Comparação entre um trocador aniônico de sal de amônio quaternário de quitosana e um trocador comercial na extração de fósforo disponível em solos

The present work aimed modify chemically the chitosan (QTS) surface to obtain a reticulate chitosan quaternary ammonium salt (SAQQR), and compare this anionic exchanger with an commercial ion exchanger in the extraction of available phosphorus in soils. The results showed that the two exchangers are identical, extracting similar and proportional quantities of available phosphorus in the studied soils, and the anionic exchanger of SAQQR provides a high chemical stability, not affected by the pH difference of soils.

Influência da quantidade de amônio na síntese de nanopartículas de óxido de ferro por microemulsão

Iron oxide nanoparticles were synthesized in microemulsion systems composed by Triton X-100/hexyl alcohol/cyclohexane/aqueous solution. The nanoparticles were synthesized in microemulsions containing different amounts of ammonium, in order to evaluate the influence of this parameter on the size of the nanoparticles and on the phase transformation after heat treatment. Powder materials were obtained after centrifugation, washing and drying, and they were analyzed as synthesized and after heating at 350, 500 and 1000 °C. It was observed that the higher amount of ammonium induced smaller particles and minor phase transformation, possibly due to a preferential nucleation process.

Caracterização do material particulado fino e grosso e composição da fração inorgânica solúvel em água em São José dos Campos (SP)

Air samples of fine (PM2,5) and coarse (PM2,5-10) particulate matter were collected in São José dos Campos from February 2004 to February 2005. Average PM10 mass concentrations was 31.2 ± 14.0 μg m-3, half of which belonging to the PM2.5 fraction. Ammonium and SO4(2-) were predominantly found in the fine fraction. Average (NH4)2SO4 concentration was estimated to be about 2.9 μg m-3. Chloride, Na+ and NO3- were mostly associated with PM2,5-10. Chloride deficits with respect to sea-salt Cl/Na ratio were found in both size fractions.

Avaliação da liberação de NH4NO3 ocluido em zeólita 4A a partir de soluções salinas

The zeolite 4A was used to evaluate the thermo kinetics parameters of NH4+ and NO3- ions occluded in its structure. The Osawa method for activation energy calculation was used to evaluate its thermal stability, and the results shown that the ion species interact differently depending on the zeolite pores, which determines the controlled release by its structure.

Purificação e caracterização da quitinase de uva (Vitis vinífera L. cv Red Globe) para a produção de quitosana a partir de quitina de camarão

Chitinase is produced by a wide variety of plants as a defense against peste attacks. In this study, grape chitinases were purified 16 times by fractionation in 80% ammonium sulfate followed by dialysis and filtration. Purified chitinases exhibited enzymatic activity toward chitin azure. The yield of purified chitinase was 229 mg/L with chitinase activity of 563 U/g. Chitinases had molecular masses of 24 and 30 kDa, as evaluated by SDS-PAGE 12.5%. Two pH optima were determined 3.0 and 6.0. The optimal temperature was 42 °C. Pre hydrolysis of crystalline shrimp chitin by chitinases caused in an increase in the deacetylation ratio triggered by chitin deacetylase producing chitooligosaccharides with DA (degree acetylation) of 58.8%.

In situ synthesis of nanoclay filled polyethylene using polymer supported metallocene catalyst system

In situ ethylene polymerizations were performed using bis(cyclopentadiene)titanium dichloride supported on polyethersulfone as catalyst. The bis(cyclopentadiene)titanium dichloride supported on polyethersulfone catalyst activity estimated by ethylene polymerization was 360 kgPE/molTi/h. During polymerization the fillers used were montmorillionite nanoclays having surface modifications with 35-45 wt% dimethyl dialkyl(14-18)amine (FA) and 25-30 wt% trimethyl stearyl ammonium (FB). These fillers were pretreated with methylaluminoxine (MAO; cocatalyst) for better dispersion onto the polymer matrix. The formation of polyethylene within the whole matrix was confirmed by FTIR studies. It was found that the nature of nanofiller did not have any remarkable effect on the melting characteristics of the polymer. TGA study indicates that nanoclay FB filled polyethylene has higher thermal stability than nanoclay FA filled polyethylene. The melting temperature of the obtained polyethylenes was 142 ºC, which corresponds to that synthesized by the polyether sulfone supported catalyst.

Estudo da emissão por fluorescência de ultravioleta na quantificação de um inibidor de corrosão do tipo sal de amônio quaternário em água

Quaternary ammonium salts are the corrosion inhibitors most frequently used by the oil industry. In this study, the ultraviolet fluorescence technique was evaluated for the analysis of a quaternary ammonium salt in water as a corrosion inhibitor. The comparison with standard salt showed that an alkyl aryl quaternary ammonium salt is the main fluorophore, with emission maxima at 306 and 593 nm. The best instrumental parameters were: width of excitation and emission slits of 10 and 15 nm, respectively, and scan rate of 10 nm min-1. The presence of aromatic compounds and biocides affects the analysis of corrosion inhibitors.

Montmorilonita modificada como catalisador heterogêneo em reações de esterificação (m)etílica de ácido láurico

ABSTRACT Montmorillonite was modified with zirconium polyoxycations in the presence of ammonium sulphate. The material was characterized and used as a catalyst in the esterification of lauric acid, the reactions being accompanied by 2³ factorial design. Conversions of up to 95.33 and 83.35% were observed for the methyl and ethyl esterification reactions respectively, proving superior to results obtained by thermal conversion. The material was submitted to three reaction cycles and similar conversions were observed, indicating the catalyst is not significantly deactivated after reuse. The catalyst was also tested under reflux conditions, yielding a maximum conversion of 36.86%.

Isolamento do tungstênio da volframita da mina de Igarapé Manteiga (Rondônia - Brasil) por lixiviação ácida

We report results of the efficiency of tungsten extraction from wolframite concentrate (containing 61.5 wt % WO3) from the Igarapé Manteiga mine (state of Rondônia, Brazil) through acid leaching with strong mineral acids at 100 ºC and 400 rpm for 2-4 h. HCl yielded insoluble matter containing the highest WO3 content (90 wt %). This solid was dissolved in concentrated NH3(aq) at 25 ºC and the insoluble matter filtrated. The filtrate was slowly evaporated. 70 wt % of the tungsten present in the starting concentrate material was recovered as ammonium paratungstate (APT).

Processing of spent NiW/Al2O3 catalysts

Spent oxidized (500 ºC, 5 h) commercial NiW/Al2O3 catalysts were processed using two different routes: a) fusion with NaOH (650 ºC, 1 h), the roasted mass was leached in water; b) leaching with HCl or H2SO4 (70 ºC, 1-3 h). HCl was the best leachant. In both routes, soluble tungsten was extracted at pH 1 with Alamine 336 (10 vol.% in kerosene) and stripped with 2 mol L-1 NH4OH (25 ºC, one stage, aqueous/organic ratio = 1 v/v). Tungsten was isolated as ammonium paratungstate at very high yield (> 97.5%). The elements were better separated using the acidic route.

Desenvolvimento de um método analítico baseado em microextração líquido-líquido para a determinação de cromo (VI) em amostras aquosas com detecção por espectrometria de absorção atômica em chama

In this study, a method for determination of hexavalent chromium in aqueous samples using liquid-liquid microextraction (LLME) and detection by Flame Atomic Absorption Spectrometry (F AAS) was developed. The LLME procedure was based on the extraction of Cr (VI) by acetone at a sample pH of 1.2. The use of saturated ammonium sulphate solution allowed effective separation of the aqueous and organic phases and acetone extracted chromium. The sample pH, acetone volume and stirring time were optimized by a full factorial design.

Produção de biossurfactantes por microrganismos isolados de solo contaminado com óleo diesel

The aim of this work was to produce biosurfactants through submerged fermentation using microorganisms isolated from soil contaminated with diesel. Microorganisms were isolated, characterized by the production of biosurfactants, and used to study the influence of type, induction and concentration of ammonium sulfate as a nitrogen source in the culture medium. The microorganisms that showed best results, in terms of production of biosurfactants, were identified as being of the genus Pseudomonas and Bacillus. The biosurfactants produced proved capable of reducing the surface tension of the media to 39 mN/m and 34 mN/m, respectively. Higher biosurfactant production was obtained in the medium containing 1% soybean oil without ammonium sulfate.

Emissões de óxido nitroso do tanque de aeração de uma estação de tratamento de esgotos com sistema de lodos ativados convencional

Nitrous oxide (N2O) emissions were measured monthly from January to June 2010 in the aeration tank of a wastewater treatment plant (WWTP) in Southeast Brazil. Emissions were lower in summer than winter and were positively related with influent ammonium (NH4+) concentration. The average N2O emission was 1.11 kg N day-1 corresponding to 0.02% of the influent total nitrogen load. The average emission factor calculated for the population served was 2.5 lower than that proposed by the Intergovernmental Panel on Climate Change (IPCC) for inventories of N2O emissions from WWTPs with controlled nitrification and denitrification processes.

Acúmulo de cargas elétricas em propelente sólido compósito com matriz de polibutadieno líquido hidroxilado

Composite solid propellants prepared with HTPB prepolymer - Hydroxyl Terminated Polybutadiene, AP - Ammonium Perchlorate as oxidizer and aluminum particles as an additive metal, have characteristics of high electrical resistivity. The loading process of the polymer matrix did not obtain homogeneity, resulting in clusters, mainly of metal particles. The effect of clustering in the composite was studied and observed experimentally, and this effect was one of the factors explaining the phenomenon of electrical charging of the composite. This electrical potential, when discharged abruptly, can generate an electric spark with sufficient energy for sustained ignition of a solid rocket motor.

Desenvolvimento de um método para a determinação de tioconazol associado a nanocápsulas poliméricas por cromatografia líquida

The aim of this work was to develop and validate an analytical method for the quantification of tioconazole in polymeric nanocapsule suspensions by high performance liquid chromatography with UV detection. The analysis was performed with a mobile phase composed of methanol:water (80:20) and 0.18% ammonium hydroxide; RP-18 column and UV detection at 219 nm. The method proved to be linear in the concentration range of 5-50 µg mL-1 (r = 0.9999), specific, precise (repeatability RSD = 1.42%, intermediate precision RSD = 1.17%), accurate (98 - 102%) and robust (RSD < 2.0%). In conclusion, a simple and rapid method was validated proving suitable for quantification of tioconazole in polymeric nanocapsules.