Optimization of strength and toughness on the effect of the weldable high strength steels (hss) used in offshore structures

Optimization of high strength and toughness combination on the effect of weldability is very vital to be considered in offshore oil and gas industries. Having a balanced and improved high strength and toughness is very much recommended in offshore structures for an effective production and viable exploration of hydrocarbons. This thesis aims to investigate the possibilities to improve the toughness of high strength steel. High carbon contents induce hardness and needs to be reduced for increasing toughness. The rare combination of high strength with high toughness possibilities was examined by determining the following toughening mechanism of: Heat treatment and optimal microstructure, Thermomechanical processing, Effect of welding parameters on toughness and weldability of steel. The implementation of weldability of steels to attain high toughness for high strength in offshore structures is mostly in shipbuilding, offshore platforms, and pipelines for high operating pressures. As a result, the toughening mechanisms suggested have benefits to the aims of the effect of high strength to high toughness of steel for efficiency, production and cost reduction.

Pulssimuodon vaikutus valokaaren käytettävyyteen pulssi-MIG/MAG-hitsauksessa

Käytettävyydeltään huippuluokkaa olevan pulssi-MIG/MAG-hitsausvalokaaren toteuttaminen vaatii runsaasti tietoa eri pulssiparametreista ja niiden vaikutuksista hitsaukseen. Näihin vaikutuksiin liittyvä tieteellinen tutkimus on ollut melko vähäistä. Erityisesti tieto pulssimuodon vaikutuksista hitsausääneen on perustunut lähinnä kokemuksen tuomaan tuntumaan. Tässä diplomityössä tutkittiin pulssimuodon vaikutusta valokaaren käytettävyyteen pulssi-MIG/MAG-hitsauksessa. Käytettävyys käsittää tässä tapauksessa hitsausäänen, hitsin geometrian ja hitsausominaisuudet. Tutkimuksen alussa perehdyttiin kirjallisuuteen ja tuoreimpiin tutkimuksiin, jonka jälkeen vertailtiin erilaisia pulssimuotoja keskenään hitsauskokeiden avulla. Hitsausääneen ja hitsin geometriaan liittyvät kokeet suoritettiin mekanisoidusti. Hitsausääneen liittyvät mittaukset suoritettiin luokan 1 äänitasomittarilla ja tuloksia analysoitiin tietokoneohjelmistolla. Hitsien geometrioiden vertailu suoritettiin makrohietutkimuksena. Hitsausominaisuuksia tutkittiin suurnopeuskameran ja oskilloskoopin, sekä lopulta käsinhitsauskokeiden avulla. Kaikissa koevaiheissa pulssimuodon tarkasteluun käytettiin oskilloskooppia. Lisäksi käytössä oli toinen oskilloskooppi, jolla tarkasteltiin hitsausvirran spektriä. Pulssimuodon muokkaamiseen käytettiin erillistä tietokoneohjelmaa. Työn kokeellinen osuus keskittyi pulssi-MAG-hitsaukseen. Pulssimuotoa muokkaamalla saatiin aikaan miellyttävämpi hitsausääni. Lisäksi havaittiin, että pulssimuotoa muokkaamalla hitsistä saadaan kapeampi, jolloin juuritunkeumaa saavutetaan enemmän. Käsinhitsauskokeet osoittivat muokatun pulssimuodon olevan myös hitsaajan näkökulmasta käytettävyydeltään paras pulssimuoto. Erityisesti valokaaren vakaus ja kohdistuvuus sekä suurien hitsausnopeuksien sietokyky olivat muokatun pulssimuodon etuja. Selviä haittavaikutuksia pulssimuodon muokkaamiselle ei löydetty.

Weld joint characteristics by nano-materials addition

The need for industries to remain competitive in the welding business, has created necessity to develop innovative processes that can exceed customer’s demand. Significant development in improving weld efficiency, during the past decades, still have their drawbacks, specifically in the weld strength properties. The recent innovative technologies have created smallest possible solid material known as nanomaterial and their introduction in welding production has improved the weld strength properties and to overcome unstable microstructures in the weld. This study utilizes a qualitative research method, to elaborate the methods of introducing nanomaterial to the weldments and the characteristic of the welds produced by different welding processes. The study mainly focuses on changes in the microstructural formation and strength properties on the welded joint and also discusses those factors influencing such improvements, due to the addition of nanomaterials. The effect of nanomaterial addition in welding process modifies the physics of joining region, thereby, resulting in significant improvement in the strength properties, with stable microstructure in the weld. The addition of nanomaterials in the welding processes are, through coating on base metal, addition in filler metal and utilizing nanostructured base metal. However, due to its insignificant size, the addition of nanomaterials directly to the weld, would poses complications. The factors having major influence on the joint integrity are dispersion of nanomaterials, characteristics of the nanomaterials, quantity of nanomaterials and selection of nanomaterials. The addition of nanomaterials does not affect the fundamental properties and characteristics of base metals and the filler metal. However, in some cases, the addition of nanomaterials lead to the deterioration of the joint properties by unstable microstructural formations. Still research are ongoing to achieve high joint integrity, in various materials through different welding processes and also on other factors that influence the joint strength.

Hitsatun alumiinirakenteen suunnittelu

Alumiiniseosten käyttö konstruktiomateriaalina lisääntyy johtuen sen lukuisista variaatioista lujuuden ja muovattavuuden suhteen. Alumiinin keveys on merkittävä kilpailuetu teräkseen nähden. Alumiiniseosten hitsattavuus on parantunut hitsausmenetelmien kehittyessä. Uusilla menetelmillä lämmöntuontia hallitaan paremmin, kuten myös alumiinin huokoisuutta sekä lujuuden laskua hitsauksen yhteydessä. Tässä diplomityössä tutkitaan alumiinin metallurgiaa, hitsausmenetelmiä, sekä alumiinin ja teräksen sekaliitoksen toteutusta. Tutkimuksella pyritään tekemään hitsatun alumiinirakenteen suunnittelua ymmärrettävämmäksi. SFS-EN standardit antavat perustuksen alumiinirakenteen suunnittelulle. Tässä diplomityössä tehdään suunnitteluesimerkki hitsatun alumiinirakenteen hitsien suunnittelusta. Suunnitteluesimerkissä tutkitaan alumiiniseoksen lujuuden laskua hitsattaessa, ja etsitään standardien antamia ratkaisuja toimivan hitsatun rakenteen toteuttamiseksi.

Asiakasohjautuvan hitsaustuotannon kehittäminen PK-konepajassa

Tässä diplomityössä tarkasteltiin asiakasohjautuvan hitsaustuotannon kehittämistä PK-konepajassa. Työn tarkoituksena oli kerätä taustatietoa asiakasohjautuvan hitsaustuotannon erityispiirteistä ja tarkastella hitsaustuotannon kehittämistä. Työssä tutustuttiin hitsausprosesseihin ja niiden kehitysversioihin sekä hitsausaineisiin. Tärkeänä osa-alueena olivat hitsin ja hitsaustuotannon laadun ja laadunhallinnan sekä hitsauksen mekanisoinnin ja automatisoinnin tarkastelu hitsauksen työsuojelua ja hitsausergonomiaa unohtamatta. Tämän jälkeen kartoitettiin yrityksen nykytilanne ja laadittiin kehittämistoimenpiteet sekä tarvittavat laskelmat ja kehitystyön implementointi. Sen jälkeen vertailtiin tehostettua toimintaa vanhaan toimintaan sekä tehtiin johtopäätökset toiminnan kehittämisestä.

A Comparative Study Of Tensile And Microstructural Characteristics Of Friction Welded Joints And Conventionally Welded Joints Of Aluminium Alloy 6061

Welding of high strength and low weight materials like Aluminium Alloys without any defects by conventional welding techniques is a major challenge in industries. Hence research on solid state welding techniques like Friction stir welding and Friction welding techniques have got much importance in joining of Aluminium alloys. However most of the industries are not changing conventional techniques as skilled workers are available on that area. Most common conventional welding techniques used for joining of Aluminium alloys are Gas welding and Arc welding. Friction welding is a solid-state welding process that generates heat through mechanical friction between a moving and a stationary component with the addition of a lateral force called “upset” to plast ically displace and fuse the materials. In this work, experimental study on tensile and micro structural characteristics of welded joints formed from conventional welding techniques and Rotary friction welding(suitable for weld specimens with circular cross section) has been carried out and the same were compared. The process parameters for arc welding used was 50-70 Amp reverse polarity DC and electrodes of 2.3mm diameter. In Gas welding, the parameters were oxy acetylene neural flame at 3200°C and 3mm electrodes . In the case of friction welding an axial pressure loading of 3Mpa with 5 MPa as upsetting pressure and 500 rpm were used to obtain good welded joints. Tensile characteristic studies of Arc welded joints and Gas welded joints showed 48% and 60 % variations respectively from the maximum load bearing characteristics of parent metal. In the case of friction welded joint, the variation was found to 46%. Micro structural evaluation of conventionally welded joints exhibited clear distinct zones of various weld regions. In the case of friction welded joint micro structural photographs showed comparable features both in parent metal and welded region. Thus the tensile characteristic study and microstructure evaluations proved that friction welded joints are good in both aspects compared to conventionally welded joints.

Radiografia digital para inspeção de soldas de dutos - melhor sensibilidade

The conventional radiographic technique using industrial radiographic films is with the days finishing. The Digital Radiography is taking place in several sectors, e.g., the medical, aerospace, security, automotive, etc. In addition to representing a technological trend, it has been demonstrated that digital radiography offers a series of benefits in terms of productivity, sensitivity, environmental aspects, image treatment tools, cost reduction, etc. If one weld seam to be inspected is from a serried product, as example a pipe, the best option to be implemented is the Flat Panel Detector with this equipment is possible to reduce the obtaining digital radiographic images in place of films and reducing the inspection cycle time due to its high degree of automation. In the experiments described in this paper this new technique was tested and the results were compared with those obtained by the conventional radiography. The welded specimens were prepared using the submerged-arc welding process and small artificial cracks of the most varied dimensions, present in the specimens, were used to establish a comparison of the sensitivities presented by the techniques employed After conducting several experiments, the digital method presented the highest sensitivity to the wire-type Image Quality Indicator (IQI) and in the detection of small defects, leading to the conclusion that the use of digital radiography using the flat-panel detector offers advantages over the conventional technique [1, 2]. This work was carried out based on the API 5L Edition 2004 [3] and ISO 3183 Edition 2007 [4] specifications.

Microestrutura e resistência à corrosão do Ti c.p. soldado a laser utilizando em prótese sobre implantes

Foram realizados estudos para avaliar a microestrutura, a dureza e a resistência à corrosão do titânio comercialmente puro-Ti c.p. soldado por laser e utilizado na confecção de prótese sobre implantes. Verificou-se que na soldagem a laser a microestrutura apresentou três regiões distintas: o cordão de solda, a zona afetada pelo calor - ZAC e o metal base. O Ti c.p. possui microestrutura granular, a microestrutura do cordão de solda é mais refinada e de maior dureza do que o metal base. A ZAC obtida por este processo de soldagem foi relativamente pequena quando comparada com o processo de soldagem por brasagem. Os ensaios eletroquímicos mostraram que a região da solda apresentou menor resistência à corrosão em meio de NaCl 0,15 molL-1 à temperatura ambiente.

Estudo Comparativo de Juntas Soldadas a TIG e Laser Empregando-se Ti com Pureza Comercial Utilizado em Prótese sobre Implantes

Welding in the dentistry has been used for great part of the specialized dentist-surgeons in the implants area to solve prosthesis supported by implant adaptation problems. The development of new equipments Laser and TIG allowed a larger use of these processes in the prosthesis production. In this work, it was studied welded joints made by Laser and TIG, using commercial purity titanium, cpTi, applied in prosthesis supported by implants. The weld characterizations were carried out by light microscopy, EDS_elementary mapping, microhardness and tensile test. Through metallographic characterization, the weld bead presented a martensitic microstructure in the Laser welding process, originated from shear provoked by deformations in the lattice. This caused structural changes of the transformed area, which determines a fine plate-like morphology. In the weld bead from TIG, besides presenting higher hardness, was observed formation of Widmansttaten structure, which is characteristic of a geometric model, resulted of new phase formation along of the crystallographic plans. The martensitic structure is more refined than Widmansttaten structure, due to the high-speed cooling (10(3)degrees C/s) imposed by the Laser process.

Laser weld: microstructure and corrosion study of Ag-Pd-Au-Cu alloy of the dental application

The laser Welding process was introduced into dentistry by the end of the 1980s, resulting on a great impulse to that area with the development of cheaper and smaller equipment, using simpler technique. This allowed greater use of that process on the confection of prostheses compared to the brazing process since the heat source for that process is a concentrated light beam of high power, which minimizes distortion problems on the prosthetic pieces. Ag-Pd-Au-Cu alloy used on the confection of dental implant prostheses was observed before and after subjection to the laser welding process. The microstructure was analyzed with the. use of optic microscopy and the corrosion resistance was studied by the traditional electrochemical techniques and by electrochemical impedance, under environmental conditions simulating the aggressiveness found in the mouth cavity. A structural change was detected on the weld area, which presented a refined microstructure deriving from the high-speed cooling. The base metal out of the weld area presented a fusion coarse microstructure. The electrochemical essays showed differences on the potentiodynamic polarization behavior in both weld and metal base areas, indicating superior corrosion resistance in the weld area. The impedance spectra were characterized by capacitive distorted components, presenting linear impedance in the low frequencies area. (C) 2002 Elsevier B.V. B.V. All rights reserved.

Design studies of the magnetic properties of structural materials affecting the magnetic field of high-homogeneity superconducting magnets

Austenitic stainless steel presents phase changes caused by heat treatment and welding processes. Because it represents a problem in the design of high-homogeneity magnets, we have been studying the magnetic properties of Ti alloys for their use instead of stainless steel as structural material for superconducting magnet construction. In this work, we present the comparative study of the influence of magnetic properties of steel and Ti alloys on the magnetic-field homogeneity of a superconducting coil through numerical calculation using the measured magnetic properties. © 2001 Elsevier Science B.V. All rights reserved.

Avaliação da resistência ao desgaste abrasivo de revestimentos soldados do tipo Fe-C-Cr utilizados na indústria sucroalcooleira

Pós-graduação em Engenharia Mecânica - FEIS

Estudo das propriedades mecânicas de aços microligados produzidos por laminação controlada seguida de resfriamento acelerado para tubos API/DNV usado no projeto pré-sal

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação dos parâmetros de soldagem para compósitos de PPS/fibras contínuas com aplicações aeronáuticas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência do aporte de calor e da velocidade de soldagem na tenacidade da solda HF-ERW

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)