Measurement of in-service insulated rail joint tie plate response

This paper presents the results of a recent investigation into Insulated Rail Joint Tie Plate fatigue failures. In particular it focuses on the results of data obtained through field strain gauge and accelerometer measurements of in-service Insulated Rail Joint Tie Plates. These measurements have identified a significant variability in the strains present in similar joints operating under identical load conditions. This variability in stress invariably has a significant influence on the life of the joints. The results of rainflow counting and a fatigue analysis are also presented.

Exeter short stems compared with standard length Exeter stems : experience from the Australian Orthopaedic Association National Joint Replacement Registry

The standard Exeter stem has a length of 150mm with offsets 37.5mm to 56mm. Shorter stems of lengths 95mm, 115mm and 125mm with offsets 35.5mm or less are available for patients with smaller femurs. Concern has been raised regarding the behaviour of the smaller implants. This paper analysed data from the Australian Orthopaedic Association National Joint Replacement Registry comparing survivorship of stems of offset 35.5mm or less with the standard stems of 37.5mm offset or greater. At seven years there was no significant difference in the Cumulative Percent Revision Rate in the short stems (3.4%, 95% CI 2.4-4.8%) compared with the standard length stems (3.5%, 95% CI 3.3-3.8%) despite its use in a greater proportion of potentially more difficult developmental dysplasia of the hip cases.

Field measurement of wheel-rail impact force at insulated rail joint

When wheels pass over insulated rail joints (IRJs) a vertical impact force is generated. The ability to measure the impact force is valuable as the force signature helps understand the behaviour of the IRJs, in particular their potential for failure. The impact forces are thought to be one of the main factors that cause damage to the IRJ and track components. Study of the deterioration mechanism helps finding new methods to improve the service life of IRJs in track. In this research, the strain-gage-based wheel load detector, for the first time, is employed to measure the wheel–rail contact-impact force at an IRJ in a heavy haul rail line. In this technique, the strain gages are installed within the IRJ assembly without disturbing the structural integrity of IRJ and arranged in a full wheatstone bridge to form a wheel load detector. The instrumented IRJ is first tested and calibrated in the lab and then installed in the field. For comparison purposes, a reference rail section is also instrumented with the same strain gage pattern as the IRJ. In this paper the measurement technique, the process of instrumentation, and tests as well as some typical data obtained from the field and the inferences are presented.

Submission to the Joint Select Committee on Cyber Safety. Inquiry into the Cybersafety of Seniors.

This submission addresses the following terms of reference: 1) the nature, prevalence and level of cybersafety risks and threats experienced by senior Australians; 2) the impact and implications of those risks and threats on access and use of information and communication technologies by senior Australians; 3) the adequacy and effectiveness of current government and industry initiatives to respond to those threats, including education initiatives aimed at senior Australians; 4) best practice safeguards, and any possible changes to Australian law, policy or practice that will strengthen the cybersafety of senior Australians.

Joint Ventures Law in Australia (3rd ed.)

Following on from the 2nd edition published in 2005, this new edition updates its predecessor and adds considerable new material as a result of changes in the law generally and commercial approaches to financing joint ventures in particular. Of special note, Financing of Joint Ventures has been completely re-written with considerable additions to take account of the new legislative regimes such as the Personal Property Securities. The impact of climate change legislation has been covered, specifically carbon pricing with additional material on structuring generally and particularly in relation to large joint ventures with governments through Public Private Partnerships. A new Chapter has been added called Resources Joint Ventures and undertakes a thorough analysis of a typical resources joint venture and is heavily cross referenced into the chapter on Default which has also been updated. In addition, International Joint Ventures now includes additional material on structuring and dispute resolution and Joint Ventures and the Competition and Consumer Act has been substantially re-written to take account of 2009 legislative amendments on cartel conduct, and the impact of changes wrought by the Competition and Consumer Act 2010. All other chapters and material has been updated to accommodate other legislative changes and new case law over the seven years since the last edition.

Common law obligations of good faith in non-fiduciary joint ventures

This chapter is devoted to the issue of non-fiduciary common law obligations of good faith, as they may arise in the performance and enforcement of joint ventures. In recent times a rush of commercial contractual claims involving good faith has signified the need for a separate chapter examining this issue. Although most of these decisions have arisen in commercial contexts other than joint ventures, the decisions, nevertheless, warrant careful consideration to the extent that they cast light on the likely contours of the common law good faith obligation as it may apply in the joint venture context.

Joint ventures and the Competition and Consumer Act

The purpose of this chapter is to analyse the way in which joint venture agreements can fall within the competition provisions of the Competition and Consumer Act 2010, and the circumstances in which authorisation may be available for joint venture collaborations.

Intellectual Property and Joint Ventures

Following upon the success of the 2nd edition published in 2005, this new edition not only updates its predecessor but also adds considerable new material in consequences of changes in the law generally and commercial approaches to financing joint ventures in particular. Of special note are the following: Financing of Joint Ventures has been completely re-written with considerable additions to take account of the new legislative regimes such as the Personal Property Securities, the impact of climate change legislation, specifically carbon pricing with additional material on structuring generally and particularly in relation to large joint ventures with governments through Public Private Partnerships. A new Chapter called Resources Joint Ventures undertakes a thorough analysis of a typical resources joint venture and is heavily cross referenced into the chapter on Default which has also been updated. International Joint Ventures now includes additional material on structuring and dispute resolution. Joint Ventures and the Competition and Consumer Act has been substantially re-written to take account of 2009 legislative amendments on cartel conduct, and the impact of changes wrought by the Competition and Consumer Act 2010. All other chapters and material has been updated to accommodate other legislative changes and new case law over the seven years since the last edition.

Lifting the joint venture veil : liability of related entities for misleading conduct of agents engaged by joint venture partners

At common law, a corporation may be liable vicariously for the conduct of its appointed agents, employees or directors. This generally requires the agent or employee to be acting in the course of his or her agency or employment and, in the case of representations, to have actual or implied authority to make the representations. The circumstances in which a corporation may be liable for the conduct of its agents, employees or directors is broadened under the Australian Consumer Law (ACL) to where one of these parties engages in conduct “on behalf of” the corporation. As the decision in Bennett v Elysium Noosa Pty Ltd (in liq) demonstrates, this may extend to liability for the misleading conduct of a salesperson for the joint venture to parties who are not formal members of the joint venture, but where the joint venture activities are within the course of the entity’s “business, affairs or activities”.

Locally weighted learning model predictivek control for elastic joint robots

This paper proposes an efficient and online learning control system that uses the successful Model Predictive Control (MPC) method in a model based locally weighted learning framework. The new approach named Locally Weighted Learning Model Predictive Control (LWL-MPC) has been proposed as a solution to learn to control complex and nonlinear Elastic Joint Robots (EJR). Elastic Joint Robots are generally difficult to learn to control due to their elastic properties preventing standard model learning techniques from being used, such as learning computed torque control. This paper demonstrates the capability of LWL-MPC to perform online and incremental learning while controlling the joint positions of a real three Degree of Freedom (DoF) EJR. An experiment on a real EJR is presented and LWL-MPC is shown to successfully learn to control the system to follow two different figure of eight trajectories.

Intellectual property and joint ventures

This chapter outlines the most important ways in which intellectual property is protected in Australia, and also the factors which affect the rights of joint venture participants in the absence of specific agreement between such participants. It then examines particular issues which may be considered in preparing appropriate documentation for any joint venture which involves the utilisation or generation of intellectual property to ensure that the joint venture participants achieve their desired result in terms of the allocation of ownership and control of such rights. The analysis includes and explanation of the special considerations which affect co-operation in research between industry and a university or government research institution. Finally, the rights of the joint venturers to intellectual property upon termination of the joint ventures are considered.

UCPR r 360 – offers to settle – joint offer by first and second plaintiffs

The decision in ACN 070 037 599 Pty Ltd v Larvik Pty Ltd (No 2) [2008] QSC 118 involved a consideration of the implications for a plaintiff whose offer to settle under Part 5 of the Uniform Civil Procedure Rules 1999 (Qld) was made jointly with another plaintiff who abandoned her action before trial. The court found nothing wrong with the making of a joint offer. It concluded the successful plaintiff would be entitled to indemnity costs on the simple test of whether the judgment for that plaintiff was more favourable than the offer.

Segmental torso masses and coronal plane joint torques in the adolescent scoliotic spine

Introduction. Calculating segmental (vertebral level-by-level) torso masses in Adolescent Idiopathic Scoliosis (AIS) patients allows the gravitational loading on the scoliotic spine during relaxed standing to be determined. This study used CT scans of AIS patients to measure segmental torso masses and explores how joint moments in the coronal plane are affected by changes in the position of the intervertebral joint’s axis of rotation; particularly at the apex of a scoliotic major curve. Methods. Existing low dose CT data from the Paediatric Spine Research Group was used to calculate vertebral level-by-level torso masses and joint torques occurring in the spine for a group of 20 female AIS patients (mean age 15.0 ± 2.7 years, mean Cobb angle 53 ± 7.1°). Image processing software, ImageJ (v1.45 NIH USA) was used to threshold the T1 to L5 CT images and calculate the segmental torso volume and mass corresponding to each vertebral level. Body segment masses for the head, neck and arms were taken from published anthropometric data. Intervertebral (IV) joint torques at each vertebral level were found using principles of static equilibrium together with the segmental body mass data. Summing the torque contributions for each level above the required joint, allowed the cumulative joint torque at a particular level to be found. Since there is some uncertainty in the position of the coronal plane Instantaneous Axis of Rotation (IAR) for scoliosis patients, it was assumed the IAR was located in the centre of the IV disc. A sensitivity analysis was performed to see what effect the IAR had on the joint torques by moving it laterally 10mm in both directions. Results. The magnitude of the torso masses from T1-L5 increased inferiorly, with a 150% increase in mean segmental torso mass from 0.6kg at T1 to 1.5kg at L5. The magnitudes of the calculated coronal plane joint torques during relaxed standing were typically 5-7 Nm at the apex of the curve, with the highest apex joint torque of 7Nm being found in patient 13. Shifting the assumed IAR by 10mm towards the convexity of the spine, increased the joint torque at that level by a mean 9.0%, showing that calculated joint torques were moderately sensitive to the assumed IAR location. When the IAR midline position was moved 10mm away from the convexity of the spine, the joint torque reduced by a mean 8.9%. Conclusion. Coronal plane joint torques as high as 7Nm can occur during relaxed standing in scoliosis patients, which may help to explain the mechanics of AIS progression. This study provides new anthropometric reference data on vertebral level-by-level torso mass in AIS patients which will be useful for biomechanical models of scoliosis progression and treatment. However, the CT scans were performed in supine (no gravitational load on spine) and curve magnitudes are known to be smaller than those measured in standing.

Segmental torso masses and gravity-induced coronal plane joint moments in adolescent idiopathic scoliosis

Introduction: Calculating segmental (vertebral level-by-level) torso masses in Adolescent Idiopathic Scoliosis (AIS) patients allows the gravitational loading on the scoliotic spine during relaxed standing to be estimated. This study used supine CT scans of AIS patients to measure segmental torso masses and explored the joint moments in the coronal plane, particularly at the apex of a scoliotic major curve. Methods: Existing low dose CT data from the Paediatric Spine Research Group was used to calculate vertebral level-by-level torso masses and joint moments occurring in the spine for a group of 20 female AIS patients with right sided thoracic curves. The mean age was 15.0 ± 2.7 years and all curves were classified Lenke Type 1 with a mean Cobb angle 52 ± 5.9°. Image processing software, ImageJ (v1.45 NIH USA) was used to create reformatted coronal plane images, reconstruct vertebral level-by-level torso segments and subsequently measure the torso volume corresponding to each vertebral level. Segment mass was then determined by assuming a tissue density of 1.04x103 kg/m3. Body segment masses for the head, neck and arms were taken from published anthropometric data (Winter 2009). Intervertebral joint moments in the coronal plane at each vertebral level were found from the position of the centroid of the segment masses relative to the joint centres with the segmental body mass data. Results and Discussion: The magnitude of the torso masses from T1-L5 increased inferiorly, with a 150% increase in mean segmental torso mass from 0.6kg at T1 to 1.5kg at L5. The magnitudes of the calculated coronal plane joint moments during relaxed standing were typically 5-7 Nm at the apex of the curve, with the highest apex joint torque of 7Nm. The CT scans were performed in the supine position and curve magnitudes are known to be 7-10° smaller than those measured in standing, due to the absence of gravity acting on the spine. Hence, it can be expected that the moments produced by gravity in the standing individual will be greater than those calculated here.