Energy Management guide for light industry and commerce /

Bibliography: p. 21-22.

Fixed bed downdraft gasification of paper industry wastes

The two main wastes generated from secondary fibre paper mills are rejects (composed mainly of plastics and fibres) and de-inking sludge, both of which are evolved from the pulping process during paper manufacture. The current practice for the disposal of these wastes is either by land-spreading or land-filling. This work explores the gasification of blends of pre-conditioned rejects and de-inking sludge pellets with mixed wood chips in an Imbert type fixed bed downdraft gasifier with a maximum feeding capacity of 10kg/h. The producer gases evolved would generate combined heat and power (CHP) in an internal combustion engine. The results show that as much as 80wt.% of a brown paper mill's rejects (consisting of 20wt.% mixed plastics and 80wt.% paper fibres) could be successfully gasified in a blend with 20wt.% mixed wood chips. The producer gas composition was 16.24% H, 23.34% CO, 12.71% CO 5.21% CH and 42.49% N (v/v%) with a higher heating value of 7.3MJ/Nm. After the removal of tar and water condensate the producer gas was of sufficient calorific value and flow rate to power a 10kWe gas engine. Some blends using rejects from other mill types were not successful, and the limiting factor was usually the agglomeration of plastics present within the fuel.

The development of a sustainable agricultural industry through the application of biochar and pyroligneous acid

This paper marks the first in a series of studies into the potential use of pyrolysis products in the development of more sustainable practices within the agricultural industry. In this study, the immediate benefits of the application of biochar to crop yields of Raphanus sativus (radishes) are assessed. Furthermore, the study reports on the preliminary findings into the potential application of pyroligneous acid (wood vinegar) as a biocidal agent against crop disease. Although germination tests undertaken on biochar/compost blends of up to 1: 2, by weight, showed no significant adverse effect from the addition of the nutrient rich carbonaceous solid, evidence of substantial increases in crop yield through the addition of biochar were not observed. In sharp contrast, zones of inhibition were observed at 3-10 vol. % upon application of pyroligneous acid to two causal agents responsible for certain diseases in vegetable and fruit crops, i.e. Rhizobium radiobacter (agrobacterium tumefaciens) and Xanthomonas campestris, highlighting the versatility in the application of pyrolysis products and avenues for exploration in the development of this biomass conversion technology.

Hierarchical Forest Management Planning: A Bilevel Wood Supply Modelling Approach

Le processus de planification forestière hiérarchique présentement en place sur les terres publiques risque d’échouer à deux niveaux. Au niveau supérieur, le processus en place ne fournit pas une preuve suffisante de la durabilité du niveau de récolte actuel. À un niveau inférieur, le processus en place n’appuie pas la réalisation du plein potentiel de création de valeur de la ressource forestière, contraignant parfois inutilement la planification à court terme de la récolte. Ces échecs sont attribuables à certaines hypothèses implicites au modèle d’optimisation de la possibilité forestière, ce qui pourrait expliquer pourquoi ce problème n’est pas bien documenté dans la littérature. Nous utilisons la théorie de l’agence pour modéliser le processus de planification forestière hiérarchique sur les terres publiques. Nous développons un cadre de simulation itératif en deux étapes pour estimer l’effet à long terme de l’interaction entre l’État et le consommateur de fibre, nous permettant ainsi d’établir certaines conditions pouvant mener à des ruptures de stock. Nous proposons ensuite une formulation améliorée du modèle d’optimisation de la possibilité forestière. La formulation classique du modèle d’optimisation de la possibilité forestière (c.-à-d., maximisation du rendement soutenu en fibre) ne considère pas que le consommateur de fibre industriel souhaite maximiser son profit, mais suppose plutôt la consommation totale de l’offre de fibre à chaque période, peu importe le potentiel de création de valeur de celle-ci. Nous étendons la formulation classique du modèle d’optimisation de la possibilité forestière afin de permettre l’anticipation du comportement du consommateur de fibre, augmentant ainsi la probabilité que l’offre de fibre soit entièrement consommée, rétablissant ainsi la validité de l’hypothèse de consommation totale de l’offre de fibre implicite au modèle d’optimisation. Nous modélisons la relation principal-agent entre le gouvernement et l’industrie à l’aide d’une formulation biniveau du modèle optimisation, où le niveau supérieur représente le processus de détermination de la possibilité forestière (responsabilité du gouvernement), et le niveau inférieur représente le processus de consommation de la fibre (responsabilité de l’industrie). Nous montrons que la formulation biniveau peux atténuer le risque de ruptures de stock, améliorant ainsi la crédibilité du processus de planification forestière hiérarchique. Ensemble, le modèle biniveau d’optimisation de la possibilité forestière et la méthodologie que nous avons développée pour résoudre celui-ci à l’optimalité, représentent une alternative aux méthodes actuellement utilisées. Notre modèle biniveau et le cadre de simulation itérative représentent un pas vers l’avant en matière de technologie de planification forestière axée sur la création de valeur. L’intégration explicite d’objectifs et de contraintes industrielles au processus de planification forestière, dès la détermination de la possibilité forestière, devrait favoriser une collaboration accrue entre les instances gouvernementales et industrielles, permettant ainsi d’exploiter le plein potentiel de création de valeur de la ressource forestière.

Production of bioplastics from hydrolysates of paper industry by Haloferax mediterranei

The biorefinery concept has attracted much attention over the last decade due to increasing concerns about the use of fossil resources. In this context emerged the use of bioplastics, namely polyhydroxyalkanoates (PHA). PHA are biocompatible and biodegradable plastics that can be obtained from renewable raw materials and can constitute an alternative solution to conventional plastics. In this work, hydrolysed cellulose pulp, coming from Eucalyptus globulus wood cooking, was used as substrate to the PHA-storing bacteria Haloferax mediterranei. The hydrolysed pulp is rich in simple sugars, mainly glucose (81.96 g.L-1) and xylose (20.90 g.L-1). Tests were made in defined medium with glucose and xylose and in hydrolysate supplemented with salts and yeast extract. Different concentrations of glucose were tested, namely 10, 15, 20, 30 and 40 g.L-1. The best accumulation results (27.1 % of PHA) were obtained in hydrolysate medium with 10 g.L-1. Using this concentration, assays were performed in fed-batch and sequencing batch reactor conditions in order to determine the best feeding strategy. The strategy that led to the best results was fed-batch assay with 24.7 % of PHA. An assay without sterile conditions was performed, in which was obtained the same growth than in sterilization test. Finally it was performed an assay in a bioreactor and a fast growth (0.14 h-1) with high glucose and xylose consumption rates (0.368 g.L-1.h-1 and 0.0947 g.L-1.h-1, respectively) were obtained. However 1.50 g.L-1 of PHA, corresponding to 16.1 % (92.52 % of 3HB and 3HV of 7.48 %) of % PHA were observed. The polymer was further characterized by DSC with a glass transition temperature of -6.07 °C, a melting temperature of 156.3 °C and a melting enthalpy of 63.07 J.g-1, values that are in accordance with the literature. This work recognizes for the first time the suitability of the pulp paper hydrolysate as a substrate for PHA production by H. mediterranei.

Industry wage survey.

Mode of access: Internet.

Participation of portuguese manufacturing industry in global value chains

Portugal’s manufacturing sector has a significant importance both in national income and employment. As has been pointed out by several researchers, the traditional methods of analysis fail to grasp all the dimensions of economic competitiveness. This dissertation is then, at its core, an analysis of Portugal’s manufacturing industry in terms of the latter’s value added to production and impact to employment under the framework of global value chains. The current dissertation seeks to study in which way the Portuguese manufacturing industry, and its respective sectors, has a direct and indirect impact on the creation of value added and employment and how this impact can be measured. For development of this work the input-output approach for calculation of multipliers and the new framework proposed by Timmer et al. (2013) for calculation of GVC income and GVC jobs indicators were used, elaborated on the basis of the WIOD project dataset. Moreover, to illustrate the application of the provided methodology the Portuguese textile industry was used as an example. It was found that the changes in final demand of such sectors as Pulp, Paper, Printing and Publishing; Machinery, Nec and Textiles and Textile Products would have a larger impact on generated value added than other manufacturing sectors. At the same time, employment created by the changes in final demand would be more impacted by such sectors as Food, Beverages and Tobacco; Wood and Products of Wood and Cork and Textiles and Textile Products. In this regard, the number of low-skilled workers in Portugal seems to be more effected by changes in final demand, than those occupied by higher -skilled individuals. Moreover, it was found that the distribution of GVC income and GVC jobs for the Portuguese manufacturing industry shares a similar outlook. However, upon closer inspection of GVC labour distribution by skill levels there seems to exist a general progression in which low-skilled jobs requirements are met by local resources, while the need for higher skilled jobs require a greater “off-shoring” of work The results obtained through calculations of presented multipliers provide a powerful tool for policy makers in strategic planning of development of national economy. Using the provided methodology and obtained results, a government and supranational organizations could define which industry would have the greatest impact for an additional unit of output generated through the economy, and thus define the sectors for further investments.

Adsorption of pesticides onto activated carbons from wood composites

A series of activated carbon was produced from particleboard and medium-density fibreboard monoliths, which are waste originated from the industry, and then characterized and evaluated for potential application for phenoxyacetic acids removals, such 2,4-dichlorophenoxyacetic acid (2,4-D), 2-methyl-4-chlorophenoxy acetic acid (MCPA) and 3-(3,4-dichlorophenyl)-1,1-dimethylurea (diuron), from the liquid phase. All AC retain the shape of the precursor, and displays a microporous structure well-developed, reaching 0.58 cm 3 g -1. The adsorption isotherms for three pesticides were obtained in the optimal conditions and the AC with high superficial area and micropore volume exhibited better performance, allowing to state that, this AC could be a great substitute of those habitually used for this purpose. The pesticides adsorption data were linearized using the Langmuir and Freundlich equation, being the first a very good fit to the experimental data.

Adsorption of pesticides onto activated carbons from wood composites

A series of activated carbon was produced from particleboard and medium-density fibreboard monoliths, which are waste originated from the industry, and then characterized and evaluated for potential application for phenoxyacetic acids removals, such 2,4-dichlorophenoxyacetic acid (2,4-D), 2-methyl-4-chlorophenoxy acetic acid (MCPA) and 3-(3,4-dichlorophenyl)-1,1-dimethylurea (diuron), from the liquid phase. All AC retain the shape of the precursor, and displays a microporous structure well-developed, reaching 0.58 cm 3 g -1. The adsorption isotherms for three pesticides were obtained in the optimal conditions and the AC with high superficial area and micropore volume exhibited better performance, allowing to state that, this AC could be a great substitute of those habitually used for this purpose. The pesticides adsorption data were linearized using the Langmuir and Freundlich equation, being the first a very good fit to the experimental data.