The effects of humidity on tin whisker growth by immersion tin plating and tin solder dipping surface finishes

The drive to replace lead (Pb) from electronics has led to the replacement of tin (Sn) alloys as the terminal plating for electronic devices. However, the deposition of Sn based alloys as the component surface finish tends to induce Sn whisker that causes unintended electric shorts when the conductive whiskers grow across to the adjacent conductor. Internal stress is considered as the driving force that causes the growth of Sn whiskers. In this study, stress type of elevated temperature/ humidity exposure at 55C/85%RH with the storage for up to 24 months was conducted to define the acceleration factor in samples with deposition of immersion Sn plating and Sn solder dipping. The addition of Nickel (Ni) under-layer was also applied to examine the correlation to field conditions. The results showed that the whisker length increased in high humidity irrespective of the deposition methods. It was also shown that pure Sn solder dipping mitigated the whisker growth but does not completely prevent it when alloying Sn with 0.4%wtCu. Additionally, Ni under-layer was indicated to be more efficient in mitigating the growth of whisker by prolonging the incubation time for whisker formation.

The emerging role of microRNAs in resistance to lung cancer treatments

One of the major challenges in the treatment of lung cancer is the development of drug resistance. This represents a major obstacle in the treatment of patients, limiting the efficacy of both conventional chemotherapy and biological therapies. Deciphering the mechanisms of resistance is critical to further understanding the multifactorial pathways involved, and in developing more specific targeted treatments. To date, numerous studies have reported the potential role of microRNAs (miRNAs) in resistance to various cancer treatments. MicroRNAs are a family of small non-coding RNAs that regulate gene expression by sequence-specific targeting of mRNAs causing translational repression or mRNA degradation. More than 1200 validated human miRNAs have been identified to date. While as little as one miRNA can regulate hundreds of targets, a single target can also be affected by multiple miRNAs. Evidence suggests that dysregulation of specific miRNAs may be involved in the acquisition of resistance to a number of cancer treatments, thereby modulating the sensitivity of cancer cells to such therapies. Therefore, targeting miRNAs may be an attractive strategy for developing novel and more effective individualized therapies, improving drug efficiency, and for predicting patient response to different treatments. In this review, we provide an overview on the role of miRNAs in resistance to current lung cancer therapies and novel biological agents.

Effects of surface treatments and size of fly ash particles on the compressive properties of epoxy based particulate composites

Particulate reinforcements for polymers are selected with dual objective of improving composite properties and save on the total cost of the system. In the present study fly ash, an industrial waste with good properties is used as filler in epoxy and the compressive properties of such composites are studied. Particle surfaces are treated chemically using a silane-coupling agent to improve the compatibility with the matrix. The compressive properties of these are compared with those made of untreated fly ash particulates. Furthermore properties of fly ash composites with two different average particle sizes are first compared between themselves and then with those made using the as-received bimodal nature of particle size distribution. Microscopic observations of compression tested samples revealed a better adherence of the particles with the matrix in case of treated particles and regards the size effect the composites with lower average particle size showed improved strength at higher filler contents. Experimental values of strengths and modulii are compared with some of the theoretical models for composite properties. (C) 2002 Kluwer Academic Publishers.

Coatings and surface treatments for protection against low-velocity erosion-corrosion in fluidized beds

Surface coatings and treatments have been used to reduce material loss of components in bubbling fluidized bed combustors (FBCs). The performance of protective coatings in FBC boilers and laboratory simulations is reviewed. Important coating properties to minimize wastage appear to be high hardness, low oxidation rate, low porosity, high adhesion and sufficient thickness to maintain protection for a long period. Economic considerations and criteria for choosing a suitable coating or treatment are discussed for the different types of bubbling FBC. © 1995.

One-dimensional improvement and two-dimensional and 3-dimensional treatments for stable oscillation condition, mode structure and power output in high-speed-flow lasers

For high-speed-flow lasers, the one-dimensional and first-order approximate treatment in[1] under approximation of geometrical optics is improved still within the scope of approx-imation of geometrical optics. The strict accurate results are obtained, and what is more,two- and three-dimensional treatments are done. Thus for two- and three-dimensional cases, thestable oscillation condition, the formulae of power output and analytical expression of modesunder approximation of geometrical optics (in terms of gain function) are derived. Accord-ing to the present theory, one-and two-dimensional calculations for the typical case of Gerry'sexperiment are presented. All the results coincide well with the experiment and are better thanthe results obtained in [1].In addition, the applicable scope of Lee's stable oscillation condition given by [1] is ex-panded; the condition for the approximation of gcometrical optics to be applied to mode con-structure in optical cavity is obtained for the first time and the difference between thiscondition and that for free space is also pointed out in the present work.

A short survey of the environment at the dumping site for Santa Cruz Harbor dredging and A study of seaward dipping internal structures in marine ripple marks at Whaler's Cove, California. Annual report, Part 4, August 1972

(PDF contains 76 pages)

Use of Sediment Bioassays to Verify Efficacy of Caulerpa taxifolia Eradication Treatments

Infestations of the marine macrophytic alga Caulerpa taxifolia were discovered in Agua Hedionda Lagoon, California in 2000. Rapid response actions included containment under pvc tarps coupled with injection of liquid sodium hypochlorite. To assess the efficacy of these treatments, replicated sediment cores were removed from representative treated sites and transferred to grow-out facilities. Similar cores from uninfested (control) sediments were removed, inoculated with viable explants of C. taxifolia and placed in grow-out facilities. Results from two sampling periods (1 year, 2 years post-treatment) showed that no viable C. taxifolia emerged in cores, and that inoculated “control” sediments supported normal growth. Eelgrass ( Zostera marina L.) seedlings emerged from native seed-banks in “treated” cores, which also supported growth of some invertebrates (annelid worms and hydroids). This study provided essential verification of C. taxifolia eradication efforts, and demonstrates the feasibility of incorporating quality control/quality assurance components in rapid response actions. Results of this study also suggest that seeds of eelgrass are viable for at least two years. (PDF has 9 pages.)

Effect of Aquathol K Treatments on Activity Patterns of Largemouth Bass in Two Coves of Lake Seminole, Georgia

Thirty largemouth bass ( Micropterus salmoide s Lacepde) were implanted with radio tags in late October 2003 in two coves of Lake Seminole, Georgia, and tracked over a 24-hour period about every 10 days to determine their response to herbicide application. After five weeks of tracking, hydrilla ( Hydrilla verticillata Royle) in each cove was treated in early December 2003 with dipotassium salt of endothall (Aquathol K; 7-oxabicyclo [2.2.1] heptane-2,3-dicarboxylic acid) at a rate of 3.5 ppm. Largemouth bass were tracked during application and tracking continued for three months post treatment to assess effects of herbicide treatment on activity patterns. The treatment in Desser Cove successfully reduced hydrilla in approximately half the cove. However, the treatment in Peacock Lake completely eliminated all submersed aquatic vegetation (SAV) by April 2004. Movement and activity centers remained similar between treatment periods in Desser Cove, but increased after treatment in Peacock Lake. Depth occupied by telemetered fish decreased after Aquathol K treatment in both coves. In general, behavior of largemouth bass did not change appreciably during treatment, and only minor changes were observed in the posttreatment period in Peacock Lake, where all SAV was eliminated. Fish showed little attraction to or movement away from treatment areas, and fish migration from either cove was nil after treatment. Application of Aquathol K and subsequent reduction of SAV had little effect on largemouth bass behavior or movement. (PDF has 8 pages.)

Non-target Impacts to Eelgrass from Treatments to Control Spartina in Willapa Bay, Washington

Four methods to control the smooth cordgrass Spartina (Spartina alterniflora) and the footwear worn by treatment personnelat several sites in Willapa Bay, Washington were evaluatedto determine the non-target impacts to eelgrass (Zostera japonica). Clone-sized infestations of Spartina were treated bymowing or a single hand-spray application of Rodeo® formulatedat 480 g L-1acid equivalence (ae) of the isopropylaminesalt of glyphosate (Monsanto Agricultural Co., St. Louis, MO;currently Dow AgroSciences, Indianapolis, IN) with the nonionic surfactant LI 700® (2% v/v) or a combination of mowing and hand spraying. An aerial application of Rodeo® with X-77 Spreader® (0.13% v/v) to a 2-ha meadow was also investigated. Monitoring consisted of measuring eelgrass shoot densities and percent cover pre-treatment and 1-yr post-treatment. Impacts to eelgrass adjacent to treated clones were determined 1 m from the clones and compared to a control 5-m away. Impacts from footwear were assessed at 5 equidistant intervals along a 10-m transect on mudflat and an untreated control transect at each of the three clone treatment sites. Impacts from the aerial application were determined by comparing shoot densities and percent cover 1, 3 and 10 m from the edge of the treated Spartina meadow to that at comparable distances from an untreated meadow. Methods utilized to control Spartina clones did not impact surrounding eelgrass at two of three sites. Decreases in shoot densities observed at the third site were consistent across treatments. Most impacts to eelgrass from the footwear worn by treatment personnel were negligible and those that were significant were limited to soft mud substrate. The aerial application of the herbicide was associated with reductions in eelgrass (shoot density and percent cover) at two of the three sampling distances, but reductions on the control plot were greater. We conclude that the unchecked spread of Spartina is a far greater threat to the survival and health of eelgrass than that from any of the control measures we studied. The basis for evaluating control measures for Spartina should be efficacy and logistical constraints and not impacts to eelgrass. PDF is 7 pages.

Influence of Dilute Acetic Acid Treatments on Survival of Monoecious Hydrilla Tubers in the Oregon House Canal, California

Hydrilla (Hydrilla verticillata (L.f.)Royle), a serious aquatic weed, reproduces through formation of underground tubers. To date, attacking this life-cycle stage has been problematic. The purpose of this study was to measure the impact of exposure to dilute acetic acid on monoecious hydrilla tubers under field conditions. In this field experiment, treatments were acetic acid concentration (0, 2.5, or 5%) and sediment condition (perforated or not perforated). Each of 60, 1x1 m plots (in the Oregon House Canal) were randomly assigned to one treatment. Two weeks after treatment, we collected three samples from each plot. One was washed over 2 mm wire mesh screens to separate tubers from sediment. Relative electrolyte leakage was measured for one tuber from each plot. Five additional tubers from each plot were placed in a growth chamber and sprouting monitored for four weeks. A second sample from each plot was placed in a plastic tub and placed in an outdoor tank, filled with water. These samples were monitored for tuber sprouting. Relative electrolyte leakage increased significantly for tubers exposed to 2.5% or 5% acetic acid. Effects on tubers in perforated sediment were reduced. Exposure to acetic acid inhibited tuber sprouting by 80 to 100%, in both chamber and outdoor tests. These results confirm findings from earlier laboratory/greenhouse experiments, and suggest that this approach may be useful in the management of hydrilla tuber banks in habitats where the water level can be lowered to expose the sediments.

Influence of Dilute Acetic Acid Treatments on American Pondweed Winter Buds in the Nevada Irrigation District, California

American pondweed ( Potamogeton nodosus Poir.) is commonly found in northern California irrigation canals. The purpose of this study was to test the hypothesis that exposure of American pondweed winter buds to dilute acetic acid under field conditions would result in reduced subsequent biomass.

Clearigate ® Treatments for Control of Giant Salvinia

Results of recent field trials using the chelated copper formulation Clearigate® 4 showed that applying a 20% solution by volume was effective for controlling populations of giant salvinia in irrigation canals. 5 Lower rates may be efficacious, thereby reducing chemical use and cost; however, little is known about the dose-response effects of Clearigate® against giant salvinia. The objective of this study was to determine the effective rate range of chelated copper applied as Clearigate® for control of giant salvinia.

Torsion fracture behavior of drawn pearlitic steel wires with different heat treatments

In this paper, torsion fracture behavior of drawn pearlitic steel wires with different heat treatments was investigated. Samples with different heat treatments was investigated. Samples with different heat treatment conditions were subjected to torsion and tensile tests. The shear strain along the torsion sample after fracture was measured. Fracture surface of wires was examined by Scanning Electron Microscopy. In addition, the method of Differential Scanning Calorimetry was used to characterize the thermodynamic process in the heat treatment. A numerical simulation via finite element method on temperature field evolution for the wire during heat treatment process was performed. The results show that both strain aging and recovery process occur in the material within the temperature range between room temperature and 435 degrees C. It was shown that the ductility measured by the number of twists drops at short heating times and recovers after further heating in the lead bath of 435 degrees C. On the other hand, the strenght of the wire increases at short heating times and decreases after further heating. The microstructure inhomogeneity due to short period of heat treatment, coupled with the gradient characteristics of shear deformation during torsion results in localized shear deformation of the wire. In this situation, shear cracks nucleate between lamella and the wire breaks with low number of twists.

Development of selection methods for steels and their heat treatments

Designers who want to manufacture a hardenable steel component need to select both the steel and its heat treatment. This project aims to develop a selection methodology for steels and process routes as an aid to designers. Three studies were conducted: - production of software to calculate the "equivalent diameter" and "equivalent Jominy distance" for simple shapes of a steel component; - prediction of semi-empirical Jominy curves (as-cooled) using CCT diagrams and process modelling methods, which were validated by experiment on plain carbon steels; - investigation of tempering of Jominy bars to explore the potential for semi-empirical models for the hardness after tempering.