Speciation of naturally-accumulated uranium in an organic-rich soil of an alpine region (Switzerland)

Very high concentrations of uranium (up to 4000 ppm) were found in a natural soil in the Dischma valley, an alpine region in the Grisons canton in Switzerland. The goal of this study was to examine the redox state and the nature of uranium binding in the soil matrix in order to understand the accumulation mechanism. Pore water profiles collected from Dischma soil revealed the establishment of anoxic conditions with increasing soil depth. A combination of chemical extraction methods and spectroscopy was applied to characterize the redox state and binding environment of uranium in the soil. Bicarbonate extraction under anoxic conditions released most of the uranium indicating that uranium occurs predominantly in the hexavalent form. Surprisingly, the uranium redox state did not vary greatly as a function of depth. X-ray absorption near edge spectroscopy (XANES), confirmed that uranium was present as a mixture of U(VI) and U(IV) with U(VI) dominating. Sequential extractions of soil samples showed that the dissolution of solid organic matter resulted in the simultaneous release of the majority of the soil uranium content (>95%). Extended X-ray absorption fine structure (EXAFS) spectroscopy also revealed that soil-associated uranium in the soil matrix was mainly octahedrally coordinated, with an average of 1.7 axial (at about 1.76 Å) and 4.6 to 5.3 equatorial oxygen atoms (at about 2.36 Å) indicating the dominance of a uranyl-like (UO22+) structure presumably mixed with some U(IV). An additional EXAFS signal (at about 3.2 Å) identified in some spectra suggested that uranium was also bound (via an oxygen atom) to a light element such as carbon, phosphorus or silicon. Gamma spectrometric measurements of soil profiles failed to identify uranium long-life daughter products in the soil which is an indication that uranium originates elsewhere and was transported to its current location by water. Finally, it was found that the release of uranium from the soil was significantly promoted at very low pH values (pH 2) and increased with increasing pH values (between pH 5 and 9).

On-line desorption of dried blood spot: A novel approach for the direct LC/MS analysis of micro-whole blood samples.

The aim of this work is to present a new concept, called on-line desorption of dried blood spots (on-line DBS), allowing the direct analysis of a dried blood spot coupled to liquid chromatography mass spectrometry device (LC/MS). The system is based on an inox cell which can receive a blood sample (10 microL) previously spotted on a filter paper. The cell is then integrated into LC/MS system where the analytes are desorbed out of the paper towards a column switching system ensuring the purification and separation of the compounds before their detection on a single quadrupole MS coupled to atmospheric pressure chemical ionisation (APCI) source. The described procedure implies that no pretreatment is necessary in spite the analysis is based on whole blood sample. To ensure the applicability of the concept, saquinavir, imipramine, and verapamil were chosen. Despite the use of a small sampling volume and a single quadrupole detector, on-line DBS allowed the analyses of these three compounds over their therapeutic concentrations from 50 to 500 ng/mL for imipramine and verapamil and from 100 to 1000 ng/mL for saquinavir. Moreover, the method showed good repeatability with relative standard deviation (RSD) lower than 15% based on two levels of concentration (low and high). Function responses were found to be linear over the therapeutic concentration for each compound and were used to determine the concentrations of real patient samples for saquinavir. Comparison of the founded values with those of a validated method used routinely in a reference laboratory showed a good correlation between the two methods. Moreover, good selectivity was observed ensuring that no endogenous or chemical components interfered with the quantitation of the analytes. This work demonstrates the feasibility and applicability of the on-line DBS procedure for bioanalysis.

Reproducing the organic matter model of anthropogenic dark earth of Amazonia and testing the ecotoxicity of functionalized charcoal compounds

The objective of this work was to obtain organic compounds similar to the ones found in the organic matter of anthropogenic dark earth of Amazonia (ADE) using a chemical functionalization procedure on activated charcoal, as well as to determine their ecotoxicity. Based on the study of the organic matter from ADE, an organic model was proposed and an attempt to reproduce it was described. Activated charcoal was oxidized with the use of sodium hypochlorite at different concentrations. Nuclear magnetic resonance was performed to verify if the spectra of the obtained products were similar to the ones of humic acids from ADE. The similarity between spectra indicated that the obtained products were polycondensed aromatic structures with carboxyl groups: a soil amendment that can contribute to soil fertility and to its sustainable use. An ecotoxicological test with Daphnia similis was performed on the more soluble fraction (fulvic acids) of the produced soil amendment. Aryl chloride was formed during the synthesis of the organic compounds from activated charcoal functionalization and partially removed through a purification process. However, it is probable that some aryl chloride remained in the final product, since the ecotoxicological test indicated that the chemical functionalized soil amendment is moderately toxic.

Characterization of board impurities with a Raman device

Erilaisia epäpuhtauksia kulkeutuu paperinvalmistusprosessiin ja monenlaisia saostumia muodostuu paperinvalmistuksen prosesseissa. Epäpuhtaudet voivat aiheuttaa prosessiongelmia sekä alentaa tuotteen laatua. Epäpuhtauksien alkuperän ja koostumuksen selvittäminen edellyttää usein erilaisten analyysimenetelmien käyttöä. Epäpuhtauksien luokittelu on useasti välttämätöntä ennen tarkempaa kemiallista analyysia. Paperinvalmistuksen epäpuhtauksien kvalitatiiviseen luokitteluun on yleisimmin käytetty mikroskopian, IR-spektroskopian ja analyyttisen pyrolyysin menetelmiä. Raman spektroskopia on harvinaisempi menetelmä paperiteollisuuden tutkimuksessa. Raman instrumenttien kehittyminen on ollut voimakasta viimeisen vuosikymmenen aikana. Raman spektroskopia onkin osoittanut mandollisuutensa polymeerien, lääketeollisuuden ja polttoaineteollisuuden tutkimuksissa. Tässä työssä tutkittiin erään elintarvikepakkauskartongin epäpuhtauksia Raman spektroskoopilla. Työn tavoitteena oli selvittää Raman analyysin käyttökelpoisuutta kartongin epäpuhtauksien online-luokittelussa. Tutkimukset suoritettiin Spectracoden RP-1 Raman instrumentilla. Tutkimukset osoittivat, että näytteen fluoresenssi ja näytteen hajoaminen asettavat rajoituksia epäpuhtauksien Raman analyysille. Epäpuhtauksien online-tunnistaminen toimii käytettäessä suuria lasertehoja ja säteilytysaikoja. Näytteiden laserherkkyys ja fluoresenssi rajoittavat kuitenkin suurien laiteparametrien käyttöä. Laiteparametrien pienentäminen johti mittauksien signaali-kohina suhteen alenemiseen, mikä puolestaan aiheutti online-tunnistuksen toimimattomuuden.

Desenvolvimento e caracterização de recobrimentos de Ni-Co e de seus óxidos mistos para a produção de oxigênio por eletrólise alcalina da água

This paper describes the development and characterisation of Ni-Co coatings to be used as anodes in water electrolysis. Chemical oxidation of the surface was performed through thermal treatment at 400ºC for 10 h. The resulting surfaces were analysed by X-ray diffraction, EDX, SEM, cyclic voltammetry and constant current electrolysis. The electrochemical oxidation occurring on bare surfaces during electrolysis promotes the formation of thick oxide layers resulting in loss of activity. In oxidised surfaces the chemical Ni-Co oxide grown during the thermal treatment prevents further oxidation thus retaining their activity towards oxygen evolution. An optimum condition for the growth of mixed oxide with high activity was found for the bath containing 50 g L-1 CoSO4.

Looking beneath Dalí's paint: non-destructive canvas analysis

A new analytical method was developed to non-destructively determine pH and degree of polymerisation (DP) of cellulose in fibres in 19th 20th century painting canvases, and to identify the fibre type: cotton, linen, hemp, ramie or jute. The method is based on NIR spectroscopy and multivariate data analysis, while for calibration and validation a reference collection of 199 historical canvas samples was used. The reference collection was analysed destructively using microscopy and chemical analytical methods. Partial least squares regression was used to build quantitative methods to determine pH and DP, and linear discriminant analysis was used to determine the fibre type. To interpret the obtained chemical information, an expert assessment panel developed a categorisation system to discriminate between canvases that may not be fit to withstand excessive mechanical stress, e.g. transportation. The limiting DP for this category was found to be 600. With the new method and categorisation system, canvases of 12 Dalí paintings from the Fundació Gala-Salvador Dalí (Figueres, Spain) were non-destructively analysed for pH, DP and fibre type, and their fitness determined, which informs conservation recommendations. The study demonstrates that collection-wide canvas condition surveys can be performed efficiently and non-destructively, which could significantly improve collection management.

Remoção do ácido mefenâmico em água utilizando carvão ativado em pó, lama vermelha e oxidação com cloro

The use of activated carbon powder (ACP), red mud and oxidation with chlorine to remove mefenamic acid in water are described, aimed at their application as a complement to sewage treatment processes in Brazil. A study on the behavior of mefenamic acid in water was performed by evaluating its dissolution for different concentrations and times. Subsequently, the optimal conditions for removal of mefenamic acid were investigated using ACP adsorption at different pH and concentrations, and red mud adsorption using different pH. The utilization of different pH and times was also investigated to establish the ideal conditions for chemical oxidation of the drug. Among the different conditions studied, the best condition for drug removal by ACP and red mud were 100% and 96%, respectively, while the best condition for chemical oxidation occurred using solutions with pH 6 and 7 and reaction times of 30 and 60 minutes.

ARSÊNIO E ARROZ: TOXICIDADE, METABOLISMO E SEGURANÇA ALIMENTAR

Arsenic is considered a semimetal, and its wide distribution in the Earth's crust in different chemical forms, including organic and inorganic species, has a great deal of influence on the mechanisms of toxicity. Exposure to arsenic can be either through occupational practice (use of pesticides) or by the consumption of water and food containing the element. Rice is considered a fundamental constituent of the basic diet of Brazilians and is usually cultivated in flooded conditions. Such a plantation system results in an increased amount of As in the soil and hence a greater accumulation of As in the plant, which is highlighted by the inorganic species' classification as highly toxic. Besides the use of mitigation techniques to reduce the toxicological risk, monitoring the concentration of As and its chemical species in rice and rice products is required through the establishment of legislation in the area. Thus, some world organizations are conducting improved research to determine and establish acceptable concentrations of As and its chemical species in rice, e. g., in 2012, FDA researchers described a chemical speciation methodology for As in rice and rice products. Hence, the application of existing chemical speciation methods and the establishment of parameters for ensuring food security and exposure risk assessment deserve particular consideration.

Does cotinine act upon reactive oxygen species and peroxidases?

Nicotine, an oxidizing agent, is certainly one of the most widely used alkaloids in the world. It is, together with its main metabolite, cotinine, responsible for tobacco-dependence. The use of tobacco is closely associated with lung disease, morphological leukocyte modification and generation of oxidant species. The aim of this study was to look for a possible relationship between cotinine, oxidant species generation and oxidative processes. After studying the action of cotinine in some chemical oxidation models and on the enzymatic kinetics of peroxidases (myeloperoxidase and horseradish peroxidase), we concluded that cotinine does not act directly upon H2O2, HOCl, taurine chloramines, horseradish peroxidase or myeloperoxidase.

Perfluorattuja yhdisteitä sisältävien jätevesien puhdistus- ja analyysimenetelmät

Perfluoratut alkyyliyhdisteet eli PFAS-yhdisteet ovat synteettisiä orgaanisia yhdisteitä, joissa on fluorattu hiiliketju. Hiilen ja fluorin väliset vahvat sidokset ovat muodostuneet ongelmaksi jätevedenpuhdistamoilla, sillä yhdisteet eivät hajoa puhdistamoilla käytössä olevilla vedenpuhdistusmenetelmillä. Yhdisteitä kertyy luontoon jätevesien mukana. Kandidaatintyössä on vertailtu yhdisteitä sisältävien vesien käsittelymenetelmiä parhaiten soveltuvan menetelmän löytämiseksi. Menetelmien kustannuksia tai soveltuvuutta vedenpuhdistamomittakaavan prosessiksi ei ole arvioitu. Lisäksi työssä on koottu yhdisteitä sisältävien jätevesien analysointiin sopivia analyysimenetelmiä. Soveltuvat puhdistus- ja analyysimenetelmät on esitelty uusien tieteellisten artikkelien pohjalta. Mahdollisia erotusmenetelmiä ovat membraanierotus ja sorptio. Membraaneista soveltuvimpia ovat nanosuodatus- ja käänteisosmoosimembraanit, joilla erottuvat jopa 0,0001 μm:n kokoiset partikkelit. PFAS-yhdisteet voidaan erottaa sorptiolla muun muassa aktiivihiileen. Yhdisteiden rakenne hajoaa nykyaikaisilla hapetusmenetelmillä ja polttamalla lietteen mukana. Hapettaminen permanganaatin avulla ei tuottanut hyvää tulosta, mutta fotokemiallisella hapetuksella ja alhaisen lämpötilan plasmatekniikalla (NTP) yhdisteiden rakenne hajosi lähes kokonaan. Fotokemiallinen hapetus onnistui erityisesti perfluorokarboksyylihapoilla, joiden rakenne hajosi jopa kolmessa tunnissa. Yleisimmin käytetty analyysimenetelmä on nestekromatografin ja massaspektrometrin yhdistelmä (LC-MS/MS) ja matriisivaikutus minimoidaan tyypillisesti kiinteäfaasiuutolla (SPE). Työssä esitellyistä käsittelymenetelmistä parhaiten soveltuva on NTP-menetelmä, koska sillä saatiin tutkimusten mukaan hajotettua yhdisteiden rakenne muita menetelmiä lyhyemmässä ajassa ja se soveltuu parhaiten kaikille PFAS-yhdisteille. NTP-menetelmässä ei tarvita katalyyttiä tai lisäkemikaaleja. Voimakkaana hapettimena toimivat epästabiilit hydroksyyliradikaalit, jotka syntyvät koronapurkauksen kautta. Koronapurkauksessa muodostuu myös otsonia ja lisäksi vapaa happi voi tehostaa hapettumista. Menetelmässä muodostuvien hajoamistuotteiden hallinta vaatii lisätutkimusta. Mahdollinen hallintakeino voisi olla esimerkiksi hapettumisessa vapautuvien fluoridi-ionien saostaminen. Muodostuvien hajoamistuotteiden toksisuutta voitaisiin tarkkailla biosensorilla.

Tetrathiafulvalene and 2,2'-Bipyridine: Bridging both Worlds in the Pursuit of Novel Molecular Materials

The preparation and characterization of two families of building blocks for molecule-based magnetic and conducting materials are described in three projects. In the first project the synthesis and characterization of three bis-imine ligands LI - L3 is reported. Coordination of LI to a series of metal salts afforded the five novel coordination complexes Sn(L4)C4 (I), [Mn(L4)(u-CI)(CI)(EtOH)h (II), [CU(L4)(u-sal) h(CI04)2 (sal = salicylaldehyde anion) (III), [Fe(Ls)2]CI (IV) and [Fe(LI)h(u-O) (V). All complexes have been structurally and magnetically characterized. X-ray diffraction studies revealed that, upon coordination to Lewis acidic metal salts, the imine bonds of LI are susceptible to nucleophilic attack. As a consequence, the coordination complexes (I) - (IV) contain either the cyclised ligand L4 or hydrolysed ligand Ls. In contrast, the dimeric Fe3+ complex (V) comprises two intact ligand LI molecules. In. this complex, the ligand chelates two Fe(III) centres in a bis-bidentate manner through the lone pairs of a phenoxy oxygen and an imine nitrogen atom. Magnetic studies of complexes (II-V) indicate that the dominant interactions between neighbouring metal centres in all of the complexes are antiferromagnetic. In the second project the synthesis and characterization two families of TTF donors, namely the cyano aryl compounds (VI) - (XI) and the his-aryl TTF derivatives (XII) - (XIV) are reported. The crystal structures of compounds (VI), (VII), (IX) and (XII) exhibit regular stacks comprising of neutral donors. The UV -Vis spectra of compounds (VI) - (XIV) present an leT band, indicative of the transfer of electron density from the TTF donors to the aryl acceptor molecules. Chemical oxidation of donors (VI), (VII), (IX) and (XII) with iodine afforded a series of CT salts that where possible have been characterized by single crystal X -ray diffraction. Structural studies showed that the radical cations in these salts are organized in stacks comprising of dimers of oxidized TTF donors. All four salts behave as semiconductors, displaying room temperature conductivities ranging from 1.852 x 10-7 to 9.620 X 10-3 Scm-I. A second series of CT salts were successfully prepared via the technique of electrocrystallization. Following this methodology, single crystals of two CT salts were obtained. The single crystal X-ray structures of both salts are isostructural, displaying stacks formed by trimers of oxidized donors. Variable temperature conductivity measurements carried out on this series of CT salts reveal they also are semiconductors with conductivities ranging from 2.94 x 10-7 to 1.960 X 10-3 S em-I at room temperature. In the third project the synthesis and characterization of a series of MII(hfac)2 coordination complexes of donor ligand (XII) where M2+ = Co2+, Cu2+, Ni2+ and Zn2+ are reported. These complexes crystallize in a head-to-tail arrangement of TTF donor and bipyridine moieties, placing the metal centres and hfac ligands are located outside the stacks. Magnetic studies of the complexes (XV) - (XVIII) indicate that the bulky hfac ligands prevent neighbouring metal centres from assembling in close proximity, and thus they are magnetically isolated.

Triarylamminium radical-cation complexes: design and magnetic properties and Base-catalyzed hydrosilylation: mechanism and substrate scope

1. Triarylamminium radical-cation complexes. The detailed study of manganese, copper and nickel metal-radical complexes with triarylamminium ligands was conducted. Stable, neutral and pseudo-octahedral coordination monometallic complexes with simple monodentate 2,2`-bipyridine ligand containing a redox-active N,N`-(4,4`-dimethoxydiphenyl-amino) substituent were synthesized and fully characterized. The one-electron oxidation process and formation of persistent radical-cation complexes was observed by cyclic voltammetry and spectroelectrochemical measurements. Evans method measurements were performed with radical-cation complexes generated by chemical one-electron oxidation with NOPF6 in acetonitrile. The experimental results indicate ferromagnetic coupling between metal and triarylamminium cation in manganese (II) complex and antiferromagnetic coupling in nickel (II) complex. This data is supported by DFT calculations which also lend weight to the  spin polarization mechanism as an operative model for magnetic exchange coupling. Neutral bimetallic complexes with a new ditopic ligand were synthesized and fully characterized, including magnetic and electrochemical studies. Chemical oxidation of these precursor complexes did not generate radical-cations, but dicationic complexes, which was confirmed by UV-vis and EPR-experiments, as well as varied temperature magnetic measurements. DFT calculations for radical-cation complexes are included. A synthetic pathway for polytopic ligand with multiple redox-active triarylamine sites was developed. The structure of the ligand is presumably suitable for -spin polarization exchange model and allows for production of polymetallic complexes having high spin ground states. 2. Base-catalyzed hydrosilylation. A simple reductive base-catalyzed hydrosilation of aldehydes and ketones was adapted to the use of the cheap, safe, and non-toxic polymethylhydrosiloxane (PMHS) instead of the common PhSiH3 and (EtO)3SiH, which present significant cost and safety concerns, respectively. The conversion of silane into pentacoordinate silicate species upon addition of a base was studied in details for the cases of phenyl silane and PMHS and is believed to be essential for the hydrosilylation process. We discovered that nucleophiles (a base or fluoride-anion) induced the rearrangement of PMHS and TMDS into light silanes: MeSiH3 and Me2SiH2, respectively. The reductive properties of PMHS under basic conditions can be attributed to the formation of methyl silane and its conversion into a silicate species. A procedure for the generation of methyl silane and its use in further efficient reductions of aldehydes and ketones has been developed. The protocol was extended to the selective reduction of esters and tertiary amides into alcohols and aldimines into amines with good isolated yields and reduction of heterocyclic compounds was attempted.

POCN-type Pincer Complexes of NiII and NiIII : synthesis, reactivities, catalytic activities and physical properties

Cette thèse décrit la synthèse, la caractérisation, les réactivités, et les propriétés physiques de complexes divalents et trivalents de Ni formés à partir de nouveaux ligands «pincer» de type POCN. Les ligands POCN de type amine sont préparés d’une façon simple et efficace via l’amination réductrice de 3-hydroxybenzaldéhyde avec NaBH4 et plusieurs amines, suivie par la phosphination de l’amino alcool résultant pour installer la fonction phosphinite (OPR2); le ligand POCN de type imine 1,3-(i-Pr)2PC6H4C(H)=N(CH2Ph) est préparé de façon similaire en faisant usage de PhCH2NH2 en l’absence de NaBH4. La réaction de ces ligands «pincer» de type POCN avec NiBr2(CH3CN)x en présence d’une base résulte en un bon rendement de la cyclométalation du lien C-H situé en ortho aux fonctions amine et phosphinite. Il fut découvert que la base est essentielle pour la propreté et le haut rendement de la formation des complexes «pincer» désirés. Nous avons préparé des complexes «pincer» plan- carrés de type POCN, (POCNRR΄)NiBr, possédant des fonctions amines secondaires et tertiaires qui démontrent des réactivités différentes selon les substituants R et R΄. Par exemple, les complexes possédant des fonctions amines tertiaires ArCH2NR2 (NR2= NMe2, NEt2, and morpholinyl) démontrent des propriétés rédox intéressantes et pourraient être convertis en leurs analogues trivalents (POCNR2)NiBr2 lorsque réagis avec Br2 ou N-bromosuccinimide (NBS). Les complexes trivalents paramagnétiques à 17 électrons adoptent une géométrie de type plan-carré déformée, les atomes de Br occupant les positions axiale et équatoriale. Les analyses «DSC» et «TGA» des ces composés ont démontré qu’ils sont thermiquement stables jusqu’à ~170 °C; tandis que la spectroscopie d’absorption en solution a démontré qu’ils se décomposent thermiquement à beaucoup plus basse température pour regénérer les complexes divalents ne possédant qu’un seul Br; l’encombrement stérique des substitutants amines accélère cette route de décomposition de façon significative. Les analogues NMe2 et N(morpholinyl) de ces espèces de NiIII sont actifs pour catalyser la réaction d’addition de Kharasch, de CX4 à des oléfines telles que le styrène, tandis qu’il fut découvert que l’analogue le moins thermiquement stable (POCNEt2)Ni est complètement inerte pour catalyser cette réaction. Les complexes (POCNRH)NiBr possédant des fonctions amines secondaires permettent l’accès à des fonctions amines substituées de façon non symétrique via leur réaction avec des halogénures d’alkyle. Un autre avantage important de ces complexes réside dans la possibilité de déprotonation pour préparer des complexes POCN de type amide. De telles tentatives pour déprotoner les fonctions NRH nous ont permis de préparer des espèces dimériques possédant des ligands amides pontants. La nature dimérique des ces complexes [P,C,N,N-(2,6-(i-Pr)2PC6H3CH2NR)Ni]2 (R= PhCH2 et Ph) fut établie par des études de diffraction des rayons-X qui ont démontré différentes géométries pour les cœurs Ni2N2 selon le substituant N : l’analogue (PhCH2)N possède une orientation syn des substitutants benzyles et un arrangement ressemblant à celui du cyclobutane du Ni et des atomes d’azote, tandis que l’analogue PhN adopte un arrangement de type diamant quasi-planaire des atomes du Ni et des atomes d’azote et une orientation anti des substituants phényles. Les espèces dimériques ne se dissocient pas en présence d’alcools, mais elles promouvoient l’alcoolyse catalytique de l’acrylonitrile. De façon intéressante, les rendements de ces réactions sont plus élevés avec les alcools possédant des fonctions O-H plus acides, avec un nombre de «turnover» catalytique pouvant atteindre 2000 dans le cas de m-cresol. Nous croyons que ces réactions d’alcoolyse procèdent par activation hétérolytique de l’alcool par l’espèce dimérique via des liaisons hydrogènes avec une ou deux des fonctions amides du dimère. Les espèces dimériques de Ni (II) s’oxydent facilement électrochimiquement et par reaction avec NBS ou Br2. De façon surprenante, l’oxydation chimique mène à l’isolation de nouveaux produits monomériques dans lesquels le centre métallique et le ligand sont oxydés. Le mécanisme d’oxydation fut aussi investigué par RMN, «UV-vis-NIR», «DFT» et spectroélectrochimie.

Effect of mechanical milling on the structural, magnetic and dielectric properties of coprecipitated ultrafine zinc ferrite

Nanosized ZnFe2O4 particles containing traces of a-Fe2O3 by intent were produced by low temperature chemical coprecipitation methods. These particles were subjected to high-energy ball milling. These were then characterised using X-ray diffraction, magnetisation and dielectric studies. The effect of milling on zinc ferrite particles have been studied with a view to ascertaining the anomalous behaviour of these materials in the nanoregime. X-ray diffraction and magnetisation studies carried out show that these particles are associated with strains and it is the surface effects that contribute to the magnetisation. Hematite percentage, probably due to decomposition of zinc ferrite, increases with milling. Dielectric behaviour of these particles is due to interfacial polarisation as proposed by Koops. Also the defects caused by the milling produce traps in the surface layer contributes to dielectric permittivity via spin polarised electron tunnelling between grains. The ionic mechanism is enhanced in dielectrics with the rise in temperature which results in the increase of dielectric permittivity with temperature.

Koordinationschemie auf Oberflächen

Oberflächen, die reversibel auf einen externen Stimulus reagieren, werden als intelligente Oberflächen bezeichnet und sind von großem Interesse für Wissenschaft und Technik. Im diesem Rahmen haben wir ein modulares Synthesekonzept entwickelt, das die spontane Selbstorganisation funktionaler Adsorbatmoleküle auf Au(111) und HOPG ausnutzt. Das Design der Adsorbatmoleküle erlaubt eine modulare Synthese. Scheibchenförmige Moleküle wie Phthalocyanine und Porphyrine, die in der Peripherie Thioetherseitenketten tragen, dienen als Anbindungseinheiten. Das zentrale Metallatom dient als Anknüpfungspunkt für starre Einheiten, die aus Abstandshaltern und Funktionsträgern bestehen. Dieses Konzept erlaubt es sowohl die laterale Separation Funktionseinheiten einzustellen um es den Funktionsträgern zu ermöglichen ohne Behinderung durch Nachbarmoleküle ihre Funktion auszuüben. Für diese Arbeit waren Funktionseinheiten wichtig, deren Funktionen unter anderem Redoxaktivität, Photoschaltbarkeit, Komplexierung katalytisch aktiver Metalle und Immobilisierung onkogener Proteine umfassen. Zum Beleg dieses Konzeptes wurde ein starres Ferrocen-Derivat für die Postmodifizierung eines Zn-Phthalocyanin-SAMs verwendet. Die erhaltenen Filme wurden mittels C1s- und Fe2p-NEXAFS-Spektroskopie ebenso untersucht wie mittels TDS. Strukturell verwandte Komplexe konnten durch RSA charakterisiert werden.