Adição de resíduo cerâmico em pastas geopoliméricas para cimentação de poços de petróleo

The development of activities the of oil and gas sector have promoted the search for suitable materials for cementing oil wells. In the state of the Rio Grande do Norte, the integrity of the cement sheath tends to be impaired during steam injection, a procedure necessary to increase oil recovery in reservoirs with low-viscosity oil. The geopolymer is a material that can be used as alternative cement, since it has been used in the production of fire-resistant components, building structures, and for the control of toxic or radioactive residues. Geopolymers result from condensation polymer alkali aluminosilicates and silicates resulting three-dimensional polymeric structures. They are produced in a manner different from that of Portland cement, which is made an activating solution that is mixed with geopolymer precursor. Among the few works studied allowed us to conclude that the pastes prepared with metakaolin as precursor showed better performance of its properties. Several studies show the addition of waste clay as a means of reducing cost and improving end of the folder properties. On this basis, the goal is to study the influence of the addition of ceramic waste in geopolymer paste. To develop the study of rheology tests were carried out, filtered, thickening time, compressive strength, free water, specific gravity and permeability, according to the American Pretoleum Institute (API). The results for all formulations studied show that the folders have high mechanical strength to a light paste; low filtrate volume, absence of free water, very low permeability, slurry, consistent with a light paste, and thickening time low that can be corrected with the use of a retardant handle. For morphological characterization, microstructural, physical, chemical and thermal tests were carried out by XRD, MEV, DTA, TG, FTIR. In the trial of XRD, it was found that geopolymer is an amorphous material, with a peak of crystalline kaolinite. In tests of TG / DTA, revealed the presence of a significant event, which represents the mass loss related to water, and also observed the reduction of weight loss by increasing the concentration of ceramic waste. In the trial of MEV, we found a uniform matrix without the presence of other phases. In the trial of FT-IR, we observed the presence of the band related to water. From all results it was determined that the optimum concentration range of use is between 2.5 and 5% of waste ceramic

Estudio del efecto del procesamiento termo mecánico sobre los parámetros de formabilidad en aceros IF para aplicaciones automotrices

En el presente trabajo de investigación se analizó un acero libre de elementos intersticiales estabilizado con Titanio o mejor conocido como acero IF (por sus siglas en inglés Interstitial Free), denominado por la empresa EDDS (Extra Deep Drawing Steel) el cual se utiliza en partes exteriores de los vehículos en donde se requiere que la lámina a estampar cumpla con propiedades muy altas de ductilidad y baja resistencia. Se obtuvo acero IF en sus distintas etapas de procesamiento termo mecánico comenzando por material laminado en caliente, material laminado en frio y por ultimo material recocido y galvanizado en planta, esto con el objetivo de caracterizar y evaluar las propiedades mecánicas de cada etapa. De la etapa final del acero (recocido y galvanizado de planta) se obtuvieron los parámetros de formabilidad (n y R) mediante una prueba de tensión para poder establecer las condiciones a superar con las experimentaciones. El objetivo principal en el laboratorio fue el mejorar, mediante diferentes variables de recocido (tiempo y temperatura) en los tratamientos térmicos, los parámetros n= 0.23 y R=1.56 producidos en planta, y lograr obtener mediante nuevos tratamientos térmicos valores de R> 1.56 al igual que valores de n>0.23. Para simular las temperaturas con tiempos cortos de recocido se implementó un calentamiento por inducción en la bobina del laboratorio. Se pudieron realizar solo 2 pruebas debido al material disponible para este experimento. Ambos experimentos resultaron en una notable mejoría del valor de Lankford R (utilizado como un indicador en la formabilidad de hojas de acero), así como del exponente de endurecimiento por deformación (n), y se logró mantener un poco por encima sus propiedades de esfuerzo de cedencia, esfuerzo último y por ciento de elongación a las obtenidas por el proceso de recocido realizado en planta.

Formulação de bloco intertravado cerâmico com adição de resíduos urbanos e industriais

The production of waste from urban and industrial activities is one of the factors of environmental contamination and has aroused attention of the scientific community, in the sense of its reuse. On the other hand, the city of Salvador/Ba, with approximately 262 channels, responsible for storm water runoff, produces every year, by the intervention of cleaning and clearing channels, a significant volume of sediments (dredged mud), and thus an appropriate methodology for their final destination. This study aims to assess the influence of incorporation of these tailings in arrays of clay for production of interlocked block ceramic, also known as ceramic paver. All the raw materials from the metropolitan region of Salvador (RMS) were characterized by x-ray fluorescence, x-ray diffraction, thermal analysis (TG and TDA), particle size analysis and dilatometry. With the use of statistical experimental planning technique, ternary diagram was defined in the study region and the analyzed formulations. The specimens were prepared with dimensions of 60x20x5mm³, by uniaxial pressing of 30 MPa and after sintering at temperatures of 900°, 1000º and 1100ºC the technological properties were evaluated: linear shrinkage, water absorption, apparent porosity, apparent specifies mass, flexural rupture and module. For the uniaxial compression strength used cylindrical probe body with Ø 50 mm. The standard mass (MP) was prepared with 90% by weight of clay and 10% by weight of Channel sediment (SCP), not being verified significant variations in the properties of the final product. With the incorporation of 10% by weight of manganese residue (PFM) and 10% by weight of the Ceramic waste (RCB) in the mass default, in addition to adjusting the plasticity due to less waste clay content, provided increased linear firing shrinkage, due the significant concentration of K2O, forming liquid phase at low temperature, contributing to decreased porosity and mechanical resistance, being 92,5 MPa maximum compressive strength verified. After extract test leachate and soluble, the piece containing 10% of the PFM, was classified as non-hazardous and inert material according to NBR10004/04 ABNT. The results showed the feasibility on using waste, SCP, RCB and PFM clay mass, at temperatures above 900ºC, paver ceramic production, according to the specifications of the technical standards, so that to exceed the 10% of the PFM, it becomes imperative to conduct studies of environmental impacts

Incorporação de resíduo cerâmico para prevenção da retrogressão da resistência de cimentos de poços de petróleo submetidos à injeção de vapor

Steam injection is the most used thermal recovery method of oil nowadays because of the high degree of development of the technique that allows high recovery factors. However, injection of superheated steam into the reservoir affects the entire structure of the well, including the cemented layer that presents a retrogression of compressive strength and increases the permeability due to formation of more crystalline and denser phases at temperatures above 110 °C. These changes result in failures in the cement that favor the entrance of formation fluids into the annulus space resulting in unsafe operations and restrictions in the economic life of the well. But the strength retrogression can be prevented by partial replacement of cement by silica-based materials that reduce the CaO/SiO2 ratio of cement slurries changing the trajectory of the reactions, converting those deleterious phases in phases with satisfactory mechanical strength and permeability. The aim of this study was to evaluate the behavior of a ceramic waste material rich in silica in partial and total substitution of a mineral additive used to fight the strength retrogression of cement slurries subjected to high temperatures. The evaluation was made by compression, X-ray diffraction (XRD) and thermogravimetry (TG/DTG). The samples were submitted to a cycle of low temperature (38 °C) for 28 days and a cycle of low temperature followed by exposure to 280 ºC and 1000 psi by 3 days. The results showed that slurries with additions of up to 30% of the waste material are not enough to prevent the strength retrogression, while slurries with additions of the waste material combined with silica flour in various proportions produced hydrated products of low Ca/Si ratios that maintained the compressive strength at satisfactory levels

Avaliação da resistência mecânica de material leve utilizando misturas de pedaços de pneus com solo do Distrito Federal

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Civil e Ambiental, 2016.

Efeito da adição de cargas minerais leves na resistência mecânica de grautes para cimentação de poços offshore

The preparation of cement slurries for offshore well cementing involves mixing all solid components to be added to the mixing water on the platform. The aim of this work was to study the formulation of pre-prepared dry mixtures, or grouts, for offshore oilwell cementing. The addition of mineral fillers in the strength of lightweight grouts applied for depths down to 400 m under water depths of 500 m was investigated. Lightweight materials and fine aggregates were selected. For the choice of starting materials, a study of the pozzolanic activity of low-cost fillers such as porcelain tile residue, microsilica and diatomaceous earth was carried out by X-ray diffraction and mechanical strength tests. Hardened grouts containing porcelain tile residue and microsilica depicted high strength at early ages. Based on such preliminary investigation, a study of the mechanical strength of grouts with density 1.74 g/cm3 (14.5 lb/gal) cured initially at 27 °C was performed using cement, microsilica, porcelain tile residue and an anti-foaming agent. The results showed that the mixture containing 7% of porcelain tile residue and 7% of microsilica was the one with the highest compressive strength after curing for 24 hours. This composition was chosen to be studied and adapted for offshore conditions based on testes performed at 4 °C. The grout containing cement, 7% of porcelain tile residue, 7% of active silica and admixtures (CaCl2), anti-foaming and dispersant resulted satisfactory rheology and mechanical strength after curing for 24 hours of curing

Oxigenoterapia e ventilação mecânica em atenção domiciliar - ATENÇÃO DOMICILIAR

Módulo da Atenção Domiciliar, compõe o curso Oxigenoterapia e Ventilação Mecânica em Atenção Domiciliar, com carga horária de 45 horas. Este é um dos cursos do Programa Multicêntrico de Qualificação Profissional em Atenção Domiciliar a Distância, produzido pelo Núcleo de Educação em Saúde Coletiva da Universidade Federal de Minas Gerais (Nescon/UFMG) sob a coordenação do MS/SGTES-UNASUS. Suas atividades são autoinstrucionais e sua temática desenvolve-se por meio das seguintes unidades educacionais: Unidade 1 – Oxigenoterapia (Conceitos e princípios; indicações e fontes de oxigênio; sistemas e dispositivos para oxigenoterapia). Unidade 2 – Ventilação mecânica ( Conceitos e princípios; ventilação mecânica não invasiva: ventiladores e acessórios; modos e modalidades ventilatórias, indicações, contraindicações e complicações). Unidade 3 – Traqueostomia (Conceito; Cânula de traqueostomia: indicações e tipos; plano de cuidado individual para a pessoa traqueostomizada em atenção domiciliar). Unidade 4 – Avaliação e fisioterapia respiratória (Avaliação respiratória; fisioterapia respiratória: classificação e indicação de técnicas fisioterapêuticas).

Oxigenoterapia e ventilação mecânica em atenção domiciliar - ATENÇÃO DOMICILIAR

Módulo da Atenção Domiciliar, compõe o curso Oxigenoterapia e Ventilação Mecânica em Atenção Domiciliar, com carga horária de 45 horas. Este é um dos cursos do Programa Multicêntrico de Qualificação Profissional em Atenção Domiciliar a Distância, produzido pelo Núcleo de Educação em Saúde Coletiva da Universidade Federal de Minas Gerais (Nescon/UFMG) sob a coordenação do MS/SGTES-UNASUS. Suas atividades são autoinstrucionais e sua temática desenvolve-se por meio das seguintes unidades educacionais: Unidade 1 – Oxigenoterapia (Conceitos e princípios; indicações e fontes de oxigênio; sistemas e dispositivos para oxigenoterapia). Unidade 2 – Ventilação mecânica ( Conceitos e princípios; ventilação mecânica não invasiva: ventiladores e acessórios; modos e modalidades ventilatórias, indicações, contraindicações e complicações). Unidade 3 – Traqueostomia (Conceito; Cânula de traqueostomia: indicações e tipos; plano de cuidado individual para a pessoa traqueostomizada em atenção domiciliar). Unidade 4 – Avaliação e fisioterapia respiratória (Avaliação respiratória; fisioterapia respiratória: classificação e indicação de técnicas fisioterapêuticas).

Avaliação antropométrica: peso de crianças menores de 2 anos em balaça mecânica

Material utilizado na unidade 2 do módulo de Alimentação e Nutrição do curso de especialização em Saúde da Família produzido pela UNA-SUS/UFMA, com apresentação visual trabalhada para atender aos alunos participantes do programa Mais Médicos. Trata-se de adaptação de material do Ministério da Saúde que apresenta os passos para aferir o peso de crianças menores de 2 anos em balança pediátrica mecânica.

Avaliação antropométrica: peso de crianças maiores de 2 anos, adolescentes e adultos em balança mecânica

Material utilizado na unidade 2 do módulo de Alimentação e Nutrição do curso de especialização em Saúde da Família produzido pela UNA-SUS/UFMA, com apresentação visual trabalhada para atender aos alunos participantes do programa Mais Médicos. Material adaptado do Ministério da Saúde que apresenta os passos para aferir o peso de crianças maiores de 2 anos, adolescentes e adultos em balança mecânica de plataforma.

Estudo vídeo-polissonográfico em recém-nascidos de termo pequenos para a idade gestacional

Video-polygraphic-EEG studies were performed in the first 24 life-hours of 26 healthy full-term newborns without perinatal injuries. The neurological examination and cranial ultrasonography were normal. The newborns were divided into two groups: one, with full-term appropriate - birth weight 11 newborns (control group ) and the other with full-term low-birth weight 15 newborns. Thirteen newborns of the second group had video-polygraphic-EEG study abnormalities. The most frequent abnormalities were found in 11 cases, as far as sleep architecture is concerned. Also, when compared with the control group, 8 cases of an excessive amount of startles and 2 cases of low behavior activities were found. The results demonstrate the usefulness of video-polygraphic-EEG study in the full-term newborns with intra-uterine growth retard. This examination was sensitive to detect behavior, sleep architecture and EEG standard differences in the low birth-weight newborns as to the control group.

Resistência à compressão e remoção de folhas da cana-de-açúcar visando à colheita mecânica

Sugarcane holds an important place in the Brazilian economy. Grate part of the sugarcane harvested still accomplished largely manually. Sugarcane harvesters available in Brazil use the technology to chop the cane into 200 to 300 mm billets to allow on the go cane transferring to transport, contradicting the traditional method of whole stalk sugarcane harvesting system. In order to make whole stalk mechanical harvesting system possible, one of the barriers to be expired is the mechanical removal of the straw. The design of a mechanism that accomplishes this operation depends directly on the knowledge of the mechanical properties of the sugarcane related to its resistance to compression and the forces necessary to remove the leaves from the stalk. Compression tests were conducted using the universal testing machine. For leaves removal test by friction, a special apparatus was designed to allow the registration of the normal and traction force. The sugarcane stalk can resist up to 4.9 MPa. With a normal pressure of 0.8 MPa, which correspond to a friction force of 315 N, it is possible to remove the leaves, independent of its location in the sugarcane stalk.

Caracterização física e mecânica de argamassas à base de cimento Portland e cinza de casca de arroz residual

Rice husk, employed as an energy source at milling industries in Brazil generates, after burning, a dark ash. This residue is not yet conveniently disposed, being currently dumped on large areas, causing environmental problems. This research intended to evaluate the applications of residual rice husk ashes (RHA) as a partial replacement of cement for mortar production. Rice husk ash was chemically characterized through X-ray fluorescence, determination of carbon content, X-ray diffraction, and laser granulometric analysis. Mortar specimens were submitted to two different exposure conditions: internal and external environments at a maximum period of five months. Physical-mechanical testing were compressive strength and ultrasonic pulse velocity (UPV). Although presenting good mechanical performance, the mortar based on ash (RHA) did not present pozolanicity but it can be employed in cement matrices as inert material (filler).

Avaliação do amaciamento de carne bovina de dianteiro (Triceps brachii) pelos métodos de maturação, estimulação elétrica, injeção de ácidos e tenderização mecânica

Twenty-two Triceps brachii muscle obtained from 11 cows aged 3 and 4 years , killed in an experimental slaughter plant, were submitted to mechanical tenderization, injection with acetic acid 0,1M and lactic acid 0,2M, ageing for 9 and 14 days and electrical stimulation (250v - 60Hz - 90s), some of them were reserved as a control group, without treatment. The 14 days ageing time presented 21% of increase in subjective tenderness and 12% of reduction in shear force, these values were similar to the electrical stimulated meat. However the injection with acids and the ageing time 9 days did not present significant effect in the texture. Although the shear force values of mechanical tenderized meat was the shortest among all treatments, suspect of superestimation because of the fractures plan created by this process. Another analyses were carried out: pH reduction curve, R value; colour analysis; weight losses by cooking and by treatment; and microbiological analysis.

Ocorrência de fungos filamentosos termo-resistentes em polpa de tomate envasada assepticamente

This work aimed at determining the occurrence of heat resistant molds during the aseptic processing of tomato pulp (8° BRIX). During tomato harvest, 9 lots were sampled (3 at the beginning, 3 at the apex and 3 at the end of harvest) and other 5 lots were sampled between harvest. For each lot, the enumeration of heat resistant molds was carried out in samples collected during the aseptic process. The mean count of heat resistant molds was relatively low, ranging from <1 to 8CFU/100mL of sample. The higher counts were observed in the raw material and the pre-wash and transportation water. Fifty strains of heat resistant molds detected in the enumeration procedure were isolated, codified and stocked. One-month-old spores of each isolate were submitted to different heat shocks to select the most heat resistant mold. The most heat resistant isolated strain (survived 100° C/25 minutes) was identified as Neosartorya fischeri.