Utilization of a Time Domain Simulator in the Technical and Economic Analysis of a Wind Turbine Electric Drive Train

The amount of installed wind power has been growing exponentially during the past ten years. As wind turbines have become a significant source of electrical energy, the interactions between the turbines and the electric power network need to be studied more thoroughly than before. Especially, the behavior of the turbines in fault situations is of prime importance; simply disconnecting all wind turbines from the network during a voltage drop is no longer acceptable, since this would contribute to a total network collapse. These requirements have been a contributor to the increased role of simulations in the study and design of the electric drive train of a wind turbine. When planning a wind power investment, the selection of the site and the turbine are crucial for the economic feasibility of the installation. Economic feasibility, on the other hand, is the factor that determines whether or not investment in wind power will continue, contributing to green electricity production and reduction of emissions. In the selection of the installation site and the turbine (siting and site matching), the properties of the electric drive train of the planned turbine have so far been generally not been taken into account. Additionally, although the loss minimization of some of the individual components of the drive train has been studied, the drive train as a whole has received less attention. Furthermore, as a wind turbine will typically operate at a power level lower than the nominal most of the time, efficiency analysis in the nominal operating point is not sufficient. This doctoral dissertation attempts to combine the two aforementioned areas of interest by studying the applicability of time domain simulations in the analysis of the economicfeasibility of a wind turbine. The utilization of a general-purpose time domain simulator, otherwise applied to the study of network interactions and control systems, in the economic analysis of the wind energy conversion system is studied. The main benefits of the simulation-based method over traditional methods based on analytic calculation of losses include the ability to reuse and recombine existing models, the ability to analyze interactions between the components and subsystems in the electric drive train (something which is impossible when considering different subsystems as independent blocks, as is commonly done in theanalytical calculation of efficiencies), the ability to analyze in a rather straightforward manner the effect of selections other than physical components, for example control algorithms, and the ability to verify assumptions of the effects of a particular design change on the efficiency of the whole system. Based on the work, it can be concluded that differences between two configurations can be seen in the economic performance with only minor modifications to the simulation models used in the network interaction and control method study. This eliminates the need ofdeveloping analytic expressions for losses and enables the study of the system as a whole instead of modeling it as series connection of independent blocks with no lossinterdependencies. Three example cases (site matching, component selection, control principle selection) are provided to illustrate the usage of the approach and analyze its performance.

Wind turbine operation in cold climate

The goal of the master‘s thesis is to determine and estimate ice accretion influence on the wind turbine blade performance. The thesis describes the technique of ice accretion calculation on the wind turbine blade and determination characteristics of the turbine with ice accreted. The methodology of the classic Blade Element Moment Theory was used. Iced blade experimental data was investigated in order to calculate blade with ice characteristics. The obtained results shows that iced blade power coefficient is lower than clean blade one. The heating system implementation shows that in the particular site in the Lapland region it is efficient.

Experimental analysis of the flow between stay and guide vanes of a pump-turbine in pumping mode

An experimental study was conducted in a pump-turbine model in pumping mode, in order to characterize the flow field structure in the region between stay and guide vanes, using mainly the laser-Doppler anemometry in a two-color and back-scattered light-based system. The structure of the steady and unsteady flow was analyzed. The measurements were performed at three operation points. The obtained data provide appropriate boundary conditions and a good base of validation for numerical codes, and for the understanding of main loss mechanisms of this complex flow.

Methodology for wind turbine blade geometry optimization

Nowadays, the upwind three bladed horizontal axis wind turbine is the leading player on the market. It has been found to be the best industrial compromise in the range of different turbine constructions. The current wind industry innovation is conducted in the development of individual turbine components. The blade constitutes 20-25% of the overall turbine budget. Its optimal operation in particular local economic and wind conditions is worth investigating. The blade geometry, namely the chord, twist and airfoil type distributions along the span, responds to the output measures of the blade performance. Therefore, the optimal wind blade geometry can improve the overall turbine performance. The objectives of the dissertation are focused on the development of a methodology and specific tool for the investigation of possible existing wind blade geometry adjustments. The novelty of the methodology presented in the thesis is the multiobjective perspective on wind blade geometry optimization, particularly taking simultaneously into account the local wind conditions and the issue of aerodynamic noise emissions. The presented optimization objective approach has not been investigated previously for the implementation in wind blade design. The possibilities to use different theories for the analysis and search procedures are investigated and sufficient arguments derived for the usage of proposed theories. The tool is used for the test optimization of a particular wind turbine blade. The sensitivity analysis shows the dependence of the outputs on the provided inputs, as well as its relative and absolute divergences and instabilities. The pros and cons of the proposed technique are seen from the practical implementation, which is documented in the results, analysis and conclusion sections.

Wind Turbine Direct-Drive Permanent-Magnet Generator with Direct Liquid Cooling for Mass Reduction

Today’s electrical machine technology allows increasing the wind turbine output power by an order of magnitude from the technology that existed only ten years ago. However, it is sometimes argued that high-power direct-drive wind turbine generators will prove to be of limited practical importance because of their relatively large size and weight. The limited space for the generator in a wind turbine application together with the growing use of wind energy pose a challenge for the design engineers who are trying to increase torque without making the generator larger. When it comes to high torque density, the limiting factor in every electrical machine is heat, and if the electrical machine parts exceed their maximum allowable continuous operating temperature, even for a short time, they can suffer permanent damage. Therefore, highly efficient thermal design or cooling methods is needed. One of the promising solutions to enhance heat transfer performances of high-power, low-speed electrical machines is the direct cooling of the windings. This doctoral dissertation proposes a rotor-surface-magnet synchronous generator with a fractional slot nonoverlapping stator winding made of hollow conductors, through which liquid coolant can be passed directly during the application of current in order to increase the convective heat transfer capabilities and reduce the generator mass. This doctoral dissertation focuses on the electromagnetic design of a liquid-cooled direct-drive permanent-magnet synchronous generator (LC DD-PMSG) for a directdrive wind turbine application. The analytical calculation of the magnetic field distribution is carried out with the ambition of fast and accurate predicting of the main dimensions of the machine and especially the thickness of the permanent magnets; the generator electromagnetic parameters as well as the design optimization. The focus is on the generator design with a fractional slot non-overlapping winding placed into open stator slots. This is an a priori selection to guarantee easy manufacturing of the LC winding. A thermal analysis of the LC DD-PMSG based on a lumped parameter thermal model takes place with the ambition of evaluating the generator thermal performance. The thermal model was adapted to take into account the uneven copper loss distribution resulting from the skin effect as well as the effect of temperature on the copper winding resistance and the thermophysical properties of the coolant. The developed lumpedparameter thermal model and the analytical calculation of the magnetic field distribution can both be integrated with the presented algorithm to optimize an LC DD-PMSG design. Based on an instrumented small prototype with liquid-cooled tooth-coils, the following targets have been achieved: experimental determination of the performance of the direct liquid cooling of the stator winding and validating the temperatures predicted by an analytical thermal model; proving the feasibility of manufacturing the liquid-cooled tooth-coil winding; moreover, demonstration of the objectives of the project to potential customers.

Kaatopaikkakaasujen käsittelyn kehittäminen Korvenmäen kaatopaikalla

Työssä tutkittiin Salossa sijaitsevan Korvenmäen kaatopaikan kaasunkeräysjärjestelmää. Tavoitteena oli selvittää kaatopaikkakaasun talteenoton merkittävimmät haasteet, löytää ratkaisuja ongelmiin ja hajuhaittojen vähentämiseen sekä arvioida keräysjärjestelmän parannusten ja kaatopaikalle tulevan pintarakenteen vaikutus talteenottoon ja hajuhaittoihin. Korvenmäen kaatopaikalla on käytössä vaakakeräysjärjestelmä, jonka merkittävimpiä ongelmia ovat olleet kaatopaikkakaasun matala talteenottoaste, happipitoisuuden nousu, järjestelmän hankala säädettävyys sekä kaatopaikalla ja ympäristössä havaitut hajuhaitat. Muodostuvan ja karkaavan kaatopaikkakaasun määrää arvioitiin Jouko Petäjän metaanilaskentamallin avulla. Tulosten perusteella kaasua muodostuu runsaasti, mutta suurin osa siitä pääsee karkaamaan ympäristöön, sillä arvioitu kaatopaikkakaasun talteenottoaste on tällä hetkellä vain 11 %. Kaasujen käsittelykäytäntöjä suomalaisilla kaatopaikoilla selvitettiin kyselytutkimuksella. Tutkimuksen mukaan kaasunkeräyksen ongelmat ja hajuhaitat ovat yleisiä, mutta erilaisilla toimenpiteillä niitä voidaan huomattavasti vähentää. Korvenmäelle suositeltavia kehitystoimia ovat kaasulinjoihin yhdistettyjen suotoveden keräys- ja tarkkailukaivojen tiivistäminen, vanhojen vaakalinjojen kunnon tarkistus ja korjaus sekä pystykaivojen asentaminen kaasunkeräyksen tehostamiseksi. Pintarakenne tulee valmistuttuaan vähentämään karkaavan kaasun ja kaasulinjoihin imeytyvän ilman määrää. Hajuhaittojen hallinnassa tärkeintä on toimiva kaasunkeräys, mutta lisäksi suositellaan rikkivetyä hapettavien päivittäispeittomateriaalien levittämistä kaatopaikan pinnalle. Kehitystoimenpiteiden myötä kaatopaikkakaasun talteenottoaste tulee paranemaan ja hajuhaitat vähenevät. Kerättävän kaasumäärän kasvaessa mikroturbiinilaitoksen kapasiteettia voidaan lisätä, jotta kaasu saadaan mahdollisimman tehokkaasti hyödynnettyä energiana.

A priori estimation of accuracy and of the number of wells to be employed in limiting dilution assays

The use of limiting dilution assay (LDA) for assessing the frequency of responders in a cell population is a method extensively used by immunologists. A series of studies addressing the statistical method of choice in an LDA have been published. However, none of these studies has addressed the point of how many wells should be employed in a given assay. The objective of this study was to demonstrate how a researcher can predict the number of wells that should be employed in order to obtain results with a given accuracy, and, therefore, to help in choosing a better experimental design to fulfill one's expectations. We present the rationale underlying the expected relative error computation based on simple binomial distributions. A series of simulated in machina experiments were performed to test the validity of the a priori computation of expected errors, thus confirming the predictions. The step-by-step procedure of the relative error estimation is given. We also discuss the constraints under which an LDA must be performed.

Simulation model of wind turbine gearbox and lubrication system

As increasing efficiency of a wind turbine gearbox, more power can be transferred from rotor blades to generator and less power is used to cause wear and heating in the gearbox. By using a simulation model, behavior of the gearbox can be studied before creating expensive prototypes. The objective of the thesis is to model a wind turbine gearbox and its lubrication system to study power losses and heat transfer inside the gearbox and to study the simulation methods of the used software. Software used to create the simulation model is Siemens LMS Imagine.Lab AMESim, which can be used to create one-dimensional mechatronic system simulation models from different fields of engineering. When combining components from different libraries it is possible to create a simulation model, which includes mechanical, thermal and hydraulic models of the gearbox. Results for mechanical, thermal, and hydraulic simulations are presented in the thesis. Due to the large scale of the wind turbine gearbox and the amount of power transmitted, power loss calculations from AMESim software are inaccurate and power losses are modelled as constant efficiency for each gear mesh. Starting values for simulation in thermal and hydraulic simulations were chosen from test measurements and from empirical study as compact and complex design of gearbox prevents accurate test measurements. In further studies to increase the accuracy of the simulation model, components used for power loss calculations needs to be modified and values for unknown variables are needed to be solved through accurate test measurements.

Doubly fed wind turbine performance in variable grid conditions

Wind turbines based on doubly fed induction generators (DFIG) become the most popular solution in high power wind generation industry. While this topology provides great performance with the reduced power rating of power converter, it has more complicated structure in comparison with full-rated topologies, and therefore leads to complexity of control algorithms and electromechanical processes in the system. The purpose of presented study is to present a proper vector control scheme for the DFIG and overall control for the WT to investigate its behavior at different wind speeds and in different grid voltage conditions: voltage sags, magnitude and frequency variations. The key principles of variable-speed wind turbine were implemented in simulation model and demonstrated during the study. Then, based on developed control scheme and mathematical model, the set of simulation is made to analyze reactive power capabilities of the DFIG wind turbine. Further, the rating of rotor-side converter is modified to not only generate active rated active power, but also to fulfill Grid Codes. Results of modelling and analyzing of the DFIG WT behavior under different speeds and different voltage conditions are presented in the work.

Dynamic Modelling of Circulating Fluidized Bed Plant with Gas Turbine Repowering

Increasing amount of renewable energy source based electricity production has set high load control requirements for power grid balance markets. The essential grid balance between electricity consumption and generation is currently hard to achieve economically with new-generation solutions. Therefore conventional combustion power generation will be examined in this thesis as a solution to the foregoing issue. Circulating fluidized bed (CFB) technology is known to have sufficient scale to acts as a large grid balancing unit. Although the load change rate of the CFB unit is known to be moderately high, supplementary repowering solution will be evaluated in this thesis for load change maximization. The repowering heat duty is delivered to the CFB feed water preheating section by smaller gas turbine (GT) unit. Consequently, steam extraction preheating may be decreased and large amount of the gas turbine exhaust heat may be utilized in the CFB process to reach maximum plant electrical efficiency. Earlier study of the repowering has focused on the efficiency improvements and retrofitting to maximize plant electrical output. This study however presents the CFB load change improvement possibilities achieved with supplementary GT heat. The repowering study is prefaced with literature and theory review for both of the processes to maximize accuracy of the research. Both dynamic and steady-state simulations accomplished with APROS simulation tool will be used to evaluate repowering effects to the CFB unit operation. Eventually, a conceptual level analysis is completed to compare repowered plant performance to the state-of-the-art CFB performance. Based on the performed simulations, considerably good improvements to the CFB process parameters are achieved with repowering. Consequently, the results show possibilities to higher ramp rate values achieved with repowered CFB technology. This enables better plant suitability to the grid balance markets.

Droplet Deposition in the Last Stage of Steam Turbine

During the expansion of steam in turbine, the steam crosses the saturation line and hence subsequent turbine stages run under wet condition. The stages under wet condition run with low efficiency as compared to stages running with supersaturated steam and the life of the last stage cascade is reduced due to erosion. After the steam crosses the saturation line it does not condense immediately but instead it becomes supersaturated which is a meta-stable state and reversion of equilibrium results in the formation of large number of small droplets in the range of 0.05 - 1 μm. Although these droplets are small enough to follow the stream lines of vapor however some of the fog droplets are deposited on the blade surface. After deposition they coagulate into films and rivulets which are then drawn towards the trailing edge of the blade due to viscous drag of the steam. These large droplets in the range of radius 100 μm are accelerated by steam until they impact on the next blade row causing erosion. The two phenomenon responsible for deposition are inertial impaction and turbulent-diffusion. This work shall discuss the deposition mechanism in steam turbine in detail and numerically model and validate with practical data.

Turbines Plans - General Arrangement of Shaft & Cross Section of Turbine, 1903

Two photographs of turbine drawings from the year 1903. The first drawing is titled "10000HP Turbines. Canadian Niagara Power Company. General Arrangement of Shaft." It was last revised 18 May, 1903. The second drawing is titled "10000HP Turbines Canadian Niagara Power Company. Cross Section of Turbine" This drawing revised 6 May, 1903 and 26 June, 1903.

Statement (1 page, handwritten) received of Captain Robert Wells of the Lincoln Militia

Statement (1 page, handwritten) received of Captain Robert Wells of the Lincoln Militia. The names of his men listed are listed on the page. Dec. 15, 1798.

Évaluation de la modélisation et des prévisions de la vitesse du vent menant à l'estimation de la production d'énergie annuelle d'une turbine éolienne

Suite à un stage avec la compagnie Hatch, nous possédons des jeux de données composés de séries chronologiques de vitesses de vent mesurées à divers sites dans le monde, sur plusieurs années. Les ingénieurs éoliens de la compagnie Hatch utilisent ces jeux de données conjointement aux banques de données d’Environnement Canada pour évaluer le potentiel éolien afin de savoir s’il vaut la peine d’installer des éoliennes à ces endroits. Depuis quelques années, des compagnies offrent des simulations méso-échelle de vitesses de vent, basées sur divers indices environnementaux de l’endroit à évaluer. Les ingénieurs éoliens veulent savoir s’il vaut la peine de payer pour ces données simulées, donc si celles-ci peuvent être utiles lors de l’estimation de la production d’énergie éolienne et si elles pourraient être utilisées lors de la prévision de la vitesse du vent long terme. De plus, comme l’on possède des données mesurées de vitesses de vent, l’on en profitera pour tester à partir de diverses méthodes statistiques différentes étapes de l’estimation de la production d’énergie. L’on verra les méthodes d’extrapolation de la vitesse du vent à la hauteur d’une turbine éolienne et l’on évaluera ces méthodes à l’aide de l’erreur quadratique moyenne. Aussi, on étudiera la modélisation de la vitesse du vent par la distributionWeibull et la variation de la distribution de la vitesse dans le temps. Finalement, l’on verra à partir de la validation croisée et du bootstrap si l’utilisation de données méso-échelle est préférable à celle de données des stations de référence, en plus de tester un modèle où les deux types de données sont utilisées pour prédire la vitesse du vent. Nous testerons la méthodologie globale présentement utilisée par les ingénieurs éoliens pour l’estimation de la production d’énergie d’un point de vue statistique, puis tenterons de proposer des changements à cette méthodologie, qui pourraient améliorer l’estimation de la production d’énergie annuelle.

Modélisation statistique de l’érosion de cavitation d’une turbine hydraulique selon les paramètres d’opération

Dans une turbine hydraulique, la rotation des aubes dans l’eau crée une zone de basse pression, amenant l’eau à passer de l’état liquide à l’état gazeux. Ce phénomène de changement de phase est appelé cavitation et est similaire à l’ébullition. Lorsque les cavités de vapeur formées implosent près des parois, il en résulte une érosion sévère des matériaux, accélérant de façon importante la dégradation de la turbine. Un système de détection de l’érosion de cavitation à l’aide de mesures vibratoires, employable sur les turbines en opération, a donc été installé sur quatre groupes turbine-alternateur d’une centrale et permet d’estimer précisément le taux d’érosion en kg/ 10 000 h. Le présent projet vise à répondre à deux objectifs principaux. Premièrement, étudier le comportement de la cavitation sur un groupe turbine-alternateur cible et construire un modèle statistique, dans le but de prédire la variable cavitation en fonction des variables opératoires (tels l’ouverture de vannage, le débit, les niveaux amont et aval, etc.). Deuxièmement, élaborer une méthodologie permettant la reproductibilité de l’étude à d’autres sites. Une étude rétrospective sera effectuée et on se concentrera sur les données disponibles depuis la mise à jour du système en 2010. Des résultats préliminaires ont mis en évidence l’hétérogénéité du comportement de cavitation ainsi que des changements entre la relation entre la cavitation et diverses variables opératoires. Nous nous proposons de développer un modèle probabiliste adapté, en utilisant notamment le regroupement hiérarchique et des modèles de régression linéaire multiple.