Effect of chute level on mill capacity

IN MANY FACTORIES, the feed chute of the first mill is operated with a high chute level for the purpose of maximising the cane rate through the mill. There is a trend towards trying to control chute level within a small control range near the top of a chute that can result in rapid changes in cane feeding rate to maintain the chute level set point. This paper reviews the theory that predicts higher cane rate with higher chute level and discusses the main weakness in the theory that it does not consider the beneficial effect on capacity of cane falling from the top of the chute to the top surface of the cane mat. An extension to the chute theory model is described that predicts higher capacity with lower chute level because of the effect of the falling cane. The original model and this extended model are believed to be the upper and lower limits to the true effect. The paper reports an experiment that measured the real effect of chute level on capacity and finds that increasing chute level does lead to higher capacity but that the trend is only about one-third as strong as the original theory predicted. The paper questions whether the benefits of slightly greater capacity outweigh the costs of operating with the small control range near the top of the chute.

An alternative approach to setting a mill

The conventional approach to setting a milling unit is essentially based on the desire to achieve a particular bagasse moisture content or fibre fill in each nip of the mill. This approach relies on the selection of the speed at which the mill will operate for the selected fibre rate. There is rarely any checking that the selected speed or the selected fibre fill is achieved and the same set of assumptions is generally carried over to use again in the next year. The conventional approach largely ignores the fact that the selection of mill settings actually determines the speed at which the mill will operate. Making an adjustment with the intent of changing the performance of the mill often also changes the speed of the mill as an unintended consequence. This paper presents an alternative approach to mill setting. The approach discussed makes use of mill feeding theory to define the relationship between fibre rate, mill speed and mill settings and uses that theory to provide an alternative means of determining the settings in some nips of the mill. Mill feeding theory shows that, as the feed work opening reduces, roll speed increases. The theory also shows that there is an optimal underfeed opening and Donnelly chute exit opening that will minimise roll speed and that the current South African guidelines appear to be well away from those optimal values.

‘Ngulluck Katitj Wah Koorl Koorliny/ Us mob going along learning to research together’ : drawing on action research to develop a literature review on Indigenous gendered health and wellbeing

This paper describes the collaborative work practices of the Health and Wellbeing Node within the National Indigenous Research and Knowledges Network (NIRAKN). The authors reflect on the processes they used to research and develop a literature review. As a newly established research team, the Health and Wellbeing Node members developed a collaborative approach that was informed by Action Research practices and underpinned by Indigenous ways of working. The authors identify strong links between Action Research and Indigenous processes. They suggest that, through ongoing cycles of research and review, the NIRAKN Health and Wellbeing Node developed a culturally safe, respectful and trulycollaborative way of working together and forming the identity of their work group. In this paper, they describe their developing work processes and explain the way that pictorial conceptual models contributed to their emerging ideas.

Contracted site: Artist on paper, drawing

Traditionally the notion of drawing in-situ has suggested the physical presence of the artist in the environment under scrutiny. The assumption here of enhanced connectivity, however, is hasty in light of the idea that situation implies a relative spatial value determined by the interplay of subject and location, where the possibility of not being “in-situ” is problematic. The fact that traditional drawing in-situ, such as the rendering of landscape, requires a framing of the world “out there” suggests a distance between the perceived object of representation and the drawing surface. Rather than suggesting that some drawing is situated and other sorts of drawing are not, however, I argue that situation or site is variously extended and intensified depending on the nature of mediation between surface and environment. The suggestion here is that site is not so much a precondition as a performative function, developed in the act of drawing and always implicating the drawing surface. In my discussion I focus on specific works by Toba Khedoori and Cameron Robbins. As well, in using my own recent drawing practice as a case study, I argue that the geography of site is delimited neither by horizon nor the boundaries of the paper. Rather, I propose that site and drawing surface coincide in variously intensive and extensive ways.

MATLAB/Simulink simulation and C2000 code generation model for a grid-interactive 3-phase 4-wire inverter

This work is a MATLAB/Simulink model of a controller for a three-phase, four-wire, grid-interactive inverter. The model provides capacity for simulating the performance of power electroinic hardware, as well as code generation for an embedded controller. The implemented hardware topology is a three-leg bridge with a neutral connection to the centre-tap of the DC bus. An LQR-based current controller and MAF-based phase detector are implemented. The model is configured for code generation for a Texas Instruments TMS320F28335 Digital Signal Processor (DSP).

Trialling a technopulp belt press filter at Pioneer Mill

Wilmar’s Pioneer Sugar mill has a need to replace some small rotary vacuum filters (RVFs) due to the condition of existing aged plant. A vacuum belt press filter (VBPF) manufactured by Technopulp of Brazil was purchased and installed at Pioneer Mill in September/October 2012 and commissioning trials undertaken over a five week period commencing in early November. There are no vacuum belt press filters currently in use in Australian sugar mills for mud processing. The Technopulp filter is a relatively common and well accepted technology with over 600 units installed. The main attractions for the VBPF to Pioneer Mill were…

Seasonal effects of foliar application of phosphonate on phosphonate translocation, in vitro pollen viability and pollen germination in `Hass' avocado (Persea americana Mill.)

Phosphonate fungicides are used widely in the control of diseases caused by Phytophthora cinnamomi Rands. For the most part phosphonate is seen as a safe to use on crops with phytotoxicity rare. However, recent research has shown that phosphonate has detrimental effects on the floral biology of some indigenous Australian plants. Since phosphonate fungicides are regularly used for the control of Phytophthora root rot in avocados, research was carried out to study the translocation of phosphonate fungicide in 'Hass' trees and any effects on their floral biology. Field-grown trees were sprayed with 0, 0.06 or 0.12 M mono-dipotassium phosphonate (pH 7.2) at summer flush maturity, floral bud break or anthesis. Following treatment, phosphonic acid concentrations were determined in leaves, roots, inflorescence rachi and flowers and in vitro pollen germination and pollen tube growth studied. Phosphonic acid concentration in the roots and floral parts was related to their sink strength at the respective times of application with concentration in roots highest (36.9.mg g±1) after treatment at summer flush maturity and in flowers (234.7 mg g±1) after treatment during early anthesis. Phosphonate at >0.03 M was found to be significantly phytotoxic to in vitro pollen germination and pollen tube growth. However, this rate gave a concentration far in excess of that measured in plant tissues following standard commercial applications of mono-dipotassium phosphonate fungicide. There was a small effect on pollen germination and pollen tube growth when 0.06 and 0.12 M mono-dipotassium phosphonate was applied during early anthesis. However, under favourable pollination and fruit set conditions it is not expected to have commercial impact on tree yield. However, there may be detrimental commercial implications from phosphonate sprays at early anthesis if unfavourable climatic conditions for pollination and fruit set subsequently occur. A commercial implication from this study is that phosphonic acid root concentrations can be elevated and maintained with strategic foliar applications of phosphonate fungicide timed to coincide with peaks in root sink strength. These occur at the end of the spring and summer flushes when shoot growth is relatively quiescent. Additional foliar applications may be advantageous in under high disease-pressure situations but where possible should be timed to minimize overlap with other significant growth events in the tree such as rapid inflorescence, and fruit development and major vegetative flushing.

Constitutive modeling of shape memory alloy wire with non-local rate kinetics

A constitutive modeling approach for shape memory alloy (SMA) wire by taking into account the microstructural phase inhomogeneity and the associated solid-solid phase transformation kinetics is reported in this paper. The approach is applicable to general thermomechanical loading. Characterization of various scales in the non-local rate sensitive kinetics is the main focus of this paper. Design of SMA materials and actuators not only involve an optimal exploitation of the hysteresis loops during loading-unloading, but also accounts for fatigue and training cycle identifications. For a successful design of SMA integrated actuator systems, it is essential to include the microstructural inhomogeneity effects and the loading rate dependence of the martensitic evolution, since these factors play predominant role in fatigue. In the proposed formulation, the evolution of new phase is assumed according to Weibull distribution. Fourier transformation and finite difference methods are applied to arrive at the analytical form of two important scaling parameters. The ratio of these scaling parameters is of the order of 10(6) for stress-free temperature-induced transformation and 10(4) for stress-induced transformation. These scaling parameters are used in order to study the effect of microstructural variation on the thermo-mechanical force and interface driving force. It is observed that the interface driving force is significant during the evolution. Increase in the slopes of the transformation start and end regions in the stress-strain hysteresis loop is observed for mechanical loading with higher rates.

Näppärien mummojen muistelukirjonta - yhteisöllistä ja voimauttavaa käsityöilmaisua

The aim of the study was to get acquainted with the activity of Näppärät Mummot, a Lahti-based crafts society, and its importance to the wellness of the members of the group. The selected aim, i.e., analyzing the wellness, largely affected the whole research process and its results. According to earlier studies in the field, different forms of craft and expressional activity promote one's wellness as well as support the work for one's identity. Based on my theoretical knowledge, my research was set out to: 1) form a general view of crafts culture within Näppärät Mummot and 2) find out how recollective craft that promotes wellness is perceived through communality, experiential activity, work for one's identity, and divided as well as undivided craft. Qualitative field work was governed by ethnographic research strategy, according to which I set out to get thoroughly familiar with the society I was studying. The methods I used to collect data were participant observation and thematic interview. I used a field diary for writing down all data I acquired through the observation. The interviewee group was formed by seven members of Näppärät Mummot. An mp3 recorder was used to record the interviews, which I transcribed later. The method for data analysis was qualitative content analysis, for which I used Weft QDA, a qualitative analysis software application. I formed themes that shed light on research tasks from the data using coding and theory-driven analysis. I kept literature and data I collected in cooperation through the whole analysis process. Lastly, drawing from the classes of meaning of therapeutic craft that I sketched by means of summarizing and classifying, I presented the central concepts that describe the main results of the study. The main results were six concepts that describe Näppärät Mummot's crafts culture and recollective craft with its wellness-beneficial effect: 1) autobiographical craft, 2) shared work for one's identity, 3) shared intention for craft, 4) craft as a partner, 5) individual manner of craft, and 6) shared improvement. Craft promoted wellness in many ways. It was used to promote inner life management in difficult times and it also provided sensations of empowerment through pleasure from craft. Expressional, shared craft also served as means of reinforcing one's identity in various ways. Expressional work for one's identity through autobiographical themes of craft represented rearranging one's life through holistic craft. A personal way of doing things also served as expressional action and work for one's identity even with divided craft. Shared work for identities meant reinforcing the identities of the members through discources of craft and interaction with their close ones. What proves the interconnection between communality and craft as well as their shared meaning is that communality motivated the members to work on their craft projects, while craft served as the means of communication between the members: communication through craft was easier than lingual communication. The results can not be generalized to apply to other groups: they are used to describe the versatile means of recollective craft to promote the well-being among the crafts society Näppärät Mummot. However, the results do introduce a new perspective to the social discussion on how cultural activities promote well-being.

An interactive graphics system for 2-D drawing and design

This paper is about a software system, GRASS-Graphic Software System for 2-D drawing and design—which has been implemented on a PDP-11/35 system with RSX-11M operating system. It is a low cost interactive graphics system for the design of two dimensional drawings and uses a minimum of hardware. It provides comprehensive facilities for creating, editing, storing and retrieving pictures. It has been implemented in the language Pascal and has the potential to be used as a powerful data-imputting tool for a design-automation system. The important features of the system are its low cost, software character generation and a user-trainable character recognizer, which has been included.