Photopyroelectric study of thermal properties and phase transitions in selected solids

This thesis presents in detail. the theoretical developments and calculations which are used for the simultaneous determination of thermal parameters, namely thermal diffusivity (a). thermal effusivity (e), thermal conductivity (K) and heat capacity (cr ) employing photopyroelectric technique. In our calculations. we have assumed that the pyroelectric detector is supported on a copper backing. so that there will be sufficient heat exchange between the heated pyroelectric detector and the backing so that the signal fluctuations are reduced to a minimum. Since the PPE signal depends on the properties of the detector that are also temperature dependent. a careful temperature calibration of the system need to be carried out. APPE cell has been fabricated for the measurements that can be used to measure the thermal properties of solid samples from ~ 90 K to ~ 350 K. The cell has been calibrated using standard samples and the accuracy of the technique is found to be of the order of± 1%.In this thesis, we have taken up work n photopyroelectric investigation of thermal parameters of ferroelectric crystals such as Glycine phosphite (NH3CH2COOH3P03), Triglycine sulfate and Thiourea as well as mixed valence perovskites samples such as Lead doped Lanthanum Manganate (Lal_xPb~Mn03) Calcium doped (Lal_xCaxMnOJ) and Nickel doped Lanthanum Stroncium Cobaltate (Lao~Sro5Ni,Col_x03).The three ferroelectric crystals are prepared by the slow evaporation technique and the mixed valence perovskites by solid state reaction technique.Mixed valence perovskites, with the general formula RI_xA~Mn03 (R = La. Nd or Pr and A = Ba, Ca, Sr or Pb) have been materials of intense experimental and theoretical studies over the past few years. These materials show . colossal magneloresis/ance' (CMR) in samples with 0.2 < x < 0.5 in such a doping region, resistivity exhibits a peak at T = T p' the metal - insulator transition temperature. The system exhibits metallic characteristics with d %T > Oabove Tp (wherep is the resistivity) and insulating characteristics with d % T < 0 above T p. Despite intensive investigations on the CMR phenomena and associated electrical properties. not much work has been done on the variation of thermal properties of these samples. We have been quite successful in finding out the nature of anomaly associated with thermal properties when the sample undergoes M-I transition.The ferroelectric crystal showing para-ferroelectric phase transitions - Glycine phosphite. Thiourea and Triglycine sulfate - are studied in detail in order to see how well the PPE technique enables one to measure the thermal parameters during phase transitions. It is seen that the phase transition gets clearly reflected in the variation of thermal parameters. The anisotropy in thermal transport along different crystallographic directions are explained in terms of the elastic anisotropy and lattice contribution to the thermal conductivity. Interesting new results have been obtained on the above samples and are presented in three different chapters of the thesis.In summary. we have carried investigations of the variations of the thermal parameters during phase transitions employing photopyroelectric technique. The results obtained on different systems are important not only in understanding the physics behind the transitions but also in establishing the potentiality of the PPE tool. The full potential of PPE technique for the investigation of optical and thermal properties of materials still remains to be taken advantage of by workers in this field.

The experience of immediacy: emotion and enlistment in fact-based theatre

This article discusses emotion as a strategy of political agency in post-Thatcherite documentary theatre. The 1990s saw a renaissance in theatre writing based in directness and immediacy but based in two quite different forms of drama, In-Yer-Face theatre and fact-based drama. There are clear distinctions between these forms: the new brutalist writing was aggressively provocative; documentary theatre engaged the audience by revealing an urgent truth. Both claimed a kind of realism that confronted actuality, be that of situation or experience, through forms of theatre that cultivated emotional engagement. In-Yer-Face theatre used emotional shock to penetrate the numb cynicism that its creators perceived. Documentary theatre used observation and the cultivation of sympathy to enlist its audience in a shared understanding of what was hidden, not understood or not noticed. The article analyses the functioning of emotional enlistment to engage the audience politically in two examples of documentary theatre, Black Watch and Guantanamo

An evolutionary innovation perspective on the selection of low and zero carbon technologies in new housing

The Code for Sustainable Homes (the Code) will require new homes in the United Kingdom to be ‘zero carbon’ from 2016. Drawing upon an evolutionary innovation perspective, this paper contributes to a gap in the literature by investigating which low and zero carbon technologies are actually being used by house builders, rather than the prevailing emphasis on the potentiality of these technologies. Using the results from a questionnaire three empirical contributions are made. First, house builders are selecting a narrow range of technologies. Second, these choices are made to minimise the disruption to their standard design and production templates (SDPTs). Finally, the coalescence around a small group of technologies is expected to intensify with solar-based technologies predicted to become more important. This paper challenges the dominant technical rationality in the literature that technical efficiency and cost benefits are the primary drivers for technology selection. These drivers play an important role but one which is mediated by the logic of maintaining the SDPTs of the house builders. This emphasises the need for construction diffusion of innovation theory to be problematized and developed within the context of business and market regimes constrained and reproduced by resilient technological trajectories.

Rhodosporidium toruloides cultivated in NaCl-enriched glucose-based media: adaptation dynamics and lipid production

In the present report and for the first time in the international literature, the impact of the addition of NaCl upon growth and lipid production on the oleaginous yeast Rhodosporidium toruloides was studied. Moreover, equally for first time, lipid production by R. toruloides was performed under non-aseptic conditions. Therefore, the potentiality of R. toruloides DSM 4444 to produce lipid in media containing several initial concentrations of NaCl with glucose employed as carbon source was studied. Preliminary batch-flask trials with increasing amounts of NaCl revealed the tolerance of the strain against NaCl content up to 6.0% (w/v). However, 4.0% (w/v) of NaCl stimulated lipid accumulation for this strain, by enhancing lipid production up to 71.3% (w/w) per dry cell weight. The same amount of NaCl was employed in pasteurized batch-flask cultures in order to investigate the role of the salt as bacterial inhibiting agent. The combination of NaCl and high glucose concentrations was found to satisfactorily suppress bacterial contamination of R. toruloides cultures under these conditions. Batch-bioreactor trials of the yeast in the same media with high glucose content (up to 150 g/L) resulted in satisfactory substrate assimilation, with almost linear kinetic profile for lipid production, regardless of the initial glucose concentration imposed. Finally, fed-batch bioreactor cultures led to the production of 37.2 g/L of biomass, accompanied by 64.5% (w/w) of lipid yield. Lipid yield per unit of glucose consumed received the very satisfactory value of 0.21 g/g, a value amongst the highest ones in the literature. The yeast lipid produced contained mainly oleic acid and to lesser extent palmitic and stearic acids, thus constituting a perfect starting material for “second generation” biodiesel

A compound class of Weibull and power series distributions

In this paper we introduce the Weibull power series (WPS) class of distributions which is obtained by compounding Weibull and power series distributions where the compounding procedure follows same way that was previously carried out by Adamidis and Loukas (1998) This new class of distributions has as a particular case the two-parameter exponential power series (EPS) class of distributions (Chahkandi and Gawk 2009) which contains several lifetime models such as exponential geometric (Adamidis and Loukas 1998) exponential Poisson (Kus 2007) and exponential logarithmic (Tahmasbi and Rezaei 2008) distributions The hazard function of our class can be increasing decreasing and upside down bathtub shaped among others while the hazard function of an EPS distribution is only decreasing We obtain several properties of the WPS distributions such as moments order statistics estimation by maximum likelihood and inference for a large sample Furthermore the EM algorithm is also used to determine the maximum likelihood estimates of the parameters and we discuss maximum entropy characterizations under suitable constraints Special distributions are studied in some detail Applications to two real data sets are given to show the flexibility and potentiality of the new class of distributions (C) 2010 Elsevier B V All rights reserved

Automated two-dimensional separation flow system with electrochemical preconcentration, stripping, capillary electrophoresis and contactless conductivity detection for trace metal ion analysis

This paper describes the automation of a fully electrochemical system for preconcentration, cleanup, separation and detection, comprising the hyphenation of a thin layer electrochemical flow cell with CE coupled with contactless conductivity detection (CE-C(4)D). Traces of heavy metal ions were extracted from the pulsed-flowing sample and accumulated on a glassy carbon working electrode by electroreduction for some minutes. Anodic stripping of the accumulated metals was synchronized with hydrodynamic injection into the capillary. The effect of the angle of the slant polished tip of the CE capillary and its orientation against the working electrode in the electrochemical preconcentration (EPC) flow cell and of the accumulation time were studied, aiming at maximum CE-C(4)D signal enhancement. After 6 min of EPC, enhancement factors close to 50 times were obtained for thallium, lead, cadmium and copper ions, and about 16 for zinc ions. Limits of detection below 25 nmol/L were estimated for all target analytes but zinc. A second separation dimension was added to the CE separation capabilities by staircase scanning of the potentiostatic deposition and/or stripping potentials of metal ions, as implemented with the EPC-CE-C(4)D flow system. A matrix exchange between the deposition and stripping steps, highly valuable for sample cleanup, can be straightforwardly programmed with the multi-pumping flow management system. The automated simultaneous determination of the traces of five accumulable heavy metals together with four non-accumulated alkaline and alkaline earth metals in a single run was demonstrated, to highlight the potentiality of the system.

Pregnancy-related low back pain and pelvic girdle pain approximately 14 months after pregnancy : pain status, self-rated health and family situation

Background: Pelvic girdle pain (PGP) in pregnancy is distinct from pregnancy-related low back pain (PLBP). However, women with combined PLBP and PGP report more serious consequences in terms of health and function. PGP has been estimated to affect about half of pregnant women, where 25% experience serious pain and 8% experience severe disability. To date there are relatively few studies regarding persistent PLBP/PGP postpartum of more than 3 months, thus the main objective was to identify the prevalence of persistent PLBP and PGP as well as the differences over time in regard to pain status, self-rated health (SRH) and family situation at 12 months postpartum. Methods: The study is a 12 month follow-up of a cohort of pregnant women developing PLBP and PGP during pregnancy, and who experienced persistent pain at 6 month follow-up after pregnancy. Women reporting PLBP/PGP (n = 639) during pregnancy were followed up with a second questionnaire at approximately six month after delivery. Women reporting recurrent or persistent LBP/PGP at the second questionnaire (n = 200) were sent a third questionnaire at 12 month postpartum. Results: A total of 176 women responded to the questionnaire. Thirty-four women (19.3%) reported remission of LBP/PGP, whereas 65.3% (n = 115) and 15.3% (n = 27), reported recurrent LBP/PGP or continuous LBP/PGP, respectively. The time between base line and the 12 months follow-up was in actuality 14 months. Women with previous LBP before pregnancy had an increased odds ratio (OR) of reporting 'recurrent pain' (OR = 2.47) or 'continuous pain' (OR = 3.35) postpartum compared to women who reported 'no pain' at the follow-up. Women with 'continuous pain' reported statistically significant higher level of pain at all measure points (0, 6 and 12 months postpartum). Non-responders were found to report a statistically significant less positive scoring regarding relationship satisfaction compared to responders. Conclusions: The results from this study demonstrate that persistent PLBP/PGP is a major individual and public health issue among women 14 months postpartum, negatively affecting their self-reported health. However, the perceived relationship satisfaction seems to be stable between the groups.

Tailoring the Structural Properties of PVDF and P(VDF-TrFE) by Using Natural Polymers as Additives

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Granulocytic sarcoma of the small intestine with CBF beta/MYH11 fusion gene: report of an aleukaemic case and review of the literature

Granulocytic sarcomas (GS) are rare extramedullary tumours composed of immature myeloid cells. Inversion of chromosome 16 [inv(16)] is a cytogenetic marker for M4Eo subtype of acute myeloid leukaemia (AML). The possibility of an association between the development of granulocytic sarcoma of the small intestine (GSSI) and the M4Eo subtype of AML was suggested in nine previous case reports.Here we report an aleukaemic case of GSSI with inv(16) and its molecular equivalent, the CBFbeta/MYH11 fusion gene, detected by reverse transcriptase-polymerase chain reaction (RT-PCR), that after treatment with conventional AML chemotherapy followed by autologous bone marrow transplantation, achieved complete haematological and molecular remission on bone marrow examination. After chemotherapy, a thickened ileum wall positive for CBFbeta/MYH11 on tumour mass samples was still observed on computed tomography (CT) studies, raising the question of residual GS representing a reservoir of malignant cells. This case demonstrates the critical need of multidisciplinary diagnosis and follow-up of this entity combining immunopathologic, cytogenetic and molecular studies, reinforcing the potentiality of risk-adapted therapy strategies, as it is increasingly claimed for patients with overt AML. (C) 2003 Elsevier Ltd. All rights reserved.

Use of commercial anion-exchange resins as solid support for peptide synthesis and affinity chromatography

This report demonstrates that due to the presence of residual reactive sites in their matrices, classical diethylaminoethyl-attaching commercial anion-exchanger resins such as DEAE-MacroPrep and DEAE-Sephadex A50 supports can be used for peptide synthesis. Moreover, due to the high stability of the peptide-resin bond in the final cleavage treatments, desired peptidyl-resins free of side-chain protecting groups, which enables them to be further used as solid support for affinity chromatography, can be obtained. To demonstrate this potentiality, a fragment corresponding to the antigenic and immunodominant epitope of sporozoites of the Plasmodium falciparum malaria parasite was synthesized in these traditional resins and antibody molecules generated against the peptide sequence were successfully retained in these peptidyl supports. Due to the maintenance of their original anion-exchange capacities, the present findings open the unique possibility of applying, simultaneously, dual anion-exchange and affinity procedures for purification of a variety of macromolecules. (C) 2003 Elsevier B.V. (USA). All rights reserved.

Non-linear analysis of reinforced concrete plates by the boundary element method and continuum damage mechanics

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Signal and backgrounds for the single production of scalar and vector leptoquarks at the CERN LHC

We perform a detailed analysis of the potentiality of the CERN Large Hadron Collider to study the single production of leptoquarks via pp→e±q→ leptoquark →e± q, with e± generated by the splitting of photons radiated by the protons. Working with the most general SU(2)L⊗U( 1 )Y invariant effective Lagrangian for scalar and vector leptoquarks, we analyze in detail the leptoquark signals and backgrounds that lead to a final state containing an e± and a hard jet with approximately balanced transverse momenta. Our results indicate that the LHC will be able to discover leptoquarks with masses up to 2-3 TeV, depending on their type, for Yukawa couplings of the order of the electromagnetic one.

New Higgs couplings at e+e- and hadronic colliders

We examine the potentiality of both CERN LEP and Fermilab Tevatron colliders to establish bounds on new couplings involving the bosonic sector of the standard model. We pay particular attention to the anomalous Higgs interactions with γ, W±, and Z0. A combined exclusion plot for the coefficients of different anomalous operators is presented. The sensitivity that can be achieved at the Next Linear Collider and at the upgraded Tevatron is briefly discussed. ©1999 The American Physical Society.

Diphoton signals for large extra dimensions at the Fermilab Tevatron and CERN LHC

We analyze the potentiality of hadron colliders to search for large extra dimensions via the production of photon pairs. The virtual exchange of Kaluza-Klein gravitons can significantly enhance this process provided the quantum gravity scale (MS) is in the TeV range. We studied in detail the subprocesses qq̄→γγ and gg → γγ taking into account the complete standard model and graviton contributions as well as the unitarity constraints. We show that the Fermilab Tevatron run II will be able to probe MS up to 1.5-1.9 TeV at 2σ level, while the CERN LHC can extend this search to 5.3-6.7 TeV, depending on the number of extra dimensions. ©2000 The American Physical Society.

Production and heat treatment of cast graphitic steels with additions of niobium

The optimal combination of the mechanical characteristics of austempered spheroidal graphitic cast steel together with modern casting techniques yielded an economically promising product. The maximum potentiality of the usage of these steels is related to fabrication and characterization techniques, among which, one of the most important is the cooling diagram (TTT curve). In this work, 3 heats of graphitic steels with the following nominal compositions were cast: 1.0%C, 2.3%Si, 0.4% Mn, and with niobium contents of 0.0%, 0.5% and 1.0%. TTT curves were determined by dilatometric testing and test specimens of these steels were austempered. The samples were then characterized by hardness testing and optical and SEM microscopy. Tensile, impact (no notch) and wear testing were also performed. The addition of niobium produced significant alterations in the TTT diagrams. Increasing niobium content moves the pearlite transformation nose to the right and the bainitic transformation nose to the left. Tensile strength of these alloys was high, in the range of 1700 MPa and impact values were around of 45 Joules for alloy with 1% Nb, 49 Joules for alloy with 0.5% Nb and fracture did not occur for the alloy without the addition of Nb.