High data rate modulation of high power 1060-nm DBR tapered lasers with separate contacts

Direct optical modulation at 2.5 Gb/s with amplitude of more than 0.5 W has been demonstrated in single longitudinal mode distributed Bragg reflector tapered lasers emitting at 1060 nm with separated injection of the ridge waveguide and tapered sections. The modulating signal of ~110 mA peak to peak was applied to the ridge waveguide section, yielding a high modulation efficiency of ~5 W/A. The large-signal frequency response of the experimental set-up was limited by the bandwidth of the electrical amplifier rather than by the internal dynamics of the laser, indicating that higher bit rates could be achieved with improved driving electronics.

Design of a Two-Phase buck converter with fourth-order output filter for envelope amplifiers of limited bandwidth

The use of techniques such as envelope tracking (ET) and envelope elimination and restoration (EER) can improve the efficiency of radio frequency power amplifiers (RFPA). In both cases, high-bandwidth DC/DC converters called envelope amplifiers (EA) are used to modulate the supply voltage of the RFPA. This paper addresses the analysis and design of a modified two-phase Buck converter optimized to operate as EA. The effects of multiphase operation on the tracking capabilities are analyzed. The use of a fourth-order output filter is proposed to increase the attenuation of the harmonics generated by the PWM operation, thus allowing a reduction of the ratio between the switching frequency and the converter bandwidth. The design of the output filter is addressed considering envelope tracking accuracy and distortion caused by the side bands arising from the nonlinear modulation process. Finally, the proposed analysis and design methods are supported by simulation results, as well as demonstrated by experiments obtained using two 100-W, 10-MHz, two-phase Buck EAs capable of accurately tracking a 1.5-MHz bandwidth OFDM signal.

Design of a flat-top fiber Bragg filter via quasi-random modulation of the refractive index

The statistics of the reflection spectrum of a short-correlated disordered fiber Bragg grating are studied. The averaged spectrum appears to be flat inside the bandgap and has significantly suppressed sidelobes compared to the uniform grating of the same bandwidth. This is due to the Anderson localization of the modes of a disordered grating. This observation prompts a new algorithm for designing passband reflection gratings. Using the stochastic invariant imbedding approach it is possible to obtain the probability distribution function for the random reflection coefficient inside the bandgap and obtain both the variance of the averaged reflectivity as well as the distribution of the time delay of the grating.

Orientation masking and cross-orientation suppression (XOS):implications for estimates of channel bandwidth

Most contemporary models of spatial vision include a cross-oriented route to suppression (masking from a broadly tuned inhibitory pool), which is most potent at low spatial and high temporal frequencies (T. S. Meese & D. J. Holmes, 2007). The influence of this pathway can elevate orientation-masking functions without exciting the target mechanism, and because early psychophysical estimates of filter bandwidth did not accommodate this, it is likely that they have been overestimated for this corner of stimulus space. Here we show that a transient 40% contrast mask causes substantial binocular threshold elevation for a transient vertical target, and this declines from a mask orientation of 0° to about 40° (indicating tuning), and then more gently to 90°, where it remains at a factor of ∼4. We also confirm that cross-orientation masking is diminished or abolished at high spatial frequencies and for sustained temporal modulation. We fitted a simple model of pedestal masking and cross-orientation suppression (XOS) to our data and those of G. C. Phillips and H. R. Wilson (1984) and found the dependency of orientation bandwidth on spatial frequency to be much less than previously supposed. An extension of our linear spatial pooling model of contrast gain control and dilution masking (T. S. Meese & R. J. Summers, 2007) is also shown to be consistent with our results using filter bandwidths of ±20°. Both models include tightly and broadly tuned components of divisive suppression. More generally, because XOS and/or dilution masking can affect the shape of orientation-masking curves, we caution that variations in bandwidth estimates might reflect variations in processes that have nothing to do with filter bandwidth.

Acousto-optic modulation in a microstructured plastic optical fibre Bragg grating

The present work addresses the control of the mPOF Bragg grating spectrum properties through acousto-optic modulation. For the first time, the interaction of a flexural acoustic wave, generated by longitudinal excitation of different frequencies, with the Bragg grating will be presented. Also it will be demonstrated the quasi linear relationship between PZT load and maximum reflected power/ 3dB bandwidth of the reflected spectrum.

Dual-pump Raman amplification with enhanced flatness using modulation instability

In this work, we utilize modulation instability to the broadening of the two CW-pumps of a wideband Raman amplifier. Applying nonlinear fiber process, we demonstrate a feasibility of a certain control over the broadening process, leading to clear improvements in the flatness of the amplifier gain over its operational bandwidth.

Acousto-optic modulation in a microstructured plastic optical fibre Bragg grating

The present work addresses the control of the mPOF Bragg grating spectrum properties through acousto-optic modulation. For the first time, the interaction of a flexural acoustic wave, generated by longitudinal excitation of different frequencies, with the Bragg grating will be presented. Also it will be demonstrated the quasi linear relationship between PZT load and maximum reflected power/ 3dB bandwidth of the reflected spectrum.

Quasi-Orthogonal Space-Time Block Coding Using Polynomial Phase Modulation

Recently, polynomial phase modulation (PPM) was shown to be a power- and bandwidth-efficient modulation format. These two characteristics are in high demand nowadays specially in mobile applications, where devices with size, weight, and power (SWaP) constraints are common. In this paper, we propose implementing a full-diversity quasiorthogonal space-time block code (QOSTBC) using polynomial phase signals as modulation format. QOSTBCs along with PPM are used in order to improve the power efficiency of communication systems with four transmit antennas. We obtain the optimal PPM constellations that ensure full diversity and maximize the QOSTBC's minimum coding gain distance. Simulation results show that by using QOSTBCs along with a properly selected PPM constellation, full diversity in flat fading channels and thus low BER at high signal-to-noise ratios (SNR) can be ensured. More importantly, it is also shown that QOSTBCs using PPM achieve a better error performance than those using conventional modulation formats.

Modulateurs intégrés sur silicium pour la transmission de signaux à modulation d'amplitude multi-niveau

Au cours des dernières années, la photonique intégrée sur silicium a progressé rapidement. Les modulateurs issus de cette technologie présentent des caractéristiques potentiellement intéressantes pour les systèmes de communication à courte portée. En effet, il est prévu que ces modulateurs pourront être opérés à des vitesses de transmission élevées, tout en limitant le coût de fabrication et la consommation de puissance. Parallèlement, la modulation d’amplitude multi-niveau (PAM) est prometteuse pour ce type de systèmes. Ainsi, ce travail porte sur le développement de modulateurs de silicium pour la transmission de signaux PAM. Dans le premier chapitre, les concepts théoriques nécessaires à la conception de modulateurs de silicium sont présentés. Les modulateurs Mach-Zehnder et les modulateurs à base de réseau de Bragg sont principalement abordés. De plus, les effets électro-optiques dans le silicium, la modulation PAM, les différents types d’électrodes intégrées et la compensation des distorsions par traitement du signal sont détaillés.Dans le deuxième chapitre, un modulateur Mach-Zehnder aux électrodes segmentées est présenté. La segmentation des électrodes permet la génération de signaux optiques PAM à partir de séquences binaires. Cette approche permet d’éliminer l’utilisation de convertisseur numérique-analogique en intégrant cette fonction dans le domaine optique, ce qui vise à réduire le coût du système de communication. Ce chapitre contient la description détaillée du modulateur, les résultats de caractérisation optique et de la caractérisation électrique, ainsi que les tests systèmes. De plus, les tests systèmes incluent l’utilisation de pré-compensation ou de post-compensation du signal sous la forme d’égalisation de la réponse en fréquence pour les formats de modulation PAM-4 et PAM-8 à différents taux binaires. Une vitesse de transmission de 30 Gb/s est démontrée dans les deux cas et ce malgré une limitation importante de la réponse en fréquence suite à l’ajout d’un assemblage des circuits radiofréquences (largeur de bande 3 dB de 8 GHz). Il s’agit de la première démonstration de modulation PAM-8 à l’aide d’un modulateur Mach-Zehnder aux électrodes segmentées. Finalement, les conclusions tirées de ce travail ont mené à la conception d’un deuxième modulateur Mach-Zehnder aux électrodes segmentées présentement en phase de test, dont les performances montrent un très grand potentiel. Dans le troisième chapitre, un modulateur à réseau de Bragg à deux sauts de phase est présenté. L’utilisation de réseaux de Bragg est une approche encore peu développée pour la modulation. En effet, la réponse spectrale de ces structures peut être contrôlée précisément, une caractéristique intéressante pour la conception de modulateurs. Dans ces travaux, nous proposons l’ajout de deux sauts de phase à un réseau de Bragg uniforme pour obtenir un pic de transmission dans la bande de réflexion de celui-ci. Ainsi, il est possible d’altérer l’amplitude du pic de transmission à l’aide d’une jonction pn. Comme pour le deuxième chapitre, ce chapitre inclut la description détaillée du modulateur, les résultats des caractérisations optique et électrique, ainsi que les tests systèmes. De plus, la caractérisation de jonctions pn à l’aide du modulateur à réseau de Bragg est expliquée. Des vitesses de transmission PAM-4 de 60 Gb/s et OOK de 55 Gb/s sont démontrées après la compensation des distorsions des signaux. À notre connaissance, il s’agit du modulateur à réseau de Bragg le plus rapide à ce jour. De plus, pour la première fois, les performances d’un tel modulateur s’approchent de celles des modulateurs de silicium les plus rapides utilisant des microrésonateurs en anneau ou des interféromètres Mach-Zehnder.

Acousto-optic modulation of optical reflection properties in fiber Bragg gratings and the application in fiber lasers

This thesis aims to investigate the interaction of acoustic waves and fiber Bragg gratings (FBGs) in standard and suspended-core fibers (SCFs), to evaluate the influence of the fiber, grating and modulator design on the increase of the modulation efficiency, bandwidth and frequency. Initially, the frequency response and the resonant acoustic modes of a low frequency acousto-optic modulator (f < 1.2 MHz) are numerically investigated by using the finite element method. Later, the interaction of longitudinal acoustic waves and FBGs in SCFs is also numerically investigated. The fiber geometric parameters are varied and the strain and grating properties are simulated by means of the finite element method and the transfer matrix method. The study indicates that the air holes composing the SCF cause a significant reduction of the amount of silica in the fiber cross section increasing acousto-optic interaction in the core. Experimental modulation of the reflectivity of FBGs inscribed in two distinct SCFs indicates evidences of this increased interaction. Besides, a method to acoustically induce a dynamic phase-shift in a chirped FBG employing an optimized design of modulator is shown. Afterwards, a combination of this modulator and a FBG inscribed in a three air holes SCF is applied to mode-lock an ytterbium doped fiber laser. To improve the modulator design for future applications, two other distinct devices are investigated to increase the acousto-optic interaction, bandwidth and frequency (f > 10 MHz). A high reflectivity modulation has been achieved for a modulator based on a tapered fiber. Moreover, an increased modulated bandwidth (320 pm) has been obtained for a modulator based on interaction of a radial long period grating (RLPG) and a FBG inscribed in a standard fiber. In summary, the results show a considerable reduction of the grating/fiber length and the modulator size, indicating possibilities for compact and faster acousto-optic fiber devices. Additionally, the increased interaction efficiency, modulated bandwidth and frequency can be useful to shorten the pulse width of future all-fiber mode-locked fiber lasers, as well, to other photonic devices which require the control of the light in optical fibers by electrically tunable acoustic waves.

Necessary skills and practices required for effective participation in high bandwidth design team activities

Technology is continually changing, and evolving, throughout the entire construction industry; and particularly in the design process. One of the principal manifestations of this is a move away from team working in a shared work space to team working in a virtual space, using increasingly sophisticated electronic media. Due to the significant operating differences when working in shared and virtual spaces adjustments to generic skills utilised by members is a necessity when moving between the two conditions. This paper reports an aspect of a CRC-CI research project based on research of ‘generic skills’ used by individuals and teams when engaging with high bandwidth information and communication technologies (ICT). It aligns with the project’s other two aspects of collaboration in virtual environments: ‘processes’ and ‘models’. The entire project focuses on the early stages of a project (i.e. design) in which models for the project are being developed and revised. The paper summarises the first stage of the research project which reviews literature to identify factors of virtual teaming which may affect team member skills. It concludes that design team participants require ‘appropriate skills’ to function efficiently and effectively, and that the introduction of high band-width technologies reinforces the need for skills mapping and measurement.

Studying collaborative design in high bandwidth virtual environments

In today’s global design world, architectural and other related design firms design across time zones and geographically distant locations. High bandwidth virtual environments have the potential to make a major impact on these global design teams. However, there is insufficient evidence about the way designers collaborate in their normal working environments using traditional and/or digital media. This paper presents a method to study the impact of communication and information technologies on collaborative design practice by comparing design tasks done in a normal working environment with design tasks done in a virtual environment. Before introducing high bandwidth collaboration technology to the work environment, a baseline study is conducted to observe and analyze the existing collaborative process. Designers currently rely on phone, fax, email, and image files for communication and collaboration. Describing the current context is important for comparison with the following phases. We developed the coding scheme that will be used in analyzing three stages of the collaborative design activity. The results will establish the basis for measures of collaborative design activity when a new technology is introduced later to the same work environment – for example, designers using electronic whiteboards, 3D virtual worlds, webcams, and internet phone. The results of this work will form the basis of guidelines for the introduction of technology into global design offices