Enhancement of ultrafiltration process by pretreatment in recovery of hemicelluloses from wood extracts

Hemicelluloses are potential raw material for several items produced in future wood-based biorefineries. One possible method for recovering hemicelluloses from wood extracts is ultrafiltration (UF). However, low filtration capacities and severe fouling restrict the use of tight UF membranes in the treatment of wood extracts. The lack of suitable commercial membranes creates a need for pretreatment which would decrease fouling and increase the filtration capacity. This thesis focuses on the evaluation of the possibility to improve the filtration capacity and decrease fouling with the pretreatment of wood extracts. Methods which remove harmful compounds and methods which degrade them are studied, as well as combinations of the methods. The tested pretreatments have an influence on both the concentration of different compounds and the molecular mass distribution of the compounds in the extract. This study revealed that in addition to which kind of compounds were removed, also the change in molecular size distribution affected the filtration capacity significantly. It was shown that the most harmful compounds for the filtration capacity of the hydrophobic 5 kDa membrane were the ones capable of permeating the membrane and fouling also the inner membrane structure. Naturally, the size of the most harmful compounds depends on the used UF membrane and is thus case-specific. However, in the choice of the pretreatment method, the focus should be on the removal of harmful compound sizes rather than merely on the total amount of removed foulants. The results proved that filtration capacity can be increased with both adsorptive and oxidative pretreatments even by hundreds of per cents. For instance, the use of XAD7 and XAD16 adsorbents increased the average flux in the UF of a birch extract from nearly zero to 107 kg/(m2h) and 175 kg/(m2h), respectively. In the treatment of a spruce extract, oxidation by pulsed corona discharge (PCD) increased the flux in UF from 46 kg/(m2h) to 158 kg/(m2h). Moreover, when a birch extract batch was treated with laccase enzyme, the flux in UF increased from 15 kg/(m2h) to 36 kg/(m2h). However, fouling was decreased only by adsorptive pretreatment while oxidative methods had a negligible or even negative impact on it. This demonstrates that filtration capacity and fouling are affected by different compounds and mechanisms. The results of this thesis show that filtration capacity can be improved and fouling decreased through appropriate pretreatment. However, the choice of the best possible pretreatment is case-specific and depends on the wood extract and the membrane used. Finding the best option requires information on the extract content and membrane characteristics as well as on the filtration performance of the membrane in the prevailing conditions and a multivariate approach. On the basis of this study, it can be roughly concluded that adsorptive pretreatment improves the filtration capacity and decreases fouling rather reliably, but it may lead to significant hemicellulose losses. Oxidation reduces the loss of valuable hemicelluloses and could improve the filtration capacity, but fouling challenges may remain. Combining oxidation with adsorptive pretreatment was not a solution for avoiding hemicellulose losses in the tested cases.

The characterization of new benzimidazole fungicides /

Extensive studies have been initiated to generate enough data to register the methyl homologue (MBC-MIC, see List of Abbreviations, page 14) of benomyl (MBC-BIC) as a commercial product through a joint effort between the federal government and Canadian industry. The objective of this study, as part of the whole project, was to generate fundamental data on the physical properties of the series of benomyl homologues (MBC-MIC, MBC-EIC, MBC-PIC and MBC-BIC). These data include the half lives of these compounds in water at the pH range from 2 to 12; they ranged from 0.7 to 10. 1 hours. Standard solutions of these compounds in concentrated acid were found to be stable for at least two weeks, and in the case of MBC-MIC it was stable at least 1 month. Another major goal of this study was to determine the solubility of each compound in water at different pHs in the range of 1 to 12. The solubility of the compounds ranged from 0.6 jig/mL to 396 fig/mL. In addition, it was possible to prepare stable stock solutions at concentrations > 1 000 |ig/mL in concentrated nitric acid. Several aspects of analytical methods have been improved to accurately assess the solubility and rate of degradation of benomyl and its homologues in alkaline conditions. The determination of melting points was attempted but all compounds decomposed before melting.To complement the studies of the benomyl homologue series attempts were made to explore the presence of any relationships between the structures of the compounds and their properties. Although there were some exceptions, the compound's solubility decreased and half life increased as the molecular size increased from the methyl to the butyl analogue.

Synthesis of dimethyl acetal of ketones: design of solid acid catalysts for one-pot acetalization reaction

The synthesis of dimethyl acetals of carbonyl compounds such as cyclohexanone, acetophenone, and benzophenone has successfully been carried out by the reaction between ketones and methanol using different solid acid catalysts. The strong influence of the textural properties of the catalysts such as acid amount and adsorption properties (surface area and pore volume) determine the catalytic activity. The molecular size of the reactants and products determine the acetalization ability of a particular ketone. The hydrophobicity of the various rare earth exchanged Mg–Y zeolites, K-10 montmorillonite clay, and cerium exchanged montmorillonite (which shows maximum activity) is more determinant than the number of active sites present on the catalyst. The optimum number of acidic sites as well as dehydrating ability of Ce3+-montmorillonite and K-10 montmorillonite clays and various rare earth exchanged Mg–Y zeolites seem to work well in shifting the equilibrium to the product side.

Stress relaxation behavior of wheat dough, gluten, and gluten protein fractions

Relaxation behavior was measured for dough, gluten and gluten protein fractions obtained from the U.K. biscuitmaking flour, Riband, and the U.K. breadmaking flour, Hereward. The relaxation spectrum, in which relaxation times (tau) are related to polymer molecular size, for dough showed a broad molecular size distribution, with two relaxation processes: a major peak at short times and a second peak at times longer than 10 sec, which is thought to correspond to network structure, and which may be attributed to entanglements and physical cross-links of polymers. Relaxation spectra of glutens were similar to those for the corresponding doughs from both flours. Hereward gluten clearly showed a much more pronounced second peak in relaxation spectrum and higher relaxation modulus than Riband gluten at the same water content. In the gluten protein fractions, gliadin and acetic acid soluble glutenin only showed the first relaxation process, but gel protein clearly showed both the first and second relaxation processes. The results show that the relaxation properties of dough depend on its gluten protein and that gel protein is responsible for the network structure for dough and gluten.

Synthesis of isomaltooligosaccharides and oligodextrans by the combined use of dextransucrase and dextranase

Batch syntheses of isomaltooligosaccharides (IMO) from sucrose, using the enzymes dextransucrase and dextranase were performed with the aim of understanding the reaction mechanism and the parameters which affect product characteristics and molecular size. Both activities described for dextransucrase (dextran formation and acceptor reaction) achieved synthesis whilst the hydrolytic activity of dextranase regulated the product molecular size and acceptor availability. Depending on the reaction conditions, the product oligosaccharide mixtures contained mainly sugars (up to 36%) with degrees of polymerization (DP) varying between 10 and 60 together with lower concentrations of both lower and higher molecular weight sugars. Alterations in substrate and dextranase concentrations (50-400 mg ml(-1) and 2.5-46 U ml(-1), respectively) affected the molecular weight of IMO, the reaction rate and the formation of leucrose. This permitted manipulation of the product characteristics. It was found that higher substrate and dextranase concentrations gave rise to products with lower molecular sizes and a dextransucrase:dextranase ratio of 1: 1 or 1:2 appeared to produce a polymer with a molecular weight which is desirable for prebiotic use. (C) 2004 Elsevier Inc. All rights reserved.

Rheology and the breadmaking process

The applications of rheology to the main processes encountered during breadmaking (mixing, sheeting, fermentation and baking) are reviewed. The most commonly used rheological test methods and their relationships to product functionality are reviewed. It is shown that the most commonly used method for rheological testing of doughs, shear oscillation dynamic rheology, is generally used under deformation conditions inappropriate for breadmaking and shows little relationship with end-use performance. The frequency range used in conventional shear oscillation tests is limited to the plateau region, which is insensitive to changes in the HMW glutenin polymers thought to be responsible for variations in baking quality. The appropriate deformation conditions can be accessed either by long-time creep or relaxation measurements, or by large deformation extensional measurements at low strain rates and elevated temperatures. Molecular size and structure of the gluten polymers that make up the major structural components of wheat are related to their rheological properties via modern polymer rheology concepts. Interactions between polymer chain entanglements and branching are seen to be the key mechanisms determining the rheology of HMW polymers. Recent work confirms the observation that the dynamic shear plateau modulus is essentially independent of variations in MW of glutens amongst wheat varieties of varying baking performance and also that it is not the size of the soluble glutenin polymers, but the secondary structural and rheological properties of the insoluble polymer fraction that are mainly responsible for variations in baking performance. Extensional strain hardening has been shown to be a sensitive indicator of entanglements and long-chain branching in HMW polymers, and is well related to baking performance of bread doughs. The Considere failure criterion for instability in extension of polymers defines a region below which bubble walls become unstable, and predicts that when strain hardening falls below a value of around 1, bubble walls are no longer stable and coalesce rapidly, resulting in loss of gas retention and lower volume and texture. Strain hardening in doughs has been shown to reach this value at increasingly higher temperatures for better breadmaking varieties and is directly related to bubble stability and baking performance. (C) 2003 Elsevier Ltd. All rights reserved.

The effect of condensed tannins in fresh sainfoin (Onobrychis viciifolia) on in vivo and in situ digestion in sheep

This study focused on effects of structure, content and biological activity of condensed tannins (CT) in leaves, stems and whole plant of sainfoin (Onobrychis viciifolia) on its in vivo and in situ digestive characteristics in sheep. Sainfoin was studied as fresh forage during the first vegetation cycle at two phenological stages (i.e., end of flowering and green seeds) and during the second vegetation cycle (i.e., start of flowering). The feeding experiment used 12 sheep; with six dosed, through the rumen cannula, with polyethylene glycol (PEG) to neutralise CT effects. Organic matter digestibility (OMD), total tract N disappearance and N balance were measured in sheep fed the whole plant. The residues of dry matter (DM) and N from nylon bags suspended in the rumen were determined on leaves and stems. Intestinal digestibility was measured using other, intestinally fistulated sheep. PEG addition and vegetation cycle increased total tract N digestibility (P<0.001) but PEG affected OMD only at the end of flowering. PEG inactivated the CT and increased urinary N excretion (P<0.05) but this was offset by lower faecal N excretion (P<0.001). Feeding sainfoin can be used to alter the form of excreted N (i.e., urine vs faeces) and thus potentially reduce environmental N pollution without affecting body N retention. Kinetic studies of total N, ammonia N (NH3-N) and volatile fatty acids (VFA) in rumen fluid were made before and 1.5, 3 and 6 h after feeding. Sainfoin CT decreased rumen fluid soluble N (P<0.05) and NH3-N (P<0.01). Ruminal N disappearance (DisN) of leaves or stems was lower in the presence of active CT compared to PEG-inactivated CT (P<0.001) for both vegetation cycles. PEG also increased intestinal digestibility (P<0.05) of leaves and stems. Leaves had lower ruminal DisN, but higher N disappearing from intestine than stems. The biological activity and content of CT in the whole plant decreased as phenological stage increased. Prodelphinidin:procyanidin (PD:PC) ratios of leaves varied with vegetation cycle and phenological stage. The molecular size of CT in the whole plant, as indicated by their mean degree of polymerisation (mDP), was lowest at the start of flowering and coincided with the higher biological activity and content of CT.

Separation of oligosaccharides from caprine milk whey, prior to prebiotic evaluation

Milk oligosaccharides are believed to have beneficial biological properties. Caprine milk has a relatively high concentration of oligosaccharides in comparison to other ruminant milks and has the closest oligosaccharide profile to human milk. The first stage in recovering oligosaccharides from caprine milk whey, a by-product of cheese making, was accomplished by ultrafiltration to remove proteins and fat globules, leaving more than 97% of the initial carbohydrates, mainly lactose, in the permeate. The ultrafiltered permeate was further processed using a 1 kDa ‘tight’ ultrafiltration membrane, which retained less than 7% of the remaining lactose. The final retentate was fractionated by preparative scale molecular size exclusion chromatography, to yield 28 fractions, of which oligosaccharide-rich fractions were detected somewhere between fractions 9/10 to 16/17, suitable for functionality and gut health promotion testing. All fractions were evaluated for their oligosaccharide and carbohydrate profiles using three complementary analytical methods.

Galloylated proanthocyanidins from shea (Vitellaria paradoxa) meal have potent anthelmintic activity against Ascaris suum

Proanthocyanidins (PA) from shea (Vitellaria paradoxa) meal were investigated by thiolytic degradation with benzyl mercaptan and the reaction products were analysed by high performance liquid chromatography–mass spectrometry. These PA were galloylated (≈40%), contained only B-type linkages and had a high proportion of prodelphinidins (>70%). The mean degree of polymerisation was 8 (i.e. average molecular size was 2384 Da) and epigallocatechin gallate (EGCg) was the major flavan-3-ol subunit in PA. Shea meal also proved to be a potentially valuable source for extracting free flavan-3-ol-O-gallates, especially EGCg (575 mg/kg meal), which is known for its health and anti-parasitic benefits. Proanthocyanidins were isolated and tested for bioactivity against Ascaris suum, which is an important parasite of pigs. Migration and motility tests revealed that these PA have potent activity against this parasitic nematode.

Susceptible-infected-recovered and susceptible-exposed-infected models

Two stochastic epidemic lattice models, the susceptible-infected-recovered and the susceptible-exposed-infected models, are studied on a Cayley tree of coordination number k. The spreading of the disease in the former is found to occur when the infection probability b is larger than b(c) = k/2(k - 1). In the latter, which is equivalent to a dynamic site percolation model, the spreading occurs when the infection probability p is greater than p(c) = 1/(k - 1). We set up and solve the time evolution equations for both models and determine the final and time-dependent properties, including the epidemic curve. We show that the two models are closely related by revealing that their relevant properties are exactly mapped into each other when p = b/[k - (k - 1) b]. These include the cluster size distribution and the density of individuals of each type, quantities that have been determined in closed forms.

Complex networks analysis of manual and machine translations

Complex networks have been increasingly used in text analysis, including in connection with natural language processing tools, as important text features appear to be captured by the topology and dynamics of the networks. Following previous works that apply complex networks concepts to text quality measurement, summary evaluation, and author characterization, we now focus on machine translation (MT). In this paper we assess the possible representation of texts as complex networks to evaluate cross-linguistic issues inherent in manual and machine translation. We show that different quality translations generated by NIT tools can be distinguished from their manual counterparts by means of metrics such as in-(ID) and out-degrees (OD), clustering coefficient (CC), and shortest paths (SP). For instance, we demonstrate that the average OD in networks of automatic translations consistently exceeds the values obtained for manual ones, and that the CC values of source texts are not preserved for manual translations, but are for good automatic translations. This probably reflects the text rearrangements humans perform during manual translation. We envisage that such findings could lead to better NIT tools and automatic evaluation metrics.

Investigation of interfacial processes at tetraruthenated zinc porphyrin films using electrochemical surface plasmon resonance and electrochemical quartz crystal microbalance

In the present work we describe the investigation of interfacial and superficial processes on tetraruthenated zinc porphyrin (ZnTRP) films immobilized on gold electrode surface. In situ and real time measurements employing electrochemical surface plasmon resonance (ESPR)and electrochemical quartz crystal microbalance (EQCM) have given new insights into the electrochemical oxidation of ferrocyanide and phenolic compounds (acetaminophen, dopamine, and catechol) on ZnTRP modified electrodes. The decrease of diode like behavior in the presence of such phenolic species in contrast with ferrocyanide was clearly assigned to the inclusion of those species in the porphyrin film, creating new conduction pathways connecting the gold electrode surface with the film/solution interface. In fact, there are evidences that they can intercalate in the film (catechol > dopamine > acetaminophen), whereas ferrocyanide is completely excluded. Accordingly, the molecular size may play a fundamental role in such a process. (C) 2009 Published by Elsevier Ltd.

Macroscale chromatography in the classroom

This paper describes how a simple macroscopic working model can be constructed to demonstrate the operation of chromatography in the classroom. Since the resources for construction may vary from school to school, the effect of varying 'molecular size'and packing parameter on the operation of the'chromatography column'have been investigated to provide guidance for teachers in the selection of materials to construct your own macroscopic chromatography column. Macroscopic working models help students make the link between the macroscopic observables e.g. retention time) and the conceptual explanations of the phenomenon at the microscopic level, thus helping to overcome most of the confusion and misconceptions associated with chromatography.The column is effective because it can engage kineastic, visual and auditory learning modes.The working model presented here separates components on the basis of size; other models, which separate by shape, mass, type of material, etc, are also mentioned.

Purificação e caracterização parcial de uma Fucana C de Dictyota mentrualis e estudo do seu efeito antiinflamatório e nociceptivo

In recent years, sulfated polysaccharides from marine algae have emerged as an important class of natural biopolymers with potential application in human and veterinary health care, while taking advantage of the absence of potential risk of contamination by animal viruses. Among these, fucans isolated from the cell walls of marine brown alga have been study due to their anticoagulant, antithrombotic, anti-inflammatory and antiviral activities. These biological effects of fucans have been found to depend on the degree of sulfation and molecular size of the polysaccharide chains. In the present study, we examined structural features of a fucan extracted from brown alga Dictyota menstrualis and its effect on the leukocyte migration to the peritoneum. The sulfated polysaccharides were extracted from the brown seaweed by proteolytic digestion, followed by sequential acetone precipitation producing 5 fractions. Gel lectrophoresis using 0.05 M 1,3-diaminopropane-acetate buffer, pH 9.0, stained with 0.1% toluidine blue, showed the presence of sulfated polysaccharides in all fractions. The chemical analyses demonstrated that all fractions are composed mainly of fucose, xylose, galactose, uronic acid, and sulfate. Electrophoresis in agarose gel in three different buffers demonstrated that the fraction 2.0v have only one population of fucan. This compound was purify by exclusion molecular. It has shown composition of fucose, xilose, sulfate and uronic acid in molar ration of 1.0: 1.7: 1.1: 0.5 respectively. The effect of this heterofucan on the leukocyte migration was observed 6h after zymozan (mg/g) administration into the peritoneum. The heterofucan showed higher antimigratory activity, it decrease the migration of leukocyte in 83.77% to peritoneum. The results suggest that this fucan is a new antimigratory compound with potential pharmacological appications

Protein partitioning in poly(ethylene glycol)/sodium polyacrylate aqueous two-phase systems

The partition of hemoglobin, lysozyme and glucose-6-phospate dehydrogenase (G6PDH) in a novel inexpensive aqueous two-phase system (ATPS) composed by poly(ethylene glycol) (PEG) and sodium polyacrylate (NaPA) has been studied. The effect of NaCl and Na2SO4, pH and PEG molecular size on the partitioning has been studied. At high pH (above 9), hemoglobin partitions strongly to the PEG-phase. Although some precipitation of hemoglobin occurs, high recovery values are obtained particularly for lysozyme and G6PDH. The partitioning forces are dominated by the hydrophobic and electrochemical (salt) effects, since the positively charged lysozyme and negatively charged G6PDH partitions to the non-charged PEG and the strongly negatively charged polyacrylate enriched phase, respectively. (c) 2007 Elsevier B.V. All rights reserved.