Acoustic emission for diesel engine monitoring: A review and preliminary

Vibration analysis has been a prime tool in condition monitoring of rotating machines, however, its application to internal combustion engines remains a challenge because engine vibration signatures are highly non-stationary that are not suitable for popular spectrum-based analysis. Signal-to-noise ratio is a main concern in engine signature analysis due to severe background noise being generated by consecutive mechanical events, such as combustion, valve opening and closing, especially in multi-cylinder engines. Acoustic Emission (AE) has been found to give excellent signal-to-noise ratio allowing discrimination of fine detail of normal or abnormal events during a given cycle. AE has been used to detect faults, such as exhaust valve leakage, fuel injection behaviour, and aspects of the combustion process. This paper presents a review of AE application to diesel engine monitoring and preliminary investigation of AE signature measured on an 18-cylinder diesel engine. AE is compared with vibration acceleration for varying operating conditions: load and speed. Frequency characteristics of AE from those events are analysed in time-frequency domain via short time Fourier trasform. The result shows a great potential of AE analysis for detection of various defects in diesel engines.

Towards the development of a gas sensor system for monitoring pollutant gases in the low troposphere using small unmanned aerial vehicles

The world is facing problems due to the effects of increased atmospheric pollution, climate change and global warming. Innovative technologies to identify, quantify and assess fluxes exchange of the pollutant gases between the Earth’s surface and atmosphere are required. This paper proposes the development of a gas sensor system for a small UAV to monitor pollutant gases, collect data and geo-locate where the sample was taken. The prototype has two principal systems: a light portable gas sensor and an optional electric–solar powered UAV. The prototype will be suitable to: operate in the lower troposphere (100-500m); collect samples; stamp time and geo-locate each sample. One of the limitations of a small UAV is the limited power available therefore a small and low power consumption payload is designed and built for this research. The specific gases targeted in this research are NO2, mostly produce by traffic, and NH3 from farming, with concentrations above 0.05 ppm and 35 ppm respectively which are harmful to human health. The developed prototype will be a useful tool for scientists to analyse the behaviour and tendencies of pollutant gases producing more realistic models of them.

Domestic energy monitoring in Victorian households with PV solar installations : feasibility report for GV Community Energy

Australia requires decisive action on climate change and issues of sustainability. The Urban Informatics Research Lab has been funded by the Queensland State Government to conduct a three year study (2009 – 2011) exploring ways to support Queensland residents in making more sustainable consumer and lifestyle choices. We conduct user-centred design research that inform the development of real-time, mobile, locational, networked information interfaces, feedback mechanisms and persuasive and motivational approaches that in turn assist in-situ decision making and environmental awareness in everyday settings. The study aims to deliver usable and useful prototypes offering individual and collective visualisations of ecological impact and opportunities for engagement and collaboration in order to foster a participatory and sustainable culture of life in Australia. Raising people’s awareness with environmental data and educational information does not necessarily trigger sufficient motivation to change their habits towards a more environmentally friendly and sustainable lifestyle. Our research seeks to develop a better understanding how to go beyond just informing and into motivating and encouraging action and change. Drawing on participatory culture, ubiquitous computing, and real-time information, the study delivers research that leads to viable new design approaches and information interfaces which will strengthen Australia’s position to meet the targets of the Clean Energy Future strategy, and contribute to the sustainability of a low-carbon future in Australia. As part of this program of research, the Urban Informatics Research Lab has been invited to partner with GV Community Energy Pty Ltd on a project funded by the Victorian Government Sustainability Fund. This feasibility report specifically looks at the challenges and opportunities of energy monitoring in households in Victoria that include a PV solar installation. The report is structured into two parts: In Part 1, we first review a range of energy monitoring solutions, both stand-alone and internet-enabled. This section primarily focusses on the technical capacilities. However, in order to understand this information and make an informed decision, it is crucial to understand the basic principles and limitations of energy monitoring as well as the opportunities and challenges of a networked approach towards energy monitoring which are discussed in Section 2.

Traffic and climate change impacts on water quality : measuring build-up and wash-off of heavy metals and petroleum hydrocarbons

Understanding the impacts of traffic and climate change on water quality helps decision makers to develop better policy and plans for dealing with unsustainable urban and transport development. This chapter presents detailed methodologies developed for sample collection and testing for heavy metals and total petroleum hydrocarbons, as part of a research study to investigate the impacts of climate change and changes to urban traffic characteristics on pollutant build-up and wash-off from urban road surfaces. Cadmium, chromium, nickel, copper, lead, iron, aluminium, manganese and zinc were the target heavy metals, and selected gasoline and diesel range organics were the target total petroleum hydrocarbons for this study. The study sites were selected to encompass the urban traffic characteristics of the Gold Coast region, Australia. An improved sample collection method referred to as ‘the wet and dry vacuum system’ for the pollutant build-up, and an effective wash-off plan to incorporate predicted changes to rainfall characteristics due to climate change, were implemented. The novel approach to sample collection for pollutant build-up helped to maintain the integrity of collection efficiency. The wash-off plan helped to incorporate the predicted impacts of climate change in the Gold Coast region. The robust experimental methods developed will help in field sample collection and chemical testing of different stormwater pollutants in build-up and wash-off.

Foundations of International Climate Law : Objectives, principles and methods

This chapter explores the objectives, principle and methods of climate law. The United Nations Framework Convention on Climate Change (UNFCCC) lays the foundations of the international regime by setting out its ultimate objectives in Article 2, the key principles in Article 3, and the methods of the regime in Article 4. The ultimate objective of the regime – to avoid dangerous anthropogenic interference – is examined and assessments of the Intergovernmental Panel on Climate Change (IPCC) are considered when seeking to understand the definition of this concept. The international environmental principles of: state sovereignty and responsibility, preventative action, cooperation, sustainable development, precaution, polluter pays and common but differentiated responsibility are then examined and their incorporation within the international climate regime instruments evaluated. This is followed by an examination of the methods used by the mitigation and adaptation regimes in seeking to achieve the objective of the UNFCCC. Methods of the mitigation regime include: domestic implementation of policies, setting of standards and targets and allocation of rights, use of flexibility mechanisms, and reporting. While it is noted that methods of the adaptation regime are still evolving, the latter includes measures such as impact assessments, national adaptation plans and the provision of funding.

Using mobile technology and augmented reality to increase data reliability for environmental assessment

Climate change and land use pressures are making environmental monitoring increasingly important. As environmental health is degrading at an alarming rate, ecologists have tried to tackle the problem by monitoring the composition and condition of environment. However, traditional monitoring methods using experts are manual and expensive; to address this issue government organisations designed a simpler and faster surrogate-based assessment technique for consultants, landholders and ordinary citizens. However, it remains complex, subjective and error prone. This makes collected data difficult to interpret and compare. In this paper we describe a work-in-progress mobile application designed to address these shortcomings through the use of augmented reality and multimedia smartphone technology.

Increasing Food Production Sustainably in a Changing Climate : Understanding the Pressures and Potential

Australian agriculture is faced with the dilemma of increasing food production for a growing domestic and world population while decreasing environmental impacts and supporting the social and economic future of regional communities. The challenge for farmers is compounded by declining rates of productivity growth which have been linked to changes in climate and decreasing investment in agricultural research. The answer must lie in understanding the ecological functionality of landscapes and matching management of agricultural systems and use of natural resources to landscape capacity in a changing climate. A simplified mixed grain and livestock farm case study is used to illustrate the challenges of assessing the potential for shifts in land allocation between commodities to achieve sustainable intensification of nutrition production. This study highlights the risks associated with overly-simplistic solutions and the need for increased investment in research to inform the development of practical strategies for increasing food production in Australian agro-ecosystems while managing the impacts of climate change and addressing climate change mitigation policies.

Book Review : Criminological and Legal Consequences of Climate Change. Edited by Stephen Farrell, Tawhida Ahmed and Duncan French (Oxford : Hart Publishing, 272 pp.)

The book addresses a number of pressing social and environmental issues of global concern. It takes the reader on a socio-legal journal of climate change and explores a range of challenging and complex topics including renewable energies, emissions reduction, carbon trading, deforestation, migration and corporate governance.

Synergies and goal conflicts for climate change policy and spatial planning

The purpose of this paper is to identify goal conflicts – both actual and potential – between climate and social policies in government strategies in response to the growing significance of climate change as a socioecological issue (IPCC 2007). Both social and climate policies are political responses to long-term societal trends related to capitalist development, industrialisation, and urbanisation (Koch, 2012). Both modify these processes through regulation, fiscal transfers and other measures, thereby affecting conditions for the other. This means that there are fields of tensions and synergies between social policy and climate change policy. Exploring these tensions and synergies is an increasingly important task for navigating genuinely sustainable development. Gough et al (2008) highlight three potential synergies between social and climate change policies: First, income redistribution – a traditional concern of social policy – can facilitate use of and enhance efficiency of carbon pricing. A second area of synergy is housing, transport, urban policies and community development, which all have potential to crucially contribute towards reducing carbon emissions. Finally, climate change mitigation will require substantial and rapid shifts in producer and consumer behaviour. Land use planning policy is a critical bridge between climate change and social policy that provides a means to explore the tensions and synergies that are evolving within this context. This paper will focus on spatial planning as an opportunity to develop strategies to adapt to climate change, and reviews the challenges of such change. Land use and spatial planning involve the allocation of land and the design and control of spatial patterns. Spatial planning is identified as being one of the most effective means of adapting settlements in response to climate change (Hurlimann and March, 2012). It provides the instrumental framework for adaptation (Meyer, et al., 2010) and operates as both a mechanism to achieve adaptation and a forum to negotiate priorities surrounding adaptation (Davoudi, et al., 2009). The acknowledged role of spatial planning in adaptation however has not translated into comparably significant consideration in planning literature (Davoudi, et al., 2009; Hurlimann and March, 2012). The discourse on adaptation specifically through spatial planning is described as ‘missing’ and ‘subordinate’ in national adaptation plans (Greiving and Fleischhauer, 2012),‘underrepresented’ (Roggema, et al., 2012)and ‘limited and disparate’ in planning literature (Davoudi, et al., 2009). Hurlimann and March (2012) suggest this may be due to limited experiences of adaptation in developed nations while Roggema et al. (2012) and Crane and Landis (2010) suggest it is because climate change is a wicked problem involving an unfamiliar problem, various frames of understanding and uncertain solutions. The potential for goal conflicts within this policy forum seem to outweigh the synergies. Yet, spatial planning will be a critical policy tool in the future to both protect and adapt communities to climate change.

Effects of air pollution exposure on adult bicycle commuters : an investigation of respiratory health, motorised traffic proximity and the utility of commute re-routing

Bicycle commuting has the potential to be an effective contributing solution to address some of modern society’s biggest issues, including cardiovascular disease, anthropogenic climate change and urban traffic congestion. However, individuals shifting from a passive to an active commute mode may be increasing their potential for air pollution exposure and the associated health risk. This project, consisting of three studies, was designed to investigate the health effects of bicycle commuters in relation to air pollution exposure, in a major city in Australia (Brisbane). The aims of the three studies were to: 1) examine the relationship of in-commute air pollution exposure perception, symptoms and risk management; 2) assess the efficacy of commute re-routing as a risk management strategy by determining the exposure potential profile of ultrafine particles along commute route alternatives of low and high proximity to motorised traffic; and, 3) evaluate the feasibility of implementing commute re-routing as a risk management strategy by monitoring ultrafine particle exposure and consequential physiological response from using commute route alternatives based on real-world circumstances; 3) investigate the potential of reducing exposure to ultrafine particles (UFP; < 0.1 µm) during bicycle commuting by lowering proximity to motorised traffic with real-time air pollution and acute inflammatory measurements in healthy individuals using their typical, and an alternative to their typical, bicycle commute route. The methods of the three studies included: 1) a questionnaire-based investigation with regular bicycle commuters in Brisbane, Australia. Participants (n = 153; age = 41 ± 11 yr; 28% female) reported the characteristics of their typical bicycle commute, along with exposure perception and acute respiratory symptoms, and amenability for using a respirator or re-routing their commute as risk management strategies; 2) inhaled particle counts measured along popular pre-identified bicycle commute route alterations of low (LOW) and high (HIGH) motorised traffic to the same inner-city destination at peak commute traffic times. During commute, real-time particle number concentration (PNC; mostly in the UFP range) and particle diameter (PD), heart and respiratory rate, geographical location, and meteorological variables were measured. To determine inhaled particle counts, ventilation rate was calculated from heart-rate-ventilation associations, produced from periodic exercise testing; 3) thirty-five healthy adults (mean ± SD: age = 39 ± 11 yr; 29% female) completed two return trips of their typical route (HIGH) and a pre-determined altered route of lower proximity to motorised traffic (LOW; determined by the proportion of on-road cycle paths). Particle number concentration (PNC) and diameter (PD) were monitored in real-time in-commute. Acute inflammatory indices of respiratory symptom incidence, lung function and spontaneous sputum (for inflammatory cell analyses) were collected immediately pre-commute, and one and three hours post-commute. The main results of the three studies are that: 1) healthy individuals reported a higher incidence of specific acute respiratory symptoms in- and post- (compared to pre-) commute (p < 0.05). The incidence of specific acute respiratory symptoms was significantly higher for participants with respiratory disorder history compared to healthy participants (p < 0.05). The incidence of in-commute offensive odour detection, and the perception of in-commute air pollution exposure, was significantly lower for participants with smoking history compared to healthy participants (p < 0.05). Females reported significantly higher incidence of in-commute air pollution exposure perception and other specific acute respiratory symptoms, and were more amenable to commute re-routing, compared to males (p < 0.05). Healthy individuals have indicated a higher incidence of acute respiratory symptoms in- and post- (compared to pre-) bicycle commuting, with female gender and respiratory disorder history indicating a comparably-higher susceptibility; 2) total mean PNC of LOW (compared to HIGH) was reduced (1.56 x e4 ± 0.38 x e4 versus 3.06 x e4 ± 0.53 x e4 ppcc; p = 0.012). Total estimated ventilation rate did not vary significantly between LOW and HIGH (43 ± 5 versus 46 ± 9 L•min; p = 0.136); however, due to total mean PNC, accumulated inhaled particle counts were 48% lower in LOW, compared to HIGH (7.6 x e8 ± 1.5 x e8 versus 14.6 x e8 ± 1.8 x e8; p = 0.003); 3) LOW resulted in a significant reduction in mean PNC (1.91 x e4 ± 0.93 x e4 ppcc vs. 2.95 x e4 ± 1.50 x e4 ppcc; p ≤ 0.001). Commute distance and duration were not significantly different between LOW and HIGH (12.8 ± 7.1 vs. 12.0 ± 6.9 km and 44 ± 17 vs. 42 ± 17 mins, respectively). Besides incidence of in-commute offensive odour detection (42 vs. 56 %; p = 0.019), incidence of dust and soot observation (33 vs. 47 %; p = 0.038) and nasopharyngeal irritation (31 vs. 41 %; p = 0.007), acute inflammatory indices were not significantly associated to in-commute PNC, nor were these indices reduced with LOW compared to HIGH. The main conclusions of the three studies are that: 1) the perception of air pollution exposure levels and the amenability to adopt exposure risk management strategies where applicable will aid the general population in shifting from passive, motorised transport modes to bicycle commuting; 2) for bicycle commuting at peak morning commute times, inhaled particle counts and therefore cardiopulmonary health risk may be substantially reduced by decreasing exposure to motorised traffic, which should be considered by both bicycle commuters and urban planners; 3) exposure to PNC, and the incidence of offensive odour and nasopharyngeal irritation, can be significantly reduced when utilising a strategy of lowering proximity to motorised traffic whilst bicycle commuting, without significantly increasing commute distance or duration, which may bring important benefits for both healthy and susceptible individuals. In summary, the findings from this project suggests that bicycle commuters can significantly lower their exposure to ultrafine particle emissions by varying their commute route to reduce proximity to motorised traffic and associated combustion emissions without necessarily affecting their time of commute. While the health endpoints assessed with healthy individuals were not indicative of acute health detriment, individuals with pre-disposing physiological-susceptibility may benefit considerably from this risk management strategy – a necessary research focus with the contemporary increased popularity of both promotion and participation in bicycle commuting.

Climate change adaptation for public buildings management : stakeholder roles and responsibilities

Climate change is expected to increase earth’s temperatures and consequently result in more frequent extreme weather events such as cyclones, storms, droughts and floods and rising global sea levels. This phenomenon will affect all assets. This paper discusses the impact of climate change and its consequences on public buildings. Public building management encompasses the building life cycle from planning, procurement, operation, repair and maintenance and building disposal. This paper recommends climate change adaptation strategies to be integrated into public building management. The roles and responsibilities of asset managers and users are discussed within the framework of planning and implementation of public building management and the integration of climate change adaptation strategies. A key point is that climate change can induce premature obsolescence of public buildings and services, which will increase the maintenance and refurbishment costs. This in turn will affect the life cycle cost of the building. Furthermore, a business continuity plan is essential for public building management in the context of disasters. The paper also highlights the significant role that the occupants of public buildings can play in the development and implementation of climate change adaptation strategies.

Monitoring the price and affordability of foods and diets globally

Food prices and food affordability are important determinants of food choices, obesity and non-communicable diseases. As governments around the world consider policies to promote the consumption of healthier foods, data on the relative price and affordability of foods, with a particular focus on the difference between ‘less healthy’ and ‘healthy’ foods and diets, are urgently needed. This paper briefly reviews past and current approaches to monitoring food prices, and identifies key issues affecting the development of practical tools and methods for food price data collection, analysis and reporting. A step-wise monitoring framework, including measurement indicators, is proposed. ‘Minimal’ data collection will assess the differential price of ‘healthy’ and ‘less healthy’ foods; ‘expanded’ monitoring will assess the differential price of ‘healthy’ and ‘less healthy’ diets; and the ‘optimal’ approach will also monitor food affordability, by taking into account household income. The monitoring of the price and affordability of ‘healthy’ and ‘less healthy’ foods and diets globally will provide robust data and benchmarks to inform economic and fiscal policy responses. Given the range of methodological, cultural and logistical challenges in this area, it is imperative that all aspects of the proposed monitoring framework are tested rigorously before implementation.

Monitoring policy and actions on food environments : rationale and outline of the INFORMAS policy engagement and communication strategies

The International Network for Food and Obesity/non-communicable diseases Research, Monitoring and Action Support (INFORMAS) proposes to collect performance indicators on food policies, actions and environments related to obesity and non-communicable diseases. This paper reviews existing communications strategies used for performance indicators and proposes the approach to be taken for INFORMAS. Twenty-seven scoring and rating tools were identified in various fields of public health including alcohol, tobacco, physical activity, infant feeding and food environments. These were compared based on the types of indicators used and how they were quantified, scoring methods, presentation and the communication and reporting strategies used. There are several implications of these analyses for INFORMAS: the ratings/benchmarking approach is very commonly used, presumably because it is an effective way to communicate progress and stimulate action, although this has not been formally evaluated; the tools used must be trustworthy, pragmatic and policy-relevant; multiple channels of communication will be needed; communications need to be tailored and targeted to decision-makers; data and methods should be freely accessible. The proposed communications strategy for INFORMAS has been built around these lessons to ensure that INFORMAS's outputs have the greatest chance of being used to improve food environments.

Monitoring food and non-alcoholic beverage promotions to children

Food and non-alcoholic beverage marketing is recognized as an important factor influencing food choices related to non-communicable diseases. The monitoring of populations' exposure to food and non-alcoholic beverage promotions, and the content of these promotions, is necessary to generate evidence to understand the extent of the problem, and to determine appropriate and effective policy responses. A review of studies measuring the nature and extent of exposure to food promotions was conducted to identify approaches to monitoring food promotions via dominant media platforms. A step-wise approach, comprising ‘minimal’, ‘expanded’ and ‘optimal’ monitoring activities, was designed. This approach can be used to assess the frequency and level of exposure of population groups (especially children) to food promotions, the persuasive power of techniques used in promotional communications (power of promotions) and the nutritional composition of promoted food products. Detailed procedures for data sampling, data collection and data analysis for a range of media types are presented, as well as quantifiable measurement indicators for assessing exposure to and power of food and non-alcoholic beverage promotions. The proposed framework supports the development of a consistent system for monitoring food and non-alcoholic beverage promotions for comparison between countries and over time.

Monitoring the health-related labelling of foods and non-alcoholic beverages in retail settings

Food labelling on food packaging has the potential to have both positive and negative effects on diets. Monitoring different aspects of food labelling would help to identify priority policy options to help people make healthier food choices. A taxonomy of the elements of health-related food labelling is proposed. A systematic review of studies that assessed the nature and extent of health-related food labelling has been conducted to identify approaches to monitoring food labelling. A step-wise approach has been developed for independently assessing the nature and extent of health-related food labelling in different countries and over time. Procedures for sampling the food supply, and collecting and analysing data are proposed, as well as quantifiable measurement indicators and benchmarks for health-related food labelling.