Microwave dielectric properties of MO -La2O3-TiO2 (M = Ca, Sr, Ba) ceramics

Single-phase polycrystalline ceramics in the MO-La2O3-Ti02 (M = Ca, Sr, Ba) system, such as cation-deficient hexagonal perovskites CaLa4Ti4O15, SrLa4Ti4O15, BaLa4Ti4O15, and Ca2La4Ti5O18 and the orthorhombic phases CaLa4Ti5O17 and CaLa8Ti9O31, were prepared through the solid-state ceramic route. The phases and structure of the ceramics were analyzed through x-ray diffraction and scanning electron microscopy. The microwave dielectric properties of the ceramics were studied using a network analyzer. The investigated ceramics show high Er in the range 42 to 54, high quality factors with Q x f in the range 16,222 to 50,215 GHz, and low Tf in the range -25 to +6 ppm3/°C. These high dielectric constant materials with high Q x f up to 50,215 GHz are suitable for applications where narrow bandwidth and extremely low insertion loss is necessary, especially at frequencies around 1.9 GHz

Acoustic and petrophysical relationships in low-shale sandstone reservoir rocks

This paper describes the measurements of the acoustic and petrophysical properties of two suites of low-shale sandstone samples from North Sea hydrocarbon reservoirs, under simulated reservoir conditions. The acoustic velocities and quality factors of the samples, saturated with different pore fluids (brine, dead oil and kerosene), were measured at a frequency of about 0.8 MHz and over a range of pressures from 5 MPa to 40 MPa. The compressional-wave velocity is strongly correlated with the shear-wave velocity in this suite of rocks. The ratio V-P/V-S varies significantly with change of both pore-fluid type and differential pressure, confirming the usefulness of this parameter for seismic monitoring of producing reservoirs. The results of quality factor measurements were compared with predictions from Biot-flow and squirt-flow loss mechanisms. The results suggested that the dominating loss in these samples is due to squirt-flow of fluid between the pores of various geometries. The contribution of the Biot-flow loss mechanism to the total loss is negligible. The compressional-wave quality factor was shown to be inversely correlated with rock permeability, suggesting the possibility of using attenuation as a permeability indicator tool in low-shale, high-porosity sandstone reservoirs.

Fatores da satisfação do cidadão com a gestão pública: um estudo sobre o orçamento participativo municipal

This thesis deals with the quality dimensions and factors affecting citizens satisfaction in the participatory budgeting process in a major city of Brazil. Participatory budgeting was introduced as a usual practice in many Brazilian cities since the 1990s. It is adapted a model proposed by Johnson et al. (2001) of customer satisfaction and loyalty antecedent factors with constructs related to governance also included, to evaluate the quality perception and satisfaction rates by citizens representatives in the participatory budgeting process. It is conducted a survey with a sample of 84 citizens representatives of the seven city regions of Natal, the capital of a Northeastern State of Brazil. It is applied descriptive and multiple regression statistical analysis. The main findings related to quality and governance constructs are that the quality factors are the main factors affecting satisfaction but also the tax construct is significative to satisfaction. More regarding it was found that for different perspective of the satisfaction there are different set of factors affecting it

Fatores da satisfação, fidelidade e recomendação em serviço de saúde: estudo em setor ambulatorial de hospital

This thesis deals with the factors affecting customer satisfaction, loyalty and recommendation in the health care sector. It is adapted a model proposed by Johnson et al. (2001) of quality and loyalty antecedent factors and it is conducted a survey with a sample of 109 customers of a hospital on the ambulatory in Natal city, a capital of a Northeastern State of Brazil. It is carried descriptive and multiple regression statistical analysis. The main findings related to satisfaction are that quality factors of doctor professionalism, clerical staff efficiency, consultancy room comfort, time to provide the medical consultancy but also hospital localization are the most significant factors affecting satisfaction. Regarding personal full loyalty, satisfaction with the hospital and affective commitment are the main factors yet for partial loyalty image and calculate commitment play the main role. For recommendation satisfaction, image and brand are the main factors. The overall model used fairly explains the satisfaction, loyalty and recommendation outcomes with varying factors regarding each final purpose, e.g. loyalty or recommendation

Medicinal Mushroom Growth as Affected by Non-Axenic Casing Soil

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Microstructure, crystalline phase, and dielectric property analyses of TiO2 composition with ZrO2 addition

For microwave applications, including mobile and satellite communications, ceramic resonators should have a high dielectric constant, low dielectric losses, and high frequency stability. In this sense, TiO2-ZrO 2 ceramics have been investigated as a function of sintering behavior, phase composition, and microstructure. The ceramics were densified reaching a value of about 86% of theoretical density at 1400°C sintering temperature. The ceramics are prepared by mixing raw materials with the following TiO2-ZrO2 weight % ratio: 100 to 0, 90 to 10, and 80 to 20, respectively. The measured dielectric constants are between 79 and 88 values, while the quality factor due to dielectric losses are between 2820 and 5170. These results point out the influence of Ti/Zr ratio on controlling the dielectric properties. © (2010) Trans Tech Publications.

Avaliação do pH, temperatura e imunoistoquímica de proteínas envolvidas na maciez da carne de ovinos

Pós-graduação em Medicina Veterinária - FMVZ

Dynamical measurements with quartz resonators

Dynamische Messungen mit Quarzresonatoren Die Resonanzfrequenz von Quarzoszillatoren liegt im MHz-Bereich. Die Resonanzen haben hohe Gueten und sind somit empfindlich auf kleine Aenderungen an der Resonatoroberflaeche. 1. Es wurde ein Aufbau entwickelt, um Reibung bei hohen Oberflaechengeschwindigkeiten zu messen (v = 1 m/s). Bei Annaeherung einer Kugel steigen Resonanzfrequenz sowie -breite des Schwingquarzes an. Für groeßere Normalkraefte entsteht ein elastischer Kontakt, der die Frequenzerhoehung erklaert. Kurz vor Eintreten dieses Kontaktes durchlaeuft die Daempfung ein Maximum, das charakteristisch ist für das Auftreten von Reibung. Bei Erhoehung der Schichtdicke (0,4-2,5 nm) einer Schmiermittelbeschichtung (Perfluoropolyether) verringern sich sowohl die Hoehe als auch die Breite dieses Maximums. Es verschwindet mit vollstaendiger Belegung mit einer Monolage (ca. 2 nm). Dies wird durch einen intermittierenden Kontakt der beiden Oberflaechen erklaert. 2. Die Schwingquarzoberfläche wurde mit Polymerbuersten verschiedener Schichtdicken (12-230 nm) beschichtet. Der Loesungsmittelgehalt in diesen Filmen variiert mit dem Dampfdruck der umgebenden Toluolatmosphaere. Bei Trocknung durchlaufen die Filme einen loesungsmittelinduzierten Glasuebergang. Die Sorptionskurven (Loesungsmittelgehalt gegen Dampfdruck) zeigen eine Knick beim Glasuebergang, ihre Ableitungen dagegen eine Stufe. Fuer duenner werdende Schichten verschiebt sich diese Stufe zu niedrigerem Dampfdruck sowie geringerem Loesungsmittelgehalt. Außerdem wird sie breiter und ihre Hoehe nimmt ab.

Bottle microresonators for applications in quantum optics and all-optical signal processing

This thesis reports on the experimental realization, characterization and application of a novel microresonator design. The so-called “bottle microresonator” sustains whispering-gallery modes in which light fields are confined near the surface of the micron-sized silica structure by continuous total internal reflection. While whispering-gallery mode resonators in general exhibit outstanding properties in terms of both temporal and spatial confinement of light fields, their monolithic design makes tuning of their resonance frequency difficult. This impedes their use, e.g., in cavity quantum electrodynamics (CQED) experiments, which investigate the interaction of single quantum mechanical emitters of predetermined resonance frequency with a cavity mode. In contrast, the highly prolate shape of the bottle microresonators gives rise to a customizable mode structure, enabling full tunability. The thesis is organized as follows: In chapter I, I give a brief overview of different types of optical microresonators. Important quantities, such as the quality factor Q and the mode volume V, which characterize the temporal and spatial confinement of the light field are introduced. In chapter II, a wave equation calculation of the modes of a bottle microresonator is presented. The intensity distribution of different bottle modes is derived and their mode volume is calculated. A brief description of light propagation in ultra-thin optical fibers, which are used to couple light into and out of bottle modes, is given as well. The chapter concludes with a presentation of the fabrication techniques of both structures. Chapter III presents experimental results on highly efficient, nearly lossless coupling of light into bottle modes as well as their spatial and spectral characterization. Ultra-high intrinsic quality factors exceeding 360 million as well as full tunability are demonstrated. In chapter IV, the bottle microresonator in add-drop configuration, i.e., with two ultra-thin fibers coupled to one bottle mode, is discussed. The highly efficient, nearly lossless coupling characteristics of each fiber combined with the resonator's high intrinsic quality factor, enable resonant power transfers between both fibers with efficiencies exceeding 90%. Moreover, the favorable ratio of absorption and the nonlinear refractive index of silica yields optical Kerr bistability at record low powers on the order of 50 µW. Combined with the add-drop configuration, this allows one to route optical signals between the outputs of both ultra-thin fibers, simply by varying the input power, thereby enabling applications in all-optical signal processing. Finally, in chapter V, I discuss the potential of the bottle microresonator for CQED experiments with single atoms. Its Q/V-ratio, which determines the ratio of the atom-cavity coupling rate to the dissipative rates of the subsystems, aligns with the values obtained for state-of-the-art CQED microresonators. In combination with its full tunability and the possibility of highly efficient light transfer to and from the bottle mode, this makes the bottle microresonator a unique tool for quantum optics applications.

Ta2O5/SiO2 insulating acoustic mirrors for AlN-based X-band BAW resonators

This work describes the performance of AlN-based bulk acoustic wave resonators built on top of insulating acoustic reflectors and operating at around 8 GHz. The acoustic reflectors are composed of alternate layers of amorphous Ta2O5and SiO2 deposited at room temperature by pulsed-DC reactive sputtering in Ar/O2 atmospheres. SiO2 layers have a porous structure that provides a low acoustic impedance of only 9.5 MRayl. Ta2O5 films exhibit an acoustic impedance of around 39.5 MRayl that was assessed by the picoseconds acoustic technique These values allow to design acoustic mirrors with transmission coefficients in the centre of the band lower than -40 dB (99.998 % of reflectance) with only seven layers. The resonators were fabricated by depositing a very thin AlN film onto an iridium bottom electrode 180 nm-thick and by using Ir or Mo layers as top electrode. Resonators with effective electromechanical coupling factors of 5.7% and quality factors at the antiresonant frequency around 600 are achieved.

Development of a Model for Security and Usability

This research addressed the development of a consolidated model designed especially to cover the security and usability attributes of a software product. As a starting point, we built a new usability model on the basis of well-known quality standards and models. We then used an existing security model to analyse the relationship between these two approaches. This analysis consisted of a systematic mapping study of the relationship between security and usability as global quality factors. We identified five relationship types: inverse, direct, relative, one-way inverse, and no relationship. Most authors agree that there is an inverse relationship between security and usability. However, this is not a unanimous finding, and this study unveils a number of open questions, like application domain dependency and the need to explore lower-level relationships between attribute subcharacteristics. In order to clarify the questions raised during the research, we conducted a second systematic mapping to further analyse the finer-grained structure of these factors, such as authentication as a subset of security and user efficiency as a subset of usability. The most relevant finding is that efficiency does not depend on the security level during the authentication process. There are other subfactors that require analysis. Accordingly, this research is the first part of a larger project to develop a full-blown consolidated model for security and usability.

Avaliação da influência dos formatos DICOM e JPEG na reprodutibilidade de pontos cefalométricos em Telerradiografia digital em Norma Frontal

A imagem digital no formato DICOM requer grande espaço para armazenamento, dificultando o arquivamento e transmissão da imagem via internet, sendo necessária, muitas vezes, a compressão das imagens por meio de formatos de arquivo como o JPEG. O objetivo neste estudo foi avaliar a influência dos formatos DICOM e JPEG, nos Fatores de Qualidade 100, 80 e 60, na reprodutibilidade intra e interexaminador na marcação de pontos cefalométricos em Telerradiografias digitais em Norma Frontal. A amostra consistiu de 120 imagens digitais de Telerradiografias em Norma Frontal, obtidas de 30 indivíduos. As 30 imagens originais, em formato DICOM, posteriormente, foram convertidas para o formato JPEG, nos Fatores de Qualidade 100, 80 e 60. Após cegar e randomizar a amostra, três ortodontistas calibrados marcaram os 18 pontos cefalométricos em cada imagem utilizando um programa de cefalometria computadorizada, que registra as medidas dos pontos cefalométricos em um sistema de coordenadas cartesianas X e Y. Nos resultados, os testes estatísticos de correlações intraclasses e análise de variância (ANOVA) apresentaram concordância de reprodutibilidade dos pontos cefalométricos em Telerradiografias digitais em Norma Frontal, tanto intra como interexaminador, com exceção dos pontos ZL, ZR, AZ, JR, NC, CN na coordenada Y e A6 na coordenada X, independentemente dos formatos de arquivo. Em conclusão, os formatos de arquivo DICOM e JPEG, nos Fatores de Qualidade 100, 80 e 60, não afetaram a reprodutibilidade intra e interexaminador na marcação dos pontos cefalométricos.(AU)

Avaliação da influência dos formatos DICOM e JPEG na reprodutibilidade de pontos cefalométricos em Telerradiografia digital em Norma Frontal

A imagem digital no formato DICOM requer grande espaço para armazenamento, dificultando o arquivamento e transmissão da imagem via internet, sendo necessária, muitas vezes, a compressão das imagens por meio de formatos de arquivo como o JPEG. O objetivo neste estudo foi avaliar a influência dos formatos DICOM e JPEG, nos Fatores de Qualidade 100, 80 e 60, na reprodutibilidade intra e interexaminador na marcação de pontos cefalométricos em Telerradiografias digitais em Norma Frontal. A amostra consistiu de 120 imagens digitais de Telerradiografias em Norma Frontal, obtidas de 30 indivíduos. As 30 imagens originais, em formato DICOM, posteriormente, foram convertidas para o formato JPEG, nos Fatores de Qualidade 100, 80 e 60. Após cegar e randomizar a amostra, três ortodontistas calibrados marcaram os 18 pontos cefalométricos em cada imagem utilizando um programa de cefalometria computadorizada, que registra as medidas dos pontos cefalométricos em um sistema de coordenadas cartesianas X e Y. Nos resultados, os testes estatísticos de correlações intraclasses e análise de variância (ANOVA) apresentaram concordância de reprodutibilidade dos pontos cefalométricos em Telerradiografias digitais em Norma Frontal, tanto intra como interexaminador, com exceção dos pontos ZL, ZR, AZ, JR, NC, CN na coordenada Y e A6 na coordenada X, independentemente dos formatos de arquivo. Em conclusão, os formatos de arquivo DICOM e JPEG, nos Fatores de Qualidade 100, 80 e 60, não afetaram a reprodutibilidade intra e interexaminador na marcação dos pontos cefalométricos.(AU)

Tight-Binding Approximations in 1D and 2D Coupled-Cavity Photonic Crystal Structures

Light confinement and controlling an optical field has numerous applications in the field of telecommunications for optical signals processing. When the wavelength of the electromagnetic field is on the order of the period of a photonic microstructure, the field undergoes reflection, refraction, and coherent scattering. This produces photonic bandgaps, forbidden frequency regions or spectral stop bands where light cannot exist. Dielectric perturbations that break the perfect periodicity of these structures produce what is analogous to an impurity state in the bandgap of a semiconductor. The defect modes that exist at discrete frequencies within the photonic bandgap are spatially localized about the cavity-defects in the photonic crystal. In this thesis the properties of two tight-binding approximations (TBAs) are investigated in one-dimensional and two-dimensional coupled-cavity photonic crystal structures We require an efficient and simple approach that ensures the continuity of the electromagnetic field across dielectric interfaces in complex structures. In this thesis we develop \textrm{E} -- and \textrm{D} --TBAs to calculate the modes in finite 1D and 2D two-defect coupled-cavity photonic crystal structures. In the \textrm{E} -- and \textrm{D} --TBAs we expand the coupled-cavity \overrightarrow{E} --modes in terms of the individual \overrightarrow{E} -- and \overrightarrow{D} --modes, respectively. We investigate the dependence of the defect modes, their frequencies and quality factors on the relative placement of the defects in the photonic crystal structures. We then elucidate the differences between the two TBA formulations, and describe the conditions under which these formulations may be more robust when encountering a dielectric perturbation. Our 1D analysis showed that the 1D modes were sensitive to the structure geometry. The antisymmetric \textrm{D} mode amplitudes show that the \textrm{D} --TBA did not capture the correct (tangential \overrightarrow{E} --field) boundary conditions. However, the \textrm{D} --TBA did not yield significantly poorer results compared to the \textrm{E} --TBA. Our 2D analysis reveals that the \textrm{E} -- and \textrm{D} --TBAs produced nearly identical mode profiles for every structure. Plots of the relative difference between the \textrm{E} and \textrm{D} mode amplitudes show that the \textrm{D} --TBA did capture the correct (normal \overrightarrow{E} --field) boundary conditions. We found that the 2D TBA CC mode calculations were 125-150 times faster than an FDTD calculation for the same two-defect PCS. Notwithstanding this efficiency, the appropriateness of either TBA was found to depend on the geometry of the structure and the mode(s), i.e. whether or not the mode has a large normal or tangential component.

FATORES DETERMINANTES DA QUALIDADE DOS SERVIÇOS EM RESTAURANTES FAST FOOD

No mundo moderno, comodidade e conveniência têm sido fatores ligados diretamente às necessidades cotidianas das pessoas, onde o tempo é cada vez mais escasso e a busca por facilidades se torna uma constante. Tendo em vista esse cenário, na mesma medida crescente do número de frequentadores em praça de alimentação, há uma concorrência intensa travada pelas empresas de fast food estabelecidas nesses centros de compras. Nesse contexto, esse trabalho identifica e analisa fatores determinantes da qualidade dos serviços de restaurantes fast food, sob a ótica dos consumidores. O setor de fast food foi dividido em três categorias: temáticos, por quilo e lanchonetes, visando identificar possíveis diferenças nesses segmentos. O universo da pesquisa concentra-se nos consumidores dos restaurantes fast food situados no principal shopping center da cidade de Mauá. A pesquisa é de caráter descritivo e exploratório, cujos dados foram coletados por meio de questionário, baseado no instrumento de análise SERVQUAL, aplicado junto a uma amostra não probabilística de 390 usuários da praça de alimentação. Foi realizada análise fatorial por meio do software estatístico SPSS v19, extraindo cinco fatores determinantes da qualidade dos serviços de restaurantes fast food. Dentre os fatores extraidos, ressaltam-se os que estão ligados à Excelência e à Personalização dos serviços. Os segmentos analisados apresentaram convergências em seus resultados, como a elevada expectativa por parte dos consumidores, além do déficit na qualidade percebida de serviços dos restaurantes fast food, assim como apresentaram divergências em suas análises individuais, evidenciando peculiaridades a cada um desses.