Agent-based modelling of worker interactions and related impacts on workplace dynamics

This study uses agent based modelling to simulate the worker interactions within a workplace and to investigate how the interactions can have impact on the workplace dynamics. Two new models (Bounded Confidence with Bias model and Relative Agreement with Bias model) are built based on the theoretical foundation of two existing models. A new factor, namely bias, is added into the new models which raises several issues to be studied.

Modeling of dynamic material behavior in hot deformation: Forging of Ti-6242

A new method of modeling material behavior which accounts for the dynamic metallurgical processes occurring during hot deformation is presented. The approach in this method is to consider the workpiece as a dissipator of power in the total processing system and to evaluate the dissipated power co-contentJ = ∫o σ ε ⋅dσ from the constitutive equation relating the strain rate (ε) to the flow stress (σ). The optimum processing conditions of temperature and strain rate are those corresponding to the maximum or peak inJ. It is shown thatJ is related to the strain-rate sensitivity (m) of the material and reaches a maximum value(J max) whenm = 1. The efficiency of the power dissipation(J/J max) through metallurgical processes is shown to be an index of the dynamic behavior of the material and is useful in obtaining a unique combination of temperature and strain rate for processing and also in delineating the regions of internal fracture. In this method of modeling, noa priori knowledge or evaluation of the atomistic mechanisms is required, and the method is effective even when more than one dissipation process occurs, which is particularly advantageous in the hot processing of commercial alloys having complex microstructures. This method has been applied to modeling of the behavior of Ti-6242 during hot forging. The behavior of α+ β andβ preform microstructures has been exam-ined, and the results show that the optimum condition for hot forging of these preforms is obtained at 927 °C (1200 K) and a strain rate of 1CT•3 s•1. Variations in the efficiency of dissipation with temperature and strain rate are correlated with the dynamic microstructural changes occurring in the material.

Focused Prefetching: Performance Oriented Prefetching Based On Commit Stalls

Loads that miss in L1 or L2 caches and waiting for their data at the head of the ROB cause significant slow down in the form of commit stalls. We identify that most of these commit stalls are caused by a small set of loads, referred to as LIMCOS (Loads Incurring Majority of COmmit Stalls). We propose simple history-based classifiers that track commit stalls suffered by loads to help us identify this small set of loads. We study an application of these classifiers to prefetching. The classifiers are used to train the prefetcher to focus on the misses suffered by LIMCOS. This, referred to as focused prefetching, results in a 9.8% gain in IPC over naive GHB based delta correlation prefetcher along with a 20.3% reduction in memory traffic for a set of 17 memory-intensive SPEC2000 benchmarks. Another important impact of focused prefetching is a 61% improvement in the accuracy of prefetches. We demonstrate that the proposed classification criterion performs better than other existing criteria like criticality and delinquent loads. Also we show that the criterion of focusing on commit stalls is robust enough across cache levels and can be applied to any prefetcher without any modifications to the prefetcher.

A large orthotropic plate with misfit pin under arbitrarily oriented biaxial loading

The problem of misfit (interference or clearance) pin in a large orthotropic plate was solved earlier by the authors for biaxial loading in the principal directions of orthotropy. Here, a more general case of arbitrarily oriented loading is considered. The most important aspect of the problem studied is the partial contact at the pin-hole interface. The solution is obtained by extending the use of ‘inverse technique’ which was successfully applied earlier by the authors to problems of pins in isotropic and orthotropic domains. The loss of symmetry because of the arbitrary orientation of loading makes the problem more complex. Additional parameters are then involved in the inversion of the problem for the solution. Numerical results are presented primarily for a smooth interference fit pin in a typical orthotropic plate.

Damage potential of an introduced biological control agent Agonosoma trilineatum (F.) on bellyache bush (Jatropha gossypiifolia L.)

The seed-feeding jewel bug, Agonosoma trilineatum (F.), is an introduced biological control agent for bellyache bush, Jatropha gossypiifolia L. To quantify the damage potential of this agent, shadehouse experiments were conducted with individual bellyache bush plants exposed to a range of jewel bug densities (0, 6 or 24 jewel bugs/plant). The level of abortion of both immature and mature seed capsules and impacts on seed weight and seed viability were recorded in an initial short-term study. The ability of the jewel bug to survive and cause sustained damage was then investigated by measuring seed production, the survival of adults and nymph density across three 6-month cycles. The level of seed capsule abortion caused by the jewel bug was significantly affected by the maturity status of capsules and the density of insects present. Immature capsules were most susceptible and capsule abortion increased with jewel bug density. Similarly, on average, the insects reduced the viability of bellyache bush seeds by 79% and 89% at low and high densities, respectively. However, sustaining jewel bug populations for prolonged periods proved difficult. Adult survival at the end of three 6-month cycles averaged 11% and associated reductions in viable seed production ranged between 55% and 77%. These results suggest that the jewel bug has the potential to reduce the number of viable seeds entering the soil seed bank provided populations can be established and maintained at sufficiently high densities.

On an analytical-numerical procedure for the analysis of cylindrical shells with arbitrarily oriented cracks

An analytical-numerical procedure for obtaining stress intensity factor solutions for an arbitrarily oriented crack in a long, thin circular cylindrical shell is presented. The method of analysis involves obtaining a series solution to the governing shell equation in terms of Mathieu and modified Mathieu functions by the method of separation of variables and satisfying the crack surface boundary conditions numerically using collocation. The solution is then transformed from elliptic coordinates to polar coordinates with crack tip as the origin through a Taylor series expansion and membrane and bending stress intensity factors are computed. Numerical results are presented and discussed for the pressure loading case.

Phylogenetic considerations for predicting the host range of Ustilago sporoboli-indici, a potential biological control agent for Sporobolus species in Australia

The ribosomal DNA internal transcribed spacer region was amplified and sequenced from a selection of specimens of the Sporobolus smut Ustilago sporoboli-indici. Phylogenetic comparison with other Ustilago and Sporisorium species revealed strong support for an evolutionary radiation of Ustilago species infecting the Chloridoideae and Pooideae, of which U. sporoboli-indici forms a major lineage. Comparisons are made with other groups of plant pathogenic fungi, and it is concluded that phylogenetic analyses of potential biocontrol agents are useful for identifying pathogens that are derived from evolutionary lineages that parasitize a wide range of unrelated plants. Such pathogens are less desirable as biocontrol agents as they may have a greater likelihood of infecting plants outside their normal host ranges.

Utilizing the assassin bug, Pristhesancus plagipennis (Hemiptera: Reduviidae), as a biological control agent within an integrated pest management programme for Helicoverpa spp. (Lepidoptera: Noctuidae) and Creontiades spp. (Hemiptera: Miridae) in cotton

Helicoverpa spp. and mirids, Creontiades spp., have been difficult to control biologically in cotton due to their unpredictable temporal abundance combined with a cropping environment often made hostile by frequent usage of broad spectrum insecticides. To address this problem, a range of new generation insecticides registered for use in cotton were tested for compatibility with the assassin bug, Pristhesancus plagipennis (Walker), a potential biological control agent for Helicoverpa spp. and Creontiades spp. Indoxacarb, pyriproxifen, buprofezin, spinosad and fipronil were found to be of low to moderate toxicity on P. plagipennis whilst emamectin benzoate, abamectin, diafenthiuron, imidacloprid and omethaote were moderate to highly toxic. Inundative releases of P. plagipennis integrated with insecticides identified as being of low toxicity were then tested and compared with treatments of P. plagipennis and the compatible insecticides used alone, conventionally sprayed usage practice and an untreated control during two field experiments in cotton. The biological control provided by P. plagipennis nymphs when combined with compatible insecticides provided significant (P<0.001) reductions in Helicoverpa and Creontiades spp. on cotton and provided equivalent yields to conventionally sprayed cotton with half of the synthetic insecticide input. Despite this, the utilization of P. plagipennis in cotton as part of an integrated pest management programme remains unlikely due to high inundative release costs relative to other control technologies such as insecticides and transgenic (Bt) cotton varieties.

Modeling chickpea growth and development: Nitrogen accumulation and use

Quantitative information regarding nitrogen (N) accumulation and its distribution to leaves, stems and grains under varying environmental and growth conditions are limited for chickpea (Cicer arietinum L.). The information is required for the development of crop growth models and also for assessment of the contribution of chickpea to N balances in cropping systems. Accordingly, these processes were quantified in chickpea under different environmental and growth conditions (still without water or N deficit) using four field experiments and 1325 N measurements. N concentration ([N]) in green leaves was 50 mg g-1 up to beginning of seed growth, and then it declined linearly to 30 mg g-1 at the end of seed growth phase. [N] in senesced leaves was 12 mg g-1. Stem [N] decreased from 30 mg g-1 early in the season to 8 mg g-1 in senesced stems at maturity. Pod [N] was constant (35 mg g-1), but grain [N] decreased from 60 mg g-1 early in seed growth to 43 mg g-1 at maturity. Total N accumulation ranged between 9 and 30 g m-2. N accumulation was closely linked to biomass accumulation until maturity. N accumulation efficiency (N accumulation relative to biomass accumulation) was 0.033 g g-1 where total biomass was -2 and during early growth period, but it decreased to 0.0176 g g-1 during the later growth period when total biomass was >218 g m-2. During vegetative growth (up to first-pod), 58% of N was partitioned to leaves and 42% to stems. Depending on growth conditions, 37-72% of leaf N and 12-56% of stem N was remobilized to the grains. The parameter estimates and functions obtained in this study can be used in chickpea simulation models to simulate N accumulation and distribution.

Modeling growth of hydrogen bubbles in aluminum castings using the level-set method

A new approach is proposed to solve for the growth as well as the movement of hydrogen bubbles during solidification in aluminum castings. A level-set methodology has been adopted to handle this multiphase phenomenon. A microscale domain is considered and the growth and movement of hydrogen bubbles in this domain has been studied. The growth characteristics of hydrogen bubbles have been evaluated under free growth conditions in a melt having a hydrogen input caused b solidification occurring around the microdomain.

Pest management in Queensland strawberries: Reality bites, and growers' perspectives change!

Prior to the 1980s, arthropod pest control in Queensland strawberries was based entirely on calendar sprays of insecticides (mainly endosulfan, triclorfon, dimethoate and carbaryl) and a miticide (dicofol). These chemicals were applied frequently and spider mite outbreaks occurred every season. The concept of integrated pest management (IPM) had not been introduced to growers, and the suggestion that an alternative to the standard chemical pest control recipe might be available, was ignored. Circumstances changed when the predatory mite, Phytoseiulus persimilis Athios-Henriot, became available commercially in Australia, providing the opportunity to manage spider mites, the major pests of strawberries, with an effective biological agent. Trials conducted on commercial farms in the early 1980s indicated that a revolution in strawberry pest management was at hand, but the industry generally remained sceptical and afraid to adopt the new strategy. Lessons are learnt from disasters and the consequent monetary loss that ensues, and in 1993, such an event relating to ineffective spider mite control, spawned the revolution we had to have. Farm-oriented research and evolving grower perspectives have resulted in the acceptance of biological control of spider mites using Phytoseiulus persimilis and the 'pest in first' technique, and it now forms the basis of an IPM system that is used on more than 80% of the Queensland strawberry crop.

Constitutive modeling of shape memory alloy wire with non-local rate kinetics

A constitutive modeling approach for shape memory alloy (SMA) wire by taking into account the microstructural phase inhomogeneity and the associated solid-solid phase transformation kinetics is reported in this paper. The approach is applicable to general thermomechanical loading. Characterization of various scales in the non-local rate sensitive kinetics is the main focus of this paper. Design of SMA materials and actuators not only involve an optimal exploitation of the hysteresis loops during loading-unloading, but also accounts for fatigue and training cycle identifications. For a successful design of SMA integrated actuator systems, it is essential to include the microstructural inhomogeneity effects and the loading rate dependence of the martensitic evolution, since these factors play predominant role in fatigue. In the proposed formulation, the evolution of new phase is assumed according to Weibull distribution. Fourier transformation and finite difference methods are applied to arrive at the analytical form of two important scaling parameters. The ratio of these scaling parameters is of the order of 10(6) for stress-free temperature-induced transformation and 10(4) for stress-induced transformation. These scaling parameters are used in order to study the effect of microstructural variation on the thermo-mechanical force and interface driving force. It is observed that the interface driving force is significant during the evolution. Increase in the slopes of the transformation start and end regions in the stress-strain hysteresis loop is observed for mechanical loading with higher rates.

Topochemical photodimerization of 7-acetoxycoumarin: the acetoxy group as a steering agent

Among the various substituted coumarins investigated only 7-acetoxycoumarin is observed to photodimerize topochemically in the crystalline state and this observation may be of importance in the context of "crystal engineering".

Expert Identity in Development of Core-Task-Oriented Working Practices for Mastering Demanding Situations

The point of departure in this dissertation was the practical safety problem of unanticipated, unfamiliar events and unexpected changes in the environment, the demanding situations which the operators should take care of in the complex socio-technical systems. The aim of this thesis was to increase the understanding of demanding situations and of the resources for coping with these situations by presenting a new construct, a conceptual model called Expert Identity (ExId) as a way to open up new solutions to the problem of demanding situations and by testing the model in empirical studies on operator work. The premises of the Core-Task Analysis (CTA) framework were adopted as a starting point: core-task oriented working practices promote the system efficiency (incl. safety, productivity and well-being targets) and that should be supported. The negative effects of stress were summarised and the possible countermeasures related to the operators' personal resources such as experience, expertise, sense of control, conceptions of work and self etc. were considered. ExId was proposed as a way to bring emotional-energetic depth into the work analysis and to supplement CTA-based practical methods to discover development challenges and to contribute to the development of complex socio-technical systems. The potential of ExId to promote understanding of operator work was demonstrated in the context of the six empirical studies on operator work. Each of these studies had its own practical objectives within the corresponding quite broad focuses of the studies. The concluding research questions were: 1) Are the assumptions made in ExId on the basis of the different theories and previous studies supported by the empirical findings? 2) Does the ExId construct promote understanding of the operator work in empirical studies? 3) What are the strengths and weaknesses of the ExId construct? The layers and the assumptions of the development of expert identity appeared to gain evidence. The new conceptual model worked as a part of an analysis of different kinds of data, as a part of different methods used for different purposes, in different work contexts. The results showed that the operators had problems in taking care of the core task resulting from the discrepancy between the demands and resources (either personal or external). The changes of work, the difficulties in reaching the real content of work in the organisation and the limits of the practical means of support had complicated the problem and limited the possibilities of the development actions within the case organisations. Personal resources seemed to be sensitive to the changes, adaptation is taking place, but not deeply or quickly enough. Furthermore, the results showed several characteristics of the studied contexts that complicated the operators' possibilities to grow into or with the demands and to develop practices, expertise and expert identity matching the core task. They were: discontinuation of the work demands, discrepancy between conceptions of work held in the other parts of organisation, visions and the reality faced by the operators, emphasis on the individual efforts and situational solutions. The potential of ExId to open up new paths to solving the problem of the demanding situations and its ability to enable studies on practices in the field was considered in the discussion. The results were interpreted as promising enough to encourage the conduction of further studies on ExId. This dissertation proposes especially contribution to supporting the workers in recognising the changing demands and their possibilities for growing with them when aiming to support human performance in complex socio-technical systems, both in designing the systems and solving the existing problems.