Dimensionamento e sobreposição de nichos dos portunídeos (Decapoda, Brachyura), na Enseada da Fortaleza, Ubatuba, São Paulo, Brasil

The niche breadth of the Portunidae and their overlap on the subtidal sediments of Fortaleza bay, Ubatuba (São Paulo) was analyzed. Samples were made monthly from November/1988 to October/1989, inseven areas of the bay using a shrimp fishery boat equipped with two otter-trawls. Each area was characterized based on environmental factors such as depth, temperature, salinity, dissolved oxygen, organic matter and granulometric composition of the sediment. The number of individuais of each species was registered to each area (resource). Levins's standardized measure (BA) and niche percentage were calculated. Five species of swimming crabs were recorded in this study: Callinectes ornatus Ordway, 1863, Arenaeus cribrarius (Lamarck, 1818), Portunus spinimanus Latreille, 1819, Callinectes danae Smith, 1869 and Portunus spinicarpus (Stimpson, 1871). The widest ecological niche occurred to C. ornatus, present in all sampled areas (generalist species). Such fact can be related to high sediment tolerance when it is compared to P. spinimanus (especialist species) which was limited to the areas with coarse granulometric fractions. Highest niche overlap was verified between C. danae and A. cribrarius may be due to greater salinity tolerance of these species. The low occurrence of P. spinicarpus and its reduced niche size in Fortaleza Bay are due to association of this species to cold water currents (ACAS) more evidente in smaler depths during summer months. One future evaluation of the portunid diet can be useful to complement informations about this important aspect of the marine ecology.

Dimensionamento de amostras para monitoramento do ácaro da leprose Brevipalpus phoenicis (Geijskes, 1939) em citros

O controle do ácaro Brevipalpus phoenicis (Geijskes, 1939), transmissor do vírus da leprose, deve ser realizado quando sua população atinge o nível de ação, obtido pelo monitoramento de sua população, por meio de amostragens. Objetivou-se determinar o tamanho da amostra aceitável para estimar a população do ácaro, para posterior tomada de decisão. O experimento foi realizado na Fazenda Cambuhy, Matão - SP, no ano agrícola 2003-2004. Escolheu-se ao acaso um talhão da variedade Valência, com oito anos de idade, plantada no espaçamento 7x3,5m, com 2.480 plantas. Nesse talhão, foram inspecionados 1; 2; 3; 5; 10 e 100% das plantas, o que corresponde a 25; 50; 74; 124; 248 e 2.480 plantas, respectivamente, em caminhamento no sentido das linhas de plantio. Foram amostrados 3 frutos ou, na ausência destes, eram analisados ramos. de acordo com os resultados obtidos, observa-se que a porcentagem de erro na estimativa da média para a porcentagem de frutos com presença de ácaros, quando se amostra apenas 1% das plantas (25 plantas), é de 50%, ou seja, para uma infestação de 10%, a variação da porcentagem de frutos infestados estaria entre 5 e 15%, levando o produtor a subestimar ou a superestimar o nível de infestação, aumentando os gastos com pulverizações desnecessárias ou um controle ineficiente do ácaro. Para que o erro na amostragem fique dentro da situação aceitável, de 20 a 30% (em média 25%) de erro, deveriam ser amostradas 105 plantas. Na porcentagem de frutos com mais de 10 ácaros, verifica-se que, para a situação aceitável (20 a 30%), devem ser inspecionadas 540 plantas.

Parâmetros de dimensionamento para biodigestores batelada operados com dejetos de vacas leiteiras com e sem uso de inóculo

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Modelos para análise e dimensionamento de painéis de alvenaria estrutural

The main objective of this thesis was the study of bracing panels of structural masonry, by applying the Finite Element Method and Strut and Tie Method. It was analyzed the following aspects: the effect of orthotropy on the behavior of the panels; distribution of horizontal forces between panels for buildings; comparison between Equivalent Frame and Finite Elements models; panels design with the Strut and Tie Method. The results showed that one should not disregard the orthotropy, otherwise this can lead to models stiffer than the real. Regarding the distribution of horizontal forces, showed that the disregard of lintels and shear deformation leads to significant differences in the simplified model. The results showed also that the models in Finite Element and Equivalent Frame exhibit similar behavior in respect to stiffness of panels and stress distribution over the sessions requested. It was discussing criteria for designing Strut and Tie Method models in one floor panels. Then, the theoretical strength these panels was compared with the rupture strength of panels tested in the literature. The theoretical maximum strength were always less than the rupture strength of the panels obtained in tests, due to the fact that the proposed model cannot represent the behavior of the masonry after the start of the panel cracking due to plasticization of the reinforcement

Dimensionamento do número de amostras para avaliação da fertilidade do solo

The determination of the amount of sample units that will compose the sample express the optimization of the workforce, and reduce errors inherent in the report of recommendation and evaluation of soil fertility. This study aimed to determine in three systems use and soil management, the numbers of units samples design, needed to form the composed sample, for evaluation of soil fertility. It was concluded that the number of sample units needed to compose the composed sample to determination the attributes of organic matter, pH, P, K, Ca, Mg, Al and H+Al and base saturation of soil vary by use and soil management and error acceptable to the mean estimate. For the same depth of collected, increasing the number of sample units, reduced the percentage error in estimating the average, allowing the recommendation of 14, 14 and 11 sample in management with native vegetation, pasture cultivation and corn, respectively, for a error 20% on the mean estimate.

Análise de desempenho na rede metropolitana de saúde da Universidade Federal do Rio Grande do Norte : um dimensionamento aplicado a telemedicina e a telessaúde utilizando QoS baseado no padrão IEEE 802.1Q

It s notorious the advance of computer networks in recent decades, whether in relation to transmission rates, the number of interconnected devices or the existing applications. In parallel, it s also visible this progress in various sectors of the automation, such as: industrial, commercial and residential. In one of its branches, we find the hospital networks, which can make the use of a range of services, ranging from the simple registration of patients to a surgery by a robot under the supervision of a physician. In the context of both worlds, appear the applications in Telemedicine and Telehealth, which work with the transfer in real time of high resolution images, sound, video and patient data. Then comes a problem, since the computer networks, originally developed for the transfer of less complex data, is now being used by a service that involves high transfer rates and needs requirements for quality of service (QoS) offered by the network . Thus, this work aims to do the analysis and comparison of performance of a network when subjected to this type of application, for two different situations: the first without the use of QoS policies, and the second with the application of such policies, using as scenario for testing, the Metropolitan Health Network of the Federal University of Rio Grande do Norte (UFRN)

Dimensionamento de sistemas de aterramento em linhas de transmissão para escoamento eficiente de correntes de surtos atmosféricos

This work presents in a simulated environment, to analyze the length of cable needed counterweight connected to ground rod, able to avoid the phenomenon of flashover return, back flashover, the insulator chains of transmission lines consisting of concrete structures when they are subjected to lightning standardized regarding certain resistivity values of some kinds of soil and geometric arrangements of disposal of grounding systems structures

Ensaios de tratabilidade aplicados a determinação de parâmetros para dimensionamento de processos de tratamento de água de manancial eutrofizado

Eutrophication is a growing process present in the water sources located in the northeast of Brazil. Among the main consequences of these changes in trophic levels of a water source, stands out adding complexity to the treatment to achieve water standards. By these considerations, this study aimed to define, on a laboratory scale, products and operational conditions to be applied in the processing steps using raw water from Gargalheiras dam, RN, Brazil. The dam mentioned shows a high number of cyanobacteria, with a concentration of cells / ml higher than that established by Decree No. 518/04 MS. The same source was also considered by the state environmental agency in 2009 as hypereutrophic. The static tests developed in this research simulated direct filtration (laboratory filters) and pre-oxidation with chlorine and powdered activated carbon adsorption. The research included the evaluation of the coagulants aluminum hydrochloride (HCA) and alum (SA). The development of the research investigated the conditions for rapid mixing, the dosages of coagulants and pHs of coagulation by the drawing of diagrams. The interference of filtration rate and particle size of filtering means were evaluated as samples and the time of contact were tested with chlorine and activated carbon. By the results of the characterization of the raw water source it was possible to identify the presence of a high pH (7.34). The true color was significant (29 uH) in relation to the apparent color and turbidity (66 uH and 13.60 NTU), reflecting in the measurement of organic matter: MON (8.41 mg.L-1) and Abs254 (0.065 cm-1). The optimization of quick mix set time of 17", the speed gradient of 700 s-1 in the coagulation with HCA and the time of 20" with speed gradient of 800 s-1 for SA. The smaller particle sizes of sand filtering means helped the treatment and the variation in filtration rate did not affect significantly the efficiency of the process. The evaluation of the processing steps found adjustment in standard color and turbidity of the Decree nº 518/04 MS, taking in consideration the average values found in raw water. In the treatment using the HCA for direct filtration the palatable pattern based on the apparent color can be achieved with a dose of 25 mg L-1. With the addition of pre-oxidation step, the standard result was achieved with a reduced dose for 12 mgHCA.L-1. The turbidity standard for water was obtained by direct filtration when the dose exceeds 25 mg L-1 of HCA. With pre-oxidation step there is the possibility of reducing the dose to 20 mg L-1.The addition of CAP adsorption, promoted drinking water for both parameters, with even lower dosage, 13 mg L-1 of HCA. With coagulation using SA removal required for the parameter of apparent color it was achieved with pre-oxidation and 22 mgSA.L-1. Despite the satisfactory results of treatment with the alum, it was not possible to provide water with turbidity less than 1.00 NTU even with the use of all stages of treatment

Sistema especialista fuzzy para dimensionamento de bombeio mecânico

Despite the emergence of other forms of artificial lift, sucker rod pumping systems remains hegemonic because of its flexibility of operation and lower investment cost compared to other lifting techniques developed. A successful rod pumping sizing necessarily passes through the supply of estimated flow and the controlled wear of pumping equipment used in the mounted configuration. However, the mediation of these elements is particularly challenging, especially for most designers dealing with this work, which still lack the experience needed to get good projects pumping in time. Even with the existence of various computer applications on the market in order to facilitate this task, they must face a grueling process of trial and error until you get the most appropriate combination of equipment for installation in the well. This thesis proposes the creation of an expert system in the design of sucker rod pumping systems. Its mission is to guide a petroleum engineer in the task of selecting a range of equipment appropriate to the context provided by the characteristics of the oil that will be raised to the surface. Features such as the level of gas separation, presence of corrosive elements, possibility of production of sand and waxing are taken into account in selecting the pumping unit, sucker-rod strings and subsurface pump and their operation mode. It is able to approximate the inferente process in the way of human reasoning, which leads to results closer to those obtained by a specialist. For this, their production rules were based on the theory of fuzzy sets, able to model vague concepts typically present in human reasoning. The calculations of operating parameters of the pumping system are made by the API RP 11L method. Based on information input, the system is able to return to the user a set of pumping configurations that meet a given design flow, but without subjecting the selected equipment to an effort beyond that which can bear

BMMobile: uma linha de produtos para dimensionamento de bombeio mecânico em dispositivos móveis

With the increase of processing ability, storage and several kinds of communication existing such as Bluetooth, infrared, wireless networks, etc.., mobile devices are no longer only devices with specific function and have become tools with various functionalities. In the business field, the benefits that these kinds of devices can offer are considerable, because the portability allows tasks that previously could only be performed within the work environment, can be performed anywhere. In the context of oil exploration companies, mobile applications allow quick actions could be taken by petroleum engineers and technicians, using their mobile devices to avoid potential catastrophes like an unexpected stop or break of important equipment. In general, the configuration of equipment for oil extraction is performed on the work environment using computer systems in desktop platforms. After the obtained configuration, an employee goes to equipment to be configured and perform the modifications obtained on the use desktop system. This management process equipment for oil extraction takes long time and does not guarantee the maintenance in time to avoid problems. With the use of mobile devices, management and maintenance of equipment for oil extraction can be performed in a more agile time once it enables the engineer or technician oil can perform this configuration at the time and place where the request comes for example, near in the oil well where the equipment is located. The wide variety of mobile devices creates a big difficulty in developing mobile applications, since for one application can function in several types of devices, the application must be changed for each specific type of device, which makes the development quite costly. This paper defines and implements a software product line for designing sucker-rod pumping systems on mobile devices. This product line of software, called BMMobile, aims to produce products that are capable of performing calculations to determine the possible configurations for the equipment in the design suckerrod pumping, and managing the variabilities of the various products that can be generated. Besides, this work performs two evaluations. The first evaluation will verify the consistency of the products produced by the software product line. The second evaluation will verify the reuse of some products generated by SPL developed

Desenvolvimento de um sistema computacional para dimensionamento e evolução de rebanhos bovinos

Os objetivos deste estudo foram desenvolver um sistema computacional que efetue o dimensionamento e a evolução de rebanhos bovinos e criar uma ferramenta que possibilite ao usuário efetuar simulações em um sistema de produção de carne e/ou leite. Foi utilizada a linguagem CA Clipper. As rotinas foram desenvolvidas de forma conversacional, com acesso aos diversos programas, por meio de menus auto-explicativos. O sistema desenvolvido pode auxiliar o técnico e o pecuarista no dimensionamento e na evolução de um rebanho bovino com precisão e considerável rapidez; possibilita ao usuário efetuar inúmeras simulações; e constitui -se em importante ferramenta no auxílio da tomada de decisões.

Nova proposta de critério de retenção para dimensionamento de filtros têxteis

The designs of filters made by granular material or textile are mainly based on empirical or semi empirical retention criteria according to Terzaghi proposal, which compares particle diameter of the soil base with the filter porous spaces. Silveira in 1965, proposed one rational design retention criteria based on the probability of a particle from the soil base, carried by one dimensional flow, be restrained by the porous of the filter while trying to pass through its thickness. This new innovating theory, besides of being very simple, it is not frequently used for granular filters since the necessary parameters for the design has to be determine for each natural material. However, for textile this problem no longer exists because it has quality control during manufacturing and the necessary characteristics properties of the product are specify in the product catalog. This work presents one adaptation of the Silveira theory for textile filters and the step-by-step procedure for the determination of the characteristics properties of the textile products necessary for the design. This new procedure permits the determination of the confiability level of retention that one specific particle diameter form the soil base has for one specified textile. One complete example is presented to demonstrate the simplicity of the method proposed and how the textile characteristics are obtained.

Reformulação para um problema integrado de dimensionamento e sequenciamento de lotes

In this paper, some new constraints and an extended formulation are presented for a Lot Sizing and Scheduling Model proposed in the literature. In the production process considered a key material is prepared and is transformed into different final items. The sequencing decisions are related to the order in which the materials are processed and the lot sizing decisions are related to the final items production. The mathematical formulation considers sequence-dependent setup costs and times. Results of the computational tests executed using the software Cplex 10.0 showed that the performance of the branch-and-cut method can be improved by the proposed a priori reformulation.

Modelos matemáticos para problemas de dimensionamento de lotes com restrições de capacidade e custos de transporte

In this paper, capacitated lot sizing problems in which the classical lot sizing decisions are made considering the transportation costs of the manufactured products were studied. These costs are related to the necessary number of pallets or trucks to pack and/or transport the products from the factory to the warehouse. Three extensions of a mixed integer linear programming model from the literature are considered, representing general cases that are commonly found in companies. These models are tested and evaluated using an optimization package, and a Lagrangian heuristic was developed for one of the extensions proposed.

Modelos matemáticos para o problema integrado de dimensionamento de lotes e corte de estoque undimensional

Pós-graduação em Matemática - IBILCE