Microstructure of shear localization in low-carbon ferrite pearlite steel

A study has been made of the microstructure of the thermally assisted band in a low carbon ferrite-pearlite steel, resulting from high speed torsional testing with an average strain rate of about 1500 s−1. Metallographic examination showed that there are several fine shear bands distributed over a deformed region (the gauge length of the specimen). The width of these bands is estimated to be of the order of magnitude of 50 μm, and the spacing between them is roughly about 100 μm. Detailed scanning electron microscopy studies indicate that damage of the microstructure within the band is very apparent, as evidenced by microcrack initiation and coalescence along the shear deformation band. However, there is no evidence that the material in the band had become microcrystalline or non-crystalline.

Additional response: Additional discussion of “Mixed mode ductile fracture using the strain energy density criterion”

boundary-layer flows, the skin friction and wall heat-transfer are higher and the

Response: Discussion of “Mixed Mode ductile fracture using the strain energy density criterion,” by E.E. Gdoutos

thermal conduction, and acoustic wave propagation are included. This

Application of the strain energy density criterion to ductile fracture

The strain energy density criterion due to Sih is used to predict fracture loads of two thin plates subjected to large elastic-plastic deformation. The prediction is achieved with a finite element analysis which is based on Hill's variational principle for incremental deformations capable of solving gross yielding problems involving arbitrary amounts of deformation. The computed results are in excellent agreement with those obtained in Sih's earlier analysis and with an experimental observation.

Ductile crack propagation with the strain-energy density criterion

The strain energy density criterion is used to characterize subcritical crack growth in a thin aluminum alloy sheet undergoing general yielding. A finite element analysis which incorporates both material and geometrical nonlinear behaviors of the cracked sheets is developed to predict fracture loads at varying crack growth increments. The predicted results are in excellent agreement with those measured experimentally, thus confirming the validity of the strain energy density criterion for characterizing ductile crack propagation.

Mixed-mode fracture mechanisms near the fatigue threshold of aisi-316 stainless-steel

Near threshold, mixed mode (I and II), fatigue crack growth occurs mainly by two mechanisms, coplanar (or shear) mode and branch (or tensile) mode. For a constant ratio of ΔK_I/ΔK_II the shear mode growth shows a self-arrest character and it would only start again when ΔK_I and ΔK_II are increased. Both shear crack growth and the early stages of tensile crack growth, are of a crystallographic nature; the fatigue crack proceeds along slip planes or grain boundaries. The appearance of the fracture surfaces suggest that the mechanism of crack extension is by developing slip band microcracks which join up to form a macrocrack. This process is thought to be assisted by the nature of the plastic deformation within the reversed plastic zone where high back stresses are set up by dislocation pile-ups against grain boundaries. The interaction of the crack tip stress field with that of the dislocation pile-ups leads to the formation of slip band microcracks and subsequent crack extension. The change from shear mode to tensile mode growth probably occurs when the maximum tensile stress and the microcrack density in the maximum tensile plane direction attain critical values.

脆性涂层/韧性基体材料在拉伸应变作用下的开裂行为

提出一种在脆性涂层/韧性基体材料中含弹塑性界面层的剪滞模型.研究脆性涂层/韧性基体材料在拉伸应变作用下,其表面脆性涂层的开裂行为特征,探讨涂层内正应力、界面切应力、涂层的裂纹密度与涂层几何、力学等参数之间的内在联系,获得了涂层内正应力、界面切应力和(饱和)裂纹密度的解析表达式.最后利用这些参量及其间的内在联系,以工程实际中的脆性Cr涂层/韧性钢基体材料为研究对象,研究该种材料在拉伸过程中出现的断裂行为特征.研究结果表明,该材料在拉伸应变作用下出现的饱和裂纹密度与理论结果预测值符合较好.

Substrate Strain and Proliferation & Differentiation of Bone Marrow Mesenchymal Stem Cells

New methods of surface modification of transparent silicone substrate were developed, and a new set of cell culture devices that provide homogeneous substrate strain was designed. Using the new device, effects of cyclic substrate strain on bone marrow mesenchymal stem cells(MSCs) were studied. It was found that cyclic strain influenced proliferation and differentiation of bone marrow MSCs in different ways.