Biomechanical force displacement analysis of strength of fixation of tracker holding devices to bone in computer aided joint replacement

Computer aided joint replacement surgery has become very popular during recent years and is being done in increasing numbers all over the world. The accuracy of the system depends to a major extent, on accurate registration and immobility of the tracker attachment devices to the bone. This study was designed to asses the forces needed to displace the tracker attachment devices in the bone simulators. Bone simulators were used to maintain the uniformity of the bone structure during the study. The fixation devices tested were 3mm diameter self drilling, self tapping threaded pin, 4mm diameter self tapping cortical threaded pin, 5mm diameter self tapping cancellous threaded pin and a triplanar fixation device ‘ortholock’ used with three 3mm pins. All the devices were tested for pull out, translational and rotational forces in unicortical and bicortical fixation modes. Also tested was the normal bang strength and forces generated by leaning on the devices. The forces required to produce translation increased with the increasing diameter of the pins. These were 105N, 185N, and 225N for the unicortical fixations and 130N, 200N, 225N for the bicortical fixations for 3mm, 4mm and 5mm diameter pins respectively. The forces required to pull out the pins were 1475N, 1650N, 2050N for the unicortical, 1020N, 3044N and 3042N for the bicortical fixated 3mm, 4mm and 5mm diameter pins. The ortholock translational and pull out strength was tested to 900N and 920N respectively and still it did not fail. Rotatory forces required to displace the tracker on pins was to the magnitude of 30N before failure. The ortholock device had rotational forces applied up to 135N and still did not fail. The manual leaning forces and the sudden bang forces generated were of the magnitude of 210N and 150N respectively. The strength of the fixation pins increases with increasing diameter from three to five mm for the translational forces. There is no significant difference in pull out forces of four mm and five mm diameter pins though it is more that the three mm diameter pins. This is because of the failure of material at that stage rather than the fixation device. The rotatory forces required to displace the tracker are very small and much less that that can be produced by the surgeon or assistants in single pins. Although the ortholock device was tested to 135N in rotation without failing, one has to be very careful not to put any forces during the operation on the tracker devices to ensure the accuracy of the procedure.

Tackling the burden of injury in Australasia : developing a binational trauma registry

Existing trauma registries in Australia and New Zealand play an important role in monitoring the management of injured patients. Over the past decade, such monitoring has been translated into changes in clinical processes and practices. Monitoring and changes have been ad hoc, as there are currently no Australasian benchmarks for “optimal” injury management. A binational trauma registry is urgently needed to benchmark injury management to improve outcomes for injured patients.

Joint venture behaviour in construction industry : an Australia case study

Joint ventures can take many forms and can be formed for different reasons, from sharing resources to creating future business opportunities. At the same time, there is increasing interest and discussion of alternative procurement methods, moving away from traditional procurement systems to relational approaches. Business systems and strategies need to be redefined and move from a short-term project to project culture to a more strategic, long-term perspective. Joint ventures of construction organisations, global and local, have become increasingly popular to deliver large-scale infrastructure construction projects. However, successful strategic collaborations require project organisations to formulate a fit between contractual and operational arrangements for each situation. This study reviews the movement from traditional procurement methods towards relational contracting approaches in Queensland, Australia. The study examines the organisational factors that facilitates sustainable relationship between project organisations and hence, lead to long-term business success. This paper reports on initial findings captured from a survey undertaken with construction contracting organisations in Australia, focusing on the supply chain relationships. Contractors’ perceptions of the relationship management process and the engagement of the supply chain are also presented.

Cognitive assessment in closed head injury : stability, validity and parallel forms for two neuropsychological measures of recovery

Investigated the psychometric properties of the original and alternate sets of the Trail Making Test (TMT) and the Controlled Oral Word Association Test (COWAT; A. L. Benton and D. Hamsher, 1978) in 50 orthopedic and 15 closed head injured (1 yr after trauma) patients (aged 15–59 yrs). Although the alternate forms of both measures proved to be stable and consistent with each other in both groups, only the parallel sets of TMT reliably discriminated the clinical group from controls. Practice effects in the head injured were significant only for Trail B of TMT. Factor analysis of the control group's results identified Verbal Knowledge as a major contributor to performance on COWAT, whereas TMT was more dependent on Rapid Visual Search and Visuomotor Sequencing.

The use of narrative text for injury surveillance research : a systematic review

Objective: To summarise the extent to which narrative text fields in administrative health data are used to gather information about the event resulting in presentation to a health care provider for treatment of an injury, and to highlight best practise approaches to conducting narrative text interrogation for injury surveillance purposes.----- Design: Systematic review----- Data sources: Electronic databases searched included CINAHL, Google Scholar, Medline, Proquest, PubMed and PubMed Central.. Snowballing strategies were employed by searching the bibliographies of retrieved references to identify relevant associated articles.----- Selection criteria: Papers were selected if the study used a health-related database and if the study objectives were to a) use text field to identify injury cases or use text fields to extract additional information on injury circumstances not available from coded data or b) use text fields to assess accuracy of coded data fields for injury-related cases or c) describe methods/approaches for extracting injury information from text fields.----- Methods: The papers identified through the search were independently screened by two authors for inclusion, resulting in 41 papers selected for review. Due to heterogeneity between studies metaanalysis was not performed.----- Results: The majority of papers reviewed focused on describing injury epidemiology trends using coded data and text fields to supplement coded data (28 papers), with these studies demonstrating the value of text data for providing more specific information beyond what had been coded to enable case selection or provide circumstantial information. Caveats were expressed in terms of the consistency and completeness of recording of text information resulting in underestimates when using these data. Four coding validation papers were reviewed with these studies showing the utility of text data for validating and checking the accuracy of coded data. Seven studies (9 papers) described methods for interrogating injury text fields for systematic extraction of information, with a combination of manual and semi-automated methods used to refine and develop algorithms for extraction and classification of coded data from text. Quality assurance approaches to assessing the robustness of the methods for extracting text data was only discussed in 8 of the epidemiology papers, and 1 of the coding validation papers. All of the text interrogation methodology papers described systematic approaches to ensuring the quality of the approach.----- Conclusions: Manual review and coding approaches, text search methods, and statistical tools have been utilised to extract data from narrative text and translate it into useable, detailed injury event information. These techniques can and have been applied to administrative datasets to identify specific injury types and add value to previously coded injury datasets. Only a few studies thoroughly described the methods which were used for text mining and less than half of the studies which were reviewed used/described quality assurance methods for ensuring the robustness of the approach. New techniques utilising semi-automated computerised approaches and Bayesian/clustering statistical methods offer the potential to further develop and standardise the analysis of narrative text for injury surveillance.

Injury bulletin 105 : skateboard injury

Summary of findings: QISU estimates that approximately 1,000 skateboard-associated injuries are seen at emergency departments each year in Queensland. 10-14 year old males are the most likely group to present to a QISU ED with a skateboard related injury. The peak time for skateboard injuries to occur is on the weekend and in the late afternoon. Only 19% of skateboard injuries occur at skate park facilities, with the remainder oc-curring in non-skate parks, on roads and footpaths. Risk factors associated with more severe injuries are, age less than 10 years and involvement in a motor vehicle crash The most common types of injuries are fractures and sprains of the upper limbs. Isolated head injuries represent approximately 5% of skateboarding injuries, but 60% of serious injuries requiring resuscitation. These injuries may be minimized or pre-vented with helmet use.

Pram and stroller related injury in Queensland children under 5 years of age

An estimated 200 Queensland children under 5 years of age are injured every year in incidents involving prams or strollers. The majority of injuries are due to falls from or falls with the pram or stroller Nineteen children were identified as having been caught in the pram or stroller mechanism (13 sustained finger injuries). Stairs and escalators were a factor in nearly 10 percent of pram or stroller fall injuries, with children being tipped out of the pram or stroller, or rolling down the stairs in the device. Roll away injuries accounted for eight percent of all pram or stroller fall injuries (some also involving stairs) Roll away injuries could be prevented by a default brake system similar to airport trolleys. Pram or stroller failure was identified in 2% of injuries

Curriculum development of joint degrees courses with international institutions

With globalisation and severe budget constraints in the education sector in Australia and around the world it has become necessary for higher education institutions to be more outward looking and seek funding from non traditional sources to supplement the financial shortfalls. One way to overcome this problem is to work cooperatively with other institutions to share facilities and courses, at the same time generating valuable income to maintain the operation of the university. This paper describes the development of joint curricula in built environment and engineering courses in QUT. It outlines the stages of development starting from seeking international partners, developing memorandum of understanding, making visit to partner institution to inspect the facilities, curriculum development to meet the academic requirements of the institutions and professional bodies and finally the implementation process.

Design of automatic vision-based inspection system for solder joint segmentation

Purpose: Computer vision has been widely used in the inspection of electronic components. This paper proposes a computer vision system for the automatic detection, localisation, and segmentation of solder joints on Printed Circuit Boards (PCBs) under different illumination conditions. Design/methodology/approach: An illumination normalization approach is applied to an image, which can effectively and efficiently eliminate the effect of uneven illumination while keeping the properties of the processed image the same as in the corresponding image under normal lighting conditions. Consequently special lighting and instrumental setup can be reduced in order to detect solder joints. These normalised images are insensitive to illumination variations and are used for the subsequent solder joint detection stages. In the segmentation approach, the PCB image is transformed from an RGB color space to a YIQ color space for the effective detection of solder joints from the background. Findings: The segmentation results show that the proposed approach improves the performance significantly for images under varying illumination conditions. Research limitations/implications: This paper proposes a front-end system for the automatic detection, localisation, and segmentation of solder joint defects. Further research is required to complete the full system including the classification of solder joint defects. Practical implications: The methodology presented in this paper can be an effective method to reduce cost and improve quality in production of PCBs in the manufacturing industry. Originality/value: This research proposes the automatic location, identification and segmentation of solder joints under different illumination conditions.

Automatic solder joint defect classification using the Log-Gabor filter

This paper proposes the validity of a Gabor filter bank for feature extraction of solder joint images on Printed Circuit Boards (PCBs). A distance measure based on the Mahalanobis Cosine metric is also presented for classification of five different types of solder joints. From the experimental results, this methodology achieved high accuracy and a well generalised performance. This can be an effective method to reduce cost and improve quality in the production of PCBs in the manufacturing industry.

Mathematical modelling of muscle recruitment and function in the lumbar spine

Low back pain is an increasing problem in industrialised countries and although it is a major socio-economic problem in terms of medical costs and lost productivity, relatively little is known about the processes underlying the development of the condition. This is in part due to the complex interactions between bone, muscle, nerves and other soft tissues of the spine, and the fact that direct observation and/or measurement of the human spine is not possible using non-invasive techniques. Biomechanical models have been used extensively to estimate the forces and moments experienced by the spine. These models provide a means of estimating the internal parameters which can not be measured directly. However, application of most of the models currently available is restricted to tasks resembling those for which the model was designed due to the simplified representation of the anatomy. The aim of this research was to develop a biomechanical model to investigate the changes in forces and moments which are induced by muscle injury. In order to accurately simulate muscle injuries a detailed quasi-static three dimensional model representing the anatomy of the lumbar spine was developed. This model includes the nine major force generating muscles of the region (erector spinae, comprising the longissimus thoracis and iliocostalis lumborum; multifidus; quadratus lumborum; latissimus dorsi; transverse abdominis; internal oblique and external oblique), as well as the thoracolumbar fascia through which the transverse abdominis and parts of the internal oblique and latissimus dorsi muscles attach to the spine. The muscles included in the model have been represented using 170 muscle fascicles each having their own force generating characteristics and lines of action. Particular attention has been paid to ensuring the muscle lines of action are anatomically realistic, particularly for muscles which have broad attachments (e.g. internal and external obliques), muscles which attach to the spine via the thoracolumbar fascia (e.g. transverse abdominis), and muscles whose paths are altered by bony constraints such as the rib cage (e.g. iliocostalis lumborum pars thoracis and parts of the longissimus thoracis pars thoracis). In this endeavour, a separate sub-model which accounts for the shape of the torso by modelling it as a series of ellipses has been developed to model the lines of action of the oblique muscles. Likewise, a separate sub-model of the thoracolumbar fascia has also been developed which accounts for the middle and posterior layers of the fascia, and ensures that the line of action of the posterior layer is related to the size and shape of the erector spinae muscle. Published muscle activation data are used to enable the model to predict the maximum forces and moments that may be generated by the muscles. These predictions are validated against published experimental studies reporting maximum isometric moments for a variety of exertions. The model performs well for fiexion, extension and lateral bend exertions, but underpredicts the axial twist moments that may be developed. This discrepancy is most likely the result of differences between the experimental methodology and the modelled task. The application of the model is illustrated using examples of muscle injuries created by surgical procedures. The three examples used represent a posterior surgical approach to the spine, an anterior approach to the spine and uni-lateral total hip replacement surgery. Although the three examples simulate different muscle injuries, all demonstrate the production of significant asymmetrical moments and/or reduced joint compression following surgical intervention. This result has implications for patient rehabilitation and the potential for further injury to the spine. The development and application of the model has highlighted a number of areas where current knowledge is deficient. These include muscle activation levels for tasks in postures other than upright standing, changes in spinal kinematics following surgical procedures such as spinal fusion or fixation, and a general lack of understanding of how the body adjusts to muscle injuries with respect to muscle activation patterns and levels, rate of recovery from temporary injuries and compensatory actions by other muscles. Thus the comprehensive and innovative anatomical model which has been developed not only provides a tool to predict the forces and moments experienced by the intervertebral joints of the spine, but also highlights areas where further clinical research is required.

An adolescent injury intervention : selecting targeted behaviours with implications for program design and evaluation

Objectives: This paper sought to identify the behaviour change targets for an injury prevention program; Skills for Preventing Injury in Youth, SPIY. The aim was to explore how such behaviours could subsequently be implemented and evaluated in the program. Methods and Design: The quantitative procedure involved a survey with 267 Year 8 and 9 students (mean age 13.23 years) regarding their engagement in risk-taking behaviours that may lead to injury. The qualitative study involved 30 students aged 14 to 17 years reporting their experiences of injury and risk-taking. Results: Injury risk behaviours co-occurred among three-quarters of those who reported engaging in any alcohol use or transport or violence related injury risk behaviour. Students described in detail some of these experiences. Conclusions: The selection process of identifying target behaviours for change for an injury prevention program is described. Adolescents’ description of such risk behaviours can inform the process of operationalising and contextualising program content and deciding on evaluation methodology. The design of an effective injury prevention program involves considerable preparatory work and this paper was able to describe the process of identifying the behavioural targets for change that can be operationalised and evaluated in the injury prevention program, SPIY.

A short-term evaluation of a school-based early adolescent injury prevention program

This paper reports on the development of a school-based intervention to reduce risk-taking and associated injuries. There is limited but important evidence that intervention design should ensure participation does not lead to an increase in target risk behaviors with some studies in alcohol and drug prevention finding unexpected negative effects. The short-term evaluation of Skills for Preventing Injury in Youth (SPIY) examined change in interpersonal violence, alcohol and transport-related risks. Intervention (n = 360) and comparison (n = 180) students were surveyed pre/post-intervention. A qualitative analysis based on focus groups (70 students) explored experiences of change. Findings indicate significant positive changes reinforced by students’ reports. A decrease in reported risk-taking for the intervention group and an increase in the comparison group were observed. These findings endorse SPIY as a useful curriculum approach to reducing injuries and lend support to the future conduct of a long-term outcome evaluation.