Design and Test of a High QoS Radio Network for CBTC Systems in Subway Tunnels

Communications Based Train Control Systems require high quality radio data communications for train signaling and control. Actually most of these systems use 2.4GHz band with proprietary radio transceivers and leaky feeder as distribution system. All them demand a high QoS radio network to improve the efficiency of railway networks. We present narrow band, broad band and data correlated measurements taken in Madrid underground with a transmission system at 2.4 GHz in a test network of 2 km length in subway tunnels. The architecture proposed has a strong overlap in between cells to improve reliability and QoS. The radio planning of the network is carefully described and modeled with narrow band and broadband measurements and statistics. The result is a network with 99.7% of packets transmitted correctly and average propagation delay of 20ms. These results fulfill the specifications QoS of CBTC systems.

A Visual AGV-Urban Car using Fuzzy Control

The goal of the work described in this paper is to develop a visual line guided system for being used on-board an Autonomous Guided Vehicle (AGV) commercial car, controlling the steering and using just the visual information of a line painted below the car. In order to implement the control of the vehicle, a Fuzzy Logic controller has been implemented, that has to be robust against curvature changes and velocity changes. The only input information for the controller is the visual distance from the image center captured by a camera pointing downwards to the guiding line on the road, at a commercial frequency of 30Hz. The good performance of the controller has successfully been demonstrated in a real environment at urban velocities. The presented results demonstrate the capability of the Fuzzy controller to follow a circuit in urban environments without previous information about the path or any other information from additional sensors

HALA!'s White Paper. Towards Higher Levels of Automation in ATM

• Objectives of HALA! • Main Activities • HALA! Magement Team • Participants • Intended Audience • Heritage in ATM and Automation • The new paradigm shift in Automation in ATM • Overall system performance as main driver for ATM Automation • The three interdependent dimensions for the paradigm change. • New roles assignment based on : • “best time” • “decision place” • “best player” • HALA! main research areas

The morphofunctional approach to emotion modelling in robotics

In this conceptual paper, we discuss two areas of research in robotics, robotic models of emotion and morphofunctional machines, and we explore the scope for potential cross-fertilization between them. We shift the focus in robot models of emotion from information-theoretic aspects of appraisal to the interactive significance of bodily dispositions. Typical emotional phenomena such as arousal and action readiness can be interpreted as morphofunctional processes, and their functionality may be replicated in robotic systems with morphologies that can be modulated for real-time adaptation. We investigate the control requirements for such systems, and present a possible bio-inspired architecture, based on the division of control between neural and endocrine systems in humans and animals. We suggest that emotional epi- sodes can be understood as emergent from the coordination of action control and action-readiness, respectively. This stress on morphology complements existing research on the information-theoretic aspects of emotion.

Design and modeling of the multi-agent robotic system: SMART

This article presents the design, kinematic model and communication architecture for the multi-agent robotic system called SMART. The philosophy behind this kind of system requires the communication architecture to contemplate the concurrence of the whole system. The proposed architecture combines different communication technologies (TCP/IP and Bluetooth) under one protocol designed for the cooperation among agents and other elements of the system such as IP-Cameras, image processing library, path planner, user Interface, control block and data block. The high level control is modeled by Work-Flow Petri nets and implemented in C++ and C♯♯. Experimental results show the performance of the designed architecture.

A comparative study of SISO and MIMO control strategies for floor vibration damping

Civil engineering structures such as floor systems with open-plan layout or lightweight footbridges are susceptible to excessive level of vibrations caused by human loading. Active vibration control (AVC) via inertial mass actuators has been shown to be a viable technique to mitigate vibrations, allowing structures to satisfy vibration serviceability limits. Most of the AVC applications involve the use of SISO (single input single-output) strategies based on collocated control. However, in the case of floor structures, in which mostof the vibration modes are locally spatially distributed, SISO or multi-SISO strategies are quite inefficient. In this paper, a MIMO (multi-inputs multi-outputs) control in decentralised and centralised configuration is designed. The design process simultaneously finds the placement of multiple actuators and sensors and the output feedback gains. Additionally, actuator dynamics, actuator nonlinearities and frequency and time weightings are considered into the design process. Results with SISO and decentralised and centralised MIMO control (for a given number of actuators and sensors) are compared, showing the advantages of MIMO control for floor vibration control.

A platform for real-time control education with LEGO MINDSTORMS.

A set of software development tools for building real-time control systems on a simple robotics platform is described in the paper. The tools are being used in a real-time systems course as a basis for student projects. The development platform is a low-cost PC running GNU/Linux, and the target system is LEGO MINDSTORMS NXT, thus keeping the cost of the laboratory low. Real-time control software is developed using a mixed paradigm. Functional code for control algorithms is automatically generated in C from Simulink models. This code is then integrated into a concurrent, real-time software architecture based on a set of components written in Ada. This approach enables the students to take advantage of the high-level, model-oriented features that Simulink oers for designing control algorithms, and the comprehensive support for concurrency and real-time constructs provided by Ada.

Experiences on the specification of algorithms for fire and smoke control in road tunnels

The main objective of ventilation systems in case of fire is the reduction of the possible consequences by achieving the best possible conditions for the evacuation of the users and the intervention of the emergency services. The required immediate transition, from normal to emergency functioning of the ventilation equipments, is being strengthened by the use of automatic and semi-automatic control systems, what reduces the response times through the help to the operators, and the use of pre-defined strategies. A further step consists on the use of closed-loop algorithms, which takes into account not only the initial conditions but their development (air velocity, traffic situation, etc.), optimizing smoke control capacity.

Search strategies and the automated control of plant diseases

We propose the use of the "infotaxis" search strategy as the navigation system of a robotic platform, able to search and localize infectious foci by detecting the changes in the profile of volatile organic compounds emitted by and infected plant. We builded a simple and cost effective robot platform that substitutes odour sensors in favour of light sensors and study their robustness and performance under non ideal conditions such as the exitence of obstacles due to land topology or weeds.

Response threshold models and stochastic learning automata for self-coordination of heterogeneous multi-task distribution in multi-robot systems.

This paper focuses on the general problem of coordinating multiple robots. More specifically, it addresses the self-selection of heterogeneous specialized tasks by autonomous robots. In this paper we focus on a specifically distributed or decentralized approach as we are particularly interested in a decentralized solution where the robots themselves autonomously and in an individual manner, are responsible for selecting a particular task so that all the existing tasks are optimally distributed and executed. In this regard, we have established an experimental scenario to solve the corresponding multi-task distribution problem and we propose a solution using two different approaches by applying Response Threshold Models as well as Learning Automata-based probabilistic algorithms. We have evaluated the robustness of the algorithms, perturbing the number of pending loads to simulate the robot’s error in estimating the real number of pending tasks and also the dynamic generation of loads through time. The paper ends with a critical discussion of experimental results.

User Experience in Human-Technology Interaction. Communication, context and evaluation methodology

En esta Tesis se presentan dos líneas de investigación relacionadas y que contribuyen a las áreas de Interacción Hombre-Tecnología (o Máquina; siglas en inglés: HTI o HMI), lingüística computacional y evaluación de la experiencia del usuario. Las dos líneas en cuestión son el diseño y la evaluación centrada en el usuario de sistemas de Interacción Hombre-Máquina avanzados. En la primera parte de la Tesis (Capítulos 2 a 4) se abordan cuestiones fundamentales del diseño de sistemas HMI avanzados. El Capítulo 2 presenta una panorámica del estado del arte de la investigación en el ámbito de los sistemas conversacionales multimodales, con la que se enmarca el trabajo de investigación presentado en el resto de la Tesis. Los Capítulos 3 y 4 se centran en dos grandes aspectos del diseño de sistemas HMI: un gestor del diálogo generalizado para tratar la Interacción Hombre-Máquina multimodal y sensible al contexto, y el uso de agentes animados personificados (ECAs) para mejorar la robustez del diálogo, respectivamente. El Capítulo 3, sobre gestión del diálogo, aborda el tratamiento de la heterogeneidad de la información proveniente de las modalidades comunicativas y de los sensores externos. En este capítulo se propone, en un nivel de abstracción alto, una arquitectura para la gestión del diálogo con influjos heterogéneos de información, apoyándose en el uso de State Chart XML. En el Capítulo 4 se presenta una contribución a la representación interna de intenciones comunicativas, y su traducción a secuencias de gestos a ejecutar por parte de un ECA, diseñados específicamente para mejorar la robustez en situaciones de diálogo críticas que pueden surgir, por ejemplo, cuando se producen errores de entendimiento en la comunicación entre el usuario humano y la máquina. Se propone, en estas páginas, una extensión del Functional Mark-up Language definido en el marco conceptual SAIBA. Esta extensión permite representar actos comunicativos que realizan intenciones del emisor (la máquina) que no se pretende sean captadas conscientemente por el receptor (el usuario humano), pero con las que se pretende influirle a éste e influir el curso del diálogo. Esto se consigue mediante un objeto llamado Base de Intenciones Comunicativas (en inglés, Communication Intention Base, o CIB). La representación en el CIB de intenciones “no claradas” además de las explícitas permite la construcción de actos comunicativos que realizan simultáneamente varias intenciones comunicativas. En el Capítulo 4 también se describe un sistema experimental para el control remoto (simulado) de un asistente domótico, con autenticación de locutor para dar acceso, y con un ECA en el interfaz de cada una de estas tareas. Se incluye una descripción de las secuencias de comportamiento verbal y no verbal de los ECAs, que fueron diseñados específicamente para determinadas situaciones con objeto de mejorar la robustez del diálogo. Los Capítulos 5 a 7 conforman la parte de la Tesis dedicada a la evaluación. El Capítulo 5 repasa antecedentes relevantes en la literatura de tecnologías de la información en general, y de sistemas de interacción hablada en particular. Los principales antecedentes en el ámbito de la evaluación de la interacción sobre los cuales se ha desarrollado el trabajo presentado en esta Tesis son el Technology Acceptance Model (TAM), la herramienta Subjective Assessment of Speech System Interfaces (SASSI), y la Recomendación P.851 de la ITU-T. En el Capítulo 6 se describen un marco y una metodología de evaluación aplicados a la experiencia del usuario con sistemas HMI multimodales. Se desarrolló con este propósito un novedoso marco de evaluación subjetiva de la calidad de la experiencia del usuario y su relación con la aceptación por parte del mismo de la tecnología HMI (el nombre dado en inglés a este marco es Subjective Quality Evaluation Framework). En este marco se articula una estructura de clases de factores subjetivos relacionados con la satisfacción y aceptación por parte del usuario de la tecnología HMI propuesta. Esta estructura, tal y como se propone en la presente tesis, tiene dos dimensiones ortogonales. Primero se identifican tres grandes clases de parámetros relacionados con la aceptación por parte del usuario: “agradabilidad ” (likeability: aquellos que tienen que ver con la experiencia de uso, sin entrar en valoraciones de utilidad), rechazo (los cuales sólo pueden tener una valencia negativa) y percepción de utilidad. En segundo lugar, este conjunto clases se reproduce para distintos “niveles, o focos, percepción del usuario”. Éstos incluyen, como mínimo, un nivel de valoración global del sistema, niveles correspondientes a las tareas a realizar y objetivos a alcanzar, y un nivel de interfaz (en los casos propuestos en esta tesis, el interfaz es un sistema de diálogo con o sin un ECA). En el Capítulo 7 se presenta una evaluación empírica del sistema descrito en el Capítulo 4. El estudio se apoya en los mencionados antecedentes en la literatura, ampliados con parámetros para el estudio específico de los agentes animados (los ECAs), la auto-evaluación de las emociones de los usuarios, así como determinados factores de rechazo (concretamente, la preocupación por la privacidad y la seguridad). También se evalúa el marco de evaluación subjetiva de la calidad propuesto en el capítulo anterior. Los análisis de factores efectuados revelan una estructura de parámetros muy cercana conceptualmente a la división de clases en utilidad-agradabilidad-rechazo propuesta en dicho marco, resultado que da cierta validez empírica al marco. Análisis basados en regresiones lineales revelan estructuras de dependencias e interrelación entre los parámetros subjetivos y objetivos considerados. El efecto central de mediación, descrito en el Technology Acceptance Model, de la utilidad percibida sobre la relación de dependencia entre la intención de uso y la facilidad de uso percibida, se confirma en el estudio presentado en la presente Tesis. Además, se ha encontrado que esta estructura de relaciones se fortalece, en el estudio concreto presentado en estas páginas, si las variables consideradas se generalizan para cubrir más ampliamente las categorías de agradabilidad y utilidad contempladas en el marco de evaluación subjetiva de calidad. Se ha observado, asimismo, que los factores de rechazo aparecen como un componente propio en los análisis de factores, y además se distinguen por su comportamiento: moderan la relación entre la intención de uso (que es el principal indicador de la aceptación del usuario) y su predictor más fuerte, la utilidad percibida. Se presentan también resultados de menor importancia referentes a los efectos de los ECAs sobre los interfaces de los sistemas de diálogo y sobre los parámetros de percepción y las valoraciones de los usuarios que juegan un papel en conformar su aceptación de la tecnología. A pesar de que se observa un rendimiento de la interacción dialogada ligeramente mejor con ECAs, las opiniones subjetivas son muy similares entre los dos grupos experimentales (uno interactuando con un sistema de diálogo con ECA, y el otro sin ECA). Entre las pequeñas diferencias encontradas entre los dos grupos destacan las siguientes: en el grupo experimental sin ECA (es decir, con interfaz sólo de voz) se observó un efecto más directo de los problemas de diálogo (por ejemplo, errores de reconocimiento) sobre la percepción de robustez, mientras que el grupo con ECA tuvo una respuesta emocional más positiva cuando se producían problemas. Los ECAs parecen generar inicialmente expectativas más elevadas en cuanto a las capacidades del sistema, y los usuarios de este grupo se declaran más seguros de sí mismos en su interacción. Por último, se observan algunos indicios de efectos sociales de los ECAs: la “amigabilidad ” percibida los ECAs estaba correlada con un incremento la preocupación por la seguridad. Asimismo, los usuarios del sistema con ECAs tendían más a culparse a sí mismos, en lugar de culpar al sistema, de los problemas de diálogo que pudieran surgir, mientras que se observó una ligera tendencia opuesta en el caso de los usuarios del sistema con interacción sólo de voz. ABSTRACT This Thesis presents two related lines of research work contributing to the general fields of Human-Technology (or Machine) Interaction (HTI, or HMI), computational linguistics, and user experience evaluation. These two lines are the design and user-focused evaluation of advanced Human-Machine (or Technology) Interaction systems. The first part of the Thesis (Chapters 2 to 4) is centred on advanced HMI system design. Chapter 2 provides a background overview of the state of research in multimodal conversational systems. This sets the stage for the research work presented in the rest of the Thesis. Chapers 3 and 4 focus on two major aspects of HMI design in detail: a generalised dialogue manager for context-aware multimodal HMI, and embodied conversational agents (ECAs, or animated agents) to improve dialogue robustness, respectively. Chapter 3, on dialogue management, deals with how to handle information heterogeneity, both from the communication modalities or from external sensors. A highly abstracted architectural contribution based on State Chart XML is proposed. Chapter 4 presents a contribution for the internal representation of communication intentions and their translation into gestural sequences for an ECA, especially designed to improve robustness in critical dialogue situations such as when miscommunication occurs. We propose an extension of the functionality of Functional Mark-up Language, as envisaged in much of the work in the SAIBA framework. Our extension allows the representation of communication acts that carry intentions that are not for the interlocutor to know of, but which are made to influence him or her as well as the flow of the dialogue itself. This is achieved through a design element we have called the Communication Intention Base. Such r pr s ntation of “non- clar ” int ntions allows th construction of communication acts that carry several communication intentions simultaneously. Also in Chapter 4, an experimental system is described which allows (simulated) remote control to a home automation assistant, with biometric (speaker) authentication to grant access, featuring embodied conversation agents for each of the tasks. The discussion includes a description of the behavioural sequences for the ECAs, which were designed for specific dialogue situations with particular attention given to the objective of improving dialogue robustness. Chapters 5 to 7 form the evaluation part of the Thesis. Chapter 5 reviews evaluation approaches in the literature for information technologies, as well as in particular for speech-based interaction systems, that are useful precedents to the contributions of the present Thesis. The main evaluation precedents on which the work in this Thesis has built are the Technology Acceptance Model (TAM), the Subjective Assessment of Speech System Interfaces (SASSI) tool, and ITU-T Recommendation P.851. Chapter 6 presents the author’s work in establishing an valuation framework and methodology applied to the users’ experience with multimodal HMI systems. A novel user-acceptance Subjective Quality Evaluation Framework was developed by the author specifically for this purpose. A class structure arises from two orthogonal sets of dimensions. First we identify three broad classes of parameters related with user acceptance: likeability factors (those that have to do with the experience of using the system), rejection factors (which can only have a negative valence) and perception of usefulness. Secondly, the class structure is further broken down into several “user perception levels”; at the very least: an overall system-assessment level, task and goal-related levels, and an interface level (e.g., a dialogue system with or without an ECA). An empirical evaluation of the system described in Chapter 4 is presented in Chapter 7. The study was based on the abovementioned precedents in the literature, expanded with categories covering the inclusion of an ECA, the users’ s lf-assessed emotions, and particular rejection factors (privacy and security concerns). The Subjective Quality Evaluation Framework proposed in the previous chapter was also scrutinised. Factor analyses revealed an item structure very much related conceptually to the usefulness-likeability-rejection class division introduced above, thus giving it some empirical weight. Regression-based analysis revealed structures of dependencies, paths of interrelations, between the subjective and objective parameters considered. The central mediation effect, in the Technology Acceptance Model, of perceived usefulness on the dependency relationship of intention-to-use with perceived ease of use was confirmed in this study. Furthermore, the pattern of relationships was stronger for variables covering more broadly the likeability and usefulness categories in the Subjective Quality Evaluation Framework. Rejection factors were found to have a distinct presence as components in factor analyses, as well as distinct behaviour: they were found to moderate the relationship between intention-to-use (the main measure of user acceptance) and its strongest predictor, perceived usefulness. Insights of secondary importance are also given regarding the effect of ECAs on the interface of spoken dialogue systems and the dimensions of user perception and judgement attitude that may have a role in determining user acceptance of the technology. Despite observing slightly better performance values in the case of the system with the ECA, subjective opinions regarding both systems were, overall, very similar. Minor differences between two experimental groups (one interacting with an ECA, the other only through speech) include a more direct effect of dialogue problems (e.g., non-understandings) on perceived dialogue robustness for the voice-only interface test group, and a more positive emotional response for the ECA test group. Our findings further suggest that the ECA generates higher initial expectations, and users seem slightly more confident in their interaction with the ECA than do those without it. Finally, mild evidence of social effects of ECAs was also found: the perceived friendliness of the ECA increased security concerns, and ECA users may tend to blame themselves rather than the system when dialogue problems are encountered, while the opposite may be true for voice-only users.

Using the Cross-Entropy Method for Control Optimization: A Case Study of See-and-Avoid on Unmanned Aerial Vehicles

This paper presents an adaptation of the Cross-Entropy (CE) method to optimize fuzzy logic controllers. The CE is a recently developed optimization method based on a general Monte-Carlo approach to combinatorial and continuous multi-extremal optimization and importance sampling. This work shows the application of this optimization method to optimize the inputs gains, the location and size of the different membership functions' sets of each variable, as well as the weight of each rule from the rule's base of a fuzzy logic controller (FLC). The control system approach presented in this work was designed to command the orientation of an unmanned aerial vehicle (UAV) to modify its trajectory for avoiding collisions. An onboard looking forward camera was used to sense the environment of the UAV. The information extracted by the image processing algorithm is the only input of the fuzzy control approach to avoid the collision with a predefined object. Real tests with a quadrotor have been done to corroborate the improved behavior of the optimized controllers at different stages of the optimization process.

Modelado dinámico y control de maniobras de dispositivos submarinos

Es bien conocido por todos que la Primera Revolución Industrial, que tuvo su inicio en la segunda mitad del Siglo XVIII, conllevó un aumento del uso de los recursos energéticos que no se ha detenido para llegar a los niveles de desarrollo tecnológico, industrial y de calidad de vida, de los que se dispone en la actualidad. A simple vista podría intuirse que para disponer de un mayor nivel tecnológico, industrial, de confort, etc. sea necesario un mayor consumo de energía primaria. La actual generación de energía está principalmente basada en el procesamiento de los diversos compuestos del carbono (hidrocarburos, gases y productos derivados del petróleo), que son contaminantes y además, se agotan. Desde hace unas pocas décadas, la humanidad ha sido consciente que es necesario generar energía a partir de fuentes de origen renovable, y que además resulten menos contaminantes. Así, en la actualidad, se ha llegado a un estado de desarrollo avanzado para la explotación de diversas fuentes de energías como la eólica, a la vez que se comienza a mirar con realismo la posibilidad de explotación de diversas energías de origen marino. Se considera que las energías renovables procedentes de los océanos que se encuentran más desarrolladas tecnológicamente hablando, sin tener en cuenta la energía eólica fuera costa (offshore), son la denominada energía undimotriz o de las olas y la energía de las corrientes marinas, no necesariamente en este orden. El trabajo propuesto en esta Tesis se centra en este último recurso energético y, aunque no se dispone todavía de ningún dispositivo en fase de explotación comercial, la concepción, diseño y desarrollo de dispositivos para la extracción de energía de las corrientes, y su evolución, han sido relativamente rápidos e importantes en estos últimos años. Existen ya diferentes dispositivos en fase de pruebas con resultados muy prometedores. Aunque los dispositivos actuales se encuentran limitados a la explotación energética en zonas de poca profundidad, los diferentes estudios del recurso indican la necesidad de explotar corrientes marinas a mayores profundidades, para lo que se están desarrollando actualmente dispositivos, cuya evolución en lo que a sistemas de fondeo se refiere, está siendo muy parecida a la que se ha producido en los parques eólicos fuera costa, similar a su vez, a la evolución llevada a cabo en las plataformas oceánicas para la explotación de recursos petrolíferos (denominados oil & gas) que se extraen de profundidades cada vez mayores. Las soluciones tecnológicas que resulten válidas han de ser también económicamente viables, y en la actualidad se requiere todavía reducir costos en todas las fases de instalación, explotación y mantenimiento de estos dispositivos, sea cual sea su profundidad de operación. Uno de los focos de estudio para abaratar los costes de explotación en general, pasa por abaratar y reducir los costes en las maniobras necesarias de inmersión (de la superficie del mar a la profundidad de operación) y emersión (de la profundidad de operación a la superficie del mar) de estos dispositivos, para llevar a cabo tareas de mantenimiento in situ, en el mar, y sin necesidad de buques especializados ni de su transporte a tierra. En esta Tesis se propone, en primer lugar, un método para evaluar el ciclo de vida de diversos dispositivos de aprovechamiento de las corrientes marinas. Se evidencia que el coste de la energía así generada sigue siendo no plenamente competitivo, por lo que se requiere avanzar en el abaratamiento de costes, principalmente en la instalación y en su mantenimiento. Para ello se propone como novedad principal, introducir sistemas de control en lazo cerrado para realizar maniobras de instalación y mantenimiento de forma automática. También se aporta un modelo dinámico original y muy sencillo para dispositivos bajo estos movimientos de emersión/inmersión, a partir del cual se han desarrollado los algoritmos de control para el propósito mencionado, que no es otro sino automatizar en todo lo posible las maniobras completas. Los algoritmos de control propuestos han sido validados mediante simulación. Se proponen trayectorias de referencia de movimiento suaves (smooth) similares a las utilizadas en robótica. Estos movimientos de cambios de profundidad en lazo cerrado, combinados con secuencias de movimientos en bucle abierto para cuando el dispositivo interacciona en la superficie libre, han dado lugar a nuevas maniobras completas de instalación y mantenimiento que se presentan en esta Tesis, diferentes a las actuales. Finalmente, y como justificación de la viabilidad económica del método novedoso aportado, se ha realizado un estudio comparativo de los costes de la tecnología propuesta, frente a la tecnología actual. Este nuevo sistema de maniobras automáticas implica un ciclo de vida diferente para los dispositivos de aprovechamiento de la energía de las corrientes, ciclo que se cuantifica a partir de un dispositivo base que ha sido modificado y adaptado para la nueva tecnología propuesta, demostrando su viabilidad tanto técnica como económica. ABSTRACT It’s well known that the First Industrial Revolution started in the second half of the eighteenth century, carried the increasing of the use of energy resource which have not been stopped until reach the present technology, industrial evolution and daily life quality. On the surface, it can be known intuitively that a higher consumption of primary energy resource is demanded for benefiting from a higher technological industrial and daily life level. Today, the generation of energy is mainly based in the processing of carbon products (hydrocarbons, gases and petroleum products) which are pollutants, and additionally, are depleted. From a few decades ago, the humanity is aware the energy should be obtained from renewable resources, which besides, should be cleaner. So, at the present, a technical develop has been gained to exploit several energy source, as wind energy, and, at the same time, the extraction of the marine energy starts to seem as a reality. The renewable marine energies considered more advanced and technically developed, without keeping in mind, the offshore wind energy, are the wave energy and the tidal current energy, not necessarily in that order. This Thesis is focused in this last energy resource, and, although, any device is under commercial operation, the concept, design and develop of this type of devices to extract the tidal current energy and their evolution has been comparatively fast and important the last years. There are several devices under test with promising results. Even through the current devices are limited to lower depth areas, the several studies of the tidal energy resource suggest the need to exploit the marine current at greater depths to what is being developed devices, where their evolution in the anchoring system is being very similar to the evolution performed in the offshore wind farms, which is at the same time, similar to the evolution in the oil and gas exploitation which are extracted to greatest depths. Viable technical solutions should be also viable economically and nowadays the cost in all phases of the project (installation, maintenance and operation) should be decreased whatever the operation depth is. One focus of study to lower the operation cost is the cost decreasing of immersion manoeuvring operations (from sea surface to the operation depth) and immersion manoeuvring operations (from operation depth to the sea surface), therefore the maintenance operations can be performed on – site, in the sea, and no specialized vessels are required to transport the devices from the sea to shore. In this dissertation, firstly is proposed a method to evaluate the life cycle of the tidal energy current devices. It is proved the energy generated by these devices is not fully competitive; therefore, the cost falling is mainly an objective in the installation and the maintenance operations. For that, it is proposed as main novelty, the using of closed loop control systems to perform the automatic installation and manoeuvring operations. It is also contributed with an original and simple dynamic model and for controlling the immersion/emersion movements of these devices, from which the control algorithms are developed in order to automate as much as possible the complete manoeuvring. The control algorithms proposed has been validated by simulations. Reference paths with smooth movements, similar which are used in robotics, are suggested. These movements to change the depth using closed loop control, combined with the sequences in open loop movements when the device is in free surface, have been development for a new complete manoeuvring to installation and maintenance operations which are advanced in this Thesis and they are different to the present manoeuvrings. Finally and as justification of the economic viability of this original method, a comparative cost study between the technology proposed and the current technology is performed. This new automatic manoeuvring system involves a different life cycle for the tidal energy current devices, cycle that is quantified from a base device which has been modified and adapted for the new proposed technology, showing the technical and economic viability.

Proprioceptive force estimation and control for teleoperation in radioactive environments

A medida que se incrementa la energía de los aceleradores de partículas o iones pesados como el CERN o GSI, de los reactores de fusión como JET o ITER, u otros experimentos científicos, se va haciendo cada vez más imprescindible el uso de técnicas de manipulación remota para la interacción con el entorno sujeto a la radiación. Hasta ahora la tasa de dosis radioactiva en el CERN podía tomar valores cercanos a algunos mSv para tiempos de enfriamiento de horas, que permitían la intervención humana para tareas de mantenimiento. Durante los primeros ensayos con plasma en JET, se alcanzaban valores cercanos a los 200 μSv después de un tiempo de enfriamiento de 4 meses y ya se hacía extensivo el uso de técnicas de manipulación remota. Hay una clara tendencia al incremento de los niveles de radioactividad en el futuro en este tipo de instalaciones. Un claro ejemplo es ITER, donde se esperan valores de 450 Sv/h en el centro del toroide a los 11 días de enfriamiento o los nuevos niveles energéticos del CERN que harán necesario una apuesta por niveles de mantenimiento remotos. En estas circunstancias se enmarca esta tesis, que estudia un sistema de control bilateral basado en fuerza-posición, tratando de evitar el uso de sensores de fuerza/par, cuyo contenido electrónico los hace especialmente sensitivos en estos ambientes. El contenido de este trabajo se centra en la teleoperación de robots industriales, que debido a su reconocida solvencia y facilidad para ser adaptados a estos entornos, unido al bajo coste y alta disponibilidad, les convierte en una alternativa interesante para tareas de manipulación remota frente a costosas soluciones a medida. En primer lugar se considera el problema cinemático de teleoperación maestro-esclavo de cinemática disimilar y se desarrolla un método general para la solución del problema en el que se incluye el uso de fuerzas asistivas para guiar al operador. A continuación se explican con detalle los experimentos realizados con un robot ABB y que muestran las dificultades encontradas y recomendaciones para solventarlas. Se concluye el estudio cinemático con un método para el encaje de espacios de trabajo entre maestro y esclavo disimilares. Posteriormente se mira hacia la dinámica, estudiándose el modelado de robots con vistas a obtener un método que permita estimar las fuerzas externas que actúan sobre los mismos. Durante la caracterización del modelo dinámico, se realizan varios ensayos para tratar de encontrar un compromiso entre complejidad de cálculo y error de estimación. También se dan las claves para modelar y caracterizar robots con estructura en forma de paralelogramo y se presenta la arquitectura de control deseada. Una vez obtenido el modelo completo del esclavo, se investigan diferentes alternativas que permitan una estimación de fuerzas externas en tiempo real, minimizando las derivadas de la posición para minimizar el ruido. Se comienza utilizando observadores clásicos del estado para ir evolucionando hasta llegar al desarrollo de un observador de tipo Luenberger-Sliding cuya implementación es relativamente sencilla y sus resultados contundentes. También se analiza el uso del observador propuesto durante un control bilateral simulado en el que se compara la realimentación de fuerzas obtenida con las técnicas clásicas basadas en error de posición frente a un control basado en fuerza-posición donde la fuerza es estimada y no medida. Se comprueba como la solución propuesta da resultados comparables con las arquitecturas clásicas y sin embargo introduce una alternativa para la teleoperación de robots industriales cuya teleoperación en entornos radioactivos sería imposible de otra manera. Finalmente se analizan los problemas derivados de la aplicación práctica de la teleoperación en los escenarios mencionados anteriormente. Debido a las condiciones prohibitivas para todo equipo electrónico, los sistemas de control se deben colocar a gran distancia de los manipuladores, dando lugar a longitudes de cable de centenares de metros. En estas condiciones se crean sobretensiones en controladores basados en PWM que pueden ser destructivas para el sistema formado por control, cableado y actuador, y por tanto, han de ser eliminadas. En este trabajo se propone una solución basada en un filtro LC comercial y se prueba de forma extensiva que su inclusión no produce efectos negativos sobre el control del actuador. ABSTRACT As the energy on the particle accelerators or heavy ion accelerators such as CERN or GSI, fusion reactors such as JET or ITER, or other scientific experiments is increased, it is becoming increasingly necessary to use remote handling techniques to interact with the remote and radioactive environment. So far, the dose rate at CERN could present values near several mSv for cooling times on the range of hours, which allowed human intervention for maintenance tasks. At JET, they measured values close to 200 μSv after a cooling time of 4 months and since then, the remote handling techniques became usual. There is a clear tendency to increase the radiation levels in the future. A clear example is ITER, where values of 450 Sv/h are expected in the centre of the torus after 11 days of cooling. Also, the new energetic levels of CERN are expected to lead to a more advanced remote handling means. In these circumstances this thesis is framed, studying a bilateral control system based on force-position, trying to avoid the use of force/torque sensors, whose electronic content makes them very sensitive in these environments. The contents of this work are focused on teleoperating industrial robots, which due its well-known reliability, easiness to be adapted to these environments, cost-effectiveness and high availability, are considered as an interesting alternative to expensive custom-made solutions for remote handling tasks. Firstly, the kinematic problem of teloperating master and slave with dissimilar kinematics is analysed and a new general approach for solving this issue is presented. The solution includes using assistive forces in order to guide the human operator. Coming up next, I explain with detail the experiments accomplished with an ABB robot that show the difficulties encountered and the proposed solutions. This section is concluded with a method to match the master’s and slave’s workspaces when they present dissimilar kinematics. Later on, the research studies the dynamics, with special focus on robot modelling with the purpose of obtaining a method that allows to estimate external forces acting on them. During the characterisation of the model’s parameters, a set of tests are performed in order to get to a compromise between computational complexity and estimation error. Key points for modelling and characterising robots with a parallelogram structure are also given, and the desired control architecture is presented. Once a complete model of the slave is obtained, different alternatives for external force estimation are review to be able to predict forces in real time, minimizing the position differentiation to minimize the estimation noise. The research starts by implementing classic state observers and then it evolves towards the use of Luenberger- Sliding observers whose implementation is relatively easy and the results are convincing. I also analyse the use of proposed observer during a simulated bilateral control on which the force feedback obtained with the classic techniques based on the position error is compared versus a control architecture based on force-position, where the force is estimated instead of measured. I t is checked how the proposed solution gives results comparable with the classical techniques and however introduces an alternative method for teleoperating industrial robots whose teleoperation in radioactive environments would have been impossible in a different way. Finally, the problems originated by the practical application of teleoperation in the before mentioned scenarios are analysed. Due the prohibitive conditions for every electronic equipment, the control systems should be placed far from the manipulators. This provokes that the power cables that fed the slaves devices can present lengths of hundreds of meters. In these circumstances, overvoltage waves are developed when implementing drives based on PWM technique. The occurrence of overvoltage is very dangerous for the system composed by drive, wiring and actuator, and has to be eliminated. During this work, a solution based on commercial LC filters is proposed and it is extensively proved that its inclusion does not introduce adverse effects into the actuator’s control.

Advanced Control Strategies for a 6 DoF Hydraulic Parallel Robot Based on the Dynamic Model

Nowadays robots have made their way into real applications that were prohibitive and unthinkable thirty years ago. This is mainly due to the increase in power computations and the evolution in the theoretical field of robotics and control. Even though there is plenty of information in the current literature on this topics, it is not easy to find clear concepts of how to proceed in order to design and implement a controller for a robot. In general, the design of a controller requires of a complete understanding and knowledge of the system to be controlled. Therefore, for advanced control techniques the systems must be first identified. Once again this particular objective is cumbersome and is never straight forward requiring of great expertise and some criteria must be adopted. On the other hand, the particular problem of designing a controller is even more complex when dealing with Parallel Manipulators (PM), since their closed-loop structures give rise to a highly nonlinear system. Under this basis the current work is developed, which intends to resume and gather all the concepts and experiences involve for the control of an Hydraulic Parallel Manipulator. The main objective of this thesis is to provide a guide remarking all the steps involve in the designing of advanced control technique for PMs. The analysis of the PM under study is minced up to the core of the mechanism: the hydraulic actuators. The actuators are modeled and experimental identified. Additionally, some consideration regarding traditional PID controllers are presented and an adaptive controller is finally implemented. From a macro perspective the kinematic and dynamic model of the PM are presented. Based on the model of the system and extending the adaptive controller of the actuator, a control strategy for the PM is developed and its performance is analyzed with simulation.