Production of Ti-35Nb alloy by powder metallurgy for aerospace application

Titanium and its alloys provide high strength-to-weight ratios, good fatigue strength and increased corrosion resistance compared with others materials. Its acceptance in aerospace has been limited by costs considerations such as high cost of raw material, high buy-to-fly ratios and expensive machining operations. Significant cost reductions can be obtained by vacuum sintering and powder metallurgy (P/M) techniques by producing near net shapes and consequently minimizing material waste and machining time. The Ti 35Nb alloy exhibit a low modulus of elasticity. Stemming from the unique combination of high strength, low modulus of elasticity and low density, this alloy is intrinsically more resistant to shock and explosion damages than most other engineering materials. Samples were produced by mixing of initial metallic powders followed by uniaxial and cold isostatic pressing with subsequent densification by sintering between 900 and 1600 °C, in vacuum. Sintering behavior was studied by means of dilatometry. Sintered samples were characterized for phase composition, microstructure and microhardness by X-ray diffraction, scanning electron microscopy and Vickers indentation, respectively. Density was measured by Archimedes method. Copyright © 2004 Society of Automotive Engineers, Inc.

Continuous production of metal matrix composites from the semisolid state

Continuous strip metal matrix composite (MMC) casting of 0.3 mm diameter hard-drawn stainless steel (316L) wire in a quasi-eutectic SnPb (64Sn36Pb) matrix was performed by a two-roll melt drag processing (TRMDping) method, with the wire being dragged through a semisolid puddle with a fibre contact time of approximately 0.2 s. A slag weir placed at the nozzle contained two wire guide holes: one located near the upper roll, and the other located between the rolls. A successful continuous composite strip casting with good fibre alignment was achieved by inserting and embedding the wire into the matrix using the guide hole between the rolls. Degeneration of eutectic/dendrite structures led to the formation of globular structures. The occurrence and formation mechanisms of cracks, de-lamination and voids in the matrix were discussed. TRMDping is economically viable and has significant benefits over other MMC fabrication methods. © (2013) Trans Tech Publications, Switzerland.

Production of turmeric oleoresin microcapsules by complex coacervation with gelatin-gum arabic

Turmeric oleoresin is a colorant prepared by solvent extraction of turmeric (Curcuma longa L.). Curcumin, the major pigment present in turmeric, has been described as a potent antioxidant, anti-inflammatory and anticarcinogenic agent. Turmeric pigments are lipid soluble and water insoluble and are sensitive to light, heat, oxygen and pH, which can be overcome by microencapsulation of turmeric oleoresin. The aim of this work was to investigate microencapsulation of turmeric oleoresin by complex coacervation using gelatin and gum Arabic as encapsulants and freeze-drying as the drying method. The coacervation process was studied by varying the concentration of biopolymer solution (2.5, 5.0 and 7.5%) and the core material: total encapsulant ratio (25, 50, 75 and 100%). Microcapsules were evaluated for encapsulation efficiency, morphology, solubility and stability to light. Encapsulation efficiency ranged from 49 to 73% and samples produced with 2.5% of wall material and 100% core: encapsulant ratio showed better stability to light. © 2012 Wiley Periodicals, Inc.

Yeast proteins originated from the production of brazilian bioethanol quantification and content

The purpose of this work was to determine the levels of protein and the amino acid distribution in the cell mass of yeast strains (Saccharomyces sensu stricto) originated from Brazilian bioethanol industries. The protein was analyzed with the Kjeldahl method and the amino acids, by using high-performance liquid chromatography (HPLC). The percentages of the protein found ranged from 39 to 49%. The results show that in spite of some variation in numbers between the different yeast strains, all of them presented an amino acid profile similar to the one in the literature for S. cerevisae. The amino acids that have occurred in the largest amounts were: aspartic, glutamic acids and lysine, and those in the lowest amounts were: cysteine and methionine. Although the characteristics of the feedstock used and the process conditions are determinant of the protein values obtained in dry mass, this work elucidates that the intrinsic properties of the yeast strain influence these values.

Signaling Pathways Activation by Primary Endodontic Infectious Contents and Production of Inflammatory Mediators

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Nutrient accumulation and biomass production of alfafa after soil amendment with silicates

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Assessment of fungi in soils of sugarcane crops and their potential for production of biomass-degrading enzymes

Soil management practices are konwn to affect the biomass and enzyme activities of microbial soil communities. To assess whether burning of sugarcane prior to harvesting affects the community of soilborne fungi, we collected soil simples in two sites: burned sugarcane culture prior harvesting (BS) and non-burned sugarcane culture (NBS). A total of 75 filamentous fungal isolates were recovered from soils in both sites. Trichoderma was the most prevalent genus in both sites, followed by Fusarium, Cunninghamella and Aspergillus. The Sorensen's index (0.60) suggested a slight difference in fungi associated with both areas, with high number of fungal isolates found on BB soil. The abundance of Trichoderma isolates in NBS soil was higher than BS soil; however, the abundance of Fusarium, Aspergillus and Cunninghamella was higher in the latter type of soil. In addition, fungi isolated from BS soil showed the highest production of xylanase and laccase in comparision with fungi isolated form NBS soil. Our results indicate that the different types of sugarcane harvesting apparently did not interfere with the diversity of fungal communnities as revealed by culture-dependent methods. In addition, our data indicates the potencial of fungi from soils of sugarcane crops to produce relevant enzymes related to biomass conversion.

Thermophilic fungi as new sources for production of cellulases and xylanases with potential use in sugarcane bagasse saccharification

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Production of alcoholic beverage from ginger: study of fermentation process and final product quality

Introduction: In Brazil part of the production of ginger is of inadequate quality for export. The production of spirit from felt-over rhizomes is an alternative of great interest to producers of these rhizomes. Aim: Aiming to increase the value of felt-over rhizomes, this work aimed to study the use of ginger as a raw material for alcoholic beverage production. It was evaluated the effect of fermentation conditions on the components of fermented alcoholic, as well as, the quality of alcoholic distilled beverage of ginger. Methods: Dehydrated ginger passed by enzymatic hydrolysis-saccharification processes. The hydrolysate obtained was analyzed for sugar profile in HPLC. The alcoholic fermentation process followed the central composite rotational design for three factors: fermentation temperature (23 to 37ºC), time of fermentation (17 to 33 h) and concentration of inoculum (0.22 to 3.00%). The fermented alcoholic obtained was analyzed in HPLC for the contents of ethanol, methanol, glycerol and residual sugars. The distillated alcoholic beverage of ginger was analyzed for ethanol, methanol, acetaldehyde, ethyl acetate and higher alcohols in the gas chromatography (GC). In addition, copper content and acidity were analyzed Results: Sugar profile of the ginger hydrolysate revealed the presence of 77.8% of glucose. Data analysis of fermentation process showed influence of temperature on ethanol and methanol content of the fermented alcoholic of ginger. Time of fermentation had effect on glycerol content. All parameters of process had influence on residual sugars contents. The HPLC analysis has shown presence of methanol, ethyl acetate, aldehyde, acids, higher alcohols and esters in distilled alcoholic beverage of ginger. Conclusion: Fermented alcoholic of ginger with higher levels of ethanol can be obtained under the conditions of 1.5% w/w of inoculum, 30°C of temperature and 24 hours of fermentation time. In this condition of fermentation process the beverage of ginger had good quality.

Evaluation of an In Vitro Blood-Based Assay to Detect Production of Interferon-γ By Mycobacterium Bovis–Infected White-Tailed Deer (Odocoileus Virginianus)

Tuberculosis due to Mycobacterium bovis in captive Cervidae was identified as an important disease in the United States in 1990 and prompted the addition of captive Cervidae to the USDA Uniform Methods and Rules for eradication of bovine tuberculosis. As well, M. bovis infection was identified in free-ranging white-tailed deer in northeast Michigan in 1995. Tuberculosis in both captive and free-ranging Cervidae represents a serious challenge to the eradication of M. bovis infection from the United States. Currently, the only approved antemortem tests for tuberculosis in Cervidae are the intradermal tuberculin skin test and the blood tuberculosis test (BTB). At present, the BTB is not available in North America. Tuberculin skin testing of Cervidae is time-consuming and involves repeated animal handling and risk of injury to animals and humans. This study evaluated the potential of a new blood-based assay for tuberculosis in Cervidae that would decrease animal handling, stress, and losses due to injury. In addition, a blood-based assay could provide a more rapid diagnosis. Twenty 6–9-month-old white-tailed deer, male and female, were experimentally inoculated by instillation of 300 colony-forming units of M. bovis in the tonsillar crypts. Seven, age-matched uninfected deer served as controls. Blood was collected on days 90, 126, 158, 180, 210, 238, 263, and 307 after inoculation and was analyzed for the production of interferon-γ (IFN-γ) in response to incubation with M. bovis purified protein derivative (PPDb), M. avium PPDa, pokeweed mitogen (PWM), or media alone. Production of IFN-g in response to PPDb was significantly greater (P < 0.05) at all time points in samples from M. bovis–infected deer as compared with uninfected control deer, whereas IFN-γ production to PWM did not differ significantly between infected and control deer. Measurement of IFN-γ production to PPDb may serve as a useful assay for the antemortem diagnosis of tuberculosis in Cervidae.

Secondary production of sandy beach macrofauna: An evaluation of predictive models

During the last three decades, several predictive models have been developed to estimate the somatic production of macroinvertebrates. Although the models have been evaluated for their ability to assess the production of macrobenthos in different marine ecosystems, these approaches have not been applied specifically to sandy beach macrofauna and may not be directly applicable to this transitional environment. Hence, in this study, a broad literature review of sandy beach macrofauna production was conducted and estimates obtained with cohort-based and size-based methods were collected. The performance of nine models in estimating the production of individual populations from the sandy beach environment, evaluated for all taxonomic groups combined and for individual groups separately, was assessed, comparing the production predicted by the models to the estimates obtained from the literature (observed production). Most of the models overestimated population production compared to observed production estimates, whether for all populations combined or more specific taxonomic groups. However, estimates by two models developed by Cusson and Bourget provided best fits to measured production, and thus represent the best alternatives to the cohort-based and size-based methods in this habitat. The consistent performance of one of these Cusson and Bourget models, which was developed for the macrobenthos of sandy substrate habitats (C&B-SS), shows that the performance of a model does not depend on whether it was developed for a specific taxonomic group. Moreover, since some widely used models (e.g., the Robertson model) show very different responses when applied to the macrofauna of different marine environments (e.g., sandy beaches and estuaries), prior evaluation of these models is essential.

Geopropolis from Melipona scutellaris decreases the mechanical inflammatory hypernociception by inhibiting the production of IL-1 beta and TNF-alpha

Ethnopharmacological relevance: The pharmacological activity of geopropolis collected by stingless bees (important and threatened pollinators), a product widely used in folk medicine by several communities in Brazil, especially in the Northeast Region, needs to be studied. Objective: The aim of this study was to evaluate the antinociceptive activity of Melipona scutellaris geopropolis (stingless bee) using different models of nociception. Material and methods: The antinociceptive activity of the ethanolic extract of geopropolis (EEGP) and fractions was evaluated using writhing induced by acetic acid, formalin test, carrageenan-induced hypernociception, and quantification of IL-1 beta and TNF-alpha. The chemical composition was assessed by quantification of total flavonoids and phenolic compounds. Results: EEGP and its hexane and aqueous fractions showed antinociceptive activity. Both EEGP and its aqueous fraction presented activity in the mechanical inflammatory hypernociception induced by the carrageenan model, an effect mediated by the inhibition of IL-1 beta and TNF-alpha. The chemical composition of EEGP and its hexane and aqueous fractions showed a significant presence of phenolic compounds and absence of flavonoids. Conclusion: Our data indicate that geopropolis is a natural source of bioactive substances with promising antinociceptive activity. (C) 2012 Elsevier Ireland Ltd. All rights reserved.

Transient transfection of serum-free suspension HEK 293 cell culture for efficient production of human rFVIII

Abstract Background Hemophilia A is a bleeding disorder caused by deficiency in coagulation factor VIII. Recombinant factor VIII (rFVIII) is an alternative to plasma-derived FVIII for the treatment of hemophilia A. However, commercial manufacturing of rFVIII products is inefficient and costly and is associated to high prices and product shortage, even in economically privileged countries. This situation may be solved by adopting more efficient production methods. Here, we evaluated the potential of transient transfection in producing rFVIII in serum-free suspension HEK 293 cell cultures and investigated the effects of different DNA concentration (0.4, 0.6 and 0.8 μg/106 cells) and repeated transfections done at 34° and 37°C. Results We observed a decrease in cell growth when high DNA concentrations were used, but no significant differences in transfection efficiency and in the biological activity of the rFVIII were noticed. The best condition for rFVIII production was obtained with repeated transfections at 34°C using 0.4 μg DNA/106 cells through which almost 50 IU of active rFVIII was produced six days post-transfection. Conclusion Serum-free suspension transient transfection is thus a viable option for high-yield-rFVIII production. Work is in progress to further optimize the process and validate its scalability.

Visual stimuli and written production of deaf signers

PURPOSE: To verify the interference of visual stimuli in written production of deaf signers with no complaints regarding reading and writing. METHODS: The research group consisted of 12 students with education between the 4th and 5th grade of elementary school, with severe or profound sensorineural hearing loss, users of LIBRAS and with alphabetical writing level. The evaluation was performed with pictures in a logical sequence and an action picture. The analysis used the communicative competence criteria. RESULTS: There were no differences in the writing production of the subjects for both stimuli. In all texts there was no title and punctuation, verbs were in the infinitive mode, there was lack of cohesive links and inclusion of created words. CONCLUSION: The different visual stimuli did not affect the production of texts.

Production of Z bosons in proton-proton collisions at root out s = 10 TeV: Expectations for early measurements at the ATLAS experiment

The production of the Z boson in proton-proton collisions at the LHC serves as a standard candle at the ATLAS experiment during early data-taking. The decay of the Z into an electron-positron pair gives a clean signature in the detector that allows for calibration and performance studies. The cross-section of ~ 1 nb allows first LHC measurements of parton density functions. In this thesis, simulations of 10 TeV collisions at the ATLAS detector are studied. The challenges for an experimental measurement of the cross-section with an integrated luminositiy of 100 pb−1 are discussed. In preparation for the cross-section determination, the single-electron efficiencies are determined via a simulation based method and in a test of a data-driven ansatz. The two methods show a very good agreement and differ by ~ 3% at most. The ingredients of an inclusive and a differential Z production cross-section measurement at ATLAS are discussed and their possible contributions to systematic uncertainties are presented. For a combined sample of signal and background the expected uncertainty on the inclusive cross-section for an integrated luminosity of 100 pb−1 is determined to 1.5% (stat) +/- 4.2% (syst) +/- 10% (lumi). The possibilities for single-differential cross-section measurements in rapidity and transverse momentum of the Z boson, which are important quantities because of the impact on parton density functions and the capability to check for non-pertubative effects in pQCD, are outlined. The issues of an efficiency correction based on electron efficiencies as function of the electron’s transverse momentum and pseudorapidity are studied. A possible alternative is demonstrated by expanding the two-dimensional efficiencies with the additional dimension of the invariant mass of the two leptons of the Z decay.