The appraisal of anaerobic digestion in Ireland to develop improved designs and operational practice

Mesophilic Anaerobic Digestion treating sewage sludge was investigated at five full-scale sewage treatment plants in Ireland. The anaerobic digestion plants are compared and evaluated in terms of design, equipment, operation, monitoring and management. All digesters are cylindrical, gas mixed and heated Continuously Stirred Tank Reactors (CSTR), varying in size from 130m3 to 800m3. Heat exchanger systems heat all digesters. Three plants reported difficulties with the heating systems ranging from blockages to insufficient insulation and design. Exchangers were modified and replaced within one year of operation at two plants. All but one plant had Combined Heat and Power (CHP) systems installed. Parameter monitoring is a problem at all plants mainly due to a lack of staff and knowledge. The plant operators consider pH and temperature the most important parameters to be measured in terms of successful monitoring of an anaerobic digester. The short time taken and the ease at which pH and temperature can be measured may favour these parameters. Three laboratory scale pilot anaerobic digesters were operated using a variety of feeds over at 144-day period. Two of the pilots were unmixed and the third was mechanically mixed. As expected the unmixed reactors removed more COD by retention of solids in the digesters but also produced greater quantities of biogas than the mixed digester, especially when low solids feed such as whey was used. The mixed digester broke down more solids due to the superior contact between the substrate and the biomass. All three reactors showed good performance results for whey and sewage solids. Scum formation occurred giving operational problems for mixed and unmixed reactors when cattle slurry was used as the main feed source. The pilot test was also used to investigate which parameters were the best indicators of process instability. These trials clearly indicated that total Volatile Fatty Acid (VFA) concentrations was the best parameter to show signs of early process imbalance, while methane composition in the biogas was good to indicate possible nutrient deficiencies in the feed and oxygen shocks. pH was found to be a good process parameter only if the wastewater being treated produced low bicarbonate alkalinities during treatment.

Optimisation of a surface mount technology process using a SnAgCu lead-free alloy

The impending introduction of lead-free solder in the manufacture of electrical and electronic products has presented the electronics industry with many challenges. European manufacturers must transfer from a tin-lead process to a lead-free process by July 2006 as a result of the publication of two directives from the European Parliament. Tin-lead solders have been used for mechanical and electrical connections on printed circuit boards for over fifty years and considerable process knowledge has been accumulated. Extensive literature reviews were conducted on the topic and as a result it was found there are many implications to be considered with the introduction of lead-free solder. One particular question that requires answering is; can lead-free solder be used in existing manufacturing processes? The purpose of this research is to conduct a comparative study of a tin-lead solder and a lead-free solder in two key surface mount technology (SMT) processes. The two SMT processes in question were the stencil printing process and the reflow soldering process. Unreplicated fractional factorial experimental designs were used to carry out the studies. The quality of paste deposition in terms of height and volume were the characteristics of interest in the stencil printing process. The quality of solder joints produced in the reflow soldering experiment was assessed using x-ray and cross sectional analysis. This provided qualitative data that was then uniquely scored and weighted using a method developed during the research. Nested experimental design techniques were then used to analyse the resulting quantitative data. Predictive models were developed that allowed for the optimisation of both processes. Results from both experiments show that solder joints of comparable quality to those produced using tin-lead solder can be produced using lead-free solder in current SMT processes.

Approximations of the Fisher information for the construction of efficient experimental designs in nonlinear mixed effects models

Magdeburg, Univ., Fak. für Mathematik, Diss., 2012

Optimal designs for mixed effects poisson regression models

Magdeburg, Univ., Fak. für Mathematik, Diss., 2010

Optimal designs for multivariate linear models

Magdeburg, Univ., Fak. für Mathematik, Diss., 2013

Optimal designs for the prediction in hierarchical random coefficient regression models

Magdeburg, Univ., Fak. für Mathematik, Diss., 2015

On convergence of the maximum likelihood estimator in adaptive designs

Otto-von-Guericke-Universität Magdeburg, Fakultät für Mathematik, Dissertation, 2016

Auctions for government securities: a laboratory comparison of uniform, discriminatory and spanish designs

The Bank of Spain uses a unique auction format to sell government bonds, which can be seen as a hybrid of a uniform and a discriminatory auction. For winning bids above the average winning bid, buyers are charged the average winning bid, otherwise they pay their respective bids. We report on an experiment that compares this auction format to the discriminatory format, used in most other countries, and to the uniform format. Our design is based on a common value model with multi-unit supply and two-unit demand. The results show significantly higher revenue with the Spanish and the uniform formats than with the discriminatory one, while volatility of prices over time is significantly lower in the discriminatory format than in the Spanish and uniform cases. Actual price dispersion is significantly larger in the discriminatory than in the Spanish. Our data also exhibit the use of bid-spreading strategies in all three designs.

Testing of stair climbing point-of-choice prompts in Barcelona at an outdoor set of stairs and scalators on the Montjuïc site

Regular stair climbing has well-documented health dividends, such as increased fitness and strength, weight loss and reduced body fat, improved lipid profiles and reduced risk of osteoporosis. The general absence of barriers to participation makes stair climbing an ideal physical activity (PA) for health promotion. Studies in the US and the UK have consistently shown that interventions to increase the accumulation of lifestyle PA by climbing stairs rather than using the escalators are effective. However, there are no previous in Catalonia. This project tested one message for their ability to prompt travelers on the Montjuïc site to choose the stairs rather than the escalator when climbing up the Monjuïc hill. One standard message, " Take the stairs! 7 minutes of stair climbing a day protects your heart" provided a comparison with previous research done in the UK. Translated into Catalan and Spanish, it was presented on a poster positioned at the point of choice between the stairs and the escalator. The study used a quasi-experimental, interrupted time series design. Travelers, during several and specific hours on two days of the week, were coded for stair or escalator use, gender, age, ethnic status, presence of accompanying children or bags by one observer. Overall, the intervention resulted in a 81% increase in stair climbing. In the follow-up period without messages, stair climbing dropped out to baseline levels. This preliminary study showed a significant effect on stair use. However, caution is needed since results are based on a small sample and, only a low percentage of the sample took the stairs at baseline or the intervention phase . Future research on stair use in Catalonia should focus on using bigger samples, different sites (metro stations, airports, shopping centers, etc) , different messages and techniques to promote stair climbing.

Optimal asymptotic bounds for spherical designs

"Vegeu el resum a l'inici del document del fitxer adjunt"

Multi-stage oligopoly models with nested logit demand structures: A simplifying approach

Solving multi-stage oligopoly models by backward induction can easily become a com- plex task when rms are multi-product and demands are derived from a nested logit frame- work. This paper shows that under the assumption that within-segment rm shares are equal across segments, the analytical expression for equilibrium pro ts can be substantially simpli ed. The size of the error arising when this condition does not hold perfectly is also computed. Through numerical examples, it is shown that the error is rather small in general. Therefore, using this assumption allows to gain analytical tractability in a class of models that has been used to approach relevant policy questions, such as for example rm entry in an industry or the relation between competition and location. The simplifying approach proposed in this paper is aimed at helping improving these type of models for reaching more accurate recommendations.

One-tube nested Polymerase Chain Reaction for detection of Chlamydia trachomatis

Here we present a one-tube nested PCR test, which allows the detection of minimal quantities of Chlamydia trachomatis in human fluids. This assay includes the use of an internal control to avoid false negative results due to the presence of inhibitors. The results obtained show that this assay is robust enough to be used for clinical diagnosis.