Coupling of LMS with a fs-laser ablation ion source: elemental and isotope composition measurements

Mass spectrometric analysis of elemental and isotopic compositions of several NIST standards is performed by a miniature laser ablation/ionisation reflectron-type time-of-flight mass spectrometer (LMS) using a fs-laser ablation ion source (775 nm, 190 fs, 1 kHz). The results of the mass spectrometric studies indicate that in a defined range of laser irradiance (fluence) and for a certain number of accumulations of single laser shot spectra, the measurements of isotope abundances can be conducted with a measurement accuracy at the per mill level and at the per cent level for isotope concentrations higher and lower than 100 ppm, respectively. Also the elemental analysis can be performed with a good accuracy. The LMS instrument combined with a fs-laser ablation ion source exhibits similar detection efficiency for both metallic and non-metallic elements. Relative sensitivity coefficients were determined and found to be close to one, which is of considerable importance for the development of standard-less instruments. Negligible thermal effects, sample damage and excellent characteristics of the fs-laser beam are thought to be the main reason for substantial improvement of the instrumental performance compared to other laser ablation mass spectrometers.

Performance evaluation of a miniature laser ablation time-of-flight mass spectrometer designed for in situ investigations in planetary space research

Key performance features of a miniature laser ablation time-of-flight mass spectrometer designed for in situ investigations of the chemical composition of planetary surfaces are presented. This mass spectrometer is well suited for elemental and isotopic analysis of raw solid materials with high sensitivity and high spatial resolution. In this study, ultraviolet laser radiation with irradiances suitable for ablation (< 1 GW/cm2) is used to achieve stable ion formation and low sample consumption. In comparison to our previous laser ablation studies at infrared wavelengths, several improvements to the experimental setup have been made, which allow accurate control over the experimental conditions and good reproducibility of measurements. Current performance evaluations indicate significant improvements to several instrumental figures of merit. Calibration of the mass scale is performed within a mass accuracy (Δm/m) in the range of 100 ppm, and a typical mass resolution (m/Δm) ~600 is achieved at the lead mass peaks. At lower laser irradiances, the mass resolution is better, about (m/Δm) ~900 for lead, and limited by the laser pulse duration of 3 ns. The effective dynamic range of the instrument was enhanced from about 6 decades determined in previous study up to more than 8 decades at present. Current studies show high sensitivity in detection of both metallic and non-metallic elements. Their abundance down to tens of ppb can be measured together with their isotopic patterns. Due to strict control of the experimental parameters, e.g. laser characteristics, ion-optical parameters and sample position, by computer control, measurements can be performed with high reproducibility. Copyright © 2012 John Wiley & Sons, Ltd.

Academic medical centers: A framework for strategic repositioning

This study sought to understand the elements affecting the success or failure of strategic repositioning efforts by academic medical centers (AMC). The research question was: What specific elements in the process appear to be most important in determining the success or failure of an AMC.s strategic repositioning? Where success is based on the longterm sustainability of the new position.^ "An organization's strategic position is its perceptual location relative to others" (Gershon, 2003). Hence, strategic repositioning represents a shift from one strategic position within an environment to another (H. Mintzberg, 1987a). A deteriorating value proposition coupled with an unsustainable national health care financing system is forcing AMCs to change their strategic position. Where the value proposition is defined as the health outcome per dollar spent. ^ AMCs are of foundational importance to our health care system. They educate our new physicians, generate significant scientific breakthroughs, and care for our most difficult patients. Yet, their strategic, financial and business acumen leaves them particularly vulnerable in a changing environment. ^ After a literature review revealed limited writing on this subject, the research question was addressed using three separate but parallel exploratory case study inquiries of AMCs that recently underwent a strategic repositioning. Participating in the case studies were the Baylor College of Medicine, the University of Texas M. D. Anderson Cancer Center, and the University of Texas Medical Branch.^ Each case study consisted of two major research segments; a thorough documentation review followed by semi-structured interviews of selected members of their governance board, executive and faculty leadership teams. While each case study.s circumstances varied, their response to the research question, as extracted through thematic coding and analysis of the interviews, had a high degree of commonality.^ The results identified managing the strategic risk surrounding the repositioning and leadership accountability as the two foundational elements of success or failure. Metrics and communication were important process elements. They both play a major role in managing the strategic repositioning risk communication loop. Sustainability, the final element, was the outcome sought.^ Factors leading to strategic repositioning included both internal and external pressures and were primarily financial or mission based. Timing was an important consideration as was the selection of the strategic repositioning endpoint.^ In conclusion, a framework for the strategic repositioning of AMCs was offered that integrates the findings of this study; the elements of success, the factors leading to strategic repositioning, and the risk communication loop. ^

Sobre la Diosa Siria o un posible regreso a casa de Luciano de Samosata

La obra titulada Sobre la diosa siria forma parte, en la tradición manuscrita, del corpus de Luciano de Samosata. Se ha discutido, sin embargo, su autoría: mientras algunos encuentran elementos claros no propios de Luciano, otros no ven en ellos pruebas concluyentes, dado el carácter siempre escurridizo del samosatense. Partiendo del supuesto de que se trata de una obra de Luciano -o, en cualquier caso, de un sirio helenizado de época imperial-, el análisis de lo descrito, de la propia narración, de la lengua utilizada y de la enunciación del narrador, aportan, sin duda, información valiosa a propósito del choque y de la fusión de culturas en el imperio romano.

Sobre la Diosa Siria o un posible regreso a casa de Luciano de Samosata

La obra titulada Sobre la diosa siria forma parte, en la tradición manuscrita, del corpus de Luciano de Samosata. Se ha discutido, sin embargo, su autoría: mientras algunos encuentran elementos claros no propios de Luciano, otros no ven en ellos pruebas concluyentes, dado el carácter siempre escurridizo del samosatense. Partiendo del supuesto de que se trata de una obra de Luciano -o, en cualquier caso, de un sirio helenizado de época imperial-, el análisis de lo descrito, de la propia narración, de la lengua utilizada y de la enunciación del narrador, aportan, sin duda, información valiosa a propósito del choque y de la fusión de culturas en el imperio romano.

Sobre la Diosa Siria o un posible regreso a casa de Luciano de Samosata

La obra titulada Sobre la diosa siria forma parte, en la tradición manuscrita, del corpus de Luciano de Samosata. Se ha discutido, sin embargo, su autoría: mientras algunos encuentran elementos claros no propios de Luciano, otros no ven en ellos pruebas concluyentes, dado el carácter siempre escurridizo del samosatense. Partiendo del supuesto de que se trata de una obra de Luciano -o, en cualquier caso, de un sirio helenizado de época imperial-, el análisis de lo descrito, de la propia narración, de la lengua utilizada y de la enunciación del narrador, aportan, sin duda, información valiosa a propósito del choque y de la fusión de culturas en el imperio romano.

Major and minor element concentrations in the livers of polar bears (Ursus maritimus) from Greenland, Canada and Alaska

To assess geographic distributions of elements in the Arctic we compared essential and non-essential elements in the livers of polar bears (Ursus maritimus) collected from five regions within Canada in 2002, in Alaska between 1994 and 1999 and from the northwest and east coasts of Greenland between 1988 and 2000. As, Hg, Pb and Se varied with age, and Co and Zn with gender, which limited spatial comparisons across all populations to Cd, which was highest in Greenland bears. Collectively, geographic relationships appeared similar to past studies with little change in concentration over time in Canada and Greenland for most elements; Hg and Se were higher in some Canadian populations in 2002 as compared to 1982 and 1984. Concentrations of most elements in the polar bears did not exceed toxicity thresholds, although Cd and Hg exceeded levels correlated with the formation of hepatic lesions in laboratory animals.

Vector spaces of entire functions of unbounded type

Let E be an infinite dimensional complex Banach space. We prove the existence of an infinitely generated algebra, an infinite dimensional closed subspace and a dense subspace of entire functions on E whose non-zero elements are functions of unbounded type. We also show that the τδ topology on the space of all holomorphic functions cannot be obtained as a countable inductive limit of Fr´echet spaces. RESUMEN. Sea E un espacio de Banach complejo de dimensión infinita y sea H(E) el espacio de funciones holomorfas definidas en E. En el artículo se demuestra la existencia de un álgebra infinitamente generada en H(E), un subespacio vectorial en H(E) cerrado de dimensión infinita y un subespacio denso en H(E) cuyos elementos no nulos son funciones de tipo no acotado. También se demuestra que el espacio de funciones holomorfas con la topología ? no es un límite inductivo numberable de espacios de Fréchet.

Corporate social responsibility in portfolio selection: A "goal games" against nature approach

Nowadays, there is an uprising social pressure on big companies to incorporate into their decision-making process elements of the so-called social responsibility. Among the many implications of this fact, one relevant one is the need to include this new element in classic portfolio selection models. This paper meets this challenge by formulating a model that combines goal programming with "goal games" against nature in a scenario where the social responsibility is defined through the introduction of a battery of sustainability indicators amalgamated into a synthetic index. In this way, we have obtained an efficient model that only implies solving a small number of linear programming problems. The proposed approach has been tested and illustrated by using a case study related to the selection of securities in international markets.

New methods for the synthesis of radiation patterns of coupled antenna arrays = Nuevos métodos de síntesis de diagramas de radiación de agrupaciones de antenas acopladas

El principal objetivo de esta tesis es el desarrollo de métodos de síntesis de diagramas de radiación de agrupaciones de antenas, en donde se realiza una caracterización electromagnética rigurosa de los elementos radiantes y de los acoplos mutuos existentes. Esta caracterización no se realiza habitualmente en la gran mayoría de métodos de síntesis encontrados en la literatura, debido fundamentalmente a dos razones. Por un lado, se considera que el diagrama de radiación de un array de antenas se puede aproximar con el factor de array que únicamente tiene en cuenta la posición de los elementos y las excitaciones aplicadas a los mismos. Sin embargo, como se mostrará en esta tesis, en múltiples ocasiones un riguroso análisis de los elementos radiantes y del acoplo mutuo entre ellos es importante ya que los resultados obtenidos pueden ser notablemente diferentes. Por otro lado, no es sencillo combinar un método de análisis electromagnético con un proceso de síntesis de diagramas de radiación. Los métodos de análisis de agrupaciones de antenas suelen ser costosos computacionalmente, ya que son estructuras grandes en términos de longitudes de onda. Generalmente, un diseño de un problema electromagnético suele comprender varios análisis de la estructura, dependiendo de las variaciones de las características, lo que hace este proceso muy costoso. Dos métodos se utilizan en esta tesis para el análisis de los arrays acoplados. Ambos están basados en el método de los elementos finitos, la descomposición de dominio y el análisis modal para analizar la estructura radiante y han sido desarrollados en el grupo de investigación donde se engloba esta tesis. El primero de ellos es una técnica de análisis de arrays finitos basado en la aproximación de array infinito. Su uso es indicado para arrays planos de grandes dimensiones con elementos equiespaciados. El segundo caracteriza el array y el acoplo mutuo entre elementos a partir de una expansión en modos esféricos del campo radiado por cada uno de los elementos. Este método calcula los acoplos entre los diferentes elementos del array usando las propiedades de traslación y rotación de los modos esféricos. Es capaz de analizar agrupaciones de elementos distribuidos de forma arbitraria. Ambas técnicas utilizan una formulación matricial que caracteriza de forma rigurosa el campo radiado por el array. Esto las hace muy apropiadas para su posterior uso en una herramienta de diseño, como los métodos de síntesis desarrollados en esta tesis. Los resultados obtenidos por estas técnicas de síntesis, que incluyen métodos rigurosos de análisis, son consecuentemente más precisos. La síntesis de arrays consiste en modificar uno o varios parámetros de las agrupaciones de antenas buscando unas determinadas especificaciones de las características de radiación. Los parámetros utilizados como variables de optimización pueden ser varios. Los más utilizados son las excitaciones aplicadas a los elementos, pero también es posible modificar otros parámetros de diseño como son las posiciones de los elementos o las rotaciones de estos. Los objetivos de las síntesis pueden ser dirigir el haz o haces en una determinada dirección o conformar el haz con formas arbitrarias. Además, es posible minimizar el nivel de los lóbulos secundarios o del rizado en las regiones deseadas, imponer nulos que evitan posibles interferencias o reducir el nivel de la componente contrapolar. El método para el análisis de arrays finitos basado en la aproximación de array infinito considera un array finito como un array infinito con un número finito de elementos excitados. Los elementos no excitados están físicamente presentes y pueden presentar tres diferentes terminaciones, corto-circuito, circuito abierto y adaptados. Cada una de estas terminaciones simulará mejor el entorno real en el que el array se encuentre. Este método de análisis se integra en la tesis con dos métodos diferentes de síntesis de diagramas de radiación. En el primero de ellos se presenta un método basado en programación lineal en donde es posible dirigir el haz o haces, en la dirección deseada, además de ejercer un control sobre los lóbulos secundarios o imponer nulos. Este método es muy eficiente y obtiene soluciones óptimas. El mismo método de análisis es también aplicado a un método de conformación de haz, en donde un problema originalmente no convexo (y de difícil solución) es transformado en un problema convexo imponiendo restricciones de simetría, resolviendo de este modo eficientemente un problema complejo. Con este método es posible diseñar diagramas de radiación con haces de forma arbitraria, ejerciendo un control en el rizado del lóbulo principal, así como en el nivel de los lóbulos secundarios. El método de análisis de arrays basado en la expansión en modos esféricos se integra en la tesis con tres técnicas de síntesis de diagramas de radiación. Se propone inicialmente una síntesis de conformación del haz basado en el método de la recuperación de fase resuelta de forma iterativa mediante métodos convexos, en donde relajando las restricciones del problema original se consiguen unas soluciones cercanas a las óptimas de manera eficiente. Dos métodos de síntesis se han propuesto, donde las variables de optimización son las posiciones y las rotaciones de los elementos respectivamente. Se define una función de coste basada en la intensidad de radiación, la cual es minimizada de forma iterativa con el método del gradiente. Ambos métodos reducen el nivel de los lóbulos secundarios minimizando una función de coste. El gradiente de la función de coste es obtenido en términos de la variable de optimización en cada método. Esta función de coste está formada por la expresión rigurosa de la intensidad de radiación y por una función de peso definida por el usuario para imponer prioridades sobre las diferentes regiones de radiación, si así se desea. Por último, se presenta un método en el cual, mediante técnicas de programación entera, se buscan las fases discretas que generan un diagrama de radiación lo más cercano posible al deseado. Con este método se obtienen diseños que minimizan el coste de fabricación. En cada uno de las diferentes técnicas propuestas en la tesis, se presentan resultados con elementos reales que muestran las capacidades y posibilidades que los métodos ofrecen. Se comparan los resultados con otros métodos disponibles en la literatura. Se muestra la importancia de tener en cuenta los diagramas de los elementos reales y los acoplos mutuos en el proceso de síntesis y se comparan los resultados obtenidos con herramientas de software comerciales. ABSTRACT The main objective of this thesis is the development of optimization methods for the radiation pattern synthesis of array antennas in which a rigorous electromagnetic characterization of the radiators and the mutual coupling between them is performed. The electromagnetic characterization is usually overlooked in most of the available synthesis methods in the literature, this is mainly due to two reasons. On the one hand, it is argued that the radiation pattern of an array is mainly influenced by the array factor and that the mutual coupling plays a minor role. As it is shown in this thesis, the mutual coupling and the rigorous characterization of the array antenna influences significantly in the array performance and its computation leads to differences in the results obtained. On the other hand, it is difficult to introduce an analysis procedure into a synthesis technique. The analysis of array antennas is generally expensive computationally as the structure to analyze is large in terms of wavelengths. A synthesis method requires to carry out a large number of analysis, this makes the synthesis problem very expensive computationally or intractable in some cases. Two methods have been used in this thesis for the analysis of coupled antenna arrays, both of them have been developed in the research group in which this thesis is involved. They are based on the finite element method (FEM), the domain decomposition and the modal analysis. The first one obtains a finite array characterization with the results obtained from the infinite array approach. It is specially indicated for the analysis of large arrays with equispaced elements. The second one characterizes the array elements and the mutual coupling between them with a spherical wave expansion of the radiated field by each element. The mutual coupling is computed using the properties of translation and rotation of spherical waves. This method is able to analyze arrays with elements placed on an arbitrary distribution. Both techniques provide a matrix formulation that makes them very suitable for being integrated in synthesis techniques, the results obtained from these synthesis methods will be very accurate. The array synthesis stands for the modification of one or several array parameters looking for some desired specifications of the radiation pattern. The array parameters used as optimization variables are usually the excitation weights applied to the array elements, but some other array characteristics can be used as well, such as the array elements positions or rotations. The desired specifications may be to steer the beam towards any specific direction or to generate shaped beams with arbitrary geometry. Further characteristics can be handled as well, such as minimize the side lobe level in some other radiating regions, to minimize the ripple of the shaped beam, to take control over the cross-polar component or to impose nulls on the radiation pattern to avoid possible interferences from specific directions. The analysis method based on the infinite array approach considers an infinite array with a finite number of excited elements. The infinite non-excited elements are physically present and may have three different terminations, short-circuit, open circuit and match terminated. Each of this terminations is a better simulation for the real environment of the array. This method is used in this thesis for the development of two synthesis methods. In the first one, a multi-objective radiation pattern synthesis is presented, in which it is possible to steer the beam or beams in desired directions, minimizing the side lobe level and with the possibility of imposing nulls in the radiation pattern. This method is very efficient and obtains optimal solutions as it is based on convex programming. The same analysis method is used in a shaped beam technique in which an originally non-convex problem is transformed into a convex one applying symmetry restrictions, thus solving a complex problem in an efficient way. This method allows the synthesis of shaped beam radiation patterns controlling the ripple in the mainlobe and the side lobe level. The analysis method based on the spherical wave expansion is applied for different synthesis techniques of the radiation pattern of coupled arrays. A shaped beam synthesis is presented, in which a convex formulation is proposed based on the phase retrieval method. In this technique, an originally non-convex problem is solved using a relaxation and solving a convex problems iteratively. Two methods are proposed based on the gradient method. A cost function is defined involving the radiation intensity of the coupled array and a weighting function that provides more degrees of freedom to the designer. The gradient of the cost function is computed with respect to the positions in one of them and the rotations of the elements in the second one. The elements are moved or rotated iteratively following the results of the gradient. A highly non-convex problem is solved very efficiently, obtaining very good results that are dependent on the starting point. Finally, an optimization method is presented where discrete digital phases are synthesized providing a radiation pattern as close as possible to the desired one. The problem is solved using linear integer programming procedures obtaining array designs that greatly reduce the fabrication costs. Results are provided for every method showing the capabilities that the above mentioned methods offer. The results obtained are compared with available methods in the literature. The importance of introducing a rigorous analysis into the synthesis method is emphasized and the results obtained are compared with a commercial software, showing good agreement.

An evaluation of the performance of cDNA microarrays for detecting changes in global mRNA expression

The cDNA microarray is one technological approach that has the potential to accurately measure changes in global mRNA expression levels. We report an assessment of an optimized cDNA microarray platform to generate accurate, precise and reliable data consistent with the objective of using microarrays as an acquisition platform to populate gene expression databases. The study design consisted of two independent evaluations with 70 arrays from two different manufactured lots and used three human tissue sources as samples: placenta, brain and heart. Overall signal response was linear over three orders of magnitude and the sensitivity for any element was estimated to be 2 pg mRNA. The calculated coefficient of variation for differential expression for all non-differentiated elements was 12–14% across the entire signal range and did not vary with array batch or tissue source. The minimum detectable fold change for differential expression was 1.4. Accuracy, in terms of bias (observed minus expected differential expression ratio), was less than 1 part in 10 000 for all non-differentiated elements. The results presented in this report demonstrate the reproducible performance of the cDNA microarray technology platform and the methods provide a useful framework for evaluating other technologies that monitor changes in global mRNA expression.

Wrestling With Tradition: Japanese Activities at Amache, a World War II Incarceration Facility

I employ archaeological analyses, archival research, and oral histories to investigate traditional Japanese practices that were performed at Amache, a World War II Japanese American incarceration facility. I argue that these inter-generational practices helped to bridge a cultural gap that existed between several generations of Japanese Americans. For many incarcerated Japanese Americans, their first exposure to many traditional activities occurred during incarceration. The resulting social environment incorporated aspects of Japanese, Japanese American, and mainstream American influences, all of which were adapted to conditions during incarceration. Similarly, archaeological analyses allow for the investigation of traditional practice features. These provide evidence regarding the significance of the adapted landscape at Amache. Evidence of these practices suggests Amache internees had both a strong desire to maintain and celebrate these aspects of their Japanese heritage but they also incorporated non-traditional elements that reflected the unique living conditions during incarceration. Incarceration, I argue, created an environment in which a unique internee consciousness was formed in which the use of traditional practices was a focal point. The physical remains of traditional practices allow archaeologists to determine aspects of this newly formed consciousness that are not readily apparent in historical documentation.

Evaluation of the multi-element capabilities of collision/reaction cell inductively coupled plasma - mass spectrometry in wine analysis

This work explores the multi-element capabilities of inductively coupled plasma - mass spectrometry with collision/reaction cell technology (CCT-ICP-MS) for the simultaneous determination of both spectrally interfered and non-interfered nuclides in wine samples using a single set of experimental conditions. The influence of the cell gas type (i.e. He, He+H2 and He+NH3), cell gas flow rate and sample pre-treatment (i.e. water dilution or acid digestion) on the background-equivalent concentration (BEC) of several nuclides covering the mass range from 7 to 238 u has been studied. Results obtained in this work show that, operating the collision/reaction cell with a compromise cell gas flow rate (i.e. 4 mL min−1) improves BEC values for interfered nuclides without a significant effect on the BECs for non-interfered nuclides, with the exception of the light elements Li and Be. Among the different cell gas mixtures tested, the use of He or He+H2 is preferred over He+NH3 because NH3 generates new spectral interferences. No significant influence of the sample pre-treatment methodology (i.e. dilution or digestion) on the multi-element capabilities of CCT-ICP-MS in the context of simultaneous analysis of interfered and non-interfered nuclides was observed. Nonetheless, sample dilution should be kept at minimum to ensure that light nuclides (e.g. Li and Be) could be quantified in wine. Finally, a direct 5-fold aqueous dilution is recommended for the simultaneous trace and ultra-trace determination of spectrally interfered and non-interfered elements in wine by means of CCT-ICP-MS. The use of the CCT is mandatory for interference-free ultra-trace determination of Ti and Cr. Only Be could not be determined when using the CCT due to a deteriorated limit of detection when compared to conventional ICP-MS.

A treatise on chemistry,

I. The non-meallic elements.--II.The metals.--III. The chemistry of the hydrocarbons and their derivatives, or Organic chemistry: pt. I; Pt. II; pt. III; pt. IV 1892; pt. V; pt. VI.

A treatise on chemistry,

Vol. I: 1st edition, 1877; 5th edition, 1920. Vol. II: 1st edition, 1878; 6th edition, 1923.