The data base : the potential for energy conservation in nine selected industries /

v.1. Selected plastics.--v.2. Petroleum refining.--v.3. Cement.--v.4. Copper.--v.5. Aluminum.--v.6. Steel.--v.7. Glass.--v.8. Selected paper products.--v.9.Styrene butadiene rubber.

Ultrasonic degradation of butadiene, styrene and their copolymers

Ultrasonic degradation of commercially important polymers, styrene-butadiene (SBR) rubber, acrylonitrile-butadiene (NBR) rubber, styrene-acrylonitrile (SAN), polybutadiene rubber and polystyrene were investigated. The molecular weight distributions were measured using gel permeation chromatography (GPC). A model based on continuous distribution kinetics approach was used to study the time evolution of molecular weight distribution for these polymers during degradation. The effect of solvent properties and ultrasound intensity on the degradation of SBR rubber was investigated using different pure solvents and mixed solvents of varying volatility and different ultrasonic intensities. (C) 2011 Elsevier B.V. All rights reserved.

Polystyrene and asphaltene micelles within blends with a bitumen of an SBS block copolymer and styrene and butadiene homopolymers

Using fluorescence microscopy, DSC and DMTA we have explored blends of a bitumen with a styrene-butadiene-styrene (SBS) block copolymer, and with blends of the bitumen with SBS and one or two homopolymers - a polystyrene and a poly(cis-butadiene). The SBS polymer was progressively replaced with quantities of the homopolymers both together in the proportions found in the block copolymer and then by each homopolymer separately. At low temperatures the blends are all softer than the bitumen itself, so the polymers plasticise the bitumen-rich phase, and above 50°C the blends' stiffness (E') falls below a plateau only when a critical proportion of the block copolymer has been replaced with the two homopolymers: this supports the idea of an extensive network created by the polystyrene-rich spherical microphases that is effective even when the polystyrene microphases have melted. In one polymer blend the stiffness rose as the temperature was raised above 100°C, suggesting the development of a mesophase based upon polybutadiene plus asphaltenes, in another E' was enhanced and E" remained constant as the temperature rose above 70°C, perhaps for a similar reason; in some loss process appeared and the stiffness fell as temperature rose; but in others a good part of the SBS was replaced by either polystyrene or polybutadiene without changing the appearance of a rubbery plateau, that is, without a diminution of the mechanical properties of the soft matter.

Deformation mechanism of polystyrene toughened with sub-micrometer monodisperse rubber particles

Core-shell polybutadiene-graft-polystyrene (PB-g-PS) rubber particles with different ratios of polybutadiene to polystyrene were prepared by emulsion polymerization through grafting styrene onto polybutadiene latex. The weight ratio of polybutadiene to polystyrene ranged from 50/50 to 90/10. These core-shell rubber particles were then blended with polystyrene to prepare PS/PB-g-PS blends with a constant rubber content of 20 wt%. PB-g-PS particles with a lower PB/PS ratio (<= 570/30) form a homogeneous dispersion in the polystyrene matrix, and the Izod notched impact strength of these blends is higher than that of commercial high-impact polystyrene (HIPS). It is generally accepted that polystyrene can only be toughened effectively by 1-3 mu m rubber particles through a toughening mechanism of multiple crazings. However, the experimental results show that polystyrene can actually be toughened by monodisperse sub-micrometer rubber particles. Scanning electron micrographs of the fracture surface and stress-whitening zone of blends with a PB/PS ratio of 70/30 in PB-g-PS copolymer reveal a novel toughening mechanism of modified polystyrene, which may be shear yielding of the matrix, promoted by cavitation.

Dynamic mechanical studies of the sulfonated butyl rubber ionomers and their blends

Dynamic mechanical properties of sulfonated butyl rubber ionomers neutralized with different amine or metallic ion (zinc or barium) and their blends with polypropylene (PP), high-density polyethylene (HDPE), or styrene-butadiene-styrene (SBS) triblock copolymer were studied using viscoelastometry. The results showed that glass transition temperatures of ion pair-containing matrix and ionic domains (T-g1 and T-g2, respectively) of amine-neutralized ionomers were lower than those of ionomers neutralized with metallic ions, and the temperature range of the rubbery plateau on the storage modulus plot for amine-neutralized ionomers was narrower. The modulus of the rubbery plateau for amine-neutralized ionomers was lower than that of ionomers neutralized with zinc or barium ion. With increasing size of the amine, the temperature range for the rubbery plateau decreased, and the height of the loss peak at higher temperature increased. Dynamic mechanical properties of blends of the zinc ionomer with PP or HDPE showed that, with decreasing ionomer content, the T-m of PP or HDPE increased and T-g1 decreased, whereas T-g2 or the upper loss peak temperature changed only slightly. The T-g1 for the blend with SBS also decreased with decreasing ionomer content. The decrease of T-g1 is attributed to the enhanced compatibilization of the matrix of the ionomer-containing ion pairs with amorphous regions of PP or HDPE or the continuous phase of SBS due to the formation of thermoplastic interpenetrating polymer networks by ionic domains and crystalline or glassy domains.

Copolymerization of styrene with butadiene and isoprene using a rare earth catalyst

In the copolymerization of styrene-butadiene and styrene-isoprene, a novel rare earth catalyst system (CF3CO2)(3)Ln/R(3-n)AlH(n)/(CH3)(3)CCH2Br (Ln = Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb and Lu; R = Me-, Et-, i-Bu-, and Oct-; n = 0 and 1) has been studied. The 1, 4 unit contents in the copolymers obtained are found to range from 64.4 to 99.6% with St contents of 5.2 to 59.9%, and intrinsic viscosities of 0.1 to 0.5 dl g(-1) measured by i.r., H-1 n.m.r. and C-13 n.m.r. spectra. From the calculated data of linked ratios, a change in the microstructure is induced by the styrene unit, probably adjacent to the butadiene or isoprene unit. An interesting result is that the ratios of styrene unit linked with 1, 2 or 3,4 units in the copolymers are far higher than in copolymers obtained with the nickel catalyst. The experimental results are discussed in terms of rare earth pi-allyl coordination and back-biting mechanism.

Use of scrap tire rubber in place of SBS in modified asphalt as an environmentally correct alternative for Brazil

Reusing scrap tires has become a worldwide challenge, especially due to the great difficulty in finding ecologically and economically feasible ways to dispose of them. This has led to the creation of specific programs and legislation for reusing scrap tires. Research has shown that a certain percentage of scrap tire rubber can be added to asphalt compositions, and this has become a worldwide practice. This paper describes the properties of four asphalt compositions modified with scrap tire rubber (STR) prepared in the laboratory. These properties are then compared with those of asphalt modified with styrene butadiene styrene (SBS), a synthetic polymer and one of the most common modifiers, to verify the feasibility of using scrap tire rubber as a substitute for SBS. The scope of this study does not include an analysis of how STR affects end-of-life asphalt. The main findings indicate that STR is a potential substitute of SBS in paving material, and although it does not meet some of the standard specifications when compared with SBS, these issues can be overcome by proper care during storage and transportation. The substitution of SBS by STR also showed the potential for about 10% in expenditure savings. (C) 2012 Elsevier Ltd. All rights reserved.

Influence of the molecular architecture on the secondary relaxations of Poly(styrene-co-methylmethacrylate) copolymers

The processes of adsorption of grafted copolymers onto negatively charged surfaces were studied using a dissipative quartz crystal microbalance (D-QCM) and ellipsometry. The control parameters in the study of the adsorption are the existence or absence on the molecular architecture of grafted polyethyleneglycol (PEG) chains with different lengths and the chemical nature of the main chain, poly(allylamine) (PAH) or poly(L-lysine) (PLL). It was found out that the adsorption kinetics of the polymers showed a complex behavior. The total adsorbed amount depends on the architecture of the polymer chains (length of the PEG chains), on the polymer concentration and on the chemical nature of the main chain. The comparison of the thicknesses of the adsorbed layers obtained from D-QCM and from ellipsometry allowed calculation of the water content of the layers that is intimately related to the grafting length. The analysis of D-QCM results also provides information about the shear modulus of the layers, whose values have been found to be typical of a rubber-like polymer system. It is shown that the adsorption of polymers with a charged backbone is not driven exclusively by the electrostatic interactions, but the entropic contributions as a result of the trapping of water in the layer structure are of fundamental importance.

Investigación de mezclas de caucho, con bajo contenido en cloro, para bandas transportadoras con características ignífugas

El objeto de la tesis doctoral se centra en la obtención de una banda transportadora de minería exenta de halógenos o al menos con el menor contenido posible, es por ello que se ha realizado un estudio de diferentes matrices poliméricas sin halógenos y se han evaluado diferentes sistemas ignifugantes. Se ha partido de mezclas con base polimérica de caucho natural y de estireno butadieno ya que son cauchos sin halógenos y con los que se pueden obtener mezclas de buenas propiedades mecánicas. Los resultados obtenidos durante el desarrollo de la tesis han sido muy satisfactorios, ya que se fabricaron bandas a gran escala para poder realizar los ensayos descritos en la normativa UNE EN 14973. La clasificación adquirida, categoría B1, alcanza dos de los objetivos marcados al inicio de los trabajos de investigación, y por tanto puede dar lugar a: - La fabricación a nivel industrial - La comercialización de una banda retardante de llama para minería y obra subterránea, formulada con un nuevo aditivo que reduce notablemente el contenido en cloro. - Disminución de la contaminación derivada de los humos tóxicos producidos cuando una banda transportadora arde accidentalmente. Los aditivos retardantes de llama sin halógenos, son muy efectivos en dosis elevadas, para la obtención de mezclas con propiedades ignífugas, pero las propiedades mecánicas de las mezclas se debilitan. Se ha buscado un compromiso entre las propiedades ignífugas y mecánicas, por lo que resulta adecuado obtener aditivos que posean un tamaño de partícula tal que actúen como cargas semi-reforzantes para poder utilizarlos en mayor proporción y así poder conseguir las propiedades ignífugas deseadas sin alterar de forma significativa las demás propiedades de la mezcla. ABSTRACT The purpose of this thesis is to obtain a mining conveyor belt with minimal halogen content, with the final objective of being halogen-free. Several polymer matrices without halogen and as well as fireproof systems have been analyzed to achieve this goal. The polymer mixtures studied are based on natural rubber and styrene butadiene, due to the fact that are rubbers without halogens and which their mixtures have good mechanical properties. The outcome of the thesis research is satisfactory, since the results are manufactured conveyor belts that comply with the tests described in the UNE EN 14973. The obtained B1 classification achieves two objectives set at the beginning of the research, and therefore can lead to: - Manufacturing at industrial level - Marketing of a flame retardant conveyor belt for mining and underground works formulated with a new additive that significantly reduces the chlorine content - Reduce pollution produced of the toxic fumes generated when a conveyor accidentally burns Additive flame retardant halogen-free are very effective in high doses to obtain blends with flame retardant properties, but the mechanical properties of the blends are below standards. A compromise between the fire retardant and mechanical properties has been successfully obtained, making possible to obtain additives that show a particle size that act as semi-reinforcing load in order to use a greater extent and thus be able to achieve the pursued fire retardant properties without altering significant other properties of mixture.

Influence of montmorillonite on syndiotactic polymerization behavior of styrene

The influence of montmorillonite (MMT) on the syndiotactic polymerization behavior of styrene was studied. To avoid the hydrophilic surface of the MMT coming into contact with the catalyst, which could poison it, SAN was introduced between the MMT and Cp*Ti (OCH3)(3). MMT was introduced into the catalytic system as a supporter for the Ti catalyst (supported catalytic system) or just dispersed in the polymerization solvent directly (in situ polymerization system). The polymerization results showed that surface modification of MMT dramatically affected the catalytic activity as well as the syndiotacticity of the polymers. This is mainly explained by the insulator SAN preventing the formation of the inactive/little active species Si-O-Ti and other atactic active species resulting from the reaction of the -OH on the MMT layer surface with Cp*Ti(OCH3)(3).

The effect of preparation conditions on the catalyst Nd(P-507)(3)/H2O/Al(i-Bu)(3) for the polymerization of styrene

The catalyst system neodymium phosphonate Nd(P-507)(3)/H2O/Al(i-Bu)(3) for the polymerization of styrene was examined. Effects of the addition order of the catalyst components, catalyst aging time and aging temperature on the catalyst activity and the polymer characteristics were investigated. The catalyst activity for isospecific polymerization of styrene increases with aging time and reaches the maximum with a catalyst aged for 45 min at 70 degrees C. The aging time that the catalyst needs to reach the highest activity for isospecific polymerization decreases with increasing aging temperature. The preformed catalyst and the in situ catalyst were compared with respect to the kinetic behavior of the styrene polymerization and the polymer characteristics.

Compatibilization effect of graft copolymer on immiscible polymer blends: 1. LLDPE/SBS/LLDPE-g-PS systems

compatibilizing effect of graft copolymer, linear low density polyethylene-g-polystyrene (LLDPE-g-PS), on immiscible blends of LLDPE with styrene-butadiene-styrene triblock copolymer (SBS) has been investigated by means of C-13 CPMAS n.m.r. and d.s.c. techniques. The results indicate that LLDPE-g-PS is an effective compatibilizer for LLDPE/SBS blends. It was found that LLDPE-g-PS chains connect two immiscible components, LLDPE and SBS, through solubilization of chemically identical segments of LLDPE-g-PS into the amorphous region of LLDPE acid PS block domain of SBS, respectively. It was also found that LLDPE-g-PS chains connect the crystalline region of LLDPE by isomorphism, with serious effects on the supermolecular structure of LLDPE. The effect of LLDPE-g-PS on the supermolecular structure of LLDPE in the LLDPE/SBS blends obviously depends on the composition of the blends, but has little dependence on the PS grafting yields of LLDPE-g-PS. (C) 1998 Elsevier Science Ltd. All rights reserved.

Rheological studies on the phase dissolution in a block copolymer

The microphase transition in a styrene-butadiene-styrene triblock copolymer was studied by rheometric mechanical spectroscopy. A high-temperature-melt rheological transition from the highly elastic, nonlinear viscous behavior typical of a multiphase structure to linear viscous behavior with insignificant elasticity typical of a single-phase structure was observed. The transition temperature is determined according to the discontinuity of the rheological properties across the transition region, which agrees well with the results obtained from the small angle X-ray scattering data and the expectation of the random phase approximation theory. Maybe for the first time, microphase dissolution was investigated theologically. The storage modulus (G') and the loss modulus (G '') increase with time during the process. An entanglement fluctuation model based on the segmental density fluctuations is presented to explain the rheological behavior in this dissolution process. (C) 1997 John Wiley & Sons.

Velocidade da corrosão do aço em argamassas cimentícias modificadas com polímeros

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Química