Dielectric behavior of epoxy/BaTiO3 composites using nanostructured ceramic fibers obtained by electrospinning

Composite materials made of epoxy resin and barium titanate (BT) electrospun nanostructured fibers were prepared. BT fibers were synthesized from a sol based on barium acetate, titanium isopropoxide, and poly(vinyl pyrrolidone). The fibers were heat-treated at different temperatures and characterized by X-ray diffraction, scanning electron microscopy (SEM), and Raman spectroscopy. Mats of BT fibers heat-treated at 800 C were embedded in epoxy resin into suitable molds. The composites were characterized by SEM, and dielectric measurements were performed by means of dielectric spectroscopy. The dielectric permittivity and dielectric modulus of epoxy resin/BT-fiber composites were measured for two types of samples: with the electrodes parallel and perpendicular to the BT fiber layers. Interestingly, composite samples with electrodes perpendicular to the fiber layers and a BT content as low as 2 vol % led to dielectric permittivities three times higher than that of pure epoxy resin. © 2013 American Chemical Society.

Photoluminescence of core-shell nanoparticles made from yttrium stabilized zirconia powder grain coated with alumina

A YSZ@Al2O3 nanocomposite was obtained by Al 2O3 coating on the surface of yttrium stabilized zirconia via a polymeric precursor method. The resulting core-shell structures were characterized by X-ray diffraction, scanning electron microscopy, transmission electronic microscopy and PL spectra. The TEM micrographs clearly show a homogeneous Al2O3 shell around the ZrO2 core. The observed PL is related to surface-interface defects. Such novel technologies can, in principle, explore materials which are not available in the bulk single crystal form but their figure-of-merit is dramatically dependent on the surface-interface defect states. © 2013 This journal isThe Royal Society of Chemistry.

Estudo de propriedades anelásticas de MgB2

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Efeito do tamanho dos grânulos nas características estruturais e físico-químicas do amido de trigo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito do oxigênio nas propriedades anelásticas da liga Ti-10Mo para aplicação biomédica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Caracterização mineralógica, química e solubilização do potássio de glauconita modificada

Demand for potassium in Brazil is large and is constantly increasing, but only about 5% of all consumed potassium is produced in the country. This low domestic production implies high rate of potassium imports, leaving the country vulnerable in the event of any difficulty to import this product and currency fluctuations. The modified glauconite is a rock that has a high potential for potassium exploration, found in Minas Gerais state, its extraction is relatively cheap and the prospected rock volume is high. The difficulty for its use as a direct source of potassium is in its low solubility. Thus, the objective of this study was to perform a chemical and mineralogical characterization of the modified glauconite and evaluate the effectiveness of techniques and treatments in the potassium solubilization contained in the rock. For this study, it was used characterization techniques such as X-ray diffraction, scanning electron microscopy, diffraction by Synchrotron Light and chemical analysis of high and low power of potassium extraction. Also granulometric testing and thermal treatments with different forms of calcination were carried out. Overall, it was found that the modified glauconite is a compound of minerals, of the mica groups K-feldspar and quartz and calcination substantially alter the crystal structure of these minerals, increasing the potassium availability. While the natural solubility of glauconite modified be very low, rock calcination added with high fluxes of calcium and low magnesium content at 1200 °C led to potassium solubility increase in order of 100 times compared to that observed in the glauconite natural modified.

Síntese e funcionalização de superfícies de óxido de ferro superparamagnéticos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Reciclagem de resíduo a partir de cinzas de carvão mineral: produção de argamassas

Este trabalho tem como objetivo avaliar a possibilidade de aproveitamento do resíduo obtido a partir da combustão do carvão mineral em caldeiras de leito fluidizado, de uma refinaria de alumina no estado do Pará. Neste contexto, foi avaliada a incorporação de cinzas volantes, como pozolana, em substituição parcial do cimento na produção de argamassas. Para tanto, foram elaborados corpos de prova utilizando-se o cimento do tipo Portland CPII-E-32. As misturas foram definidas na proporção 4:1, ou seja, 4 partes de agregado (sílica) e 1 parte de aglomerante (cimento e cinza), com a inserção de cinza nos teores de 10, 20, 30, 40 e 50 em porcentagem com relação ao cimento, além da argamassa sem adição. Foram definidas duas relações água/aglomerante, 0,4 e 0,8. Após tempo de cura de 7 e 28 dias, foram feitos testes de resistência à compressão para análise de comportamento. Além disso, as argamassas com a relação água/aglomerante 0,8 foram sujeitas a análises complementares de Difração de Raios-X, Microscopia Eletrônica de Varredura, absorção de água, porosidade aparente e massa específica aparente, cujos resultados obtidos mostraram-se compatíveis quando comparados com os dados da literatura, demonstrando ser viável a aplicação das cinzas estudadas na indústria da construção civil.

Desenvolvimento e otimização de materiais nanocristalinos para células solares sensibilizadas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Síntese e caracterização elétrica de filmes varistores à base de 'SN''O IND.2' modificados superficialmente por difusão 'CR POT.3+' na região do contorno de grão

Pós-graduação em Química - IQ

Influence of Oxygen Content and Microstructure on the Mechanical Properties and Biocompatibility of Ti-15 wt%Mo Alloy Used for Biomedical Applications

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Controlled Synthesis of Layered Sn3O4 Nanobelts by Carbothermal Reduction Method and Their Gas Sensor Properties

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Obtenção de rochas sintéticas a partir de resíduos de vidro comercial e pó de granito

Pós-graduação em Engenharia Mecânica - FEG

Laser irradiation and thermal treatment inducing selective crystallization in Sb2O3-Sb2S3 glassy films

The influence of both thermal treatment and laser irradiation on the structural and optical properties of films in the Sb 2 O 3 –Sb 2 S 3 system was investigated. The films were prepared by RF-sputtering using glass compositions as raw materials. Irreversible photodarkening effect was observed after exposure the films to a 458nm solid state laser. It is shown, for the first time, the use of holographic technique to measure “in situ”, simultaneously and independently, the phase and amplitude modulations in glassy films. The films were also photo-crystallized and analysed “in situ” using a laser coupled to a micro-Raman equipment. Results showed that Sb 2 S 3 crystalline phase was obtained after irradiation. The effect of thermal annealing on the structure of the films was carried out. Different from the result obtained by irradiation, thermal annealing induces the crystallization of the Sb 2 O 3 phase. Photo and thermal induced effects on films were studied using UV–Vis and Raman spectroscopy, atomic force microscopy (AFM), thermal analysis (DSC), X-ray diffraction, scanning electron microscopy (MEV) and energy-dispersive X-ray spectroscopy (EDX).

Characterization and application of nanostructured films containing Au and TiO2 nanoparticles supported in bacterial cellulose

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)