Continuous wave ultraviolet light-induced fiber Bragg gratings in few- And single-mode microstructured polymer optical fibers

We report observations and measurements of the inscription of fiber Bragg gratings (FBGs) in two different types of microstructured polymer optical fiber: few-mode and an endlessly single mode. Contrary to the FBG inscription in silica microstructured fiber, where high-energy laser pulses are a prerequisite, we have successfully used a low-power cw laser source operating at 325 nm to produce 1 cm long gratings with a reflection peak at 1570 nm. Peak reflectivities of more than 10% have been observed. © 2005 Optical Society of America.

Biconical-taper-assisted fiber interferometer with modes coupling enhancement for high-sensitive curvature measurement

A modal interferometer based on multimode-singlemode-multimode fiber structure built with a biconical taper for fiber curvature measurement is proposed and experimentally demonstrated. Due to the tapered singlemode fiber acting as a high-efficient mode power converter to enhance the modes coupling, curvature sensor with improved sensitivity is achieved by monitoring the defined fringe visibility of the interference spectrum. The measuring range can be tuned by changing the waist diameter of the fiber taper. Meanwhile, the sensor shows an intrinsic ability to overcome the influence of temperature cross-sensitivity and the power fluctuation of light source. The advantages of easy fabrication, high-quality spectrum with improved sensitivity, and small hysteresis will provide great potential for practical applications of the sensor. © 2013 Springer-Verlag Berlin Heidelberg.

A low-cost multimode fiber Bragg grating sensor system

A low-cost fiber optic sensor system based on multimode fiber and an LED light source is presented. A multimode fiber Bragg grating (MMFBG) element is used as a strain sensor. In a matched grating scheme, a MMFBG similar to the sensing one was used as a reference in the receiving unit. For detection of large wavelength shift we demonstrated the feasibility of MMFBG wavelength detection using a single mode fiber fused coupler edge filter. The high cost normally associated with wavelength interrogators for single mode fiber FBG sensors was overcome by the utilization of a low cost multimode fiber pigtailed LED light source. The multimode fiber sensing system has the potential of maintaining much of the advantages of its single mode FBG sensor system counterparts. The MMFBG sensing schemes could be used for short distance, high sensitivity, high speed, strain, temperature and acoustic sensing applications.

Long-range and high-resolution correlation optical time-domain reflectometry utilizing an all optical chaotic source

A high resolution optical time domain reflectometry (OTDR) based on an all-fiber chaotic source is demonstrated. We analyze the key factors limiting the operational range of such an OTDR, e.g., integral Rayleigh backscattering and the fiber loss, which degrade the optical signal to noise ratio at the receiver side, and then the guideline for counter-act such signal fading is discussed. The experimentally demonstrated correlation OTDR presents ability of 100km sensing range and 8.2cm spatial resolution (1.2 million resolved points), as a verification of the theoretical analysis. To the best of our knowledge, this is the first time that correlation OTDR measurement is performed over such a long distance with such high precision.

All-fiber loading sensor based on a hybrid 45° and 81° tilted fiber grating structure

We experimentally demonstrate an all-fiber loading sensor system based on a 45° and an 81° tilted fiber grating (TFG). We have fabricated two TFGs adjacent to each other in a single fiber to form a hybrid structure. When the transverse load applied to the 81° TFG, the light coupling to the two orthogonally polarized modes will interchange the power according to the load applied to the fiber, which provides a solution to measure the load. For real applications, we further investigated the interrogation of this all-fiber loading sensor system using a low-cost and compact-size single wavelength source and a power meter. The experimental results have clearly shown that a low-cost high-sensitivity loading sensor system can be developed based on the proposed TFG configuration.

An integrated functional mapping and source localization platform for brain research

The premise of this dissertation is to create a highly integrated platform that combines the most current recording technologies for brain research through the development of new algorithms for three-dimensional (3D) functional mapping and 3D source localization. The recording modalities that were integrated include: Electroencephalography (EEG), Optical Topographic Maps (OTM), Magnetic Resonance Imaging (MRI), and Diffusion Tensor Imaging (DTI). This work can be divided into two parts: The first part involves the integration of OTM with MRI, where the topographic maps are mapped to both the skull and cortical surface of the brain. This integration process is made possible through the development of new algorithms that determine the probes location on the MRI head model and warping the 2D topographic maps onto the 3D MRI head/brain model. Dynamic changes of the brain activation can be visualized on the MRI head model through a graphical user interface. The second part of this research involves augmenting a fiber tracking system, by adding the ability to integrate the source localization results generated by commercial software named Curry. This task involved registering the EEG electrodes and the dipole results to the MRI data. Such Integration will allow the visualization of fiber tracts, along with the source of the EEG, in a 3D transparent brain structure. The research findings of this dissertation were tested and validated through the participation of patients from Miami Children Hospital (MCH). Such an integrated platform presented to the medical professionals in the form of a user-friendly graphical interface is viewed as a major contribution of this dissertation. It should be emphasized that there are two main aspects to this research endeavor: (1) if a dipole could be situated in time at its different positions, its trajectory may reveal additional information on the extent and nature of the brain malfunction; (2) situating such a dipole trajectory with respect to the fiber tracks could ensure the preservation of these fiber tracks (axons) during surgical interventions, preserving as a consequence these parts of the brain that are responsible for information transmission.

Optical fiber sensors embedded in flexible polymer foils

In traditional electrical sensing applications, multiplexing and interconnecting the different sensing elements is a major challenge. Recently, many optical alternatives have been investigated including optical fiber sensors of which the sensing elements consist of fiber Bragg gratings. Different sensing points can be integrated in one optical fiber solving the interconnection problem and avoiding any electromagnetical interference (EMI). Many new sensing applications also require flexible or stretchable sensing foils which can be attached to or wrapped around irregularly shaped objects such as robot fingers and car bumpers or which can even be applied in biomedical applications where a sensor is fixed on a human body. The use of these optical sensors however always implies the use of a light-source, detectors and electronic circuitry to be coupled and integrated with these sensors. The coupling of these fibers with these light sources and detectors is a critical packaging problem and as it is well-known the costs for packaging, especially with optoelectronic components and fiber alignment issues are huge. The end goal of this embedded sensor is to create a flexible optical sensor integrated with (opto)electronic modules and control circuitry. To obtain this flexibility, one can embed the optical sensors and the driving optoelectronics in a stretchable polymer host material. In this article different embedding techniques for optical fiber sensors are described and characterized. Initial tests based on standard manufacturing processes such as molding and laser structuring are reported as well as a more advanced embedding technique based on soft lithography processing.

Flat-top supercontinuum and tunable femtosecond fiber laser sources at 1.9-2.5 μm

We report the high-energy flat-top supercontinuum covering the mid-infrared wavelength range of 1.9-2.5 μm as well as electronically tunable femtosecond pulses between 1.98-2.22 μm directly from the thulium-doped fiber laser amplifier. Comparison of experimental results with numerical simulations confirms that both sources employ the same nonlinear optical mechanism - Raman soliton frequency shift occurring inside the Tm-fiber amplifier. To illustrate that, we investigate two versions of the compact diode-pumped SESAM mode-locked femtosecond thulium-doped all-silica-fiber-based laser system providing either broadband supercontinuum or tunable Raman soliton output, depending on the parameters of the system. The first system operates in the Raman soliton regime providing femtosecond pulses tunable between 1.98-2.22 μm. Wide and continuous spectral tunability over 240 nm was realized by changing only the amplifier pump diode current. The second system generates high-energy supercontinuum with the superior spectral flatness of better than 1 dB covering the wavelength range of 1.9-2.5 μm, with the total output energy as high as 0.284 μJ, the average power of 2.1 W at 7.5 MHz repetition rate. We simulate the amplifier operation in the Raman soliton self-frequency shift regime and discuss the role of induced Raman scattering in supercontinuum formation inside the fiber amplifier. We compare this system with a more traditional 1.85-2.53 μm supercontinuum source in the external highly-nonlinear commercial chalcogenide fiber using the Raman soliton MOPA as an excitation source. The reported systems1 can be readily applied to a number of industrial applications in the mid-IR, including sensing, stand-off detection, medical surgery and fine material processing.

Fiber Bragg Gratings Strain Sensors for Railway Applications

Fiber optical sensors have played an important role in applications for monitoring the health of civil infrastructures, such as bridges, oil rigs, and railroads. Due to the reduction in cost of fiber-optic components and systems, fiber optical sensors have been studied extensively for their higher sensitivity, precision and immunity to electrical interference compared to their electrical counterparts. A fiber Bragg grating (FBG) strain sensor has been employed for this study to detect and distinguish normal and lateral loads on rail tracks. A theoretical analysis of the relationship between strain and displacement under vertical and horizontal strains on an aluminum beam has been performed, and the results are in excellent agreement with the measured strain data. Then a single FBG sensor system with erbium-doped fiber amplifier broadband source has been carried out. Force and temperature applied on the system have resulted in changes of 0.05 nm per 50 με and 0.094 nm per 10 oC at the center wavelength of the FBG. Furthermore, a low cost fiber-optic sensor system with a distributed feedback (DFB) laser as the light source has been implemented. We show that it has superior noise and sensitivity performances compared to strain gauge sensors. The design has been extended to accommodate multiple sensors with negligible cross talk. When two cascaded sensors on a rail track section are tested, strain readings of the sensor 20 inches away from the position of applied force decay to one seventh of the data of the sensor at the applied force location. The two FBG sensor systems can detect 1 ton of vertical load with a square wave pattern and 0.1 ton of lateral loads (3 tons and 0.5 ton, respectively, for strain gauges). Moreover, a single FBG sensor has been found capable of detecting and distinguishing lateral and normal strains applied at different frequencies. FBG sensors are promising alternatives to electrical sensors for their high sensitivity,ease of installation, and immunity to electromagnetic interferences.

Gaussian entanglement for quantum key distribution from a single-mode squeezing source

We report the suitability of an Einstein-Podolsky-Rosen entanglement source for Gaussian continuous-variable quantum key distribution at 1550 nm. Our source is based on a single continuous-wave squeezed vacuum mode combined with a vacuum mode at a balanced beam splitter. Extending a recent security proof, we characterize the source by quantifying the extractable length of a composable secure key from a finite number of samples under the assumption of collective attacks. We show that distances in the order of 10 km are achievable with this source for a reasonable sample size despite the fact that the entanglement was generated including a vacuum mode. Our security analysis applies to all states having an asymmetry in the field quadrature variances, including those generated by superposition of two squeezed modes with different squeezing strengths.

Effect of proteolytic enzyme and fiber of papaya fruit on human digestive health

The World Health Organization (WHO, 2005) recommends consumption of fruits and vegetables as part of a healthy diet with daily recommendation of 5 servings or at least 400 g per day. Fruits and vegetables are good sources of vitamins, minerals, antioxidants, and fiber. Papaya fruit is known for his high nutrient and fiber content, and with few exceptions, it is generally consumed ripe due to its characteristic flavor and aroma. Digestion improvement has been attributed to consumption of papaya; this we speculate is attributed to the fiber content and proteolytic enzymes associated with this highly nutritious fruit. However, research is lacking that evaluates the impact of papaya fruit on human digestion. Papain is a proteolytic enzyme generally extracted from the latex of unripe papaya. Previous research has focused on evaluating papain activity from the latex of different parts of the plant; however there are no reports about papain activity in papaya pulp through fruit maturation. The activity of papain through different stages of ripeness of papaya and its capacity of dislodging meat bolus in an in vitro model was addressed. The objective of this study was to investigate whether papain activity and fiber content are responsible for the digestive properties attributed to papaya and to find a processing method that preserves papaya health properties with minimal impact on flavor. Our results indicated that papain was active at all maturation stages of the fruit. Ripe papaya pulp displayed the highest enzyme activity and also presented the largest meat bolus displacement. The in vitro digestion study indicated that ripe papaya displayed the highest protein digestibility; this is associated with proteolytic enzymes still active at the acidity of the stomach. Results from the in vitro fermentation study indicated that ripe papaya produced the highest amount of Short Chain Fatty Acids SCFA of the three papaya substrates (unripe, ripe, and processed). SCFA are the most important product of fermentation and are used as indicators of the amount of substrate fermented by microorganisms in the colon. The combination of proteolytic enzymes and fiber content found in papaya make of this fruit not only a potential digestive aid, but also a good source of SCFA and their associated potential health benefits. Irradiation processing had minimal impact on flavor compounds of papaya nectar. However, processed papaya experienced the lowest protein digestibility and SCFA production among the papaya substrates. Future research needs to explore new processing methods for papaya that minimize the detrimental impact on enzyme activity and SCFA production.

Latvian citizens knowledge about dietary fiber

The positive benefits of DF associated with the regulation of the intestinal transit, and the prevention or treatment of diabetes, cardiovascular diseases and regulate colon cancer and obesity. The aim of this research was to collect information on knowledge about dietary fibre on citizens’ of Latvia. The questionnaire consists 22 questions, which aim was to evaluate knowledge on three distinct areas: six for knowledge about food fibres; six for the relation between fibres and variety of foods and 12 for the relations between fibres and diseases. The methodological study was conducted with 231 participants, from which 64.9% were female and 35.1% male, aged between 17 and 80 years. The respondents were selected by convenience, although of age, literacy, gender, geographical area of residence, including people from different cities and smaller villages. 67% of respondents consider that the consumption of sufficient amounts of fibres can prevent or treat different diseases. 85% of respondents have noted that legumes (peas, beans) are source of fibres, but more possible take up the fibre with a combination of vegetables and animal products. This research was prepared in the ambit of the multinational project from CI&DETS Research Centre (IPV e Viseu, Portugal) with reference PROJ/CI&DETS/2014/0001.

Fiber, a component for health gastrointestinal endocrine system

Dietary fiber was classified according to its solubility in an attempt to relate physiological effects to chemical types of fiber. Soluble fibers (B-glucans, gums, wheat dextrin, psyllium, pectin, inulin) were considered to have benefits on serum lipids, while insoluble fibers (cellulose, lignin, pectins, hemicelluloses) were linked with laxation benefits. More important characteristics of fiber in terms of physiological benefits are viscosity and fermentability. Viscous fibers (pectins, B-glucans, gums, psyllium) are those that have gel-forming properties in the intestinal tract, and fermentable fibers (wheat dextrin, pectins, B-glucans, gum, inulin) are those that can be metabolized by colonic bacteria. Objective: To summarize the beneficial effects of dietary fiber, as nutraceuticals, in order to maintain a healthy gastrointestinal system. Methods: Our study is a systematic review. Electronic databases, including PubMed, Medline, with supplement of relevant websites, were searched. We included randomized and non-randomized clinical trials, epidemiological studies (cohort and case-control). We excluded case series, case reports, in vitro and animal studies. Results: The WHO, the U.S. Food and Drug Administration (FDA), the Heart Foundation and the Romanian Dietary Guidelines recommends that adults should aim to consume approximately 25–30 g fiber daily. Dietary fiber is found in the indigestible parts of cereals, fruits and vegetables. There are countries where people don’t eat enough food fibers, these people need to take some kind of fiber supplement. Evidence has been found that dietary fiber from whole foods or supplements may (1) reduce the risk of cardiovascular disease by improving serum lipids and reducing serum total and low-density lipoprotein (LDL) cholesterol concentrations, (2) decreases the glycaemic index of foods, which leads to an improvement in glycemic response, positive impact on diabetes, (3) protect against development of obesity by increasing satiety hormone leptin concentrations, (4) reduced risk of developing colorectal cancer by normalizes bowel movements, improve the integrity of the epithelial layer of the intestines, increase the resistance against pathogenic colonization, have favorable effects on the gut microbiome, wich is the second genomes of the microorganisms, (5) have a positive impact on the endocrine system by gastrointestinal polypeptide hormonal regulation of digestion, (6) have prebiotic effect by short-chain fatty acids (SCFA) production; butyrate acid is the preferred energy source for colonic epithelial cells, promotes normal cell differentiation and proliferation, and also help regulate sodium and water absorption, and can enhance absorption of calcium and other minerals. Although all prebiotics are fiber, not all fiber is prebiotic. This generally refers to the ability of a fiber to increase the growth of bifidobacteria and lactobacilli, which are beneficial to human health, and (7) play a role in improving immune function via production of SCFAs by increases T helper cells, macrophages, neutrophils, and increased cytotoxic activity of natural killer cells. Conclusion: Fiber consumption is associated with high nutritional value and antioxidant status of the diet, enhancing the effects on human health. Fibers with prebiotic properties can also be recommended as part of fiber intake. Due to the variability of fiber’s effects in the body, it is important to consume fiber from a variety of sources. Increasing fiber consumption for health promotion and disease prevention is a critical public health goal.

Caffeine As An Indicator Of Estrogenic Activity In Source Water.

Caffeine has already been used as an indicator of anthropogenic impacts, especially the ones related to the disposal of sewage in water bodies. In this work, the presence of caffeine has been correlated with the estrogenic activity of water samples measured using the BLYES assay. After testing 96 surface water samples, it was concluded that caffeine can be used to prioritize samples to be tested for estrogenic activity in water quality programs evaluating emerging contaminants with endocrine disruptor activity.

Granulocyte Colony-stimulating Factor (g-csf) Positive Effects On Muscle Fiber Degeneration And Gait Recovery After Nerve Lesion In Mdx Mice.

G-CSF has been shown to decrease inflammatory processes and to act positively on the process of peripheral nerve regeneration during the course of muscular dystrophy. The aims of this study were to investigate the effects of treatment of G-CSF during sciatic nerve regeneration and histological analysis in the soleus muscle in MDX mice. Six-week-old male MDX mice underwent left sciatic nerve crush and were G-CSF treated at 7 days prior to and 21 days after crush. Ten and twenty-one days after surgery, the mice were euthanized, and the sciatic nerves were processed for immunohistochemistry (anti-p75(NTR) and anti-neurofilament) and transmission electron microscopy. The soleus muscles were dissected out and processed for H&E staining and subsequent morphologic analysis. Motor function analyses were performed at 7 days prior to and 21 days after sciatic crush using the CatWalk system and the sciatic nerve index. Both groups treated with G-CSF showed increased p75(NTR) and neurofilament expression after sciatic crush. G-CSF treatment decreased the number of degenerated and regenerated muscle fibers, thereby increasing the number of normal muscle fibers. The reduction in p75(NTR) and neurofilament indicates a decreased regenerative capacity in MDX mice following a lesion to a peripheral nerve. The reduction in motor function in the crushed group compared with the control groups may reflect the cycles of muscle degeneration/regeneration that occur postnatally. Thus, G-CSF treatment increases motor function in MDX mice. Nevertheless, the decrease in baseline motor function in these mice is not reversed completely by G-CSF.