Evaluation of dichroic material for enhancing light pipe/natural ventilation and daylighting in an integrated system

Integration of natural ventilation and daylighting in a single installation would make both technologies more attractive. One method for the integration is the use of concentric light pipe and ventilation stack. By constructing the light pipe using dichroic materials, the infrared part of the solar radiation is allowed to be transmitted to the stack but the visible light is guided by the light pipe into a room. The heat gain to the interior can be reduced and the thermal stack effect strengthened. Work presented here involved the experimental and computational evaluation of dichroic materials for enhancing both natural stack ventilation and daylighting. The transmittance of a dichroic light pipe was found to be similar to that of a light pipe with a 95% specular reflectance. The infra-red radiation transmitted through the dichroic material into a passive stack was found to enhance the natural ventilation flow by up to 14%. The effect is greater in summer than in winter, which is highly desirable as there is often a lack of driving force for natural stack ventilation in summer.

The British state and the Irish rebellion of 1916: an intelligence failure or an failure of response

The teleological narrative that has dominated the handling of intelligence by the British state in the events that led up to the 1916 Irish Rebellion in Dublin has been characterised as a cocktail of incompetence and mendacity. Using new and existing archive material this article argues that both the cabinet in London and key members of the Irish Executive in Dublin were supplied with accurate and timely intelligence by the Admiralty's signals intelligence unit, the Royal Irish Constabulary and the Dublin Metropolitan Police with respect to this event. Far from being a failure of intelligence here is evidence to show that there occurred a failure of response on behalf of key decision-makers. The warnings that were given by intelligence organisations were filtered through the existing policy preferences and assumptions. As a result of these factors accurate evaluations and sound judgement were not exercised by key officials, such as Sir Matthew Nathan, in Dublin Castle.

Success and failure of grassroots innovations for addressing climate change: the case of the Transition Movement

Grassroots innovations emerge as networks generating innovative solutions for climate change adaptation and mitigation. However, it is unclear if grassroots innovations can be successful in responding to climate change. Little evidence exists on replication, international comparisons are rare, and research tends to overlook discontinued responses in favour of successful ones. We take the Transition Movement as a case study of a rapidly spreading transnational grassroots network, and include both active and non-active local transition initiatives. We investigate the replication of grassroots innovations in different contexts with the aim to uncover general patterns of success and failure, and identify questions for future research. An online survey was carried out in 23 countries (N=276). The data analysis entailed testing the effect of internal and contextual factors of success as drawn from the existing literature, and the identification of clusters of transition initiatives with similar internal and contextual factor configurations. Most transition initiatives consider themselves successful. Success is defined along the lines of social connectivity and empowerment, and external environmental impact. We find that less successful transition initiatives might underestimate the importance of contextual factors and material resources in influencing success. We also find that their diffusion is linked to the combination of local-global learning processes, and that there is an incubation period during which a transition initiative is consolidated. Transition initiatives seem capable of generalising organisational principles derived from unique local experiences that seem to be effective in other local contexts. However, the geographical locations matter with regard to where transition initiatives take root and the extent of their success, and ‘place attachment’ may have a role in the diffusion of successful initatives. We suggest that longitudinal comparative studies can advance our understanding in this regard, as well as inform the changing nature of the definition of success at different stages of grassroots innovation development, and the dynamic nature of local and global linkages.

Experimental and computational investigation of the roll forming process

One of the first questions to consider when designing a new roll forming line is the number of forming steps required to produce a profile. The number depends on material properties, the cross-section geometry and tolerance requirements, but the tool designer also wants to minimize the number of forming steps in order to reduce the investment costs for the customer. There are several computer aided engineering systems on the market that can assist the tool designing process. These include more or less simple formulas to predict deformation during forming as well as the number of forming steps. In recent years it has also become possible to use finite element analysis for the design of roll forming processes. The objective of the work presented in this thesis was to answer the following question: How should the roll forming process be designed for complex geometries and/or high strength steels? The work approach included both literature studies as well as experimental and modelling work. The experimental part gave direct insight into the process and was also used to develop and validate models of the process. Starting with simple geometries and standard steels the work progressed to more complex profiles of variable depth and width, made of high strength steels. The results obtained are published in seven papers appended to this thesis. In the first study (see paper 1) a finite element model for investigating the roll forming of a U-profile was built. It was used to investigate the effect on longitudinal peak membrane strain and deformation length when yield strength increases, see paper 2 and 3. The simulations showed that the peak strain decreases whereas the deformation length increases when the yield strength increases. The studies described in paper 4 and 5 measured roll load, roll torque, springback and strain history during the U-profile forming process. The measurement results were used to validate the finite element model in paper 1. The results presented in paper 6 shows that the formability of stainless steel (e.g. AISI 301), that in the cold rolled condition has a large martensite fraction, can be substantially increased by heating the bending zone. The heated area will then become austenitic and ductile before the roll forming. Thanks to the phenomenon of strain induced martensite formation, the steel will regain the martensite content and its strength during the subsequent plastic straining. Finally, a new tooling concept for profiles with variable cross-sections is presented in paper 7. The overall conclusions of the present work are that today, it is possible to successfully develop profiles of complex geometries (3D roll forming) in high strength steels and that finite element simulation can be a useful tool in the design of the roll forming process.

Um modelo analítico e computacional para consideração de efeitos de envelhecimento em estruturas de material compósito

Os materiais compósitos reforçados por fibras apresentam vantagens quando comparados aos materiais de construção mais tradicionais como concreto e aço. Por outro lado, devido ao fato destes materiais serem relativamente recentes no mercado, questões a respeito de sua durabilidade são ainda objeto de discussão e faz-se necessária intensa pesquisa sobre o envelhecimento dos compósitos. Como conseqüência, recentemente têm surgido inúmeros trabalhos à respeito da degradação dos compósitos considerando efeitos como temperatura, oxidação, radiação UV, condições de carregamento, etc. A maioria destas pesquisas, no entanto, são realizadas a nível de material e não são diretamente aplicáveis à situações de projeto. Desta forma, existe grande demanda por novos estudos e dados compatíveis com aplicações estruturais. Neste trabalho apresenta-se um modelo analítico-numérico adequado para, interpretação e aplicação destes dados experimentais em análise e projeto de estrutural. A formulação proposta inclui relações constitutivas elásticas anisotrópicas com envelhecimento, relações constitutivas viscoelásticas anisotrópicas com envelhecimento em termos de variáveis de estado, análise de falhas com critério de degradação ajustado à idade do material e considera-se grandes deslocamentos e pequenas deformações. As diferenças essenciais entre os processos de envelhecimento em endurecimento e amolecimento são descritos juntamente com as relações constitutivas para cada caso. Estas equações são deduzidas na forma adequada para análise numérica via método dos elementos finitos usando uma solução incremental-iterativa com consideração de efeitos pos-críticos. Vários exemplos são apresentados, incluindo análises elásticas, viscoelásticas e de falha com envelhecimento.

Desenvolvimento de um ressoador retangular de fenda com múltiplas camadas de substrato e com utilização de material PBG para sistema de comunicação sem fio

In the globalized world modern telecommunications have assumed key role within the company, causing a large increase in demand for the wireless technology of communication, which has been happening in recent years have greatly increased the number of applications using this technology. Due to this demand, new materials are developed to enable new control mechanisms and propagation of electromagnetic waves. The research to develop new technologies for wireless communication presents a multidisciplinary study that covers from the new geometries for passive antennas, active up to the development of materials for devices that improve the performance at the frequency range of operation. Recently, planar antennas have attracted interest due to their characteristics and advantages when compared with other types of antennas. In the area of mobile communications the need for antennas of this type has become increasingly used, due to intensive development, which needs to operate in multifrequency antennas and broadband. The microstrip antennas have narrow bandwidth due to the dielectric losses generated by irradiation. Another limitation is the degradation of the radiation pattern due to the generation of surface waves in the substrate. Some techniques have been developed to minimize this limitation of bandwidth, such as the study of type materials PBG - Photonic Band Gap, to form the dielectric material. This work has as main objective the development project of a slot resonator with multiple layers and use the type PBG substrate, which carried out the optimization from the numerical analysis and then designed the device initially proposed for the band electromagnetic spectrum between 3-9 GHz, which basically includes the band S to X. Was used as the dielectric material RT/Duroid 5870 and RT/Duroid 6010.LM where both are laminated ceramic-filled PTFE dielectric constants 2.33 and 10.2, respectively. Through an experimental investigation was conducted an analysis of the simulated versus measured by observing the behavior of the radiation characteristics from the height variation of the dielectric multilayer substrates. We also used the LTT method resonators structures rectangular slot with multiple layers of material photonic PBG in order to obtain the resonance frequency and the entire theory involving the electromagnetic parameters of the structure under consideration. xviii The analysis developed in this work was performed using the method LTT - Transverse Transmission Line, in the field of Fourier transform that uses a component propagating in the y direction (transverse to the real direction of propagation z), thus treating the general equations of the fields electric and magnetic and function. The PBG theory is applied to obtain the relative permittivity of the polarizations for the sep photonic composite substrates material. The results are obtained with the commercial software Ansoft HFSS, used for accurate analysis of the electromagnetic behavior of the planar device under study through the Finite Element Method (FEM). Numerical computational results are presented in graphical form in two and three dimensions, playing in the parameters of return loss, frequency of radiation and radiation diagram, radiation efficiency and surface current for the device under study, and have as substrates, photonic materials and had been simulated in an appropriate computational tool. With respect to the planar device design study are presented in the simulated and measured results that show good agreement with measurements made. These results are mainly in the identification of resonance modes and determining the characteristics of the designed device, such as resonant frequency, return loss and radiation pattern

A computational tool to assist the analysis of the transformer behavior related to lightning

This paper proposes the application of computational intelligence techniques to assist complex problems concerning lightning in transformers. In order to estimate the currents related to lightning in a transformer, a neural tool is presented. ATP has generated the training vectors. The input variables used in Artificial Neural Networks (ANN) were the wave front time, the wave tail time, the voltage variation rate and the output variable is the maximum current in the secondary of the transformer. These parameters can define the behavior and severity of lightning. Based on these concepts and from the results obtained, it can be verified that the overvoltages at the secondary of transformer are also affected by the discharge waveform in a similar way to the primary side. By using the tool developed, the high voltage process in the distribution transformers can be mapped and estimated with more precision aiding the transformer project process, minimizing empirics and evaluation errors, and contributing to minimize the failure rate of transformers. (C) 2011 Elsevier Ltd. All rights reserved.

3-D reconstruction by extended depth-of-field in failure analysis - Case study II: Fractal analysis of interlaminar fracture in carbon/epoxy composites

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A preparação de material terminológico em língua inglesa por meio de ferramentas linguístico-computacionais

O objetivo desse estudo é demonstrar, por meio de análise quantitativa e qualitativa, a eficácia de ferramentas linguístico-computacionais na seleção de terminologia para a produção de material terminológico. Serão apresentadas duas ferramentas linguístico-computacionais (WordSmith Tools e VocabProfile) e, também, sugestões para que o ensino de termos ofereça resultados práticos. A fundamentação teórico-metodológica recorreu a Barros (2004); Berber Sardinha (2000; 2005); Biderman (2001); Cabré (2007); Cobb (2007); Nation, (2003) e Sinclair (2004). O corpus da pesquisa foi constituído exclusivamente de material escrito na língua inglesa em diversas áreas de especialidade. Os procedimentos de preparação de material terminológico são exemplificados a partir de uma das áreas de especialidades utilizadas nos corpora de pesquisa, as Redes Neurais Artificiais. Os resultados obtidos indicam que a utilização do Wordsmith Tools juntamente com o VocabProfile pode fornecer dados importantes para a pesquisa linguistica.

Growth mechanism of octahedron-like BaMoO4 microcrystals processed in microwave-hydrothermal: Experimental observations and computational modeling

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Cocaine associated with onlay bone graft failure: A clinical and histologic report

This patient report presents an unusual onlay bone graft failure following local cocaine application. Three months after the bone grafting procedure performed in the anterior maxilla for bone volume augmentation, the bone graft was totally exposed in the oral cavity as a result of the rubbing of cocaine on the gingival tissue that covered the bone graft. A histologic view of the removed bone fragment presented not only an area of necrosis but also ample spaces filled with necrosis material and resorption areas. Dental practitioners need to be aware of this phenomenon because such patients often do not report the use of drugs, particularly cocaine. Copyright © 2005 by Lippincott Williams & Wilkins.

Determinação física e numérica de corridas de lama resultantes de ruptura de barreira retendo material viscoplástico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Perfil epidemiológico de acidentes com material biológico entre estudantes de medicina em um pronto-socorro cirúrgico

OBJECTIVE: To evaluate the accidents with biological material among medical students interning in a trauma emergency room and identify key related situations, attributed causes and prevention. METHODS: we conducted a study with a quantitative approach. Data were collected through a questionnaire applied via internet, with closed, multiple-choice questions regarding accidents with biological material. The sample comprised 100 students. RESULTS: thirty-two had accidents with biological material. Higher-risk activities were local anesthesia (39.47%), suture (18.42%) and needle recapping (15.79%). The main routes of exposure to biological material were the eyes or mucosa, with 34%, and syringe needle puncture, with 45%. After contamination, only 52% reported the accident to the responsible department. CONCLUSION: The main causes of accidents and routes of exposure found may be attributed to several factors, such as lack of training and failure to use personal protective equipment. Educational and preventive actions are extremely important to reduce the incidence of accidents with biological materials and improve the conduct of post-exposure. It is important to understand the main causes attributed and situations related, so as general and effective measures can be applied.

Proteins, Pathogens, and Failure at the Composite-Tooth Interface

In the United States, composites accounted for nearly 70% of the 173.2 million composite and amalgam restorations placed in 2006 (Kingman et al., 2012), and it is likely that the use of composite will continue to increase as dentists phase out dental amalgam. This trend is not, however, without consequences. The failure rate of composite restorations is double that of amalgam (Ferracane, 2013). Composite restorations accumulate more biofilm, experience more secondary decay, and require more frequent replacement. In vivo biodegradation of the adhesive bond at the composite-tooth interface is a major contributor to the cascade of events leading to restoration failure. Binding by proteins, particularly gp340, from the salivary pellicle leads to biofilm attachment, which accelerates degradation of the interfacial bond and demineralization of the tooth by recruiting the pioneer bacterium Streptococcus mutans to the surface. Bacterial production of lactic acid lowers the pH of the oral microenvironment, erodes hydroxyapatite in enamel and dentin, and promotes hydrolysis of the adhesive. Secreted esterases further hydrolyze the adhesive polymer, exposing the soft underlying collagenous dentinal matrix and allowing further infiltration by the pathogenic biofilm. Manifold approaches are being pursued to increase the longevity of composite dental restorations based on the major contributing factors responsible for degradation. The key material and biological components and the interactions involved in the destructive processes, including recent advances in understanding the structural and molecular basis of biofilm recruitment, are described in this review. Innovative strategies to mitigate these pathogenic effects and slow deterioration are discussed.

Inlays Made From a Hybrid Material: Adaptation and Bond Strengths

The aim of this study was to evaluate the internal fit, marginal adaptation, and bond strengths of inlays made of computer-aided design/computer-aided manufacturing feldspathic ceramic and polymer-infiltrated ceramic. Twenty molars were randomly selected and prepared to receive inlays that were milled from both materials. Before cementation, internal fit was achieved using the replica technique by molding the internal surface with addition silicone and measuring the cement thicknesses of the pulpal and axial walls. Marginal adaptation was measured on the occlusal and proximal margins of the replica. The inlays were then cemented using resin cement (Panavia F2.0) and subjected to two million thermomechanical cycles in water (200 N load and 3.8-Hz frequency). The restored teeth were then cut into beams, using a lathe, for microtensile testing. The contact angles, marginal integrity, and surface patterns after etching were also observed. Statistical analysis was performed using two-way repeated measures analysis of variance (p<0.05), the Tukey test for internal fit and marginal adaptation, and the Student t-test for bond strength. The failure types (adhesive or cohesive) were classified on each fractured beam. The results showed that the misfit of the pulpal walls (p=0.0002) and the marginal adaptation (p=0.0001) of the feldspathic ceramic were significantly higher when compared to those of the polymer-infiltrated ceramic, while the bond strength values of the former were higher when compared to those of the latter. The contact angle of the polymer-infiltrated ceramic was also higher. In the present study, the hybrid ceramic presented improved internal and marginal adaptation, but the bond strengths were higher for the feldspathic ceramic.