The relationship between pasture degradation and soil properties in the Brazilian amazon: a case study

Pasture degradation is one of the greatest problems related to land use in the Amazon region, forcing farmers to open new forest areas. Many studies have identified the causes and the factors involved in this degradation process, in an attempt to reverse the situation. The purpose of this study was to examine the relationship between pasture degradation and some soil properties, to try to identify the most significant soil features in the degradation process. A cattle raising farm in the eastern Amazon region, with pastures of different ages and degrees of degradation, was used as the site for this study: a primary forest area, PN; three Guinea grass (Panicum maximum Jacq.) pastures in an increasingly degraded sequence-P1, P2 and P3; one Gamba grass (Andropogon gayanus Kunth) pasture following an extremely degraded Guinea grass pasture, P4. Aboveground phytomass data showed differences between the pastures, reflecting initially observed degradation levels. Grass biomass decreased sharply from P1 to P2 and disappeared at P3. Pasture recovery with Gamba grass at P4 was very successful, with grass biomass higher than P1 and weed biomass smaller than P2 and P3. Root biomass also decreased with pasture degradation. Soil bulk density increased with pasture decrease at the topsoil layer. Results from the soil chemical analysis showed that there were no signs of decrease in organic carbon and total nitrogen after the forest was transformed into pasture. In all pastures, degraded or not, the soil pH, the sum of bases and the saturation degree were higher than in the forest soil. The extractable phosphorus content, lower in forest soil, remained quite stable in pasture soils, but it could become a limiting factor for the maintenance of Guinea grass. Results indicated that pasture degradation does not seem to be directly related to the modification of the chemical features of soils. (C) 2004 Elsevier B.V. All rights reserved.

Correction of soil acidity in the subsurface of an oxisol with sandy loam texture under no-tillage

No Rio Grande do Sul (RS), muitas áreas sob plantio direto apresentam elevada saturação por Al e baixa saturação por bases na camada de 0,10-0,20 m (subsuperfície), e isso pode diminuir a produção de grãos de culturas anuais. O objetivo do presente trabalho foi avaliar se a ocorrência de alta saturação por Al e baixa saturação por bases em subsuperfície (0,10-0,20 m), no plantio direto, pode representar um ambiente restritivo para a produção de culturas, bem como avaliar os modos de incorporação de calcário na correção da acidez do solo em subsuperfície. Para isso, foi realizado um experimento com os cultivos de soja (2005/ 2006), milho (2006/2007), trigo (2007) e soja (2007/2008), em um Latossolo Vermelho distrófico típico (Empresa Brasileira de Pesquisa Agropecuária (EMBRAPA), 2006) de textura franco arenosa, há quatro anos sob plantio direto, no município de Tupanciretã (RS). Os seis tratamentos foram: sem revolvimento com ou sem calcário; lavração com ou sem calcário; e escarificação com ou sem calcário. Aos 24 meses após a aplicação dos tratamentos e nas camadas de 0-0,05, 0,05-0,10, 0,10-0,15, 0,15-0,20 e 0,20-0,30 m, foram avaliados os valores de pH-H2O, saturação por Al e por bases. Avaliou-se a produtividade de soja (2005/2006), milho (2006/2007), trigo (2007) e soja (2007/2008). A acidez do solo em subsuperfície não alterou a produtividade das culturas quando as propriedades de acidez na camada de 0-0,10 m estavam em níveis em que não se recomenda a aplicação de calcário, segundo a CQFSRS/SC (2004). A incorporação de calcário com aração foi o modo mais eficiente de corrigir a acidez em profundidade.

Influence of organic-mineral fertilization of an oxisol on soil chemical properties and Bracharia brizantha production

A utilização de fertilizante organomineral da indústria produtora dos aminoácidos lisina e treonina pode melhorar a fertilidade de solos tropicais. O presente trabalho teve como objetivo avaliar a influência de diferentes dosagens do fertilizante organomineral denominado Ajifer L-14 nos atributos químicos e no aumento de produção de forragem de um Latossolo Vermelho do noroeste paulista. O delineamento utilizado foi em blocos casualizados, com sete tratamentos e quatro repetições. Os tratamentos foram: T1- testemunha (sem aplicação de Ajifer L-14); T2- testemunha com vegetação natural; T3- adubação mineral de acordo com a necessidade da cultura e a análise do solo (usando 1,35 kg de ureia, 2,20 kg de superfosfato simples e 0,51 kg de KCl por parcela, o que corresponde a 60 kg de N, 40 kg de P2O5 e 30 kg ha-1 de K2O, respectivamente); T4- adubação com Ajifer L-14 de acordo com a recomendação da análise química do solo (40 L parcela-1, o que corresponde a 60 kg ha-1 N); T5- adubação com Ajifer L-14 em dosagem 50 % acima da recomendação (60 L parcela-1, o que corresponde a 90 kg ha-1 N; T6- adubação com Ajifer L-14 em dosagem 50 % abaixo da recomendação (20 L parcela-1, o que corresponde a 30 kg ha-1 N); T7- adubação com Ajifer L-14 em dosagem 25 % acima da recomendação (50 L parcela-1, o que corresponde a 75 kg ha-1 N); e T8- adubação com Ajifer L-14 em dosagem 25 % abaixo da recomendação (30 L parcela-1, o que corresponde a 45 kg ha-1 N). Nas profundidades de 0,0-0,1 e 0,1-0,2 m, avaliaram-se os seguintes atributos químicos do solo:, teor de matéria orgânica (MO), pH, K+, Ca2+, Mg2+, capacidade de troca catiônica (CTC), acidez potencial e saturação por bases. A aplicação do fertilizante organomineral não influenciou os atributos químicos do solo. Na análise de regressão, houve relação polinomial entre as doses de aplicação do fertilizante organomineral e a produção de massa seca e proteína bruta de Bracharia brizantha.

Influence of liming on residual soil respiration and chemical properties in a tropical no-tillage system

Devido às mudanças climáticas do planeta, principalmente ao aquecimento global, as formas de utilização dos solos na agricultura têm atraído grande atenção de pesquisadores. Mudanças de manejo podem influenciar a respiração do solo e, por conseguinte, alterar drasticamente o sequestro de C. Os objetivos deste trabalho foram avaliar, em semeadura direta, a influência da calagem nas emissões de CO2 do solo e correlacioná-las aos atributos químicos deste após dois anos da calagem. Utilizou-se o delineamento em blocos casualizados, com seis repetições. Os tratamentos constituíram de quatro doses de calcário e uma testemunha. Decorridos dois anos da calagem, avaliou-se a emissão residual de CO2 do solo, coletaram-se amostras nas camadas de 0-5, 5-10, 10-20 e 20-30 cm de profundidade e determinaram-se os teores de P, Ca2+ e Mg2+ e valores de pH e de saturação por bases. A emissão residual de CO2 do solo, quando a dose recomendada foi aplicada, foi 24,1 % superior, quando comparada à do solo sem aplicação de calcário, e 47,4 % maior, quando se aplicou o dobro da dose recomendada. A calagem melhorou as condições químicas do solo, e a emissão de CO2 aumentou linearmente com o aumento das doses. A emissão de CO2 do solo apresentou correlações positivas com os teores de P, Ca2+ e Mg2+ e com os valores de pH e de saturação por bases e negativas com os teores de H + Al e Al3+. Maiores coeficientes de correlação entre as taxas de emissão de CO2 do solo e os atributos químicos deste ocorreram na camada de 10-20 cm.

Fractal concepts in relation to soil water diffusivity

Fractal geometry would appear to offer promise for new insight on water transport in unsaturated soils, This study was conducted to evaluate possible fractal influence on soil water diffusivity, and/or the relationships from which it arises, for several different soils, Fractal manifestations, consisting of a time-dependent diffusion coefficient and anomalous diffusion arising out of fractional Brownian motion, along with the notion of space-filling curves were gleaned from the literature, It was found necessary to replace the classical Boltzmann variable and its time t(1/2) factor with the basic fractal power function and its t(n) factor, For distinctly unsaturated soil water content theta, exponent n was found to be less than 1/2, but it approached 1/2 as theta approached its sated value, This function n = n(theta), in giving rise to a time-dependent, anomalous soil water diffusivity D, was identified with the Hurst exponent H of fractal geometry, Also, n approaching 1/2 at high water content is a behavior that makes it possible to associate factal space filling with soil that approaches water saturation, Finally, based on the fractally interpreted n = n(theta), the coalescence of both D and 8 data is greatly improved when compared with the coalescence provided by the classical Boltzmann variable.

Root growth and cotton nutrition as affected by liming and soil compaction

Soil columns were produced by filling PVC tubes with a Dark Red Latosol (Acrortox, 22% of clay). A compacted layer was established at the depth of 15 cm in the columns. In the compacted layer, soil was packed to 1.13, 1.32, 1.48, and 1.82 Mg kg(-1), resulting in cone resistances of 0.18, 0.43, 1.20, and 2.50 MPa. Cotton was cropped for 30 days. Lime was applied to raise base saturation to 40, 52, and 67%. The highest base saturation caused a decrease in phosphorus (P) and zinc (Zn) concentrations in the plants. A decrease in root dry matter, length and surface area was also observed. This could be a consequence of lime induced Zn deficiency. Root growth was decreased in the compacted layer, and complete inhibition was noticed at 2.50 MPa. Once the roots got through the compacted layer, there was a growth recovery in the bottom layer of the pots. The increase in base saturation up 52% was effective in preventing a decrease in cotton root length at soil resistances to 1.20 MPa. Where the roots were shorter, there was an increase in nutrient uptake per unit of root surface area, which kept the plants well nourished, except for P.

Soil compaction and soybean root growth

Soil compaction has a negative effect and Ca was shown to enhance root growth. The effects of soil subsurface compaction and liming on root growth and nutrient uptake by soybean were studied at the Department of Agriculture and Plant Breeding, São Paulo State University, Brazil. A Dark Red Latosol, sandy loam (Haplortox) was limed to raise base saturations to 40.1, 52.4 and 66.7%. The experimental pots were made of PVC tubes with 100 mm of diameter. Three rings with 150, 35 and 150 mm long were fixed one on the top of the other. In the central ring of 35 mm, the soil was compacted to bulk densities of 1.06, 1.25, 1.43 and 1.71 g.cm(-3). There was no effect of base saturation on soybean root and shoot growth and nutrition. Subsurface compaction led to an increase in root growth in the superficial layer of the pots with a correspondent quadratic decrease in the compacted layer. There was no effect of subsoil compaction on total root length and surface, soybean growth and nutrition. Soybean root growth was decreased by 10% and 50% when the soil penetrometer resistances were 0.52 MPa (bulk density of 1.45 g.cm(-1)) and 1.45 MPa (bulk density of 1.69 g.cm(-3)), respectively. In spite of the poor root growth in the compacted layer, once it nas overcome the root system showed an almost complete recovery.

Spatial variability of soil attributes and sugarcane yield in relation to topographic location

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Specific depth cone resistivity measurements to determine soil engineering properties

The University of British Columbia (UBC) began performing piezocone penetration tests (CPTU) with electrical resistivity measurements (RCPTU) in 1989. Since then, RCPTU research at UBC has focused on obtaining geo-environmental parameters such as fluid resistivity and soil engineering properties such as porosity and degree of saturation from measurements of bulk soil electrical resistivity using the empirical relationship proposed by Archie (1942). Within this framework, the paper illustrates and discusses important design and calibration issues for resistivity modules such as the use of isolated circuitry to achieve linear calibrations over large ranges of resistivity. The suitability of RCPTU measurements for determination of geo-environmental and geotechnical parameters are assessed using typical ranges of soil and groundwater properties and methods of isolating individual factors for study are discussed. Illustrative examples of RCPTU research efforts including the environmental characterization of mine tailings, delineation of saline water intrusions in fresh water aquifers and the quality control of geotechnical ground densification are presented throughout the text. It is shown that groundwater temperature and hence ion mobility is not significantly altered by frictional heat generated during piezocone penetration and that ratio-based approaches to monitoring soil porosity can be used to eliminate the requirement for extensive groundwater sampling programs. Lastly, it is shown that RCPTU measurements above the water table can only be made using resistivity modules that are stable over a large range of resistivities and that such measurements are the most difficult to interpret because of grain surface conduction effects and generally unknown fluid resistivities.

Potential use of the veris apparent EC sensor to predict soil texture under the semi-arid conditions of central Arizona

The operational details of the apparent electrical conductivity (ECa) sensor manufactured by Veris Technologies have been extensively documented in literature reports, but the geographical distribution of these research studies indicate a strong regional concentration in the US Mid-west and Southern states. The agricultural lands of these states diverge significantly to the soil conditions and water regime of irrigated land in the US South-western states such as Arizona where there is no previous research reports of the use of this particular sensor. The objectives of the present study were to analyze the performance of this sensor under the conditions of typical soils in irrigated farms of Central Arizona. We tested under static conditions the performance of the sensor on three soils of contrasting texture. Observations were collected as time series data as soil moisture changed from saturation to permanent wilting point. Observations were repeated at the hours of lowest and highest temperatures. In addition, this study included soil penetration resistance and salinity determinations. Preliminary results indicate that soil temperature of the upper layer caused the most dynamic change in the sensor output. The ECa curves of the three soil textures tested had well defined distinctive characteristics. Final multivariate analysis is pending.

Indicators of soil degradation in urban forests: Physical and chemical parameters

The fragmentation of forest habitats in urban areas has aroused increasing interest in recent years according to the growing environmental problems. The fragmentation of theses ecosystems is caused, in general, by the pressure of housing, agriculture and industry, causing losses in biodiversity and problems of soil degradation in the border areas of theses remnants. The establishment of indicators of soil degradation becomes essential for the implementation of conservation and reclamation. This study analyzes physical and chemical characteristics of soil under different forms of vegetation in the forest surrounding the Quilombo Forest, located in Campinas/SP - Brazil, and examines the possibility of using these indices as indicators of environmental degradation in urban remnants. The parameters analyzed were: specific weight natural (γn), specific weight of solids (γs) Ca, P, K, Mg, pH, organic matter, H + Al, Sum of Base (SB) Percent Base Saturation (V%), Cation Exchange Capacity (CEC). The study shows that in general the different forms of land used in the study area significantly changed (or according to) the physical aspects of soil The porosity and voids of the soil stood out as the best indicators of soil physical degradation in the layer 0-20 cm deep. In relation to chemical indices, the soil under the cultivation of cane sugar had a significantly higher pH, K, Ca, Mg and sum of bases. The areas of forest showed higher levels of phosphorus, organic matter and CEC, indicating the importance of maintaining vegetation and replacement for the cycling of organic matter.

Delineation of specific management areas for coffee cultivation based on the soil-relief relationship and numerical classification

Predicting and mapping productivity areas allows crop producers to improve their planning of agricultural activities. The primary aims of this work were the identification and mapping of specific management areas allowing coffee bean quality to be predicted from soil attributes and their relationships to relief. The study area was located in the Southeast of the Minas Gerais state, Brazil. A grid containing a total of 145 uniformly spaced nodes 50 m apart was established over an area of 31. 7 ha from which samples were collected at depths of 0. 00-0. 20 m in order to determine physical and chemical attributes of the soil. These data were analysed in conjunction with plant attributes including production, proportion of beans retained by different sieves and drink quality. The results of principal component analysis (PCA) in combination with geostatistical data showed the attributes clay content and available iron to be the best choices for identifying four crop production environments. Environment A, which exhibited high clay and available iron contents, and low pH and base saturation, was that providing the highest yield (30. 4l ha-1) and best coffee beverage quality (61 sacks ha-1). Based on the results, we believe that multivariate analysis, geostatistics and the soil-relief relationships contained in the digital elevation model (DEM) can be effectively used in combination for the hybrid mapping of areas of varying suitability for coffee production. © 2012 Springer Science+Business Media New York.

Effects of superficial liming and silicate application on soil fertility and crop yield under rotation

Soil acidity and low natural fertility are the main problems for grain production in Brazilian 'cerrado'. Although lime has been the most applied source for soil correction, silicate may be an alternative material due to its lower solubility and Si supply, which is beneficial to several crops. This work aimed to evaluate the efficiency of superficial liming and calcium/magnesium silicate application on soil chemical attributes, plant nutrition, yield components and final yield of a soybean/white oat/maize/bean rotation under no-tillage system in a dry-winter region. The experiment was conducted under no tillage system in a deep acid clayey Rhodic Hapludox, Botucatu-SP, Brazil. The design was the completely randomized block with sixteen replications. Treatments consisted of two sources for soil acidity correction (dolomitic lime: ECC=90%, CaO=36% and MgO=12%; calcium/magnesium silicate: ECC=80%, CaO=34%, MgO=10% and SiO2=22%) applied in October 2006 to raise base saturation up to 70% and a control, with no soil correction. Soybean and white oat were sown in 2006/2007 as the main crop and off-season, respectively. Maize and bean were cropped in the next year (2007/2008). Products from silicate dissociation reach deeper soil layers after 18months from the application, compared to liming. Additionally, silicate is more efficient than lime to increasing phosphorus availability and reducing toxic aluminum. Such benefits in soil chemical attributes were only evidenced during bean cropping, when grain yield was higher after silicate application comparatively to liming. Both correction sources were improved mineral nutrition of all the other crops, mainly Ca and Mg levels and agronomical characteristics, reflecting in higher yield. © 2012 Elsevier B.V.

Influence of Agroforestry and Traditional Management of Maize (Zea mays L.) on Soil Fertility

The aim of the work was to evaluate soil nutrient concentration at 0-5, 5-10, and 10-20 cm in maize (Zea mays L.) grown in sequence with black oats (Avena strigosa Schreb.) under Leucaena diversifolia alley cropping agroforestry system (AFS) and traditional management system/sole crop (without trees-TS), following a randomized block design. The experiment was carried out at the Brazilian Association of Biodynamic Agriculture, in Botucatu, São Paulo, Brazil. The treatments were: control (C), chemical fertilizer (F), biomass of L. diversifolia alley cropping (B), and biomass of L. diversifolia alley cropping + chemical fertilizer (B+F). After 2 yr, it was observed that pH, organic matter, and nutrient content had a tendency to show higher values in the treatments biomass+fertilizer, biomass, and fertilizer application, in both systems. Higher values in pH, organic matter, phosphorus, potassium, calcium, magnesium, sum of bases, cation exchange capacity, percentage base saturation, boron, copper, and manganese tended to occur in the agroforestry system. © 2013 Copyright Taylor and Francis Group, LLC.

Spatial distribution of Yellow Sigatoka Leaf Spot correlated with soil fertility and plant nutrition

This study analyzed the spatial distribution of Yellow Sigatoka Leaf Spot relative to soil fertility and plant nutritional status using geostatistics. The experimental area comprised 1.2 ha, where 27 points were georeferenced and spaced on a regular grid 18 × 18 m. The severity of Yellow Sigatoka, soil fertility and plant nutritional status were evaluated at each point. The spherical model was adjusted for all variables using restricted maximum likelihood. Kriging maps showed the highest infection rate of Sigatoka occurred in high areas of the field which had the highest concentration of sand, while the lowest disease was found in lower areas with lower silt, organic matter, total exchangeable bases, effective cation exchange capacity, base saturation, Ca and Mg in soil, and foliar sulfur (S). These results may help farmers manage Yellow Sigatoka disease more effectively, with balanced fertilization and reduced fungicide application. This practice minimizes the environmental impact and cost of production while contributing to production sustainability.