudo-first-order reaction under the given HPLC conditions, and lactide content or purity can be quantitatively determined. This method is practical for measuring the purity of the intermediate lactide in polylactic acid (PLA) production and the lactide content in PLA.

Polymerization of 2,2 '-Dimethyltrimethylene Carbonate by Lutetium Complexes Bearing Amino-Phosphine Ligands

A series of lutetium alkyl, amino, and guanidinato complexes based upon an amino-phosphine ligand framework had been prepared. These complexes were applied to initiate ring-opening polymerization of 2,2'-dimethyltrimethylene carbonate (DTC). The type of the initiator significantly influenced the catalytic activity of these complexes in a trend as follows: alkyl approximate to guanidinate > amide, whereas the complexes with flexible backbone between P and N atoms within the ligand exhibited higher activity than those with rigid backbone. The isolated PDTC had bimodal-mode molecular weight distribution. The molecular weights of each fraction increased linearly with the conversion, indicating that there might be two active species. This had been confirmed by analyses of oligomeric DTC living species and oligomer with NMR technique as the metal-alkoxide and the four-membered metallocyclic lactate. Kinetic investigation displayed that the polymerization rate was the first order with the monomer concentration.