Development and Analysis of a Novel Isosceles Trapezoidal Dielectric Resonator Antenna For Wireless Communication

This thesis describes the development and analysis of an Isosceles Trapezoidal Dielectric Resonator Antenna (ITDRA) by realizing different DR orientations with suitable feed configurations enabling it to be used as multiband, dual band dual polarized and wideband applications. The motivation for this work has been inspired by the need for compact, high efficient, low cost antenna suitable for multi band application, dual band dual polarized operation and broadband operation with the possibility of using with MICs, and to ensure less expensive, more efficient and quality wireless communication systems. To satisfy these challenging demands a novel shaped Dielectric Resonator (DR) is fabricated and investigated for the possibility of above required properties by trying out different orientations of the DR on a simple microstrip feed and with slotted ground plane as well. The thesis initially discusses and evaluates recent and past developments taken place within the microwave industry on this topic through a concise review of literature. Then the theoretical aspects of DRA and different feeding techniques are described. Following this, fabrication and characterization of DRA is explained. To achieve the desired requirements as above both simulations and experimental measurements were undertaken. A 3-D finite element method (FEM) electromagnetic simulation tool, HFSSTM by Agilent, is used to determine the optimum geometry of the dielectric resonator. It was found to be useful in producing approximate results although it had some limitations. A numerical analysis technique, finite difference time domain (FDTD) is used for validating the results of wide band design at the end. MATLAB is used for modeling the ITDR and implementing FDTD analysis. In conclusion this work offers a new, efficient and relatively simple alternative for antennas to be used for multiple requirements in the wireless communication system.

Communication Parameters in the Marine Fisheries Sector of Kerala-A Study of Kollam Coastal Villages

Department of Applied Economics,Cochin University of Science and Technology

Effect of Gender-role Orientations and Communication Styles on Executive Performance

Biosocial profile can produce variations in Gender-role Orientation of executives. Biosocial variables are not responsible for the development of Communication Style except in cases of number of children, dual career family and fathers occupation. Gender-role orientation is a function of Communication Style. Executive performance is a function of Communication Style.Gender- role orientation can have a decisive influence on executive performance. The cumulative effect of Communication Style and gender role orientation can produce variations in executive performance. Open Communication Style is predominantly responsible for the creation of a higher level executive performance than other Communication Styles.

Re-engineering and Re-defining University Libraries in the context of modern Information and Communication Technologies: a study with special reference to the University Libraries in Kerala

Information and communication technologies are the tools that underpin the emerging “Knowledge Society”. Exchange of information or knowledge between people and through networks of people has always taken place. But the ICT has radically changed the magnitude of this exchange, and thus factors such as timeliness of information and information dissemination patterns have become more important than ever.Since information and knowledge are so vital for the all round human development, libraries and institutions that manage these resources are indeed invaluable. So, the Library and Information Centres have a key role in the acquisition, processing, preservation and dissemination of information and knowledge. ln the modern context, library is providing service based on different types of documents such as manuscripts, printed, digital, etc. At the same time, acquisition, access, process, service etc. of these resources have become complicated now than ever before. The lCT made instrumental to extend libraries beyond the physical walls of a building and providing assistance in navigating and analyzing tremendous amounts of knowledge with a variety of digital tools. Thus, modern libraries are increasingly being re-defined as places to get unrestricted access to information in many formats and from many sources.The research was conducted in the university libraries in Kerala State, India. lt was identified that even though the information resources are flooding world over and several technologies have emerged to manage the situation for providing effective services to its clientele, most of the university libraries in Kerala were unable to exploit these technologies at maximum level. Though the libraries have automated many of their functions, wide gap prevails between the possible services and provided services. There are many good examples world over in the application of lCTs in libraries for the maximization of services and many such libraries have adopted the principles of reengineering and re-defining as a management strategy. Hence this study was targeted to look into how effectively adopted the modern lCTs in our libraries for maximizing the efficiency of operations and services and whether the principles of re-engineering and- redefining can be applied towards this.Data‘ was collected from library users, viz; student as well as faculty users; library ,professionals and university librarians, using structured questionnaires. This has been .supplemented by-observation of working of the libraries, discussions and interviews with the different types of users and staff, review of literature, etc. Personal observation of the organization set up, management practices, functions, facilities, resources, utilization of information resources and facilities by the users, etc. of the university libraries in Kerala have been made. Statistical techniques like percentage, mean, weighted mean, standard deviation, correlation, trend analysis, etc. have been used to analyse data.All the libraries could exploit only a very few possibilities of modern lCTs and hence they could not achieve effective Universal Bibliographic Control and desired efficiency and effectiveness in services. Because of this, the users as well as professionals are dissatisfied. Functional effectiveness in acquisition, access and process of information resources in various formats, development and maintenance of OPAC and WebOPAC, digital document delivery to remote users, Web based clearing of library counter services and resources, development of full-text databases, digital libraries and institutional repositories, consortia based operations for e-journals and databases, user education and information literacy, professional development with stress on lCTs, network administration and website maintenance, marketing of information, etc. are major areas need special attention to improve the situation. Finance, knowledge level on ICTs among library staff, professional dynamism and leadership, vision and support of the administrators and policy makers, prevailing educational set up and social environment in the state, etc. are some of the major hurdles in reaping the maximum possibilities of lCTs by the university libraries in Kerala. The principles of Business Process Re-engineering are found suitable to effectively apply to re-structure and redefine the operations and service system of the libraries. Most of the conventional departments or divisions prevailing in the university libraries were functioning as watertight compartments and their existing management system was more rigid to adopt the principles of change management. Hence, a thorough re-structuring of the divisions was indicated. Consortia based activities and pooling and sharing of information resources was advocated to meet the varied needs of the users in the main campuses and off campuses of the universities, affiliated colleges and remote stations. A uniform staff policy similar to that prevailing in CSIR, DRDO, ISRO, etc. has been proposed by the study not only in the university libraries in kerala but for the entire country.Restructuring of Lis education,integrated and Planned development of school,college,research and public library systems,etc.were also justified for reaping maximum benefits of the modern ICTs.

Acoustic radiation and scattering from cylindrical bodies and analysis of transducer arrays

New mathematical methods to analytically investigate linear acoustic radiation and scattering from cylindrical bodies and transducer arrays are presented. Three problems of interest involving cylinders in an infinite fluid are studied. In all the three problems, the Helmholtz equation is used to model propagation through the fluid and the beam patterns of arrays of transducers are studied. In the first problem, a method is presented to determine the omni-directional and directional far-field pressures radiated by a cylindrical transducer array in an infinite rigid cylindrical baffle. The solution to the Helmholtz equation and the displacement continuity condition at the interface between the array and the surrounding water are used to determine the pressure. The displacement of the surface of each transducer is in the direction of the normal to the array and is assumed to be uniform. Expressions are derived for the pressure radiated by a sector of the array vibrating in-phase, the entire array vibrating in-phase, and a sector of the array phase-shaded to simulate radiation from a rectangular piston. It is shown that the uniform displacement required for generating a source level of 220 dB ref. μPa @ 1m that is omni directional in the azimuthal plane is in the order of 1 micron for typical arrays. Numerical results are presented to show that there is only a small difference between the on-axis pressures radiated by phased cylindrical arrays and planar arrays. The problem is of interest because cylindrical arrays of projectors are often used to search for underwater objects. In the second problem, the errors, when using data-independent, classical, energy and split beam correlation methods, in finding the direction of arrival (DOA) of a plane acoustic wave, caused by the presence of a solid circular elastic cylindrical stiffener near a linear array of hydrophones, are investigated. Scattering from the effectively infinite cylinder is modeled using the exact axisymmetric equations of motion and the total pressures at the hydrophone locations are computed. The effect of the radius of the cylinder, a, the distance between the cylinder and the array, b, the number of hydrophones in the array, 2H, and the angle of incidence of the wave, α, on the error in finding the DOA are illustrated using numerical results. For an array that is about 30 times the wavelength and for small angles of incidence (α<10), the error in finding the DOA using the energy method is less than that using the split beam correlation method with beam steered to α; and in some cases, the error increases when b increases; and the errors in finding the DOA using the energy method and the split beam correlation method with beam steered to α vary approximately as a7 / 4 . The problem is of interest because elastic stiffeners – in nearly acoustically transparent sonar domes that are used to protect arrays of transducers – scatter waves that are incident on it and cause an error in the estimated direction of arrival of the wave. In the third problem, a high-frequency ray-acoustics method is presented and used to determine the interior pressure field when a plane wave is normally incident on a fluid cylinder embedded in another infinite fluid. The pressure field is determined by using geometrical and physical acoustics. The interior pressure is expressed as the sum of the pressures due to all rays that pass through a point. Numerical results are presented for ka = 20 to 100 where k is the acoustic wavenumber of the exterior fluid and a is the radius of the cylinder. The results are in good agreement with those obtained using field theory. The directional responses, to the plane wave, of sectors of a circular array of uniformly distributed hydrophones in the embedded cylinder are then computed. The sectors are used to simulate linear arrays with uniformly distributed normals by using delays. The directional responses are compared with the output from an array in an infinite homogenous fluid. These outputs are of interest as they are used to determine the direction of arrival of the plane wave. Numerical results are presented for a circular array with 32 hydrophones and 12 hydrophones in each sector. The problem is of interest because arrays of hydrophones are housed inside sonar domes and acoustic plane waves from distant sources are scattered by the dome filled with fresh water and cause deterioration in the performance of the array.

Service quality and reliability assessment of mobile communication infrastructure

The service quality of any sector has two major aspects namely technical and functional. Technical quality can be attained by maintaining technical specification as decided by the organization. Functional quality refers to the manner which service is delivered to customer which can be assessed by the customer feed backs. A field survey was conducted based on the management tool SERVQUAL, by designing 28 constructs under 7 dimensions of service quality. Stratified sampling techniques were used to get 336 valid responses and the gap scores of expectations and perceptions are analyzed using statistical techniques to identify the weakest dimension. To assess the technical aspects of availability six months live outage data of base transceiver were collected. The statistical and exploratory techniques were used to model the network performance. The failure patterns have been modeled in competing risk models and probability distribution of service outage and restorations were parameterized. Since the availability of network is a function of the reliability and maintainability of the network elements, any service provider who wishes to keep up their service level agreements on availability should be aware of the variability of these elements and its effects on interactions. The availability variations were studied by designing a discrete time event simulation model with probabilistic input parameters. The probabilistic distribution parameters arrived from live data analysis was used to design experiments to define the availability domain of the network under consideration. The availability domain can be used as a reference for planning and implementing maintenance activities. A new metric is proposed which incorporates a consistency index along with key service parameters that can be used to compare the performance of different service providers. The developed tool can be used for reliability analysis of mobile communication systems and assumes greater significance in the wake of mobile portability facility. It is also possible to have a relative measure of the effectiveness of different service providers.

Studies on underwater propagation development of programmable arrays

The thesis presented here includes the designing of underwater transducer arrays, taking into account the ‘interaction effects’ [30] among the closely packed radiators. Methods of minimizing the ‘interaction effects‘ by modifying the radiating aperture, are investigated. The need for this study arises as it is one of the important peculiar limitations that stands in the way of achieving maximum range of transmission of acoustic signals. Application of the modified array format for the generation of narrow beam low frequency sound waves, through nonlinear interactions, is discussed. Other techniques that can be advantageously exploited in array synthesis are also investigated

Studies on rubber compositions as passive acoustic materials in underwater electro acoustic transducer technology-and their aging characteristics

Rubber has become an indispensable material in Ocean technology. Rubber components play critical roles such as sealing, damping, environmental protection, electrical insulation etc. in most under water engineering applications. Technology driven innovations in electro acoustic transducers and other sophisticated end uses have enabled quantum jump in the quality and reliability of rubber components. Under water electro acoustic transducers use rubbers as a critical material in their construction. Work in this field has lead to highly reliable and high performance materials which has enhanced service life of transducers to the extent of 1015 years. Present work concentrates on these materials. Conventional rubbers are inadequate to meet many of the stringent functional of the requirements. There exists large gap of information in the rubber technology of under water rubbers, particularly in the context of under water electro acoustic transducers. Present study is towards filling up the gaps of information in this crucial area. The research work has been in the area of compounding and characterisation of rubbers for use in under water electro acoustic transducers. The study also covers specific material system such as encapsulation material, baffle material, seal material, etc. Life prediction techniques of under water rubbers in general has been established with reference to more than one functional property. This thesis is divided into 6 chapters.

RRNS-convolutional encoded concatenated code for OFDM based wireless communication

The modern telecommunication industry demands higher capacity networks with high data rate. Orthogonal frequency division multiplexing (OFDM) is a promising technique for high data rate wireless communications at reasonable complexity in wireless channels. OFDM has been adopted for many types of wireless systems like wireless local area networks such as IEEE 802.11a, and digital audio/video broadcasting (DAB/DVB). The proposed research focuses on a concatenated coding scheme that improve the performance of OFDM based wireless communications. It uses a Redundant Residue Number System (RRNS) code as the outer code and a convolutional code as the inner code. The bit error rate (BER) performances of the proposed system under different channel conditions are investigated. These include the effect of additive white Gaussian noise (AWGN), multipath delay spread, peak power clipping and frame start synchronization error. The simulation results show that the proposed RRNS-Convolutional concatenated coding (RCCC) scheme provides significant improvement in the system performance by exploiting the inherent properties of RRNS.

Managing Scholarly Communication in the Web 2.0 Environment: The Role of University Libraries

Scholarly communication over the past 10 to 15 years has gained a tremendous momentum with the advent of Internet and the World Wide Web. The web has transformed the ways by which people search, find, use and communicate information. Innovations in web technology since 2005 have brought out an array of new services and facilities and an enhanced version of the web named Web 2.0. Web 2.0 facilitates a collaborative environment in which the information users can interact with the information. Web 2.0 enables its users to create, annotate, review, share re-use and represent the information in new ways thereby optimizing the information dissemination

Acoustic Structure Interaction For Floating Structure Under Moving Load

The present thesis concentrates largely on sound radiation from floating structure due to moving load

RMAC-M: Extending the R-MAC Protocol for an Energy Efficient, Delay Tolerant Underwater Acoustic Sensor Network application with a mobile data mule node

One of the major applications of underwater acoustic sensor networks (UWASN) is ocean environment monitoring. Employing data mules is an energy efficient way of data collection from the underwater sensor nodes in such a network. A data mule node such as an autonomous underwater vehicle (AUV) periodically visits the stationary nodes to download data. By conserving the power required for data transmission over long distances to a remote data sink, this approach extends the network life time. In this paper we propose a new MAC protocol to support a single mobile data mule node to collect the data sensed by the sensor nodes in periodic runs through the network. In this approach, the nodes need to perform only short distance, single hop transmission to the data mule. The protocol design discussed in this paper is motivated to support such an application. The proposed protocol is a hybrid protocol, which employs a combination of schedule based access among the stationary nodes along with handshake based access to support mobile data mules. The new protocol, RMAC-M is developed as an extension to the energy efficient MAC protocol R-MAC by extending the slot time of R-MAC to include a contention part for a hand shake based data transfer. The mobile node makes use of a beacon to signal its presence to all the nearby nodes, which can then hand-shake with the mobile node for data transfer. Simulation results show that the new protocol provides efficient support for a mobile data mule node while preserving the advantages of R-MAC such as energy efficiency and fairness.